Tailoring Morphology and Structure of Inkjet‐Printed Liquid‐Crystalline Semiconductor/Insulating Polymer Blends for High‐Stability Organic Transistors

Inkjet printing of semiconducting polymers is desirable for realizing low‐cost, large‐area printed electronics. However, sequential inkjet printing methods often suffer from nozzle clogging because the solubility of semiconducting polymers in organic solvents is limited. Here, it is demonstrated that the addition of an insulating polymer to a semiconducting polymer ink greatly enhances the solubility and stability of the ink, leading to the stable ejection of ink droplets. This bicomponent blend comprising a liquid‐crystalline semiconducting copolymer, poly(didodecylquaterthiophene‐alt‐didodecylbithiazole) (PQTBTz‐C12), and an insulating commodity polymer, polystyrene, is extremely useful as a semiconducting layer in organic field‐effect transistors (OFETs), providing fine control over the phase‐separated morphology and structure of the inkjet‐printed film. Tailoring the solubility‐induced phase separation of the two components leads to a bilayer structure consisting of a polystyrene layer on the top and a highly crystalline PQTBTz‐C12 layer on the bottom. The blend film is used as the semiconducting layer in OFETs, reducing the semiconductor content to several tens of pictograms in a single device without degrading the device performance. Furthermore, OFETs based on the PQTBTz‐C12/polystyrene film exhibit much greater environmental and electrical stabilities compared to the films prepared from homo PQTBTz‐C12, mainly due to the self‐encapsulated structure of the blend film.     

Self‐Organization of Inkjet‐Printed Organic Semiconductor Films Prepared in Inkjet‐Etched Microwells

The high‐precision deposition of highly crystalline organic semiconductors by inkjet printing is important for the production of printed organic transistors. Herein, a facile nonconventional lithographic patterning technique is developed for fabricating banks with microwell structures by inkjet printing solvent droplets onto a polymer layer, thereby locally dissolving the polymer to form microwells. The semiconductor ink is then inkjet‐printed into the microwells. In addition to confining the inkjet‐printed organic semiconductor droplets, the microwells provide a platform onto which organic semiconductor molecules crystallize during solvent evaporation. When printed onto the hydrophilic microwells, the inkjet‐printed 6,13‐bis(triisopropylsilylethynyl) pentacene (TIPS_PEN) molecules undergo self‐organization to form highly ordered crystalline structures as a result of contact line pinning at the top corner of the bank and the outward hydrodynamic flow within the drying droplet. By contrast, small crystallites form with relatively poor molecular ordering in the hydrophobic microwells as a result of depinning of the contact line along the walls of the microwells. Because pinning in the hydrophilic microwells occurred at the top corner of the bank, treating the surfaces of the dielectric layer with a hydrophobic organic layer does not disturb the formation of the highly ordered TIPS_PEN crystals. Transistors fabricated on the hydrophilic microwells and the hydrophobic dielectric layer exhibit the best electrical properties, which is explained by the solvent evaporation and crystallization characteristics of the organic semiconductor droplets in the microwell. These results indicate that this technique is suitable for patterning organic semiconductor deposits on large‐area flexible substrates for the direct‐write fabrication of high‐performance organic transistors.     

High‐Performance Top‐Gated Organic Field‐Effect Transistor Memory using Electrets for Monolithic Printed Flexible NAND Flash Memory

High‐performance top‐gated organic field‐effect transistor (OFET) memory devices using electrets and their applications to flexible printed organic NAND flash are reported. The OFETs based on an inkjet‐printed p‐type polymer semiconductor with efficiently chargeable dielectric poly(2‐vinylnaphthalene) (PVN) and high‐k blocking gate dielectric poly(vinylidenefluoride‐trifluoroethylene) (P(VDF‐TrFE)) shows excellent non‐volatile memory characteristics. The superior memory characteristics originate mainly from reversible charge trapping and detrapping in the PVN electret layer efficiently in low‐k/high‐k bilayered dielectrics. A strategy is devised for the successful development of monolithically inkjet‐printed flexible organic NAND flash memory through the proper selection of the polymer electrets (PVN or PS), where PVN/‐ and PS/P(VDF‐TrFE) devices are used as non‐volatile memory cells and ground‐ and bit‐line select transistors, respectively. Electrical simulations reveal that the flexible printed organic NAND flash can be possible to program, read, and erase all memory cells in the memory array repeatedly without affecting the non‐selected memory cells.     

Metal–Insulator–Semiconductor Coaxial Microfibers Based on Self‐Organization of Organic Semiconductor:Polymer Blend for Weavable,Fibriform Organic Field‐Effect Transistors

With the increasing importance of electronic textiles as an ideal platform for wearable electronic devices, requirements for the development of functional electronic fibers with multilayered structures are increasing. In this paper, metal–polymer insulator–organic semiconductor (MIS) coaxial microfibers using the self‐organization of organic semiconductor:insulating polymer blends for weavable, fibriform organic field‐effect transistors (FETs) are demonstrated. A holistic process for MIS coaxial microfiber fabrication, including surface modification of gold microfiber thin‐film coating on the microfiber using a die‐coating system, and the self‐organization of organic semiconductor–insulator polymer blend is presented. Vertical phase‐separation of the organic semiconductor:insulating polymer blend film wrapping the metal microfibers provides a coaxial bilayer structure of gate dielectric (inside) and organic semiconductor (outside) with intimate interfacial contact. It is determined that the fibriform FETs based on MIS coaxial microfiber exhibit good charge carrier mobilities that approach the values of typical devices with planar substrate. It additionally exhibits electrical property uniformity over the entire fiber surface and improved bending durability. Fibriform organic FET embedded in a textile is demonstrated by weaving MIS coaxial microfibers with cotton and conducting threads, which verifies the feasibility of MIS coaxial microfiber for use in electronic textile applications.     

Aligned Polythiophene and its Blend Film by Direct‐Writing for Anisotropic Charge Transport

A combination of patterning and film alignment techniques helps to build multi‐order polymer architecture for application in flexible electronics. A direct‐writing method is employed using microcapillary arrays to prepare semiconducting polymer films with both optical and electrical anisotropy. Not only aligned poly(3‐butylthiophene) (P3BT) nanowires in neat P3BT films, but also aligned P3BT nanowires within a polystyrene (PS) matrix are obtained, which yields an aligned semiconductor/insulator polymer blend with anisotropic charge transport. The field‐effect transistor (FET) mobilities/threshold voltages from both vertical and parallel to alignment directions as well as their dependence on blending ratio are studied. The increased mobility of P3BT/PS blends, as compared with neat P3BT, is observed in both vertical and parallel directions. Using this alignment method, FET mobility and threshold voltage of the semiconductor/insulator polymer blends are comprehensively tuned, from which a digital inverter with gain up to 80 is realized. Therefore, this work not only helps understanding the charge transport mechanism in semiconducting/insulating polymer blends, but also provides an effective approach towards high‐performance field‐effect transistors with tunable mobility and threshold voltage.     

Cover Picture: Self‐Organization of Ink‐jet‐Printed Triisopropylsilylethynyl Pentacene via Evaporation‐Induced Flows in a Drying Droplet (Adv. Funct. Mater. 2/2008)

Charge carrier transport in organic electronic devices is influenced by the crystalline microstructure and morphology of the organic semiconductor film. Evaporation behavior during drying plays a vital role in controlling the film morphology and the distribution of solute in inkjet‐printed films. On p. 229, Kilwon Cho and co‐workers demonstrate the influence of the evaporation‐induced flow in a single droplet on the crystalline microstructure and film morphology of inkjet‐printed 6,13‐bis((triisopropylsilylethynyl) pentacene. The results provide an excellent method for direct‐write fabrication of high‐performance organic electronics. We have demonstrated the influence of evaporation‐induced flow in a single droplet on the crystalline microstructure and film morphology of an ink‐jet‐printed organic semiconductor, 6,13‐bis((triisopropylsilylethynyl) pentacene (TIPS_PEN), by varying the composition of the solvent mixture. The ringlike deposits induced by outward convective flow in the droplets have a randomly oriented crystalline structure. The addition of dichlorobenzene as an evaporation control agent results in a homogeneous film morphology due to slow evaporation, but the molecular orientation of the film is undesirable in that it is similar to that of the ring‐deposited films. However, self‐aligned TIPS_PEN crystals with highly ordered crystalline structures were successfully produced when dodecane was added. Dodecane has a high boiling point and a low surface tension, and its addition to the solvent results in a recirculation flow in the droplets that is induced by a Marangoni flow (surface‐tension‐driven flow), which arises during the drying processes in the direction opposite to the convective flow. The field‐effect transistors fabricated with these self‐aligned crystals via ink‐jet printing exhibit significantly improved performance with an average effective field‐effect mobility of 0.12 cm² V^–1 s^–1. These results demonstrate that with the choice of appropriate solvent ink‐jet printing is an excellent method for the production of organic semiconductor films with uniform morphology and desired molecular orientation for the direct‐write fabrication of high‐performance organic electronics.     

Control of the Morphology and Structural Development of Solution‐Processed Functionalized Acenes for High‐Performance Organic Transistors

Solution‐processable functionalized acenes have received special attention as promising organic semiconductors in recent years because of their superior intermolecular interactions and solution‐processability, and provide useful benchmarks for organic field‐effect transistors (OFETs). Charge‐carrier transport in organic semiconductor thin films is governed by their morphologies and molecular orientation, so self‐assembly of these functionalized acenes during solution processing is an important challenge. This article discusses the charge‐carrier transport characteristics of solution‐processed functionalized acene transistors and, in particular, focuses on the fine control of the films' morphologies and structural evolution during film‐deposition processes such as inkjet printing and post‐deposition annealing. We discuss strategies for controlling morphologies and crystalline microstructure of soluble acenes with a view to fabricating high‐performance OFETs.     

Self‐Assembled,Millimeter‐Sized TIPS‐Pentacene Spherulites Grown on Partially Crosslinked Polymer Gate Dielectric

Here, a highly crystalline and self‐assembled 6,13‐bis(triisopropylsilylethynyl) pentacene (TIPS‐Pentacene) thin films formed by simple spin‐coating for the fabrication of high‐performance solution‐processed organic field‐effect transistors (OFETs) are reported. Rather than using semiconducting organic small‐molecule–insulating polymer blends for an active layer of an organic transistor, TIPS‐Pentacene organic semiconductor is separately self‐assembled on partially crosslinked poly‐4‐vinylphenol:poly(melamine‐co‐formaldehyde) (PVP:PMF) gate dielectric, which results in a vertically segregated semiconductor‐dielectric film with millimeter‐sized spherulite‐crystalline morphology of TIPS‐Pentacene. The structural and electrical properties of TIPS‐Pentacene/PVP:PMF films have been studied using a combination of polarized optical microscopy, atomic force microscopy, 2D‐grazing incidence wide‐angle X‐ray scattering, and secondary ion mass spectrometry. It is finally demonstrated a high‐performance OFETs with a maximum hole mobility of 3.40 cm² V^?1 s^?1 which is, to the best of our knowledge, one of the highest mobility values for TIPS‐Pentacene OFETs fabricated using a conventional solution process. It is expected that this new deposition method would be applicable to other small molecular semiconductor–curable polymer gate dielectric systems for high‐performance organic electronic applications.     

Vertically Segregated Structure and Properties of Small Molecule–Polymer Blend Semiconductors for Organic Thin‐Film Transistors

A comprehensive structure and performance study of thin blend films of the small‐molecule semiconductor, 2,8‐difluoro‐5,11‐bis(triethylsilylethynyl)anthradithiophene (diF‐TESADT), with various insulating binder polymers in organic thin‐film transistors is reported. The vertically segregated composition profile and nanostructure in the blend films are characterized by a combination of complementary experimental methods including grazing incidence X‐ray diffraction, neutron reflectivity, variable angle spectroscopic ellipsometry, and near edge X‐ray absorption fine structure spectroscopy. Three polymer binders are considered: atactic poly(α‐methylstyrene), atactic poly(methylmethacrylate), and syndiotactic polystyrene. The choice of polymer can strongly affect the vertical composition profile and the extent of crystalline order in blend films due to the competing effects of confinement entropy, interaction energy with substrate surfaces, and solidification kinetics. The variations in the vertically segregated composition profile and crystalline order in thin blend films explain the significant impacts of binder polymer choice on the charge carrier mobility of these films in the solution‐processed bottom‐gate/bottom‐contact thin‐film transistors.     

Charge‐Carrier Density Independent Mobility in Amorphous Fluorene‐Triarylamine Copolymers

A charge‐carrier density dependent mobility has been predicted for amorphous, glassy energetically disordered semiconducting polymers, which would have considerable impact on their performance in devices. However, previous observations of a density dependent mobility are complicated by the polycrystalline materials studied. Here charge transport in field‐effect transistors and diodes of two amorphous, glassy fluorene‐triarylamine copolymers is investigated, and the results explored in terms of a charge‐carrier density dependent mobility model. The nondispersive nature of the time‐of‐flight (TOF) transients and analysis of dark injection transient results and transistor transfer characteristics indicate a charge‐carrier density independent mobility in both the low‐density diode and the high‐density transistor regimes. The mobility values for optimized transistors are in good agreement with the TOF values at the same field, and both have the same temperature dependency. The measured transistor mobility falls two to three orders of magnitude below that predicted from the charge‐carrier density dependent model, and does not follow the expected power‐law relationship. The experimental results for these two amorphous polymers are therefore consistent with a charge‐carrier density independent mobility, and this is discussed in terms of polaron‐dominated hopping and interchain correlated disorder.     

Systematic Study of Widely Applicable N‐Doping Strategy for High‐Performance Solution‐Processed Field‐Effect Transistors

A specific design for solution‐processed doping of active semiconducting materials would be a powerful strategy in order to improve device performance in flexible and/or printed electronics. Tetrabutylammonium fluoride and tetrabutylammonium hydroxide contain Lewis base anions, F^? and OH^?, respectively, which are considered as organic dopants for efficient and cost‐effective n‐doping processes both in n‐type organic and nanocarbon‐based semiconductors, such as poly[[N,N′‐bis(2‐octyldodecyl)‐naphthalene‐1,4,5,8‐bis(dicarboximide)‐2,6‐diyl]‐alt‐5,5′‐(2,2′‐bithiophene)] (P(NDI2OD‐T2)) and selectively dispersed semiconducting single‐walled carbon nanotubes by π‐conjugated polymers. The dramatic enhancement of electron transport properties in field‐effect transistors is confirmed by the effective electron transfer from the dopants to the semiconductors as well as controllable onset and threshold voltages, convertible charge‐transport polarity, and simultaneously showing excellent device stabilities under ambient air and bias stress conditions. This simple solution‐processed chemical doping approach could facilitate the understanding of both intrinsic and extrinsic charge transport characteristics in organic semiconductors and nanocarbon‐based materials, and is thus widely applicable for developing high‐performance organic and printed electronics and optoelectronics devices.     

Polymer Dielectrics and Orthogonal Solvent Effects for High‐Performance Inkjet‐Printed Top‐Gated P‐Channel Polymer Field‐Effect Transistors

We investigated the effects of a gate dielectric and its solvent on the characteristics of top‐gated organic field‐effect transistors (OFETs). Despite the rough top surface of the inkjet‐printed active features, the charge transport in an OFET is still favorable, with no significant degradation in performance. Moreover, the characteristics of the OFETs showed a strong dependency on the gate dielectrics used and its orthogonal solvents. Poly(3‐hexylthiophene) OFETs with a poly(methyl methacrylate) dielectric showed typical p‐type OFET characteristics. The selection of gate dielectric and solvent is very important to achieve high‐performance organic electronic circuits.     

Optically‐Pumped Lasing in Hybrid Organic–Inorganic Light‐Emitting Diodes

Here, the use of metal oxide layers both for charge transport and injection into an emissive semiconducting polymer and also for the control of the in‐plane waveguided optical modes in light‐emitting diodes (LEDs) is reported. The high refractive index of zinc oxide is used to confine these modes away from the absorbing electrodes, and include a nano‐imprinted grating in the polymer layer to introduce distributed feedback and enhance optical out‐coupling. These structures show a large increase in the luminescence efficiency over conventional devices, with photoluminescence efficiency increased by up to 45%. Furthermore, optically‐pumped lasing in hybrid oxide polymer LEDs is demonstrated. A tuneable lasing emission is also obtained in a single device structure by employing a graduated thickness of a zinc oxide inter‐layer. This demonstrates the scope for using such architectures to improve the external efficiency of organic semiconductor LEDs, and opens new possibilities for the realization of polymer injection lasers.     

Low‐Temperature‐Processed Printed Metal Oxide Transistors Based on Pure Aqueous Inks

Additive patterning of transparent conducting metal oxides at low temperatures is a critical step in realizing low‐cost transparent electronics for display technology and photovoltaics. In this work, inkjet‐printed metal oxide transistors based on pure aqueous chemistries are presented. These inks readily convert to functional thin films at lower processing temperatures (T ≤ 250 °C) relative to organic solvent‐based oxide inks, facilitating the fabrication of high‐performance transistors with both inkjet‐printed transparent electrodes of aluminum‐doped cadmium oxide (ACO) and semiconductor (InO_x ). The intrinsic fluid properties of these water‐based solutions enable the printing of fine features with coffee‐ring free line profiles and smoother line edges than those formed from organic solvent‐based inks. The influence of low‐temperature annealing on the optical, electrical, and crystallographic properties of the ACO electrodes is investigated, as well as the role of aluminum doping in improving these properties. Finally, the all‐aqueous‐printed thin film transistors (TFTs) with inkjet‐patterned semiconductor (InO_x ) and source/drain (ACO) layers are characterized, which show ideal low contact resistance (R _c < 160 Ω cm) and competitive transistor performance (µ _lin up to 19 cm² V^?1 s^?1, Subthreshold Slope (SS) ≤150 mV dec^?1) with only low‐temperature processing (T ≤ 250 °C).     

Room‐Temperature Printing of Organic Thin‐Film Transistors with π‐Junction Gold Nanoparticles

Printing semiconductor devices under ambient atmospheric conditions is a promising method for the large‐area, low‐cost fabrication of flexible electronic products. However, processes conducted at temperatures greater than 150 °C are typically used for printed electronics, which prevents the use of common flexible substrates because of the distortion caused by heat. The present report describes a method for the room‐temperature printing of electronics, which allows thin‐film electronic devices to be printed at room temperature without the application of heat. The development of π‐junction gold nanoparticles as the electrode material permits the room‐temperature deposition of a conductive metal layer. Room‐temperature patterning methods are also developed for the Au ink electrodes and an active organic semiconductor layer, which enables the fabrication of organic thin‐film transistors through room‐temperature printing. The transistor devices printed at room temperature exhibit average field‐effect mobilities of 7.9 and 2.5 cm² V^?1 s^?1 on plastic and paper substrates, respectively. These results suggest that this fabrication method is very promising as a core technology for low‐cost and high‐performance printed electronics.     

Dual layer semiconducting nanocomposite of silicon nanowire and polythiophene for organic-based field effect transistors

We investigate a dual layer active channel of random distributed intrinsic silicon nanowires and solution processing semiconducting polythiophene polymers for organic-based field effect transistors. Primary results show that low density silicon nanowire networks could enhance the effective charge carrier mobility of polythiophene transistors by a factor of six, suggesting that these nanowires act as rapid one-dimensional charge transport bridges in the active channel. Moreover, increasing the nanowire loading in the dual layer nanocomposite could further lessen the transistor hysteresis. The lifetime test of nanowire-polythiophene devices is found to be more sustainable with respect to that of pristine polythiophene in ambient air. These results indicate that semiconducting nanowires should be considered as a viable additive to active channel for next-generation organic field effect transistors.     

Tuning the Charge Carrier Polarity of Organic Transistors by Varying the Electron Affinity of the Flanked Units in Diketopyrrolopyrrole‐Based Copolymers

Fine‐tuning of the charge carrier polarity in organic transistors is an important step toward high‐performance organic complementary circuits and related devices. Here, three new semiconducting polymers, namely, pDPF‐DTF2, pDPSe‐DTF2, and pDPPy‐DTF2, are designed and synthesized using furan, selenophene, and pyridine flanking group‐based diketopyrrolopyrrole cores, respectively. Upon evaluating their electrical properties in transistor devices, the best performance has been achieved for pDPSe‐DTF2 with the highest and average hole mobility of 1.51 and 1.22 cm² V^?1 s^?1, respectively. Most intriguingly, a clear charge‐carrier‐polarity change is observed when the devices are measured under vacuum. The pDPF‐DTF2 polymer exhibits a balanced ambipolar performance with the µ_h/µ_e ratio of 1.9, whereas pDPSe‐DTF2 exhibits p‐type dominated charge carrier transport properties with the µ_h/µ_e ratio of 26.7. Such a charge carrier transport change is due to the strong electron‐donating nature of the selenophene. Furthermore, pDPPy‐DTF2 with electron‐withdrawing pyridine flanking units demonstrates unipolar n‐type charge transport properties with an electron mobility as high as 0.20 cm² V^?1 s^?1. Overall, this study demonstrates a simple yet effective approach to switch the charge carrier polarity in transistors by varying the electron affinity of flanking groups of the diketopyrrolopyrrole unit.     

Flexible Near‐Infrared Plastic Phototransistors with Conjugated Polymer Gate‐Sensing Layers

Flexible near‐infrared (NIR) light‐sensing detectors are strongly required in the fast‐growing flexible electronics era, because they can serve as a vision system like eyes in various innovative applications including humanoid robots. Recently, keen interest has been paid to organic phototransistors due to their unique signal amplification and active matrix driving features over organic photodiodes. However, conventional NIR‐sensing organic phototransistors suffer from the limited use of organic materials because the channel layers play a dual role in both charge transport and sensing so that organic semiconducting materials with reasonably high charge mobility can be applied only. Here, it is demonstrated that a conjugated polymer, poly[{2,5‐bis‐(2‐ethylhexyl)‐3,6‐bis‐(thien‐2‐yl)‐pyrrolo[3,4‐c]pyrrole‐1,4‐diyl}‐co‐{2,2′‐(2,1,3‐benzothiadiazole)]‐5,5′‐diyl}] (PEHTPPD‐BT), which exhibits no transistor performance as a channel layer, can stably detect a NIR light (up to 1000 nm) as a gate‐sensing layer (GSL) when it is placed between gate‐insulating layers and gate electrodes. The flexible array (10 × 10) detectors with the PEHTPPD‐BT GSLs could effectively sense NIR light without visible light interference by applying visible light cut films.     

Organic Light‐Emitting Diodes with Field‐Effect‐Assisted Electron Transport Based on α‐bi;,ω‐bi;‐Diperfluorohexyl‐quaterthiophene

Materials commonly used in the carrier transport layers of organic light‐emitting diodes, where transport occurs through the bulk, are in general very different from materials used in organic field‐effect transistors, where transport takes place in a very thin accumulation channel. In this paper, the use of a high‐performance electron‐conducting field‐effect transistor material, diperfluorohexyl‐substituted quaterthiophene (DFH‐4T), as the electron‐transporting material in an organic light‐emitting diode structure is investigated. The organic light‐emitting diode has an electron accumulation layer in DFH‐4T at the organic hetero‐interface with the host of the light‐emitting layer, tris(8‐hydroxyquinoline) aluminum (Alq₃). This electron accumulation layer is used to transport electrons and inject them into the active emissive host‐guest layer. By optimizing the growth conditions of DFH‐4T for electron transport at the organic hetero‐interface, high electron current densities of 750 A cm^?2 are achieved in this innovative light‐emitting structure.     

Printed and Electrochemically Gated,High‐Mobility,Inorganic Oxide Nanoparticle FETs and Their Suitability for High‐Frequency Applications

Solution‐processed or printed n‐channel field‐effect transistors (FETs) with high performance are not reported very often in the literature due to the scarcity of high‐mobility n‐type organic semiconductors. On the other hand, low‐temperature processed n‐channel metal oxide semiconductor (NMOS) transistors from electron conducting inorganic‐oxide nanoparticles show reduced‐performance and low mobility because of large channel roughness at the channel‐dielectric interface. Here, a method to produce ink‐jet printed high performance NMOS transistor devices using inorganic‐oxide nanoparticles as the transistor channel in combination with a 3D electrochemical gating (EG) via printed composite solid polymer electrolytes is presented. The printed FETs produced show a device mobility value in excess of 5 cm² V^?1 s^?1, even though the root mean square (RMS) roughness of the nanoparticulate channel exceeds 15 nm. Extensive studies on the frequency dependent polarizability of composite polymer electrolyte capacitors show that the maximum attainable speed in such printed, long channel transistors is not limited by the ionic conductivity of the electrolytes. Therefore, the approach of combining printable, high‐quality oxide nanoparticles and the composite solid polymer electrolytes, offers the possibility to fully utilize the large mobility of oxide semiconductors to build all‐printed and high‐speed devices. The high polarizability of printable polymer electrolytes brings down the drive voltages to ≤1 V, making such FETs well‐suited for low‐power, battery compatible circuitry.