Optimization of kinetic data for two‐stage batch adsorption of Pb(II) ions onto tripolyphosphate‐modified kaolinite clay

BACKGROUND: Most adsorption studies consider only the adsorption of pollutants onto low cost adsorbents without considering how equilibrium and kinetic data can be optimized for the proper design of adsorption systems. This study considers the optimization of kinetic data obtained for the removal of Pb(II) from aqueous solution by a tripolyphosphate modified kaolinite clay adsorbent. RESULTS: Modification of kaolinite clay with pentasodium tripolyphosphate increases its cation adsorption capacity (CEC) and specific surface area (SSA) from 7.81 to 78.9 meq (100 g)^?1 and 10.56 to 13.2 m² g^?1 respectively. X‐ray diffraction patterns for both unmodified and tripolyphosphate‐modified kaolinite clay suggest the modification is effective on the surface of the clay mineral. Kinetic data from the batch adsorption of Pb(II) onto the tripolyphosphate‐modified kaolinite clay adsorbent were optimized to a two‐stage batch adsorption of Pb(II) using the pseudo‐second‐order kinetic model. Mathematical model equations were developed to predict the minimum operating time for the adsorption of Pb(II). Results obtained suggest that increasing temperature and decreasing percentage Pb(II) removal by the adsorbent enhanced operating time of the adsorption process. The use of two‐stage batch adsorption reduces contact time to 6.7 min from 300 min in the single‐stage batch adsorption process for the adsorption of 2.5 m³ of 500 mg L^?1 Pb(II) under the same operating conditions. CONCLUSION: Results show the potential of a tripolyphosphate‐modified kaolinite clay for the adsorption of Pb(II) from aqueous solution and the improved efficiency of a two‐stage batch adsorption process for the adsorption of Pb(II) even at increased temperature. Copyright © 2009 Society of Chemical Industry     

Montmorillonite clay nanocomposites based on vinyl pyridine‐styrene‐butadiene terpolymer (VPR)/acrylonitrile‐butadiene rubber (NBR) blend

This study describes a novel route to synthesize vinyl pyridine‐styrene‐butadiene terpolymer rubber (VP rubber) montmorillonite clay nanocomposites by latex blending technique. The pyridine moiety of the VP rubber was modified with methyl iodide to form the pyridinium ion during latex blending. Cation exchange reaction of the pyridinium ion of the VP rubber latex with sodium montmorillonite occurred during latex stage mixing which helped to form VP rubber‐montmorillonite clay nanocomposites. Coagulation of the latex‐clay slurry produced nanocomposites master batch. The master batch was compounded with acrylonitrile butadiene rubber (NBR). Fourier Transform Infrared Spectroscopy (FTIR) confirmed the modification of the pyridine moiety of VP rubber. Wide angle X‐ray diffraction (WAXD), scanning electron microscopy‐energy dispersive X‐ray spectrophotometry (SEM‐EDS) and transmission electron microscopy (TEM) provided the evidences of formation of nanocomposite. Remarkable improvements in the mechanical properties were found by addition of small amount of modified clay. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Sorption studies of neutral red dye onto poly(acrylamide‐co‐maleic acid)‐kaolinite/montmorillonite composites

In this study, a procedure for preparation of organic–inorganic composite was established. The procedure was based on gamma irradiation polymerization of polyacrylamide (PAAm) in presence of maleic acid (MA), clay minerals [kaolinite (K)], or [montmorillonite (M)] and methylenebisacrylamide (NMBA) as a crosslinker. The functionality of the produced adsorbents were assayed using FTIR spectroscopy, SEM, and XRD and were evaluated for sorption of neutral red (NR) dye from aqueous solutions via batch sorption experiments. Various factors influencing the sorption behavior (e.g., pH, sorbent dose, and dye concentration) were studied. The sorption data fitted well with Langmuir isotherm model. Batch kinetic experiments showed that the adsorption followed pseudosecond‐order kinetic model with correlation coefficients greater than 0.999. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Arsenic adsorption on Ti‐pillared montmorillonite

BACKGROUND: Arsenic pollution in drinking water has been found in most countries. Arsenate (As(V)) and arsenite (As(III)) are two major forms of inorganic arsenic species, and the latter is the more toxic. The removal of arsenic ions from water has attracted increased attention, and therefore further understanding and development of techniques for removal of arsenic ions are required. RESULTS: Adsorption of arsenate and arsenite from aqueous solutions using Ti‐pillared montmorillonite (Ti‐MMT) was investigated as a function of contact time, pH, temperature, coexisting ions, and ionic strength. The adsorption of both arsenate and arsenite were temperature and pH dependent, indicating different adsorption mechanisms. The effect of coexisting ions on the adsorption was also studied and, among the ions investigated, only phosphate had a noticeable influence on the adsorption of arsenate, while the effect of other ions was negligible. A pseudo‐second‐order chemical reaction model was obtained for both arsenate and arsenite; adsorption isotherms of arsenate and arsenite fitted the Langmuir and Freundlich isotherm models well. X‐ray diffraction (XRD) and X‐ray photoelectron spectroscopy (XPS) were used to study the nature of surface elements before and after adsorption. CONCLUSIONS: This work demonstrates that Ti‐pillared montmorillonite is an efficient material for the removal of arsenate and arsenite from aqueous solutions. Experimental parameters such as contact time, solution pH, temperature, initial concentration, coexisting ions, and ionic strength have been optimized. Copyright © 2010 Society of Chemical Industry     

Preparation and phenol captivating properties of polyvinylpyrrolidone‐montmorillonite hybrid materials

Montmorillonite minerals were modified in two distinct steps in order to remove hydroxlated toxicants from the aqueous environment. At first, the montmorillonite minerals were acrylated with the silylating agent γ‐methcaryloxypropyl trimethoxysilane to give a product denoted as TAY‐10. In the second step these materials readily reacted with vinylpyrrolidone to form copolymers covalently bonded to the clay. All hybrid materials were characterized by FTIR spectroscopy, thermogravimetry, X‐ray diffractometry, SEM, and differential thermal analysis. The original montmorillonite structure was maintained for the copolymer modified surfaces. Different loadings of polyvinylpyrrolidone (PVP) were examined to arrive at the optimal conditions for the removal of toxicants from the aqueous environment. The presence of the PVP enhanced the adsorption capacity of the clay toward phenolic compounds from solution as evidenced by the retention percent that was as high as 98.9%. These results demonstrated the feasibility of utilizing a PVP modified clay as a thermally recyclable adsorbent for environmental pollutants. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 512–519, 2001     

Kinetic and equilibrium modeling of liquid‐phase adsorption of lead and lead chelates on activated carbons

The sawdust (SD) waste generated in the timber industry was converted to a low‐cost activated carbon (SDAC) using a simpler and cheaper activation process, single‐step steam pyrolysis activation. The possibility of utilizing SDAC for the removal of lead (Pb(II)) in the absence of ligands and nitrilotriacetic acid (NTA) and ethylenediaminetetraacetic acid (EDTA) chelated Pb(II) complexes from the liquid phase was examined and the results were compared with those for commercial activated carbon (CAC). SDAC shows a high adsorption capacity for Pb(II) and Pb(II) chelates compared with CAC. The extent of adsorption of Pb(II) and Pb(II) chelates on activated carbons was found to be a function of solution pH and species distribution of Pb(II) and Pb(II) chelates. The optimum pH range for the removal of Pb(II) in the absence of ligands by SDAC was 6.5–8.0, whereas its maximum removal by CAC was observed at pH 6.5. In the presence of ligands, the extent of Pb(II) adsorption was enhanced in the pH range 2.0–5.0 and was reduced significantly in the pH range 6.0–8.0. The maximum uptake of Pb(II) chelates for both carbons was observed at pH 5.0. Kinetic models such as pseudo‐first‐order, pseudo‐second‐order and pore diffusion were tested to investigate the adsorption mechanism. Batch kinetic studies showed that the adsorption of Pb(II) from aqueous solutions with and without ligands could be best described by a psuedo‐first‐order model for both carbons. The effect of pH on the adsorption isotherms of Pb(II) and Pb(II) chelates was also investigated. The applicability of the Langmuir and Freundlich isotherms, established for various initial concentrations of the adsorbate and for different pH values, was tested at 30 °C. Copyright © 2003 Society of Chemical Industry     

Crystalline forms in melt‐crystallized syndiotactic polystyrene/clay nanocomposites

X‐ray diffraction methods and polarized optical microscopy have been used to investigate the structural change of syndiotactic polystyrene/clay nanocomposites. The nanocomposite has prepared by mixing an sPS polymer solution with organically modified montmorillonite. Both X‐ray diffraction and transmission electron microscopy results indicate that most of the swellable silicate layers are exfoliated and randomly dispersed into the sPS matrix. The X‐ray diffraction data also show the presence of polymorphism in sPS/clay nanocomposites, which is strongly dependent on the thermal history of the nanocomposites from the melt and on the content of clay. In this study, the effect of premelting temperatures and crystallization temperatures of sPS and sPS/clay nanocomposites on their crystalline phases is discussed.     

Functional copolymer/organo‐montmorillonite nanoarchitectures. IX. Synthesis and nanostructure–morphology–thermal behaviour relationships of poly[(maleic anhydride)‐alt‐(acrylic acid)]/organo‐ montmorillonite nanocomposites

Functional copolymer/clay hybrids were synthesized by radical‐initiated interlamellar copolymerization of maleic anhydride/maleic acid and acrylic acid with 2,2′‐azobis(2‐methylpropionamidine) dihydrochloride as a water‐soluble ionizable radical initiator in the presence of reactive (octadecylamine‐montmorillonite (ODA‐MMT)) and non‐reactive (dimethyldodecylammonium‐montmorillonite) organoclays at 60 °C in aqueous medium under nitrogen atmosphere. The monomers were dissolved in aqueous medium, and the two types of clay particles used were easily dissolved and dispersed partially swollen, respectively, in deionized water. Structure, thermal behaviour and morphology of the synthesized nanocomposites were investigated using Fourier transform infrared spectroscopy, X‐ray diffraction, differential scanning calorimetry, thermogravimetric analysis, and scanning and transmission electron microscopy. It is demonstrated that intercalative copolymerization proceeds via ion exchange between organoclays and carboxylic groups of monomers/polymers, which essentially improves interfacial interactions of polymer matrix and clay layers through strong hydrogen bonding. In the case of intercalative copolymerization in the presence of ODA‐MMT clay, a similar improvement is provided by in situ hydrogen bonding and amidolysis of carboxylic/anhydride groups from copolymer chains with primary amine groups of ODA‐MMT. The nanocomposites exhibit higher degree of intercalation/exfoliation of copolymer chains, improved thermal properties and fine dispersed morphology. Copyright © 2011 Society of Chemical Industry     

Uptake of Ni(II) Ions from Aqueous Solution by Kaolinite and Montmorillonite: Influence of Acid Activation of the Clays

Abstract

Kaolinite and montmorillonite were treated with 0.25 M H₂SO₄ and the acid activated clays along with the parent clays were tested for their uptake capacity for Ni(II) ions from aqueous solution. The batch adsorption experiments were conducted under a set of variables (concentration of Ni(II) ion, amount of clay, pH, time and temperature of interaction). Increasing pH favored Ni(II) uptake till the ions were precipitated as the insoluble hydroxides at pH > 8.0. The uptake was rapid up to 40 min and equilibrium was obtained within 180 min. The kinetics of the process was evaluated by subjecting the results to a number of models like the pseudo-first order, second order, Elovich equation, liquid film diffusion, and intra-particle diffusion and it was found that the data more closely resembled a second order process. The experimental data conformed to both Langmuir and Freundlich isotherms showing that the interactions were mostly chemical in nature. The clays had reasonable monolayer adsorption capacity of 10.4, 11.9, 28.4, and 29.5 mg g^?1 for kaolinite, acid activated kaolinite, montmorillonite, and acid-activated montmorillonite respectively. Montmorillonite had much better adsorption capacity than kaolinite and the acid activation boosted the adsorption capacity of both kaolinite and montmorillonite. The interactions were exothermic in nature, accompanied by decrease in both entropy and Gibbs energy. The results have established good potentiality for kaolinite, montmorillonite and their acid-activated forms to take up and separate Ni(II) from aqueous medium through adsorption-mediated immobilization.     

Synthesis and characterization of in situ sodium‐activated and organomodified bentonite clay/styrene–butadiene rubber nanocomposites by a latex blending technique

In this article, we describe a method used to prepare an in situ sodium‐activated, organomodified bentonite clay/styrene–butadiene rubber nanocomposite master batch via a latex blending technique. The clay master batch was used for compound formulation. Octadecyl amine was used as an organic intercalate. The clay was purchased from local suppliers and was very cheap. Sodium chloride was used for in situ activation of the clay. The wide‐angle X‐ray diffraction data indicated that the in situ sodium activation helped to increase the intergallery distance from 1.28 to 1.88 nm. A transmission electron micrograph indicated intercalation and partial exfoliation. The thermal properties were relatively better in the case of the sodium‐activated, organomodified bentonite‐clay‐containing compound. A substantial improvement in physical properties such as the modulus, tensile strength, tear strength, and elongation at break was observed in the case of the in situ sodium‐activated compound. A cation‐exchange capacity equivalent (of the clay) of 1.5 times the octadecyl amine was the optimum dose for the modification. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Preparation and characterization of polystyrene–clay nanocomposites by free‐radical polymerization

The polymerizable cationic surfactant, vinylbenzyldimethylethanolammouium chloride (VBDEAC), was synthesized to functionalize montmorillonite (MMT) clay and used to prepare exfoliated polystyrene–clay nanocomposites. The organophilic MMT was prepared by Na⁺ exchanged montmorillonite and ammonium cations of the VBDEAC in an aqueous medium. Polystyrene–clay nanocomposites were prepared by free‐radical polymerization of the styrene containing intercalated organophilic MMT. Dispersion of the intercalated montmorillonite in the polystyrene matrix determined by X‐ray diffraction reveals that the basal spacing is higher than 17.6 nm. These nanocomposites were characterized by differential scanning calorimetry (DSC), transmission electron micrograph (TEM), thermal gravimetric analysis (TGA), and mechanical properties. The exfoliated nanocomposites have higher thermal stability and better mechanical properties than the pure polystyrene. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1370–1377, 2002     

A study on the preparation of polymer/montmorillonite nano‐composite materials by photo‐polymerization

The preparation of polymer/montmorillonite intercalation composite materials was studied by two kinds of photo‐polymerization reaction (photo‐acid generation and photo‐radical generation). Small‐angle X‐ray diffraction was used for the structural characterization of montmorillonite contained in the products. Results indicated that, after chemical modification of montmorillonite, the monomer (methyl methacrylate) and the prepolymer (m‐cresol/HMMM) were able to intercalate into the layers of clay and to polymerize ‘in situ’, thus producing photo‐polymerized composite materials. The advantages and shortcomings of the method of photo‐polymerization for the preparation of these composite materials are discussed. © 2001 Society of Chemical Industry     

Adsorption of Co(II) from Aqueous Medium on Natural and Acid Activated Kaolinite and Montmorillonite

Abstract

Hazardous metal cations enter water through the natural geochemical route or from the industrial wastes. Their separation and removal can be achieved by adsorptive accumulation of the cations on a suitable adsorbent. In the present work, toxic Co(II) ions are removed from water by accumulating them on the surface of clay minerals. Clay adsorbents are obtained from kaolinite, montmorillonite, and their acid activated forms, and are characterized with the measurement of XRD patterns, specific surface area, and cation exchange capacity. The adsorption experiments are carried out in a batch process in environments of different pH, initial Co(II) concentration, amount of clay, interaction time, and temperature. Adsorption of Co(II) on the clays increases continuously from pH 1.0 to 8.0 after which adsorption could not be carried out due to the decreasing solubility of Co(II). Under appropriate conditions, the adsorption of Co(II) is very fast at low coverage approaching equilibrium within 240 min and the interactions are best described by second order kinetics. Langmuir monolayer capacity has been computed in the range of 11.2 to 29.7 mg/g and Co(II) accumulation has the order of acid‐activated montmorillonite>montmorillonite>acid activated kaolinite>kaolinite. Adsorption of Co(II) on kaolinite and acid‐activated kaolinite is endothermic driven by entropy increase but the same process follows exothermically on montmorillonite and acid‐activated montmorillonite supported by entropy decrease. In both cases, spontaneous adsorptive accumulation is ensured by favorable Gibbs energy decrease. It is found that acid activation enhances the adsorption capacity of kaolinite and montmorillonite.     

Copolymerization of styrene with N‐phenyl maleimide in the presence of montmorillonite

The copolymerization of styrene with N‐phenyl maleimide in the presence of organomodified montmorillonite or Na⁺ montmorillonite was investigated. The conversion of the monomer was determined dilatometrically or gravimetrically. The copolymerization rate was accelerated and the polymerization activation energy in bulk and solution copolymerization decreased in the presence of montmorillonite. The tendency of alter‐copolymerization was enhanced for bulk and solution polymerization, but not affected for emulsion polymerization, by the addition of organomodified montmorillonite or Na⁺ montmorillonite. X‐ray diffraction studies showed that the methods of emulsion and bulk intercalative polymerization were more appropriate techniques for preparing nanocomposites with good dispersibility of clay. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1932–1937, 2005     

Transport Properties of Modified Montmorillonite‐Poly(ε‐caprolactone) Nanocomposites

A series of montmorillonite‐poly(ε‐caprolactone) nanocomposites were prepared according to a two‐stage procedure. In the first step Na‐type silicate clay was cation exchanged with protonated 12‐aminolauric acid. In the second step ε‐caprolactone was intercalated in the modified clay and ring‐opening polymerized. The clay content was varied regularly from 0 to 44 wt.‐%, with exfoliation of the silicate layers being detected by X‐ray diffraction in the nanocomposites dispersing up to at least 16 wt.‐% clay. Crystallization of poly(ε‐caprolactone) was not prevented in the nanocomposites, although it proceeded to a lower extent/order than in a homopolymer sample. The transport properties were investigated using water or dichloromethane as vapor permeants. In each case, a dual sorption behavior was observed as a function of the vapor activity because of the occurrence of different sorption mechanisms. The permeability of the nanocomposites to either permeant decreased with increasing clay content. In particular, the permeability behavior to water was largely dominated by the diffusion parameter.     

Adsorption studies of fatty acids on montmorillonite‐based filler clay

Surface coating of montmorillonite‐based filler clay with stearic and oleic (9‐octadecenoic acid) acids was presented. Sedimentation measurements showed that the sedimentation rate and the sediment volume decreased sharply with the adsorbed amount of the acid up to a certain concentration and then became constant. The chemical analysis showed that the adsorbed amount of either acid by montmorillonite clay increased with the equilibrium concentration of the acid in the solution. The adsorption isotherm indicated the formation of a monolayer on the clay surface at a lower concentration of the acids followed by formation of multilayers of the acids on the clay surfaces at higher concentrations. XRD analysis indicated no intercalation of either acid in the lamella of the clay. We concluded the possibility of surface coating of montmorillonite clay with a monolayer of fatty acids that render the clay organophilic. The adsorption of either acid improved the dispersibility of the clay particles in organic or polymeric media. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2574–2580, 2002     

Starch‐based nanocomposites by reactive extrusion processing

Nanocomposites with unique material properties have been prepared from synthetic plastics and nanosilicates (nanoclay) until now, but not from biopolymers such as starch. The primary challenge in making biopolymeric nanocomposites is to achieve strong adhesion between nanoclay and polymer matrix. For the first time nanocomposites with superior properties have been successfully made from starch‐polycaprolactone (PCL) blends in the presence of montmorillonite (MMT) nanoclay. Reactive extrusion results showed that addition of a modified nanoclay at 3 % wt level increased elongation almost fourfold over that of pristine starch–PCL blends. X‐ray diffractions results showed dispersion of clay in the polymer matrix. The nanocomposites have better solvent‐resistance properties because of resistance to diffusion offered by clay platelets in the polymer matrix. Copyright © 2004 Society of Chemical Industry     

Preliminary evaluation of polymeric Fe‐ and Al‐modified clays as adsorbents for heavy metal removal in water treatment

This paper assesses the potential of modified montmorillonite clays as low‐cost adsorbents/ion‐exchangers for the removal of trace level heavy metals (Cd, Cu, Ni, Pb and Zn) from potable water. Modification of the montmorillonites resulted in the exchange of the interlayer calcium ions for the polymeric species. One unmodified montmorillonite and three polymeric Fe‐ and Al‐modified montmorillonites have been evaluated with respect to their selectivity and uptake performance. All of the clays are selective for Pb and Cu adsorption from aqueous solutions at the mildly acidic pH range in which the experiments were performed (pH 5.5–6). Polymeric iron‐ and polymeric Al/Fe‐modified clays had comparatively great affinities for all the metals studied, whilst the original and polymeric Al modified clays had relatively lower affinities. Only the uptake of Pb and Cu could be correlated with physical properties such as clay surface area. The metal selectivity could be correlated to the type of intercalated polymeric Fe and Al species of the modified clays. © 2002 Society of Chemical Industry     

Comparative studies on corrosion protection properties of polyimide‐silica and polyimide‐clay composite materials

Comparative studies on corrosion protection properties of polyimide‐silica‐clay composites were studied in this article. A series of polyimide‐silica (PIS), polyimide‐clay (PIC), and polyimide‐silica‐clay composites (PISC) materials, consisting of an organo‐soluble polyimide (ODA‐BSAA) matrix, inorganic silica particles prepared through the sol–gel reaction of tetraethyl orthosilicate (TEOS) and dispersed nanolayers of inorganic montmorillonite clay, were successfully prepared by solution dispersion technique. Then, all samples were characterized by FTIR, powder X‐ray diffraction patterns, transmission electron microscopy, and ²⁹Si solid‐state NMR. The main focus of this article is the comparison of the corrosion protection properties of PIS, PIC, and PISC composite materials. Normally, the aspect ratio of clay is higher than silica. Superior dispersion of clay platelets into a polymer matrix may effectively increase the length of diffusion pathways for oxygen and water. The effects of the materials composition on the corrosion protection performance, gas barrier, and optical properties, in the form of both coating and film, were also studied by electrochemical corrosion measurements (e.g., corrosion potential, polarization resistance, corrosion current, and impedance spectroscopy), gas permeability analysis, and UV‐visible transmission spectroscopy. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Poly(sodium 4‐styrene sulfonate) and poly(2‐acrylamido glycolic acid) polymer–clay ion exchange resins with enhanced mechanical properties and metal ion retention

This research presents the synthesis of novel nanocomposite ion exchange resins based on poly(sodium 4‐styrene sulfonate) and poly(2‐acrylamido glycolic acid). Nanocomposites were synthesized by in situ radical polymerization using organic modified montmorillonite as filler and different clay contents. Loaded resins showed improvements in mechanical properties compared with unloaded resins: specifically, when the nominal montmorillonite content was 2.5 wt%, poly(sodium 4‐styrene sulfonate) nanocomposite increased its shear modulus from 323 to 910 Pa and doubled its elastic recovery ratio, and the yield point was almost 20 times higher than for unloaded resins. In the case of metal ion retention, the effect of pH and clay content were studied for Cd(II), Pb(II), Cu(II), Cr(III) and Al(III) by a batch procedure. Results showed high efficiency, reaching over 80% after only 1 h of contact. Poly(2‐acrylamido glycolic acid) presented a higher pH dependence than poly(sodium 4‐styrene sulfonate). In addition, it was observed that montmorillonite contributes to retention capacity from the increase in distribution coefficients for loaded resins compared with unloaded resins. Copyright © 2011 Society of Chemical Industry