Ultrathin CeO2 coating for improved cycling and rate performance of Ni-rich layered LiNi0.7Co0.2Mn0.1O2 cathode materials

In this study, we have successfully coated the CeO₂ nanoparticles (CeONPs) layer onto the surface of the Ni-rich layered LiNi_0.7Co_0.2Mn_0.1O₂ cathode materials by a wet chemical method, which can effectively improve the structural stability of electrode. The X-ray powder diffraction (XRD), transmission electron microscope (TEM), scanning electron microscope (SEM), and X-ray photoelectron spectroscopy (XPS) are used to determine the structure, morphology, elemental composition and electronic state of pristine and surface modified LiNi_0.7Co_0.2Mn_0.1O₂. The electrochemical testing indicates that the 0.3?mol% CeO₂-coated LiNi_0.7Co_0.2Mn_0.1O₂ demonstrates excellent cycling capability and rate performance, the discharge specific capacity is 161.7?mA?h?g^?1 with the capacity retention of 86.42% after 100 cycles at a current rate of 0.5?C, compared to 135.7?mA?h?g^?1 and 70.64% for bare LiNi_0.7Co_0.2Mn_0.1O₂, respectively. Even at 5?C, the discharge specific capacity is still up to 137.1?mA?h?g^?1 with the capacity retention of 69.0%, while the NCM only delivers 95.5?mA?h?g^?1 with the capacity retention of 46.6%. The outstanding electrochemical performance is assigned to the excellent oxidation capacity of CeO₂ which can oxidize Ni²⁺ to Ni³⁺ and Mn³⁺ to Mn⁴⁺ with the result that suppress the occurrence of Li⁺/Ni²⁺ mixing and phase transmission. Furthermore, CeO₂ coating layer can protect the structure to avoid the occurrence of side reaction. The CeO₂-coated composite with enhanced structural stability, cycling capability and rate performance is a promising cathode material candidate for lithium-ion battery.     

Inducing favorable dual-substitution reactivity by doping Mo6+ and F− to enhance electrochemical performance of LiNi0.6Co0.2Mn0.2O2 cathode materials

Lithium-ion batteries are a hot spot of modern energy research due to the advantage of capacity and cost. As a new type of green energy, lithium-ion batteries have a far-reaching influence on the sustainable development of the environment, and the wide application of it can effectively reduce the exploitation of fossil fuels. However, the high specific capacity is also accompanied by some irreversible problems, such as poor cyclic performance and the rapid decay of discharge capacity with high current density. In view of these problems, we employ a dual-modification strategy to co-dope LiNi_0.6Co_0.2Mn_0.2O₂ by Mo⁶⁺ and F^?. The addition of Mo⁶⁺ widens the interval layers and F^? was utilized to lessen the release of lattice oxygen with a purpose of enhancing cyclical stability. After 50 cycles, the dual-substitution of LiNi_0.6Co_0.2Mn_0.2O₂ displayed distinguished capacity retention of 89.6% with 137.7 mAh g^?1 at 0.5C. It's a feasible strategy to enhance the electrochemical performance of cathode materials.     

Preparation of LiNi1/3Co1/3Mn1/3O2/polytriphenylamine cathode composites with enhanced electrochemical performances towards reversible lithium storage

A series of LiNi_1/3Co_1/3Mn_1/3O₂/polytriphenylamine composites were successfully synthesized by ultrasound dispersion method. LiNi_1/3Co_1/3Mn_1/3O₂/polytriphenylamine (5.0?wt%) composite with small and homogeneous particle size exhibited excellent electrochemical performance, which delivered an initial discharge capacity of 223.7?mAh g^?1 with a capacity retention of 84.39% after 100 cycles in the voltage range of 2.5–4.5?V and at a current density of 0.2C. Moreover, an excellent specific discharge capacity of 127.3?mAh g^?1 at a current density 5C indicates a superior rate performance of the LiNi_1/3Co_1/3Mn_1/3O₂/polytriphenylamine (5.0?wt%) composite. The good electrochemical performances of the composite can be attributed to the introduction of polytriphenylamine, which increased electrical conductivity, decreased charge transfer resistance and increased Li⁺ ion diffusion ability. These noteworthy results demonstrated that LiNi_1/3Co_1/3Mn_1/3O₂/polytriphenylamine composites might be potential cathode materials for lithium ion batteries.     

Spray-drying synthesized LiNi0.6Co0.2Mn0.2O2 and its electrochemical performance as cathode materials for lithium ion batteries

Layered LiNi_0.6Co_0.2Mn_0.2O₂ materials were synthesized at different sintering temperatures using spray-drying precursor with molar ratio of Li/Me = 1.04 (Me = transition metals). The influences of sintering temperature on crystal structure, morphology and electrochemical performance of LiNi_0.6Co_0.2Mn_0.2O₂ materials have been characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and charge-discharge test. As a result, material synthesized at 850 °C has excellent electrochemical performance, delivering an initial discharge capacity of 173.1 mAh g^− 1 between 2.8 and 4.3 V at a current density of 16 mA g^− 1 and exhibiting good cycling performance.     

Ultrathin-Y2O3-coated LiNi0.8Co0.1Mn0.1O2 as cathode materials for Li-ion batteries: Synthesis,performance and reversibility

Nickel-rich lithium material LiNi_xCo_yMn_1-x-yO₂(x > 0.6) becomes a new research focus for the next-generation lithium-ion batteries owing to their high operating voltage and high reversible capacity. However, the rate performance and cycling stability of these cathode materials are not satisfactory. Inspired by the characteristics of Y₂O₃ production, a new cathode material with ultrathin-Y₂O₃ coating was introduced to improve the electrochemical performance and storage properties of LiNi_0.8Co_0.1Mn_0.1O₂ for the first time. XRD, scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), energy dispersive spectroscopy (EDS) and XPS were used to mirror the crystal and surface of LiNi_0.8Co_0.1Mn_0.1O₂ particles, results i that a uniform interface formed on as-prepared material. The impacts on the electrochemical properties with or without Y₂O₃ coating are discussed in detail. Notably, galvanostatic discharge-charge tests appear that Y₂O_3-coated sample especially 3% coating displayed a better capacity retention rate of 91.45% after 100 cycles than the bare one of 85.07%.     

Effect of ZnO modification on the performance of LiNi0.5Co0.25Mn0.25O2 cathode material

ZnO was coated on LiNi_0.5Co_0.25Mn_0.25O₂ cathode (positive electrode) material for lithium ion battery via sol–gel method to improve the performance of LiNi_0.5Co_0.25Mn_0.25O₂. The X-ray diffraction (XRD) results indicated that the lattice structure of LiNi_0.5Co_0.25Mn_0.25O₂ was not changed distinctly after surface coating and part of Zn²⁺ might dope into the lattice of the material. Energy dispersive spectroscopy (EDS) and X-ray photoelectron spectroscopy (XPS) proved that ZnO existed on the surface of LiNi_0.5Co_0.25Mn_0.25O₂. Charge and discharge tests showed that the cycle performance and rate capability were improved by ZnO coating, however, the initial capacity decreased dramatically with increasing the amount of ZnO. Differential scanning calorimetry (DSC) results showed that thermal stability of the materials was improved. The XPS spectra after charge–discharge cycles showed that ZnO coated on LiNi_0.5Co_0.25Mn_0.25O₂ promoted the decomposition of the electrolyte at the early stage of charge–discharge cycle to form more stable SEI layer, and it also can scavenge the free acidic HF species from the electrolyte. The electrochemical impedance spectroscopy (EIS) results showed ZnO coating could suppress the augment of charge transfer resistance upon cycling.     

Effects of surface modification on the cycling stability of LiNi0.8Co0.2O2 electrodes by CeO2 coating

A high-performance LiNi_0.8Co_0.2O₂ cathode was successfully fabricated by a sol-gel coating of CeO₂ to the surface of the LiNi_0.8Co_0.2O₂ powder and subsequent heat treatment at 700 °C for 5 h. The surface-modified and pristine LiNi_0.8Co_0.2O₂ powders were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), slow rate cyclic voltammogram (CV), and differential scanning calorimetry (DSC). Unlike pristine LiNi_0.8Co_0.2O₂, the CeO₂-coated LiNi_0.8Co_0.2O₂ cathode exhibits no decrease in its original specific capacity of 182 mAh/g (versus lithium metal) and excellent capacity retention (95% of its initial capacity) between 4.5 and 2.8 V after 55 cycles. The results indicate that the surface treatment should be an effective way to improve the comprehensive properties of the cathode materials for lithium ion batteries.     

Modification of LiNi0.5Co0.2Mn0.3O2 with a NaAlO2 coating produces a cathode with increased long-term cycling performance at a high voltage cutoff

A long-lived cycling property is an important factor for the extensive use of the lithium-ion batteries. In this study, a NaAlO₂ layer was initially coated on the LiNi_0.5Co_0.2Mn_0.3O₂ surface. Electrochemical tests indicate that the coated surface achieves better cycling stability and a higher capacity at 25 °C. In addition, the 1 wt % NaAlO₂-coated sample exhibits the best performance, and it also exhibits a discharge specific capacity of 189.6 mAh∙g⁻¹ at 0.1C in the first cycle. After 800 cycles at 1C, the capacity retention of the 1 wt % NaAlO₂-coated sample is approximately 73.31%, a value that is 21.26% higher than the pristine sample. The electrochemical impedance spectroscopy (EIS) analysis reveals a decrease in the LiNi_0.5Co_0.2Mn_0.3O₂ charge transfer impedance and a significant increase in lithium ion diffusion after the application of the NaAlO₂ coating. The high ion diffusion coefficient and low charge transfer impedance are conducive to the better rate performance of NaAlO₂-coated LiNi_0.5Co_0.2Mn_0.3O₂.     

Highly improved structural stability and electrochemical properties of Ni-rich NCM cathode materials

We report a simple, easy way using WO₃ to build a conductive protective coating layer on the surface of LiNi_0.8Co_0.1Mn_0.1O₂ cathode. The WO₃ coating layer can block direct contact between the LiNi_0.8Co_0.1Mn_0.1O₂ and electrolyte, resulting in suppress the transition metal dissolution and interfacial unwanted reaction on the particle surface. Moreover, WO₃ coating layer allows for the smooth and rapid lithium and electron kinetics. The WO₃ coating improves the electrochemical performance, especially, this way significantly enhances the rate capability of 166.2 mAh g⁻¹ at 6.0C and cyclability of 85.8% after 100 cycles. Therefore, WO₃ coating provides a new breakthrough to improve the structural stability and suppress the resistance for superior electrochemical performances of lithium ion batteries.     

Comparison of AlPO4- and Co3(PO4)2-coated LiNi0.8Co0.2O2 cathode materials for Li-ion battery

Electrochemical and thermal properties of Co₃(PO₄)₂- and AlPO₄-coated LiNi_0.8Co_0.2O₂ cathode materials were compared. AlPO₄-coated LiNi_0.8Co_0.2O₂ cathodes exhibited an original specific capacity of 170.8 mAh g⁻¹ and had a capacity retention (89.1% of its initial capacity) between 4.35 and 3.0 V after 60 cycles at 150 mA g⁻¹. Co₃(PO₄)₂-coated LiNi_0.8Co_0.2O₂ cathodes exhibited an original specific capacity of 177.6 mAh g⁻¹ and excellent capacity retention (91.8% of its initial capacity), which was attributed to a lithium-reactive Co₃(PO₄)₂ coating. The Co₃(PO₄)₂ coating material could react with LiOH and Li₂CO₃ impurities during annealing to form an olivine Li_xCoPO₄ phase on the bulk surface, which minimized any side reactions with electrolytes and the dissolution of Ni⁴⁺ ions compared to the AlPO₄-coated cathode. Differential scanning calorimetry results showed Co₃(PO₄)₂-coated LiNi_0.8Co_0.2O₂ cathode material had a much improved onset temperature of the oxygen evolution of about 218 °C, and a much lower amount of exothermic-heat release compared to the AlPO₄-coated sample.     

Nano SIMS characterization of boron- and aluminum-coated LiNi1/3Co1/3Mn1/3O2 cathode materials for lithium secondary ion batteries

The LiNi_1/3Co_1/3Mn_1/3O₂ powders required for the present study, obtained by coprecipitation method has been surface coated with boron and aluminum. The morphology and crystal structure of powders have been characterized using scanning electron microscopy, X-ray diffraction and X-ray photoelectron spectroscopy techniques. The elemental distribution of the coated samples analyzed by transmission electron microscopy images and nano secondary ion mass spectrometry indicates a thin uniform layer of [B, Al]₂O₃ on the surface of spherical LiNi_1/3Co_1/3Mn_1/3O₂. The surface-modified LiNi_1/3Co_1/3Mn_1/3O₂ has been explored as a cathode material for lithium secondary ion battery applications. The electrochemical charge–discharge results reveal that the capacity retention rate of coated LiNi_1/3Co_1/3Mn_1/3O₂ after 40 cycles at 1 C rate maintains 93% of the initial discharge capacity while the rate of bare LiNi_1/3Co_1/3Mn_1/3O₂ maintains only 88%. It is noticed that the small amounts of boron and aluminum coatings on the surface of LiNi_1/3Co_1/3Mn_1/3O₂ can significantly improve the electrochemical properties of electrode materials because of the suppression of reaction between the cathode and the electrolytes.     

Realization of a high voltage Ni rich layer LiNi0.5Co0.2Mn0.3O2 single crystalline cathode for LIBs by surface modification

Single crystalline ternary cathode material LiNi_0.5Co_0.2Mn_0.3O₂(NCM523) can operate at extremely high voltages and could offer exceptional energy density. The single crystal morphology is less easy to form the cracks and could express better structure stability compared to the polycrystalline counterpart. However, irreversible parasitic side reactions in the interface during cycling may lead to rapid electrochemical degradations. Herein, a simple chemical wet method that modifies the single-crystal NCM523 particles with Al₂O₃ coating is proposed. The coating layer can effectively suppress the phase transformation and irreversible phase transition on the NCM surface during cycling. Furthermore, the cladding layer can prevent the erosion of by-products such as HF. As a result, the Al₂O₃ modified NCM523 delivers a high specific capacity of 192.5mAh g^?1, excellent cycling stability and rate capability. The capacity retention was 91.7% after 50 cycles even at ultra-high cut-off voltage of 4.7 V. This surface engineering strategy paves the way to promote the development of small size single crystal NCM523 materials for next generation LIBs.     

Novel high-capacity hybrid layered oxides NaxLi1.5-xNi0.167Co0.167Mn0.67O2 as promising cathode materials for rechargeable sodium ion batteries

Relatively low capacity is a technological bottleneck of the development of sodium ion batteries. Herein, we present a series of hybrid layered cathode materials Na_xLi_1.5-xNi_0.167Co_0.167Mn_0.67O₂ (x?=?0.5, 0.6, 0.7, 0.8, 0.9, 1) with composite crystalline structures, which are prepared by co-precipitation method. The combined analysis of XRD, SEM and TEM reveals that the materials are composed of P2 structure, α-NaFeO₂ structure and small amount of Li₂MnO₃. Among the as-prepared materials, Na_0.6Li_0.9Ni_0.167Co_0.167Mn_0.67O₂ delivers an initial reversible capacity of 222?mA?h?g^?1 at 20?mA?g^?1. Even at 100?mA?g^?1, it shows a remarkable discharge capacity of 125?mA?h?g^?1 in the first cycle and remains 60?mA?h?g^?1 after 300 cycles. Such high capacity is achieved by the specific composite structure and sodium ions are proved to be able to intercalate/deintercalate in Li_1.5Ni_0.167Co_0.167Mn_0.67O₂ with α-NaFeO₂ structure. The Ex-situ XRD results of Na_0.6Li_0.9Ni_0.167Co_0.167Mn_0.67O₂ in the first cycle show that the P2 structure is well maintained along with irreversible phase transition of α-NaFeO₂ structure, which is responsible for the long-term capacity fading. Owing to the high discharge capacity, the novel hybrid layered oxides Na_xLi_1.5-xNi_0.167Co_0.167Mn_0.67O₂ with composite structures can be considered as promising cathode materials to promote progress toward sodium-ion batteries.     

Synthesis and electrochemical characteristics of Al2O3-coated LiNi1/3Co1/3Mn1/3O2 cathode materials for lithium ion batteries

LiNi_1/3Co_1/3Mn_1/3O₂ cathode materials have been coated with Al₂O₃ nano-particles using sol-gel processing to improve its electrochemical properties. The X-ray diffraction (XRD) pattern of the as-prepared Al₂O₃ nano-particles was indexed to the cubic structure of the γ-Al₂O₃ phase and had an average size of ∼4 nm. The XRD showed that the structure of LiNi_1/3Co_1/3Mn_1/3O₂ was not affected by the Al₂O₃ coating. However, the Al₂O₃ coatings on LiNi_1/3Co_1/3Mn_1/3O₂ improved the cyclic life performance and rate capability without decreasing its initial discharge capacity. These electrochemical properties were also compared with those of LiAlO₂-coated LiNi_1/3Co_1/3Mn_1/3O₂ cathode material. The electrochemical impedance spectroscopy (EIS) was studied to understand the enhanced electrochemical properties of the Al₂O₃-coated LiNi_1/3Co_1/3Mn_1/3O₂ compared to uncoated LiNi_1/3Co_1/3Mn_1/3O₂.     

Effect of niobium doping on the structure and electrochemical performance of LiNi0.5Co0.2Mn0.3O2 cathode materials for lithium ion batteries

Key issues including poor rate capability and limited cycle life span should be addressed for the extended application of LiNi_0.5Co_0.2Mn_0.3O₂ cathode. The suppressed Li⁺/Ni²⁺ site exchange, enlarged LiO₂ inter-slab space and reduced impedance, which could facilitate the structure stability, were achieved by controlled Niobium (Nb) doping and contributed to enhanced performance even at elevated temperature (55 °C). The detailed role of the doped Nb was investigated thoroughly and systematically with the help of XRD, SEM, XPS and related electrochemical tests. The full and accurate results demonstrate that the Li(Ni_0.5Co_0.2Mn_0.3)_0.99Nb_0.01O₂ sample with appropriate Nb doping amount possess high capacity retention of 93.77% after 100 cycles at 1.0 C and improved rate performance with 125.5 mA h g⁻¹ at 5.0 C, which are much better than that of the LiNi_0.5Co_0.2Mn_0.3O₂. Moreover, at high temperature of 55 °C, Nb doping shows more remarkable effect on stabilizing the structure and 88.63% of the initial reversible capacity could be retained, which is ~20% higher than the LiNi_0.5Co_0.2Mn_0.3O₂. This study intensively determines that controlled Nb doping could be effectively maintain the structure stability of advanced LiNi_0.5Co_0.2Mn_0.3O₂ cathode and promote the development of high energy density lithium ion batteries.     

Effects of Al doping on the electrochemical performances of LiNi0.83Co0.12Mn0.05O2 prepared by coprecipitation

The Ni-rich LiNi_0.83Co_0.12Mn_0.05O₂ (NCM83) cathode materials have drawn intensive attention due to the high energy density and low cost. However, Ni-rich LiNi_1-x-yCo_xMn_yO₂ still has the fatal weakness of poor cycle stability, limiting its further wide application. Bulk doping is an effective means to enhance the cycle stability, yet the electrochemical performances are very sensitive to the doping quantity. Here a facile method of co-precipitation is adopted to coat (Ni_0.4Co_0.2Mn_0.4)_1-xAl_x(OH)_2+x on precursor particles of NCM83. Al ions diffuse evenly in the NCM83 particles after sintering. The cells are operated at a high cut-off voltage of 4.5 V. The discharge capacity of NCM83 is 187.8 mAh g^?1, and decays fast with cycles. The doped sample even exhibits a higher discharge capacity of 195 mAh g^?1, and the capacity retention is improved to 83.8% after 200 cycles.     

CeF3-modified LiNi1/3Co1/3Mn1/3O2 cathode material for high-voltage Li-ion batteries

A facile chemical deposition method has been adopted to prepare cerium fluoride (CeF₃) surface modified LiNi_1/3Co_1/3Mn_1/3O₂ as cathode material for lithium-ion batteries. Structure analyses reveal that the surface of LiNi_1/3Co_1/3Mn_1/3O₂ particles is uniformly coated by CeF₃. Electrochemical tests indicate that the optimal CeF₃ content is 1 wt%. The 1 wt% CeF₃-coated LiNi_1/3Co_1/3Mn_1/3O₂ can deliver a discharge capacity of 107.1 mA h g⁻¹ even at 5 C rate, while the pristine does only 57.3 mA h g⁻¹. Compared to the pristine, the 1 wt% CeF₃-coated LiNi_1/3Co_1/3Mn_1/3O₂ exhibits the greatly enhanced capacity and cycling stability in the voltage range of 3.0–4.5 V, which suggests that the CeF₃ coating has the positive effect on the high-voltage application of LiNi_1/3Co_1/3Mn_1/3O₂. According to the analyses from electrochemical impedance spectra, enhanced electrochemical performance is mainly because the stable CeF₃ coating layer can prevent the HF-containing electrolyte from continuously attacking the LiNi_1/3Co_1/3Mn_1/3O₂ cathode and retard the passivating layer growth on the cathode.     

Performance of LiNi1/3Co1/3Mn1/3O2 prepared from spent lithium-ion batteries by a carbonate co-precipitation method

Spherical LiNi_1/3Co_1/3Mn_1/3O₂ cathode particles were resynthesized by a carbonate co-precipitation method using spent lithium-ion batteries (LIBs) as a raw material. The physical characteristics of the Ni_1/3Co_1/3Mn_1/3CO₃ precursor, the (Ni_1/3Co_1/3Mn_1/3)₃O₄ intermediate, and the regenerated LiNi_1/3Co_1/3Mn_1/3O₂ cathode material were investigated by laser particle-size analysis, scanning electron microscopy–energy-dispersive spectroscopy (SEM-EDS), thermogravimetry–differential scanning calorimetry (TG-DSC), X-ray diffraction (XRD), inductively coupled plasma–atomic emission spectroscopy (ICP-AES), and X-ray photoelectron spectroscopy (XPS). The electrochemical performance of the regenerated LiNi_1/3Co_1/3Mn_1/3O₂ was studied by continuous charge–discharge cycling and cyclic voltammetry. The results indicate that the regenerated Ni_1/3Co_1/3Mn_1/3CO₃ precursor comprises uniform spherical particles with a narrow particle-size distribution. The regenerated LiNi_1/3Co_1/3Mn_1/3O₂ comprises spherical particles similar to those of the Ni_1/3Co_1/3Mn_1/3CO₃ precursor, but with a narrower particle-size distribution. Moreover, it has a well-ordered layered structure and a low degree of cation mixing. The regenerated LiNi_1/3Co_1/3Mn_1/3O₂ shows an initial discharge capacity of 163.5 mA h g^?1 at 0.1 C, between 2.7 and 4.3 V; the discharge capacity at 1 C is 135.1 mA h g^?1, and the capacity retention ratio is 94.1% after 50 cycles. Even at the high rate of 5 C, LiNi_1/3Co_1/3Mn_1/3O₂ delivers the high capacity of 112.6 mA h g^?1. These results demonstrate that the electrochemical performance of the regenerated LiNi_1/3Co_1/3Mn_1/3O₂ is comparable to that of a cathode synthesized from fresh materials by carbonate co-precipitation.     

Enhanced cycling performance of Li ion batteries based on Ni-rich cathode materials with LaPO4/Li3PO4 co-modification

The recent development of Li-ion batteries based on Ni-rich cathodes with high specific capacity has generated considerable interest. However, cathodes with a sufficiently high Ni concentration suffer from rapid capacity decay and poor thermal stability during charge/discharge cycling, which represents a substantial challenge toward commercialization. While the application of a coating layer has been demonstrated to be an effective means of solving this issue, this typically increases the complexity and expense of cathode material fabrication. The present work addresses this issue by applying a LaPO₄/Li₃PO₄ (LP) layer on the surface of LiNi_0.83Co_0.11Mn_0.06O₂ cathode materials using a facile in situ coating method. This simple method functions concurrently with the high-temperature solid-state method employed for fabricating the cathode materials using Ni_0.83Co_0.11Mn_0.06(OH)₂ as a precursor with added ammonium dihydrogen phosphate (NH₄H₂PO₄) and lanthanum nitrate (La(NO₃)₃). The modified cathode material reacts with residual Li, and forms a LP layer on the Ni-rich cathode surface, while a proportion of the La³⁺ diffuses into the layered LiNi_0.83Co_0.11Mn_0.06O₂ structure during the modification process. Experimental investigation indicates that the LP layer not only eliminates the residual Li, but also deters the formation of microcracks, and thereby inhibits reactions with the electrolyte during charge/discharge cycling. The LP-modified LiNi_0.83Co_0.11Mn_0.06O₂ sample is demonstrated to attain a capacity retention of 94% and 79.8% after 100 and 500 charge/discharge cycles conducted at 1C, respectively.     

High-voltage electrochemical performance of LiNi0.5Co0.2Mn0.3O2 cathode materials via Al concentration gradient modification

Al₂O₃-modified LiNi_0.5Co_0.2Mn_0.3O₂ cathode material is successfully synthesized via a facile carboxymethyl cellulose (CMC)-assisted wet method followed by a high-temperature calcination process. Al concentration gradient doping and accompanying formation of Al-coating are simultaneously accomplished in the modified samples. XRD and EDS analysis demonstrate that Al element is successfully doped into the crystal lattice with concentration gradient distribution inside the particles, reducing the Li/Ni cation mixing and stabilizing the layered structure. The compact distribution of Al on the surface forms a protective layer between the electrodes and the electrolyte, prohibiting the harmful side reactions and phase transition on the interphase. Compared with the pristine, the modified material with 2000?ppm Al₂O₃ (Al-2000) shows the best high-voltage performance with the capacity retention increased by ~13.3% from 138.3 to 163.0 mAh g^?1 at 1?C in 3.0–4.6?V after 100 cycles. Even under the high current rate of 8?C (1240 mAh g^?1) after 200 cycles, the Al-2000 still exhibits a capacity retention of 88.6%, greater than 80.3% for the pristine. Furthermore, results from the cyclic voltammetry (CV) and the electrochemical impedance spectroscopy (EIS) measurements confirm the roles of the Al₂O₃ modification in decreasing polarization and electrochemical resistances, contributing to the kinetic process of electrodes.