Synthesis and characterization of N‐ and O‐alkylated poly[aniline‐co‐N‐(2‐hydroxyethyl) aniline]

Poly[aniline‐co‐N‐(2‐hydroxyethyl) aniline] was synthesized in an aqueous hydrochloric acid medium with a determined feed ratio by chemical oxidative polymerization. This polymer was used as a functional conducting polymer intermediate because of its side‐group reactivity. To synthesize the alkyl‐substituted copolymer, the initial copolymer was reacted with NaH to obtain the N‐ and O‐anionic copolymer after the reaction with octadecyl bromide to prepare the octadecyl‐substituted polymer. The microstructure of the obtained polymers was characterized by Fourier transform infrared spectroscopy, ¹H‐NMR, and X‐ray diffraction. The thermal behavior of the polymers was investigated by thermogravimetric analysis and differential scanning calorimetry. The morphology of obtained copolymers was studied by scanning electron microscopy. The cyclic voltammetry investigation showed the electroactivity of poly [aniline‐co‐N‐(2‐hydroxyethyl) aniline] and N and O‐alkylated poly[aniline‐co‐N‐(2‐hydroxyethyl) aniline]. The conductivities of the polymers were 5 × 10^?5 S/cm for poly[aniline‐co‐N‐(2‐hydroxyethyl) aniline] and 5 ×10^?7 S/cm for the octadecyl‐substituted copolymer. The conductivity measurements were performed with a four‐point probe method. The solubility of the initial copolymer in common organic solvents such as N‐methyl‐2‐pyrrolidone and dimethylformamide was greater than polyaniline. The alkylated copolymer was mainly soluble in nonpolar solvents such as n‐hexane and cyclohexane. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis of copolymer of aniline and pyrrole by inverted emulsion polymerization method for supercapacitor

Copolymer of aniline and pyrrole was synthesized by inverted emulsion polymerization method by oxidizing aniline and pyrrole using benzoyl peroxide in presence of sodium laurylsulphate surfactant and p‐toluenesulphonic acid. Copolymer samples were characterized by infrared, X‐ray diffraction and scanning electron microscopic techniques and compared their properties with the corresponding homopolymers. The optimum reaction conditions for the preparation of copolymer with reasonably good yield (1.72 g) and conductivity (7.3 × 10^?2 S/cm) were established. The synthesis procedure was extended to prepare copolymer samples using various protonic acids. Electrochemical characterization such as cyclic voltammetry, charge‐discharge and impedance were carried out on symmetrical supercapacitor cell consists of poly(aniline‐co‐pyrrole)‐p‐toluenesulfonic acid salt, wherein, the copolymer salt was synthesized using equal amount of aniline and pyrrole monomers. The values of specific capacitance, energy and power densities for poly(aniline‐co‐pyrrole)‐p‐toluenesulfonic acid system (PANI‐PPy) were calculated from charge‐discharge studies and are found to be 21 F/g, 5.7 Wh/Kg and 100 W/Kg respectively. Impedance analysis showed specific capacitance value (57 F/g) at 0.01 Hz at 0.22 V. Among the copolymer salts, copolymer prepared with sulfuric acid showed higher capacitance (66 F/g). © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis,characterization, and comparison of self‐doped,doped, and undoped forms of polyaniline,poly(o‐anisidine), and poly[aniline‐co‐(o‐anisidine)]

Polyaniline (PANI), poly(o‐anisidine), and poly[aniline‐co‐(o‐anisidine)] were synthesized by chemical oxidative polymerization with ammonium persulfate as an oxidizing reagent in an HCl medium. The viscosities, electrical conductivity, and crystallinity of the resulting polymers (self‐doped forms) were compared with those of the doped and undoped forms. The self‐doped, doped, and undoped forms of these polymers were characterized with infrared spectroscopy, ultraviolet–visible spectroscopy, and a four‐point‐probe conductivity method. X‐ray diffraction characterization revealed the crystalline nature of the polymers. The observed decrease in the conductivity of the copolymer and poly(o‐anisidine) with respect to PANI was attributed to the incorporation of the methoxy moieties into the PANI chain. The homopolymers attained conductivity in the range of 3.97 × 10^?3 to 7.8 S/cm after doping with HCl. The conductivity of the undoped forms of the poly[aniline‐co‐(o‐anisidine)] and poly(o‐anisidine) was observed to be lower than 10^?5 J/S cm^?1. The conductivity of the studied polymer forms decreased by the doping process in the following order: self‐doped → doped → undoped. The conductivity of the studied polymers decreased by the monomer species in the following order: PANI → poly[aniline‐co‐(o‐anisidine)] → poly(o‐anisidine). All the polymer samples were largely amorphous, but with the attachment of the pendant groups of anisidine to the polymer system, the crystallinity region increased. The undoped form of poly[aniline‐co‐(o‐anisidine)] had good solubility in common organic solvents, whereas doped poly[aniline‐co‐(o‐anisidine)] was moderately crystalline and exhibited higher conductivity than the anisidine homopolymer. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Electrochemical synthesis of poly(2‐iodoaniline) and poly(aniline‐co‐2‐iodoaniline) in acetonitrile

Poly(2‐iodoaniline) (PIANI) and poly(aniline‐co‐2‐iodoaniline) [P(An‐co‐2‐IAn)] were synthesized by electrochemical methods in acetonitrile solution containing tetrabutylammonium perchlorate (TBAP) and perchloric acid (HClO₄). The voltametry of the copolymer shows characteristics similar to those of conventional polyaniline (PANI), and it exhibits higher dry electrical conductivity than PIANI and lower than PANI. The observed decrease in the conductivity of the copolymer relative to PANI is attributed to the incorporation of the iodine moieties into the PANI chain. The structure and properties of these conducting films were characterized by FTIR and UV‐Vis spectroscopy and by an electrochemical method (cyclic voltametry). Conductivity values, FTIR and UV‐Vis spectra of the PIANI and copolymer were compared with those of PANI and the relative solubility of the PIANI and the copolymer powders was determined in various organic solvents. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1652–1658, 2003     

Controllable synthesis and characterization of poly(aniline‐co‐pyrrole) using anionic spherical polyelectrolyte brushes as dopant and template

A poly(aniline‐co‐pyrrole), using anionic spherical polyelectrolyte brushes (ASPB) as dopant and template, was synthesized by chemical oxidation polymerization. The composites were characterized by scanning electron microscopy (SEM), Fourier‐transform infrared spectrometry (FTIR), X‐ray diffraction (XRD), and electrical studies. The SEM images confirmed that the composites had a spherical‐like structure, with a size of ca. 170 nm. The FTIR spectra showed the intermolecular interaction between poly(aniline‐co‐pyrrole) and ASPB. The XRD analysis revealed that the interplanar distance of the copolymers increased from 0.373 nm to 0.391 nm. The electrical conductivity of the poly(aniline‐co‐pyrrole)/ASPB nanocomposites at room temperature was 8.3 S cm⁻¹, higher than that of the conducting copolymers (2.1 S cm⁻¹). These conductive nanocomposites have nanoparticle size, controllable morphology, and the potential for application in inkjet electronic printing. POLYM. COMPOS., 35:1858–1863, 2014. © 2014 Society of Plastics Engineers     

Synthesis of poly(aniline‐co‐o‐toluidine) coatings and their corrosion‐protection performance on low‐carbon steel

Strongly adherent poly(aniline‐co‐o‐toluidine) coatings were synthesized on low‐carbon‐steel substrates by the electrochemical copolymerization of aniline with o‐toluidine with sodium tartrate as the supporting electrolyte. These coatings were characterized with cyclic voltammetry, ultraviolet–visible absorption spectroscopy, Fourier transform infrared spectroscopy, nuclear magnetic resonance spectroscopy, and scanning electron microscopy. The formation of the copolymer with the mixture of monomers in the aqueous sodium tartrate solution was ascertained by a critical comparison of the results obtained from the polymerizations of the individual monomers, aniline and o‐toluidine. The optical absorption spectrum of the copolymer was drastically different from the spectra of the respective homopolymers, polyaniline and poly(o‐toluidine). The extent of the corrosion protection offered by poly(aniline‐co‐o‐toluidine) coatings to low‐carbon steel was investigated in aqueous 3% NaCl solutions by open‐circuit‐potential measurements and a potentiodynamic polarization technique. The results of the potentiodynamic polarization measurements showed that the poly(aniline‐co‐o‐toluidine) coatings provided more effective corrosion protection to low‐carbon steel than the respective homopolymers. The corrosion rate depended on the feed ratio of o‐toluidine used for the synthesis of the copolymer coatings. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103:1868–1878, 2007     

Synthesis of poly[(2‐oxo‐1,3‐dioxolan‐4‐yl)methyl vinyl ether‐co‐N‐phenylmaleimide] and its miscibility in blends with styrene‐acrylonitrile or poly(vinyl chloride)

The aim of the study was to investigate the synthesis of a copolymer bearing cyclic carbonate and its miscibility with styrene/acrylonitrile copolymer (SAN) or poly(vinyl chloride) (PVC). (2‐Oxo‐1,3‐dioxolan‐4‐yl)methyl vinyl ether (OVE) as a monomer was synthesized from glycidyl vinyl ether and CO₂ using quaternary ammonium chloride salts as catalysts. The highest reaction rate was observed when tetraoctylammonium chloride (TOAC) was used as a catalyst. Even at the atmospheric pressure of CO₂, the yield of OVE using TOAC was above 80% after 6 h of reaction at 80°C. The copolymer of OVE and N‐phenylmaleimide (NPM) was prepared by radical copolymerization and was characterized by FTIR and ¹H‐NMR spectroscopies and differential scanning calorimetry (DSC). The monomer reactivity ratios were given as r₁ (OVE) = 0.53–0.57 and r₂ (NPM) = 2.23–2.24 in the copolymerization of OVE and NPM. The films of poly(OVE‐co‐NPM)/SAN and poly(OVE‐co‐NPM)/PVC blends were cast from N‐dimethylformamide. An optical clarity test and DSC analysis showed that poly(OVE‐co‐NPM)/SAN and poly(OVE‐co‐NPM)/PVC blends were both miscible over the whole composition range. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1809–1815, 2000     

Anthranilic acid assisted preparation of Fe3O4–poly(aniline‐co‐o‐anthranilic acid) nanoparticles

Magnetic Fe₃O₄–poly(aniline‐co‐o‐anthranilic acid) nanoparticles were prepared by a novel and simple method: anthranilic acid assisted polymerization. The synthetic strategy involved two steps. First, Fe₃O₄ nanoparticles capped by anthranilic acid were obtained by a chemical precipitation method, and then the aniline and oxidant were added to the modified Fe₃O₄ nanoparticles to prepare well‐dispersed Fe₃O₄–poly(aniline‐co‐o‐anthranilic acid) nanoparticles. Fe₃O₄–poly(aniline‐co‐o‐anthranilic acid) nanoparticles exhibited a superparamagnetic behavior (i.e., no hysteresis loop) and high‐saturated magnetization (M_s = 21.5 emu/g). The structure of the composite was characterized by Fourier‐transform infrared spectra, X‐ray powder diffraction patterns, and transmission electron microscopy, which proved that the Fe₃O₄–poly(aniline‐co‐o‐anthranilic acid) nanoparticles were about 20 nm. Moreover, the thermal properties of the composite were evaluated by thermogravimetric analysis, and it showed excellent thermal stability. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1666–1671, 2006     

Synthesis and characterization of a copolymer: Poly(aniline‐co‐fluoroaniline)

In the present article, we report the chemical synthesis and characterization of poly(aniline‐co‐fluoroaniline) [poly(An‐FAn)]. The copolymerization of aniline and 2‐fluoroaniline was carried out by chemical method in acidic medium. The characterization of poly(aniline‐co‐fluoroaniline) was done using FTIR, UV‐visible spectroscopy, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), scanning electron micrography (SEM), and a four‐points‐probe conductivity method. X‐ray diffraction (XRD) and SEM characterization reveal crystalline nature of doped copolymer compared to undoped copolymer. The observed decrease in the conductivity of the copolymer relative to polyaniline is attributed to the incorporation of the fluoro moieties into the polyaniline chain. The chemically synthesized copolymer shows good solubility in common organic solvents, and is, therefore, technological useful. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 1460–1466, 2001     

Synthesis,properties and thermal stability of water‐soluble poly(potassium 1‐hydroxyacrylate‐co‐styrene) copolymer

The present work investigates the structure properties of copolymers using thermogravimetric analysis, hot stage microscopy, static light scattering, field emission scanning electron microscopy, X‐ray diffraction analysis and a Brookfield viscometer. Poly(potassium 1‐hydroxyacrylate) (PKHA) is a water‐soluble polymer. However, the copolymer of styrene and 2‐isopropyl‐5‐methylene‐1,3‐dioxolan‐4‐one is not water soluble at equal molar ratio because the polystyrene reduces the solubility. The effect of styrene on poly(potassium 1‐hydroxyacrylate‐co‐styrene) copolymer, i.e. poly(KHA‐co‐St), was investigated for the increasing solubility of the copolymer. The solubility was increased at a lower molar ratio of styrene such as 0.4 in the copolymer. It was found that the copolymer was soluble in water when a content ratio of 68/32 mol% of homopolymer was incorporated in poly(KHA₆₈‐co‐St₃₂) copolymer as determined by NMR analysis. Also the poly(KHA₆₈‐co‐St₃₂) copolymer was found to be salt tolerant, possessed water absorption capacity and was thermally stable up to 183 °C. Moreover, it is shown that the polystyrene content plays a key role in the thermal stability of the copolymer. © 2017 Society of Chemical Industry     

Electrochemical preparation of poly(2‐bromoaniline) and poly(aniline‐co‐2‐bromoaniline) in acetonitrile

Electrochemical preparation of poly(2‐bromoaniline) (PBrANI) and poly(aniline‐co‐2‐bromoaniline) [P(An‐co‐2‐BrAn)] was carried out in an acetonitrile solution containing tetrabutylammonium perchlorate (TBAP) and perchloric acid (HClO₄). The cyclic voltammograms during the copolymerization had many features similar to those for the usual polymerization of aniline. The copolymer exhibits a higher dry electrical conductivity value than that of PBrANI and a lower one than that of PANI. The observed decrease in the conductivity of the copolymer relative to PANI is attributed to the incorporation of bromine moieties into the polyaniline chain. The structure and properties of the polymer and copolymer were elucidated using cyclic voltammetry (CV), FTIR, and UV‐vis spectroscopy. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2460–2468, 2003     

Synthesis and characterization of conducting poly(aniline‐co‐diaminodiphenylsulfone) copolymers

Polyaniline, poly(aniline‐co‐4,4′‐diaminodiphenylsulfone), and poly(4,4′‐diaminodiphenylsulfone) were synthesized by ammonium peroxydisulfate oxidation and characterized by a number of techniques, including infrared spectroscopy, ultraviolet–visible absorption spectroscopy, ¹H‐NMR, thermogravimetric analysis, and differential scanning calorimetry. These copolymers had enhanced solubility in common organic solvents in comparison with polyaniline. The conductivities of the HCl‐doped polymers ranged from 1 S cm^?1 for polyaniline to 10^?8 S cm^?1 for poly(4,4′‐diaminodiphenylsulfone). The copolymer compositions showed that block copolymers of 4,4′‐diaminodiphenylsulfone (r₁ > 1) and aniline (r₂ < 1) formed and that the reactivity of 4,4′‐diaminodiphenylsulfone was greater than that of aniline. The results were explained by the effect of the ? SO₂? group present in the polymer structure. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2337–2347, 2003     

Synthesis and characterization of conducting copolymer of Trans‐1‐(4‐methyl‐3′‐thienyl)‐2‐(ferrocenyl)ethene with EDOT

Ferrocene‐substituted conducting polymer namely poly(trans‐1‐(4‐methyl‐3′‐thienyl)‐2‐(ferrocenyl)ethene‐co‐3,4‐ethylenedioxythiophene) [P(MTFE‐co‐EDOT)] was synthesized and its electrochromic properties were studied. Monomer, MTFE, was obtained using 2‐(ferrocenyl)ethene and 3‐methyl‐4‐bromothiophene. The structure of monomer was determined via Fourier transform infrared spectroscopy (FTIR), ¹H‐NMR, and ¹³C‐NMR techniques. The copolymer was synthesized using this monomer and EDOT. The resulting copolymer P(MTFE‐co‐EDOT) was characterized by cyclic voltammetry, FTIR, scanning electron microscopy, atomic force microscopy, and UV–vis spectroscopy. The conductivity measurements of copolymer and PEDOT were accomplished by the four‐probe technique. Although poly(trans‐1‐(4‐methyl‐3′‐thienyl)‐2‐(ferrocenyl)ethene) [P(MTFE)] reveals no electrochromic activity, its copolymer with EDOT has two different colors (violet and gray). Band gap (E_g) and λ_max of P(MTFE‐co‐EDOT) were determined. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis and characterization of poly(HEMA‐co‐MMA)‐g‐POSS nanocomposites by combination of reversible addition fragmentation chain transfer polymerization and click chemistry

New hybrid poly(hydroxyethyl methacrylate‐co‐methyl methacrylate)‐g‐polyhedral oligosilsesquioxane [poly(HEMA‐co‐MMA)‐g‐POSS] nanocomposites were synthesized by the combination of reversible addition fragmentation chain transfer (RAFT) polymerization and click chemistry using a grafting to protocol. Initially, the random copolymer poly(HEMA‐co‐MMA) was prepared by RAFT polymerization of HEMA and MMA. Alkynyl side groups were introduced onto the polymeric backbones by esterification reaction between 4‐pentynoic acid and the hydroxyl groups on poly(HEMA‐co‐MMA). Azide‐substituted POSS (POSS? N₃) was prepared by the reaction of chloropropyl‐heptaisobutyl‐substituted POSS with NaN₃. The click reaction of poly(HEMA‐co‐MMA)‐alkyne and POSS? N₃ using CuBr/PMDEATA as a catalyst afforded poly(HEMA‐co‐MMA)‐g‐POSS. The structure of the organic/inorganic hybrid material was investigated by Fourier transformed infrared, ¹H‐NMR, and ²⁹Si‐NMR. The elemental mapping analysis of the hybrid using X‐ray photoelectron spectroscopy and EDX also suggest the formation of poly(HEMA‐co‐MMA)‐anchored POSS nanocomposites. The XRD spectrum of the nanocomposites gives evidence that the incorporation of POSS moiety leads to a hybrid physical structure. The morphological feature of the hybrid nanocomposites as captured by field emission scanning electron microscopy and transmission electron microscopic analyses indicate that a thick layer of polymer brushes was immobilized on the POSS cubic nanostructures. The gel permeation chromatography analysis of poly(HEMA‐co‐MMA) and poly(HEMA‐co‐MMA)‐g‐POSS further suggests the preparation of nanocomposites by the combination of RAFT and click chemistry. The thermogravimetric analysis revealed that the thermal property of the poly(HEMA‐co‐MMA) copolymer was significantly improved by the inclusion of POSS in the copolymer matrix. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Synthesis and characterization of a ferrocene‐modified,polyaniline‐like conducting polymer

A novel monomer called 1,1′‐ferrocenediacyl anilide (FcA) was synthesized from ferrocene (Fc). Copolymerization was carried out between FcA and aniline (ANI) by an electrochemical method. The novel monomer and copolymer were characterized with ¹H‐NMR, Fourier transform infrared (FTIR) spectroscopy, and ultraviolet–visible (UV–vis) spectroscopy. The hydrogen protons of the benzene ring were moved to a low field in ¹H‐NMR, and the absorption band of N?Q?N (where Q is the quinoid ring) appeared in the FTIR spectrum of the polymer. The peaks of both Fc and the π–π* electronic transition in the UV–vis spectra were redshifted. The results indicate that the copolymer mainly existed as a highly delocalized conjugated system. X‐ray diffraction analysis established further proof, and the process of electrochemical deposition was observed by scanning electron microscopy. The optimal synthesis conditions of the copolymer were determined through changes in the monomer molar ratios and the scan rate. The ideal performance of the copolymer was gained when the monomer molar ratio between FcA and ANI was 1:4 and the scan rate was 50 mV/s. Furthermore, the electrochemical performances were tested in detail by cyclic voltammetry, galvanostatic charge–discharge testing, and electrochemical impedance spectroscopy. The results show that the specific capacitance of poly(1,1′‐ferrocenediacyl anilide‐co‐aniline) increased up to 433.1 F/g at 0.5 A/g, the diffusion resistance was very small, and the durability was good enough. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43217.     

Towards enhanced electrochemical capacitance with self‐assembled synthesis of poly(pyrrole‐co‐o‐toluidine) nanoparticles

Poly(pyrrole‐co‐o‐toluidine) (PPOT) nanoparticles for electrochemical capacitors are easily and productively synthesized by a chemical oxidative polymerization of pyrrole (PY) and o‐toluidine (OT) in 0.5M HCl without any external additive. The polymerization yield, electrical conductivity, and size of the copolymer nanoparticles can significantly be optimized by the oxidant/monomer molar ratio and polymerization temperature. The chemical structure of the obtained copolymer is characterized by UV–vis and FTIR. The copolymer nanoparticles synthesized at 10°C are found to generally have irregular granular morphology with a diameter of 60–100 nm and a small polydispersity index of 1.06 by laser particle‐size analyzer, FE‐SEM, and TEM, and good dispersibility in water. The formation mechanism of the nanoparticles is proposed based on the powerful amphipathicity from comonomer aggregate formed by PY and OT in the monomer solution. The PPOT nanoparticles possess a specific capacitance of 310 F g^?1 at 25 mV s^?1 as well as retain 81% of the initial specific capacitance value after 1000 cycles, while its energy density and power density are found to be 40.2 and 1196 W Kg^?1 at 2 A g^?1. The enhanced electrochemical properties can be attributed to the nanostructural advantage of the PPOT. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42995.     

Synthesis and characterization of novel core‐shell magnetic nanogels based on 2‐acrylamido‐2‐methylpropane sulfonic acid in aqueous media

Ultrafine well‐dispersed Fe₃O₄ magnetic nanoparticles were directly prepared in aqueous solution using controlled coprecipitation method. The synthesis of Fe₃O₄/poly (2‐acrylamido‐2‐methylpropane sulfonic acid) (PAMPS), Fe₃O₄/poly (acrylamide‐co‐2‐acrylamido‐2‐methylpropane sulfonic acid) poly(AM‐co‐AMPS) and Fe₃O₄/poly (acrylic acid‐co‐2‐acrylamido‐2‐methylpropane sulfonic acid) poly(AA‐co‐AMPS) ‐core/shell nanogels are reported. The nanogels were prepared via crosslinking copolymerization of 2‐acrylamido‐2‐methylpropane sulfonic acid, acrylamide and acrylic acid monomers in the presence of Fe₃O₄ nanoparticles, N,N′‐methylenebisacrylamide (MBA) as a crosslinker, N,N,N′,N′‐tetramethylethylenediamine (TEMED) and potassium peroxydisulfate (KPS) as redox initiator system. The results of FTIR and ¹H‐NMR spectra indicated that the compositions of the prepared nanogels are consistent with the designed structure. X‐ray powder diffraction (XRD) and transmission electron microscope (TEM) measurements were used to determine the size of both magnetite and stabilized polymer coated magnetite nanoparticles. The data showed that the mean particle size of synthesized magnetite (Fe₃O₄) nanoparticles was about 10 nm. The diameter of the stabilized polymer coated Fe₃O₄ nanogels ranged from 50 to 250 nm based on polymer type. TEM micrographs proved that nanogels possess the spherical morphology before and after swelling. These nanogels exhibited pH‐induced phase transition due to protonation of AMPS copolymer chains. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Preparation and application of sulfonated poly(1‐octene‐co‐styrene)

In this article, 1‐octene and styrene was copolymerized by the supported catalyst (TiCl₄/ID/MgCl₂). Subsequently, by sulfonation reaction, sulfonated poly(1‐octene‐co‐styrene)s which were amphiphilic copolymers were prepared. The copolymerization behavior between 1‐octene and styrene is moderate ideal behavior. Copolymers prepared by this catalyst contain appreciable amounts of both 1‐octene and styrene. Increase in the feed ratio of styrene/1‐octene leads to increase in styrene content in copolymer and decrease in molecular weight. As the polymerization temperature increases, the styrene content in the copolymers increases, however, the molecular weight decreases. Hydrogen is an efficient regulator to lower the molecular weights of poly(1‐octene‐co‐styrene)s. The sulfonation degree of the sulfonated poly(1‐octene‐co‐styrene)s increased as the styrene content in copolymer increased or the molecular weight decreased. Thirty‐six hour is long enough for sulfonation reaction. The sulfonated poly(1‐octene‐co‐styrene)s can be used as effective and durable modifying agent to improve the wettability of polyethylene film and have potential application in emulsified fuels and for the stabilization of dispersions. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preparation of electrorheological active ionomers from poly(2‐hydroxyethyl methacrylate)‐co‐poly(4‐vinyl pyridine)

In this study, synthesis, characterization, partial hydrolysis, and salt formation of poly(2‐hydroxyethyl methacrylate)‐co‐poly(4‐vinyl pyridine), (poly(HEMA)‐co‐poly‐(4‐VP)) copolymers were investigated. The copolymers were synthesized by free radical polymerization using K₂S₂O₈ as an initiator. By varying the monomer/initiator ratio, chain lengths of the copolymers were changed. The copolymers were characterized by gel permeation chromatography (GPC), viscosity measurements, ¹H and ¹³C NMR and FTIR spectroscopies, elemental analysis, and end group analysis methods. The copolymers were partially hydrolyzed by p‐toluene sulfonic acid monohydrate (PTSA·H₂O) and washed with LiOH_(aq) solution to prepare electrorheological (ER) active ionomers, poly(Li‐HEMA)‐co‐poly(4‐VP). © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99: 3540–3548, 2006     

New synthesis methods for polypropylene‐co‐ethylene‐propylene rubber

In this research, the reinforcement of polypropylene (PP) was studied using a new method that is more practical for synthesizing polypropylene‐block‐poly(ethylene‐propylene) copolymer (PP‐co‐EP), which can be used as a rubber toughening agent. This copolymer (PP‐co‐EP) could be synthesized by varying the feed condition and changing the feed gas in the batch reactor system using Ziegler–Natta catalysts system at a copolymerization temperature of 10°C. The ¹³C‐NMR tested by a 21.61‐ppm resonance peak indicated the incorporation of ethylene to propylene chains that could build up the microstructure of the block copolymer chain. Differential scanning calorimetry (DSC), scanning electron microscopy (SEM), and dynamic mechanical analysis (DMA) results also confirmed these conclusions. Under these conditions, the morphology of copolymer trapped in PP matrix could be observed and the copolymer T_g would decrease when the amount of PP‐co‐EP was increased. DMA study also showed that PP‐co‐EP is good for the polypropylene reinforcement at low temperature. Moreover, the PP‐co‐EP content has an effect on the crystallinity and morphology of polymer blend, i.e., the crystallinity of polymer decreased when the PP‐co‐EP content increased, but tougher mechanical properties at low temperature were observed. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3609–3616, 2007