Red,Green, and Blue Light‐Emitting Polyfluorenes Containing a Dibenzothiophene‐S,S‐Dioxide Unit and Efficient High‐Color‐Rendering‐Index White‐Light‐Emitting Diodes Made Therefrom

A series of blue (B), green (G) and red (R) light‐emitting, 9,9‐bis(4‐(2‐ethyl‐hexyloxy)phenyl)fluorene (PPF) based polymers containing a dibenzothiophene‐S,S‐dioxide (SO) unit (PPF‐SO polymer), with an additional benzothiadiazole (BT) unit (PPF‐SO‐BT polymer) or a 4,7‐di(4‐hexylthien‐2‐yl)‐benzothiadiazole (DHTBT) unit (PPF‐SO‐DHTBT polymer) are synthesized. These polymers exhibit high fluorescence yields and good thermal stability. Light‐emitting diodes (LEDs) using PPF‐SO25, PPF‐SO15‐BT1, and PPF‐SO15‐DHTBT1 as emission polymers have maximum efficiencies LE_max = 7.0, 17.6 and 6.1 cd A^?1 with CIE coordinates (0.15, 0.17), (0.37, 0.56) and (0.62, 0.36), respectively. 1D distributed feedback lasers using PPF‐SO30 as the gain medium are demonstrated, with a wavelength tuning range 467 to 487 nm and low pump energy thresholds (≥18 nJ). Blending different ratios of B (PPF‐SO), G (PPF‐SO‐BT) and R (PPF‐SO‐DHTBT) polymers allows highly efficient white polymer light‐emitting diodes (WPLEDs) to be realized. The optimized devices have an attractive color temperature close to 4700 K and an excellent color rendering index (CRI) ≥90. They are relatively stable, with the emission color remaining almost unchanged when the current densities increase from 20 to 260 mA cm^?2. The use of these polymers enables WPLEDs with a superior trade‐off between device efficiency, CRI, and color stability.     

Highly Efficient Pure‐White‐Light‐Emitting Diodes from a Single Polymer: Polyfluorene with Naphthalimide Moieties

Light‐emitting diodes exhibiting efficient pure‐white‐light electroluminescence have been successfully developed by using a single polymer: polyfluorene derivatives with 1,8‐naphthalimide chromophores chemically doped onto the polyfluorene backbones. By adjusting the emission wavelength of the 1,8‐naphthalimide components and optimizing the relative content of 1,8‐naphthalimide derivatives in the resulting polymers, white‐light electroluminescence from a single polymer, as opposed to a polymer blend, has been obtained in a device with a configuration of indium tin oxide/poly(3,4‐ethylenedioxythiophene)(50 nm)/polymer(80 nm)/Ca(10 nm)/Al(100 nm). The device exhibits Commission Internationale de l'Eclairage coordinates of (0.32,0.36), a maximum brightness of 11 900 cd m^–2, a current efficiency of 3.8 cd A^–1, a power efficiency of 2.0 lm W^–1, an external quantum efficiency of 1.50 %, and quite stable color coordinates at different driving voltages, even at high luminances of over 5000 cd m^–2.     

Electron‐Enhanced Hole Injection in Blue Polyfluorene‐Based Polymer Light‐Emitting Diodes

It has recently been reported that, after electrical conditioning, an ohmic hole contact is formed in poly(9,9‐dioctylfluorene) (PFO)‐based polymer light‐emitting diodes (PLED), despite the large hole‐injection barrier obtained with a poly(styrene sulfonic acid)‐doped poly(3,4‐ethylenedioxythiophene) (PEDOT:PSS) anode. We demonstrate that the initial current at low voltages in a PEDOT:PSS/PFO‐based PLED is electron dominated. The voltage at which the hole injection is enhanced strongly depends on the electron‐transport properties of the device, which can be modified by the replacement of reactive end groups by monomers in the synthesis. Our measurements reveal that the switching voltage of the PLED is governed by the electron concentration at the PEDOT:PSS/PFO contact. The switching effect in PFO is only observed for a PEDOT:PSS hole contact and not for other anodes such as indium tin oxide or Ag.     

Alternating‐Current MXene Polymer Light‐Emitting Diodes

MXenes (Ti₃C₂) are 2D transition‐metal carbides and carbonitrides with high conductivity and optical transparency. However, transparent MXene electrodes suitable for polymer light‐emitting diodes (PLEDs) have rarely been demonstrated. With the discovery of the excellent electrical stability of MXene under an alternating current (AC), herein, PLEDs that employ MXene electrodes and exhibit high performance under AC operation (AC MXene PLEDs) are presented. The PLED exhibits a turn‐on voltage, current efficiency, and brightness of 2.1 V, 7 cd A^?1, and 12 547 cd m^?2, respectively, when operated under AC with a frequency of 1 kHz. The results indicate that the undesirable electric breakdown associated with heat arising from the poor interface of the MXene with a hole transport layer in the direct‐current mode is efficiently suppressed by the transient injection of carriers accompanied by the alternating change of the electric polarity under the AC, giving rise to reliable light emission with a high efficiency. The solution‐processable MXene electrode can be readily fabricated on a flexible polymer substrate, allowing for the development of a mechanically flexible AC MXene PLED with a higher performance than flexible PLEDs employing solution‐processed nanomaterial‐based electrodes such as carbon nanotubes, reduced graphene oxide, and Ag nanowires.     

Electron‐Rich Alcohol‐Soluble Neutral Conjugated Polymers as Highly Efficient Electron‐Injecting Materials for Polymer Light‐Emitting Diodes

We report the design and synthesis of three alcohol‐soluble neutral conjugated polymers, poly[9,9‐bis(2‐(2‐(2‐diethanolaminoethoxy) ethoxy)ethyl)fluorene] (PF‐OH), poly[9,9‐bis(2‐(2‐(2‐diethanol‐aminoethoxy)ethoxy)ethyl)fluorene‐alt‐4,4′‐phenylether] (PFPE‐OH) and poly[9,9‐bis(2‐(2‐(2‐diethanolaminoethoxy) ethoxy)ethyl)fluorene‐alt‐benzothiadizole] (PFBT‐OH) with different conjugation length and electron affinity as highly efficient electron injecting and transporting materials for polymer light‐emitting diodes (PLEDs). The unique solubility of these polymers in polar solvents renders them as good candidates for multilayer solution processed PLEDs. Both the fluorescent and phosphorescent PLEDs based on these polymers as electron injecting/transporting layer (ETL) were fabricated. It is interesting to find that electron‐deficient polymer (PFBT‐OH) shows very poor electron‐injecting ability compared to polymers with electron‐rich main chain (PF‐OH and PFPE‐OH). This phenomenon is quite different from that obtained from conventional electron‐injecting materials. Moreover, when these polymers were used in the phosphorescent PLEDs, the performance of the devices is highly dependent on the processing conditions of these polymers. The devices with ETL processed from water/methanol mixed solvent showed much better device performance than the devices processed with methanol as solvent. It was found that the erosion of the phosphorescent emission layer could be greatly suppressed by using water/methanol mixed solvent for processing the polymer ETL. The electronic properties of the ETL could also be influenced by the processing conditions. This offers a new avenue to improve the performance of phosphorescent PLEDs through manipulating the processing conditions of these conjugated polymer ETLs.     

Surface‐Directed Phase Separation of Conjugated Polymer Blends for Efficient Light‐Emitting Diodes

The ability to control organic‐organic interfaces in conjugated polymer blends is critical for further device improvement. Here, we control the phase separation in blends of poly(9,9‐di‐n‐octylfluorene‐alt‐benzothiadiazole) (F8BT) and poly(9,9‐di‐n‐octylfluorene‐alt‐(1,4‐phenylene‐((4‐sec‐butylphenyl)imino)‐1,4‐phenylene) (TFB) via chemical modification of the substrate by microcontact printing of octenyltrichlorosilane molecules. The lateral phase‐separated structures in the blend film closely replicate the underlying micrometer‐scale chemical pattern. We found nanometer‐scale vertical segregation of the polymers within both lateral domains, with regions closer to the substrate being substantially pure phases of either polymer. Such phase separation has important implications for the performance of light‐emitting diodes fabricated using these patterned blend films. In the absence of a continuous TFB wetting layer at the substrate interface, as typically formed in spin‐coated blend films, charge carrier injection is confined in the well‐defined TFB‐rich domains. This confinement leads to high electroluminescence efficiency, whereas the overall reduction in the roughness of the patterned blend film results in slower decay of device efficiency at high voltages. In addition, the amount of surface out‐coupling of light in the forward direction observed in these blend devices is found to be strongly correlated to the distribution of periodicity of the phase‐separated structures in the active layer.     

n‐Doping of a Low‐Electron‐Affinity Polymer Used as an Electron‐Transport Layer in Organic Light‐Emitting Diodes

n‐Doping electron‐transport layers (ETLs) increases their conductivity and improves electron injection into organic light‐emitting diodes (OLEDs). Because of the low electron affinity and large bandgaps of ETLs used in green and blue OLEDs, n‐doping has been notoriously more difficult for these materials. In this work, n‐doping of the polymer poly[(9,9‐dioctylfluorene‐2,7‐diyl)‐alt‐(benzo[2,1,3]thiadiazol‐4,7‐diyl)] (F8BT) is demonstrated via solution processing, using the air‐stable n‐dopant (pentamethylcyclopentadienyl)(1,3,5‐trimethylbenzene)ruthenium dimer [RuCp*Mes]₂. Undoped and doped F8BT films are characterized using ultraviolet and inverse photoelectron spectroscopy. The ionization energy and electron affinity of the undoped F8BT are found to be 5.8 and 2.8 eV, respectively. Upon doping F8BT with [RuCp*Mes]₂, the Fermi level shifts to within 0.25 eV of the F8BT lowest unoccupied molecular orbital, which is indicative of n‐doping. Conductivity measurements reveal a four orders of magnitude increase in the conductivity upon doping and irradiation with ultraviolet light. The [RuCp*Mes]₂‐doped F8BT films are incorporated as an ETL into phosphorescent green OLEDs, and the luminance is improved by three orders of magnitude when compared to identical devices with an undoped F8BT ETL.     

Extremely Efficient White Organic Light‐Emitting Diodes for General Lighting

Highly power‐efficient white organic light‐emitting diodes (OLEDs) are still challenging to make for applications in high‐quality displays and general lighting due to optical confinement and energy loss during electron‐photon conversion. Here, an efficient white OLED structure is shown that combines deterministic aperiodic nanostructures for broadband quasi‐omnidirectional light extraction and a multilayer energy cascade structure for energy‐efficient photon generation. The external quantum efficiency and power efficiency are raised to 54.6% and 123.4 lm W^?1 at 1000 cd m^?2. An extremely small roll‐off in efficiency at high luminance is also obtained, yielding a striking value of 106.5 lm W^?1 at 5000 cd m^?2. In addition to a substantial increase in efficiency, this device structure simultaneously offers the superiority of angular color stability over the visible wavelength range compared to conventional OLEDs. It is anticipated that these findings could open up new opportunities to promote white OLEDs for commercial applications.     

Microwave‐Assisted Preparation of White Fluorescent Graphene Quantum Dots as a Novel Phosphor for Enhanced White‐Light‐Emitting Diodes

Graphene quantum dots (GQDs) with white fluorescence are synthesized by a microwave‐assisted hydrothermal method using graphite as the precursor. A solution‐processed white‐light‐emitting diode (WLED) is fabricated using the as‐prepared white fluorescent GQDs (white‐light‐emitting graphene quantum dots, WGQDs) doped 4,4‐bis(carbazol‐9‐yl)biphenyl as the emissive layer. White‐light emission is obtained from the WLED with 10 wt% doping concentration of WGQDs, which shows a luminance of 200 cd m^?2 at the applied voltage of 11–14 V. Importantly, an external quantum efficiency of 0.2% is achieved, which is the highest among all the reported WLED based on GQDs or carbon dots. The results demonstrate that WGQDs as a novel phosphor may open up a new avenue to develop the environmentally friendly WLEDs for practical application in solid‐state lighting.     

Barium Hydroxide as an Interlayer Between Zinc Oxide and a Luminescent Conjugated Polymer for Light‐Emitting Diodes

A study of hybrid light‐emitting diodes (HyLEDs) fabricated with and without solution‐processible Cs₂CO₃ and Ba(OH)₂ inorganic interlayers is presented. The interlayers are deposited between a zinc oxide electron‐injection layer and a fluorescent emissive polymer poly(9‐dioctyl fluorine–alt‐benzothiadiazole) (F8BT) layer, with a thermally evaporated MoO₃/Au layer used as top anode contact. In comparison to Cs₂CO₃, the Ba(OH)₂ interlayer shows improved charge carrier balance in bipolar devices and reduced exciton quenching in photoluminance studies at the ZnO/Ba(OH)₂/F8BT interface compared to the Cs₂CO₃ interlayer. A luminance efficiency of ≈28 cd A^?1 (external quantum efficiency (EQE) ≈ 9%) is achieved for ≈1.2 μm thick single F8BT layer based HyLEDs. Enhanced out‐coupling with the aid of a hemispherical lens allows further efficiency improvement by a factor of 1.7, increasing the luminance efficiency to ≈47cd A^?1, corresponding to an EQE of 15%. The photovoltaic response of these structures is also studied to gain an insight into the effects of interfacial properties on the photoinduced charge generation and back‐recombination, which reveal that Ba(OH)₂ acts as better hole blocking layer than the Cs₂CO₃ interlayer.     

Organic Light‐Emitting Diodes with a White‐Emitting Molecule: Emission Mechanism and Device Characteristics

The unique and unprecedented electroluminescence behavior of the white‐emitting molecule 3‐(1‐(4‐(4‐(2‐(2‐hydroxyphenyl)‐4,5‐diphenyl‐1H‐imidazol‐1‐yl)phenoxy)phenyl)‐4,5‐diphenyl‐1H‐imidazol‐2‐yl)naphthalen‐2‐ol (W1), fluorescence emission from which is controlled by the excited‐state intramolecular proton transfer (ESIPT) is investigated. W1 is composed of covalently linked blue‐ and yellow‐color emitting ESIPT moieties between which energy transfer is entirely frustrated. It is demonstrated that different emission colors (blue, yellow, and white) can be generated from the identical emitter W1 in organic light‐emitting diode (OLED) devices. Charge trapping mechanism is proposed to explain such a unique color‐tuned emission from W1. Finally, the device structure to create a color‐stable, color reproducible, and simple‐structured white organic light‐emitting diode (WOLED) using W1 is investigated. The maximum luminance efficiency, power efficiency, and luminance of the WOLED were 3.10 cd A^?1, 2.20 lm W^?1, 1 092 cd m^?2, respectively. The WOLED shows white‐light emission with the Commission Internationale de l′Eclairage (CIE) chromaticity coordinates (0.343, 0.291) at a current level of 10 mA cm^?2. The emission color is high stability, with a change of the CIE chromaticity coordinates as small as (0.028, 0.028) when the current level is varied from 10 to 100 mA cm^?2.     

Conjugated Polyelectrolyte Hybridized ZnO Nanoparticles as a Cathode Interfacial Layer for Efficient Polymer Light‐Emitting Diodes

Alkoxy side‐chain tethered polyfluorene conjugated polyelectrolyte (CPE), poly[(9,9‐bis((8‐(3‐methyl‐1‐imidazolium)octyl)‐2,7‐fluorene)‐alt‐(9,9‐bis(2‐(2‐methoxyethoxy)ethyl)‐fluorene)] dibromide (F8imFO₄), is utilized to obtain CPE‐hybridized ZnO nanoparticles (NPs) (CPE:ZnO hybrid NPs). The surface defects of ZnO NPs are passivated through coordination interactions with the oxygen atoms of alkoxy side‐chains and the bromide anions of ionic pendent groups from F8imFO₄ to the oxygen vacancies of ZnO NPs, and thereby the fluorescence quenching at the interface of yellow‐emitting poly(p‐phenylene vinylene)/CPE:ZnO hybrid NPs is significantly reduced at the CPE concentration of 4.5 wt%. Yellow‐emitting polymer light‐emitting diodes (PLEDs) with CPE(4.5 wt%):ZnO hybrid NPs as a cathode interfacial layer show the highest device efficiencies of 11.7 cd A^?1 at 5.2 V and 8.6 lm W^?1 at 3.8 V compared to the ZnO NP only (4.8 cd A^?1 at 7 V and 2.2 lm W^?1 at 6.6 V) or CPE only (7.3 cd A^?1 at 5.2 V and 4.9 lm W^?1 at 4.2 V) devices. The results suggest here that the CPE:ZnO hybrid NPs has a great potential to improve the device performance of organic electronics.     

Device Physics of White Polymer Light‐Emitting Diodes

The charge transport and recombination in white‐emitting polymer light‐ emitting diodes (PLEDs) are studied. The PLED investigated has a single emissive layer consisting of a copolymer in which a green and red dye are incorporated in a blue backbone. From single‐carrier devices the effect of the green‐ and red‐emitting dyes on the hole and electron transport is determined. The red dye acts as a deep electron trap thereby strongly reducing the electron transport. By incorporating trap‐assisted recombination for the red emission and bimolecular Langevin recombination for the blue emission, the current and light output of the white PLED can be consistently described. The color shift of single‐layer white‐emitting PLEDs can be explained by the different voltage dependencies of trap‐assisted and bimolecular recombination.     

White‐Light‐Emitting Diodes Based on Iridium Complexes via Efficient Energy Transfer from a Conjugated Polymer

Efficient white‐light‐emitting diodes (WLEDs) have been developed using a polyfluorene‐type blue‐emitting conjugated polymer doped with green and red phosphorescent dyes. The emission spectrum of the conjugated polymer, which has a very high luminescent efficiency, shows a large spectral overlap with the absorbance of green and red iridium complexes. Also, efficient energy transfer from the conjugated polymer to the iridium complexes is observed. Poly(N‐vinyl carbazole) is used to improve the miscibility between conjugated polymer and iridium complexes because of their poor chemical compatibility and phase separation. A white emission spectrum is easily obtained by varying the contents of the three materials and controlling the phase morphology. Moreover, these WLEDs show a voltage‐independent electroluminescence owing to the threshold and driving voltage of the three materials being similar as a result of energy transfer.     

High‐Throughput Combinatorial Optimizations of Perovskite Light‐Emitting Diodes Based on All‐Vacuum Deposition

Light‐emitting diodes (LEDs) based on lead halide perovskites demonstrate outstanding optoelectronic properties and are strong competitors for display and lighting applications. While previous halide perovskite LEDs are mainly produced via solution processing, here an all‐vacuum processing method is employed to construct CsPbBr₃ LEDs because vacuum processing exhibits high reliability and easy integration with existing OLED facilities for mass production. The high‐throughput combinatorial strategies are further adopted to study perovskite composition, annealing temperature, and functional layer thickness, thus significantly speeding up the optimization process. The best rigid device shows a current efficiency (CE) of 4.8 cd A^?1 (EQE of 1.45%) at 2358 cd m^?2, and best flexible device shows a CE of 4.16 cd A^?1 (EQE of 1.37%) at 2012 cd m^?2 with good bending tolerance. Moreover, by choosing NiO_x as the hole‐injection layer, the CE is improved to 10.15 cd A^?1 and EQE is improved to a record of 3.26% for perovskite LEDs produced by vacuum deposition. The time efficient combinatorial approaches can also be applied to optimize other perovskite LEDs.     

Self‐Doping Cathode Interfacial Material Simultaneously Enabling High Electron Mobility and Powerful Work Function Tunability for High‐Efficiency All‐Solution‐Processed Polymer Light‐Emitting Diodes

A variety of N ‐hydrogenated/N ‐methylated pyridinium salts are elaborately designed and synthesized. Thermogravimetric and X‐ray photoelectron spectra analysis indicate the intensities of the N? H covalent bonds are strengthened step‐by‐step from 3,3′‐(5′‐(3‐(pyridin‐3‐yl)phenyl)‐[1,1′:3′,1″‐terphenyl]‐3,3″‐diyl)dipyridine (Tm)‐HCl to Tm‐HBr and then Tm‐TfOH, which results in gradually improved cathode interfacial modification abilities. The larger dipole moments of N⁺? H containing moieties compared to those of the N⁺? CH₃ endow them with more preferable interfacial modification abilities. Electron paramagnetic resonance signals reveal the existence of radical anions in the solid state of Tm‐TfOH, which enables its self‐doping property and high electron mobility up to 1.67 × 10^?3 cm² V^?1 s^?1. Using the Tm‐TfOH as the cathode interfacial layers (CILs), the phenyl‐substituted poly(para ‐phenylene vinylene)‐based all‐solution‐processed polymer light‐emitting diodes (PLEDs) achieve more preferable device performances than the poly[(9,9‐bis(3′‐(N ,N ‐dimethylamino)propyl)‐2,7‐fluorene)‐alt ‐2,7‐(9,9‐dioctylfluorene)]‐based ones, i.e., high current density of nearly 300 mA cm^?2, very high luminance over 15 000 cd m^?2 at a low bias of 5 V. Remarkably, the thickness of the CILs has little impact on the device performance and high efficiencies are maintained even at thicknesses up to 85 nm, which is barely realized in PLEDs with small‐molecule‐based electron transporting layers.     

Organic Light‐Emitting Diodes: Organic Light‐Emitting Diodes with a White‐Emitting Molecule: Emission Mechanism and Device Characteristics (Adv. Funct. Mater. 4/2011)

The unique and unprecedented electroluminescence behavior of the white‐emitting molecule 3‐(1‐(4‐(4‐(2‐(2‐hydroxyphenyl)‐4,5‐diphenyl‐1H‐imidazol‐1‐yl)phenoxy)phenyl)‐4,5‐diphenyl‐1H‐imidazol‐2‐yl)naphthalen‐2‐ol (W1), fluorescence emission from which is controlled by the excited‐state intramolecular proton transfer (ESIPT) is investigated. W1 is composed of covalently linked blue‐ and yellow‐color emitting ESIPT moieties between which energy transfer is entirely frustrated. It is demonstrated that different emission colors (blue, yellow, and white) can be generated from the identical emitter W1 in organic light‐emitting diode (OLED) devices. Charge trapping mechanism is proposed to explain such a unique color‐tuned emission from W1. Finally, the device structure to create a color‐stable, color reproducible, and simple‐structured white organic light‐emitting diode (WOLED) using W1 is investigated. The maximum luminance efficiency, power efficiency, and luminance of the WOLED were 3.10 cd A^?1, 2.20 lm W^?1, 1 092 cd m^?2, respectively. The WOLED shows white‐light emission with the Commission Internationale de l′Eclairage (CIE) chromaticity coordinates (0.343, 0.291) at a current level of 10 mA cm^?2. The emission color is high stability, with a change of the CIE chromaticity coordinates as small as (0.028, 0.028) when the current level is varied from 10 to 100 mA cm^?2.