Analysis of electrical,dielectric, and electromagnetic interference shielding behavior of graphite filled high density polyethylene composites

Conducting polymer composites were prepared by hot compression molding of high‐density polyethylene (HDPE) prelocalized with graphite (Gr). The variation of room temperature electrical conductivity, dielectric constant, and Shore‐D hardness as a function of graphite content were studied below and above percolation threshold. The percolation threshold at which insulator‐conductor transition takes place is estimated to be 0.029 volume fraction of graphite. The observed increase in dielectric constant with addition of graphite also found to be percolative in nature. Above percolation threshold, the dielectric constant is found to decrease sharply with increase in frequency. Electromagnetic shielding effectiveness of HDPE/Gr composites was evaluated in the X‐band frequency range. The composites were found to possess both positive and negative temperature coefficient of resistance. Reproducibility of electrical resistivity with temperature was observed only below the processing temperature. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Electrical conductivity and electromagnetic interference shielding effectiveness of carbon black/sisal fiber/polyamide/polypropylene composites

The effects of hybrid fillers on the electrical conductivity and electromagnetic interference (EMI) shielding effectiveness (SE) of polyamide 6 (PA6)/polypropylene (PP) immiscible polymer blends were investigated. Carbon black (CB) and steam exploded sisal fiber (SF) were used as fillers. CB was coated on the surface of SF, and this was exploded by water steam to form carbon black modified sisal fiber (CBMSF). CB/SF/PA6/PP composites were prepared by melt compounding, and its electromagnetic SE was tested in low‐frequency and high‐frequency ranges. We observed that SF greatly contributed to the effective decrease in the percolation threshold of CB in the PA6/PP matrix and adsorbed carbon particles to form a conductive network. Furthermore, an appropriate CB/SF ratio was important for achieving the best shielding performance. The results indicate that CBMSF was suitable for use as electronic conductive fillers and the CB/SF/PA6/PP composites could be used for the purpose of EMI shielding. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42801.     

Dielectric property and electromagnetic interference shielding effectiveness of ethylene vinyl acetate‐based conductive composites: Effect of different type of carbon fillers

Carbon black, short carbon fiber (SCF), and multiwall carbon nano‐tube (MWNT)‐filled conductive composites were prepared from ethylene vinyl acetate copolymer. The dielectric property and electromagnetic interference (EMI) shielding of carbon black, MWNT, and SCF‐filled composites were studied with different filler loadings. The dielectric constant and loss of filled polymer composites is due to the formation of interfacial polarization in the polymer matrix. It was found that the dielectric constant, dielectric loss, and EMI shielding of filled composites depends on amount and type of filler loading. The results of different experiments have been discussed in the light of break down and formation of continuous conductive network in polymer matrix. The results indicate that these composites can be used as effective EMI shielding materials. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers.     

Electrical,rheological and electromagnetic interference shielding properties of thermoplastic polyurethane/carbon nanotube composites

Electrically conducting rubbery composites based on thermoplastic polyurethane (TPU) and carbon nanotubes (CNTs) were prepared through melt blending using a torque rheometer equipped with a mixing chamber. The electrical conductivity, morphology, rheological properties and electromagnetic interference shielding effectiveness (EMI SE) of the TPU/CNT composites were evaluated and also compared with those of carbon black (CB)‐filled TPU composites prepared under the same processing conditions. For both polymer systems, the insulator–conductor transition was very sharp and the electrical percolation threshold at room temperature was at CNT and CB contents of about 1.0 and 1.7 wt%, respectively. The EMI SE over the X‐band frequency range (8–12 GHz) for TPU/CNT and TPU/CB composites was investigated as a function of filler content. EMI SE and electrical conductivity increased with increasing amount of conductive filler, due to the formation of conductive pathways in the TPU matrix. TPU/CNT composites displayed higher electrical conductivity and EMI SE than TPU/CB composites with similar conductive filler content. EMI SE values found for TPU/CNT and TPU/CB composites containing 10 and 15 wt% conductive fillers, respectively, were in the range ?22 to ?20 dB, indicating that these composites are promising candidates for shielding applications. © 2013 Society of Chemical Industry     

Study of structural,electrical, and dielectric properties of polystyrene/foliated graphite nanocomposite developed via in situ polymerization

Present article reports the investigations of the electrical and dielectric properties of polystyrene/foliated graphite (PS/FG) nanocomposites. The homogenous embedded structure of FG within the polymer matrix has been confirmed by scanning electron microscopy (SEM). The electrical conductivity of the composite was found to exhibit insulator–conductor transition at a very low percolation threshold of FG. A nonlinear to linear transition in the current–voltage characteristics of the composites was observed when the composite undergoes insulator–conductor transition. The frequency dependence of dielectric constant, dissipation factor, and ac conductivity has also been analyzed using percolation theory. D ‐shore hardness of the nanocomposite was also tested to observe the strength of the composites. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

A review on electrically conductive polypropylene and polyethylene

Conductive plastics are new generation functional materials with potential application in electronics, space and aviation industries. Polypropylene (PP) and polyethylene (PE) being most common, widely available and cheapest thermoplastic, if made conductive, can be revolutionary in the field of engineering thermoplastics. The article deals with the fabrication of electrically conductive PP and PE for electromagnetic interference/radio frequency (EMI/RF) shielding applications and protection against electrostatic discharge (ESD). It reviews different fillers used by researchers to fabricate conductive PP and PE, several factors that affect the electrical conductivity of thermoplastic composites and various processing methods that can be adopted to prepare such composites. It exhaustively covers the preparation of such conductive composites, the processing methods involved therein, and the electrical properties of the end material. Emphasis has been given to comprehend the percolation threshold and means to reduce the latter in order to achieve high electrical conductivity in PP‐ and PE‐based composites at relatively low filler loading. POLYM. COMPOS., 35:900–914, 2014. © 2013 Society of Plastics Engineers     

Effect of a carbon black surface treatment on the microwave properties of poly(ethylene terephthalate)/carbon black composites

A surface treatment was applied to carbon black to improve the electrical and microwave properties of poly(ethylene terephthalate) (PET)-based composites. Three different formamide solutions with 1, 2, and 3 wt % concentrations were prepared to modify the surface chemistry of carbon black. Microwave properties such as the absorption loss, return loss, insertion loss, and dielectric constant were measured in the frequency range of 8–12 GHz (X-band range). Composites containing formamide-treated carbon black exhibited enhancements in the electrical conductivity, electromagnetic interference (EMI) shielding effectiveness, and dielectric constant values when compared to composites with untreated carbon black. In addition, increases in the formamide solution concentration and carbon black content of composites resulted in an increase in the electrical conductivity, EMI shielding effectiveness, and dielectric constant values. The percolation threshold concentration of PET composites shifted from a 3 to 1.5 wt % carbon black composition with the surface treatment. The best EMI shielding effectiveness was around 27 dB, which was obtained with the composite containing 8 wt % carbon black treated with a 3 wt % formamide solution. Moreover, this composition gave the lowest electrical resistivity and the highest dielectric constant among the produced composites. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Modification of sisal fiber by in situ coating steam explosion and electromagnetic interference shielding effectiveness of sisal fiber/PP composites

The technology of steam explosion was adopted to modify sisal fiber (SF) material and two different carbon particles, expanded graphite and conductive carbon black (CCB), were in situ coated on the surface of SF during steam explosion process. The DC conductivity and electromagnetic interference shielding effectiveness (SE) of the modified SF/polypropylene (PP) composites were studied and the measurement of electromagnetic interference (EMI) SE was conducted in two frequency ranges of 400–1,000 MHz and 1–18 GHz. The experimental results showed that this novel coating technology could improve the SE of the modified SF/PP composites significantly, which has a strong dependence on the loadings of the expanded graphite modified sisal fiber (SF‐EG) and conductive carbon black modified sisal fiber (SF‐CCB). When the loadings of SF‐EG and SF‐CCB reached 50 wt%, the maximum values of the SE were 33 dB and 51 dB, respectively. For the modified SF/PP composites, the experimental EMI SE values are in good correlation with the theoretical calculation values in far field of electromagnetic radiation. POLYM. COMPOS., 35:1038–1043, 2014. © 2013 Society of Plastics Engineers     

Graphene nanoplate and multiwall carbon nanotube–embedded polycarbonate hybrid composites: High electromagnetic interference shielding with low percolation threshold

This study has reported the preparation of polycarbonate (PC)/graphene nanoplate (GNP)/multiwall carbon nanotube (MWCNT) hybrid composite by simple melt mixing method of PC with GNP and MWCNT at 330°C above the processing temperature of the PC (processing temperature is 280°C) followed by compression molding. Through optimizing the ratio of (GNP/MWCNT) in the composites, high electromagnetic interference shielding effectiveness (EMI SE) value (∼21.6 dB) was achieved at low (4 wt%) loading of (GNP/MWCNT) and electrical conductivity of ≈6.84 × 10⁻⁵ S.cm⁻¹ was achieved at 0.3 wt% (GNP/MWCNT) loading with low percolation threshold (≈0.072 wt%). The high temperature melt mixing of PC with nanofillers lowers the melt viscosity of the PC that has helped for better dispersion of the GNPs and MWCNTs in the PC matrix and plays a key factor for achieving high EMI shielding value and high electrical conductivity with low percolation threshold than ever reported in PC/MWCNT or PC/graphene composites. With this method, the formation of continuous conducting interconnected GNP‐CNT‐GNP or CNT‐GNP‐CNT network structure in the matrix polymer and strong π–π interaction between the electron rich phenyl rings and oxygen atom of PC chain, GNP, and MWCNT could be possible throughout the composites. POLYM. COMPOS., 37:2058–2069, 2016. © 2015 Society of Plastics Engineers     

Electrical conductivity and electromagnetic interference shielding effectiveness of polyaniline–ethylene vinyl acetate composites

Electrical conductivity and electromagnetic interference (EMI) shielding effectiveness at microwave (200–2000 MHz) and X‐band (8–12 GHz) frequency range of polyaniline (PAni) composites were studied. It has been observed that EMI shielding of conductive polyaniline (PAni)–ethylene vinyl acetate composites increases with the increase in the loading levels of the conductive polymer doped with dodecylbenzene sulfonic acid. The result indicates that the composites having higher PAni loading (>23%) can be used for EMI shielding materials and those with lower PAni loading can be used for the dissipation of electrostatic charge. Copyright © 2004 Society of Chemical Industry     

Influence of carbon‐based nanofillers on the electrical and dielectric properties of ethylene vinyl acetate nanocomposites

A comparative study of ethylene vinyl acetate nanocomposites based on expanded graphite, multiwalled carbon nanotubes, and carbon nanofibers has been carried out to investigate the effect of different carbon nanofillers on the electrical properties of the corresponding composites. The composites were prepared by ultrasonic dispersion of fillers in ethylene vinyl acetate solution, followed by casting and compression molding. The dependence of AC conductivity and dielectric constant on the frequency and filler concentration was investigated. Carbon nanofibers provided maximum conductivity as well as lowest percolation threshold (8.2 vol%) compared to expanded graphite and multiwalled carbon nanotubes filled composites. The improvement in both electrical conductivity and dielectric constant was attributed to the high filler aspect ratio and the formation of conducting networks. The relationship of dielectric constant with filler volume fraction for all the composite systems is estimated using a power law. The pressure sensing capability of the composites at respective percolation thresholds was also compared. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

Effect of percolation on electrical and dielectric properties of acrylonitrile butadiene styrene/graphite composite

Prelocalized Acrylonitrile Butadiene Styrene/graphite composites were prepared by hot compression molding technique. The increased conductivity with increase of graphite content exhibits percolation phenomenon. The current–voltage characteristics are found to change from nonlinear to linear above the percolation threshold. A positive temperature coefficient of resistance is observed in these composites, and this effect is more pronounced in samples having graphite concentration near percolation threshold. The dielectric constant was found to increase slowly up to the percolation concentration and beyond it a sudden increase in its value is observed. The dissipation factor exhibits maxima in the vicinity of percolation threshold. The dielectric properties are discussed in terms of the interfacial Maxwell‐Wagner effects. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Electrical properties of exfoliated-graphite filled polyethylene composites

An experimental study has been carried out to prepare and characterize high density polyethylene-based composites filled with exfoliated graphite particles of varied aspect ratios. It has been demonstrated that the dielectric constant of the composite correlates with the in situ volumetric fraction of the compressible exfoliated filler particles. The dielectric constant has been found to range from 2.23 to 125. The minimum electrical resistivity of the composites obtained was 0.1 Ω.cm at a graphite content of 40 percent by volume. The use of these composites is intended in electromagnetic radiation interference (EMI) shielding.     

Conducting polyaniline composite for ESD and EMI at 101 GHz

Conducting polyaniline forms an important family of electronic polymers with a developed potential application for a number of areas because of their flexible chemistry, processibility, environmental stability and ease of forming composites. The electromagnetic interference shielding effectiveness of conducting polyaniline (PANI)–ABS composites was studied at 101 GHz. It was observed that shielding effectiveness of the PANI–ABS composites increases with the increase in the loading levels of the conducting polymer doped with hybrid dopants. The lower loading of PANI doped with hybrid dopants in the moulded conducting composites can be effectively used for the dissipation of electrostatic charge. However, with higher loadings, a shielding effectiveness of 60 dB has been achieved which makes the conducting composites a potential EMI shielding material for its application in encapsulation of electronic equipments in electronic and in high tech applications.     

Ultra‐high dielectric constant of poly(vinylidene fluoride) composites filled with hydroxyl modified graphite powders

We provide a one‐step hydrothermal reaction to modify graphite powders (GPs) and prepare hydroxyl modified GPs/poly(vinylidene fluoride) (PVDF) composites which have excellent dielectric properties using high conductivity, low cost GPs as raw material. Fourier transform infrared spectroscopy (FT‐IR) and X‐ray photoelectron spectroscopy (XPS) showed that hydroxyl groups had been introduced to the surface of GPs. Scanning electron microscopy (SEM) showed that the hydroxyl modified GPs had better dispersion in the polymer matrix than the GPs. An ultra‐high dielectric constant of more than 5.1 × 10³ (dielectric loss is about 3.0) was obtained for the hydroxyl modified GPs/PVDF near the percolation threshold at 1 kHz. The hydroxyl modified GPs/PVDF composites exhibited better dielectric properties than most carbon/polymer composites. POLYM. COMPOS., 37:327–333, 2016. © 2014 Society of Plastics Engineers     

Facile preparation of light-weight biodegradable and electrically conductive polymer based nanocomposites for superior electromagnetic interference shielding effectiveness

Harmful electromagnetic radiations that are generated from different electronic devices could be absorbed by a light weight and mechanically flexible good electromagnetic interference (EMI) shielding polymer nanocomposite. On the other hand, different electronic wastes (“e-wastes”) which are generally polymer building materials generated from wastes of dysfunctional electronic devices are not naturally biodegradable. Our recent effort has been employed to produce bio-degradable EMI shielding polymer nanocomposite. For that purpose, we had prepared a 50:50 ratio polylactic acid/thermoplastic polyurethane polymer nanocomposite by mixing the conducting carbon black with the blend following the facile and industrially feasible solution mixing method. Morphological characterizations by scanning electron microscopy and transmission electron microscopy analysis revealed the co-continuous morphology of the neat blend as well as polymer nanocomposites with the preferential distribution of conductive filler on a particular polymer phase. The polymer nanocomposites gave good mechanically with improved thermal properties. We got EMI shielding effectiveness around −27 dB with a low percolation threshold at around 30 wt% filler loading in the polymer nanocomposite at the X-band frequency domain (8.2–12.4 GHz). Later we had studied the biodegradability of the PLA/TPU along with their composites (T_XP_XC_X) by employing the respirometry method and got a satisfactory result to ensure their biodegradability.     

Design and fabrication of long‐carbon‐fiber‐reinforced polyamide‐6/nickel powder composites for electromagnetic interference shielding and high mechanical performance

The long‐carbon‐fiber‐reinforced polyamide‐6/nickel powder composites were designed as electromagnetic interference (EMI) shielding materials and then were prepared through the joint processing of melt blending and thermoplastic pultrusion. The obtained composites show high conductivity and permittivity as well as a high dielectric loss with co‐addition of carbon fiber and nickel powders, which makes the resulting composites a higher level of shielding effectiveness due to the combination of conductive and magnetic fillers. The composites are capable of shielding mainly through absorption rather than reflection. On the other hand, the composites achieved significant improvements in tensile, flexural, and impact strength due to the superiority of the long‐carbon‐fiber‐reinforced technique. The residual fiber length in the injection‐molded specimens is greatly superior to the critical one predicted by the Kelly–Tyson model. This takes full advantage of the strength of the reinforcing fiber itself, thus leading to a promising reinforcement effect. The enhancement of impact toughness is due to the energy dissipation by fiber fracture as a result of long fiber effect. The morphologic investigation indicated that the fiber fracture and fiber pullout concurred on the impact and tensile fracture surfaces, and the former preceded the latter. Highlighted with both good EMI shielding properties and excellent mechanical performance, the composites designed by this work exhibit potential applications for the automotive, electronic, aerospace, and military industries. POLYM. COMPOS., 37:2705–2718, 2016. © 2015 Society of Plastics Engineers     

Electrical and mechanical properties of multi‐walled carbon nanotubes reinforced PMMA and PS composites

The use of multi‐walled carbon nanotubes (MWCNT) as reinforcing material for thermoplastic polymer matrices, polymethyl methacrylate (PMMA), and polystyrene (PS) has been studied. MWCNT were synthesized by chemical vapor deposition (CVD) technique using ferrocene‐toluene mixture. As‐prepared nanotubes were ultrasonically dispersed in toluene and subsequently dispersed in PMMA and PS. Thin polymer composite films were fabricated by solvent casting. The effect of nanotube content on the electrical and mechanical properties of the nanocomposites was investigated. An improvement in electrical conductivity from insulating to conducting with increasing MWCNT content was observed. The carbon nanotube network showed a classical percolating network behavior with a low percolation threshold. Electromagnetic interference (EMI) shielding effectiveness value of about 18 dB was obtained in the frequency range 8.0–12 GHz (X‐band), for a 10 vol% CNT loading. An improved composite fabrication process using casting followed by compression molding and use of functionalized MWCNT resulted in increased composites strength. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Fabrication and characterization of NBR/MWCNT composites by latex technology

To develop a rubber composite with excellent electrical properties, a sort of synthetic rubber, acrylonitrile butadiene rubber (NBR) with CN dipoles as matrix, multi‐walled carbon nanotubes (MWCNTs) as filler, was synthesized. NBR composites reinforced with 0.5, 1.5, 3, 10, and 20 phr MWCNT contents were fabricated by latex technology. The electrical conductivity, dielectric characteristics, and electromagnetic interference (EMI) shielding effectiveness at room temperature of NBR/MWCNT composites were investigated. MWCNTs were found well dispersed into NBR matrix even for 20 phr content by FESEM observation. The electrical conductivity increased with an increment of MWCNT content. The dielectric constant was over 10⁴ at 10³ Hz frequency for 10 and 20 phr MWCNTs‐reinforced NBR composites. It was attributed to the increased electrons and interface polarization. The improved conductivity and dielectric permittivity resulted in an enhanced EMI shielding effectiveness. The EMI shielding effectiveness reached 26 dB at 16.7 GHz frequency for NBR/20 phr MWCNT composite with 1.0 mm thickness. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

导电电磁屏蔽塑料研究新进展

介绍了电磁屏蔽的基本理论,重点综述了3类主要的导电塑料即:表层导电型复合塑料、填充型复合塑料和本征导电高分子材料的研究应用现状,介绍了各类导电高分子电磁屏蔽材料的特点,并对其发展趋势做了展望。