首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 31 毫秒
1.
This paper presents experimental results of rapeseed methyl ester (RME) and diesel fuel used separately as pilot fuels for dual-fuel compression-ignition (CI) engine operation with hydrogen gas and natural gas (the two gaseous fuels are tested separately). During hydrogen dual-fuel operation with both pilot fuels, thermal efficiencies are generally maintained. Hydrogen dual-fuel CI engine operation with both pilot fuels increases NOx emissions, while smoke, unburnt HC and CO levels remain relatively unchanged compared with normal CI engine operation. During hydrogen dual-fuel operation with both pilot fuels, high flame propagation speeds in addition to slightly increased ignition delay result in higher pressure-rise rates, increased emissions of NOx and peak pressure values compared with normal CI engine operation. During natural gas dual-fuel operation with both pilot fuels, comparatively higher unburnt HC and CO emissions are recorded compared with normal CI engine operation at low and intermediate engine loads which are due to lower combustion efficiencies and correspond to lower thermal efficiencies. This could be due to the pilot fuel failing to ignite the natural gas-air charge on a significant scale. During dual-fuel operation with both gaseous fuels, an increased overall hydrogen-carbon ratio lowers CO2 emissions compared with normal engine operation. Power output (in terms of brake mean effective pressure, BMEP) as well as maximum engine speed achieved are also limited. This results from a reduced gaseous fuel induction capability in the intake manifold, in addition to engine stability issues (i.e. abnormal combustion). During all engine operating modes, diesel pilot fuel and RME pilot fuel performed closely in terms of exhaust emissions. Overall, CI engines can operate in the dual-fuel mode reasonably successfully with minimal modifications. However, increased NOx emissions (with hydrogen use) and incomplete combustion at low and intermediate loads (with natural gas use) are concerns; while port gaseous fuel induction limits power output at high speeds.  相似文献   

2.
《Fuel》2006,85(14-15):2046-2056
The controlling strategies of homogeneous charge compression ignition (HCCI) fueled by dimethyl ether (DME) and methanol were investigated. The experimental work was carried out on a modified single-cylinder diesel engine, which was fitted with port injection of DME and methanol dual fuel. The results show that exhaust gas recirculation (EGR) rate and DME percentage are two important parameters to control the HCCI combustion process. The ignition timing and combustion duration can be regulated in a suitable range with high indicated thermal efficiency and low emissions by adjusting the DME percentage and EGR rate. EGR cannot extend the maximum indicate mean effective pressure (IMEP) of HCCI operation range with dual fuel, but can enlarge the DME percentage range in normal combustion. The combustion efficiency largely depends on DME percentage, and EGR can improve combustion efficiency. The results also show that HC emissions strongly depend upon DME percentage, and CO emissions have good coherence to the peak mean temperature in cylinder. In normal combustion, adopting large DME percentage and high EGR rate can attain an optimal HCCI combustion.  相似文献   

3.
Su Han Park  Chang Sik Lee 《Fuel》2011,90(2):748-755
The aim of this work is to investigate the effect of ethanol blending to diesel fuel on the combustion and exhaust emission characteristics of a four-cylinder diesel engine with a common-rail injection system. The overall spray characteristics, such as the spray tip penetration and the spray cone angle, were studied with respect to the ethanol blending ratio. A spray visualization system and a four-cylinder diesel engine equipped with a combustion and emission analyzer were utilized so as to analyze the spray and exhaust emission characteristics of the ethanol blending diesel fuel. Ethanol blended diesel fuel has a shorter spray tip penetration when compared to pure diesel fuel. In addition, the spray cone angle of ethanol blended fuels is larger. It is believed that the lower fuel density of ethanol blended fuels affects the spray characteristics. When the ethanol blended fuels are injected around top dead center (TDC), they exhibit unstable ignition characteristics because the higher ethanol blending ratio causes a long ignition delay. An advance in the injection timing also induces an increase in the combustion pressure due to the sufficient premixed duration. In a four-cylinder diesel engine, an increase in the ethanol blending ratio leads to a decrease in NOx emissions due to the high heat of evaporation of ethanol fuel, however, CO and HC emissions increase. In addition, the CO and HC emissions exhibit a decreasing trend according to an increase in the engine load and an advance in the injection timing.  相似文献   

4.
The effect of fuel constituents and exhaust gas recirculation (EGR) on combustion characteristics, fuel efficiency and emissions of a direct injection diesel engine fueled with diesel-dimethoxymethane (DMM) blends was investigated experimentally. Three diesel-DMM blended fuels containing 20%, 30% and 50% by volume fraction of DMM, corresponding to 8.5%, 12.7% and 21.1% by mass of oxygen in the blends, were used. By the use of DMM, it is observed that CO and smoke emissions as well as the total number and mass concentration of particulate reduce significantly, while HC emissions and particulate number with lower geometric mean diameters (Di < 0.039 μm) increase slightly. For each fuel, there is an increase of ignition delay whereas a decrease of cylinder pressure and heat release rate in the premixed combustion phase when the diesel engine was operated with EGR system. The brake thermal efficiency fluctuates at small EGR ratio, while decreases with the further increase of EGR ratio. With an increase of EGR ratio, NOx emission is reduced at the cost of increased smoke, HC and CO emissions as well as the total number and mass of particulates for each fuel.  相似文献   

5.
In this study, performance and exhaust emissions of biodiesel in a compression ignition engine was experimentally investigated. Therefore, biodiesel has been made by transesterification from cotton seed oil and then it was mixed with diesel fuel by 25% volumetrically, called here as B75 fuel. B75 fuel was tested, as alternative fuel, in a single cylinder, four strokes, and air-cooled diesel engine. The effect of B75 and diesel fuels on the engine power, engine torque and break specific fuel consumption were clarified by the performance tests. The influences of B75 fuel on CO, HC, NOx, Smoke opacity, CO2, and O2 emissions were investigated by emission tests. The engine torque and power, for B75 fuel, were lower than that of diesel fuel in range of 2-3%. However, for the B75, specific fuel consumption was higher than that of diesel fuel by approximately 3%. CO2, CO, HC, smoke opacity and NOx emissions of B75 fuel were lower than that of diesel fuel. The experimental results showed that B75 fuel can be substituted for the diesel fuel without any modifications in diesel engines.  相似文献   

6.
Myung Yoon Kim  Bong Woo Ryu 《Fuel》2008,87(12):2779-2786
The subject of this work is the investigation of the injection characteristics of neat dimethyl ether (DME) and the effect of DME fuel on the exhaust emission characteristics and engine performance of compression ignition engines. In order to analyze the injection characteristics of DME fuel as an alternative fuel for compression ignition engines, experiments were conducted to obtain the injection rate profile. The effective nozzle diameter and its velocity, and the discharge coefficient of the nozzle were analyzed by applying a nozzle flow model that accounted for the effect of cavitation. In addition, combustion characteristics of DME and diesel fuel in terms of combustion pressure, rate of heat release, indicated mean effective pressure (IMEP), and ignition delay at various injection timings were investigated on a constant energy input basis.When a constant pulse width was applied, the results of DME injection characterization showed that the actual injection duration of DME was longer than that of diesel fuel because the injection started faster and ended with more delay. The DME fueled engine showed slightly higher IMEP and NOx emission with drastically lower CO and HC emissions and the possible reasons for the higher IMEP of DME fuel was discussed.  相似文献   

7.
T. Lakshmanan  G. Nagarajan 《Fuel》2011,90(8):2571-2577
As the world finds itself in the midst of universal energy shortage, compounded by a parallel need to reduce pollutants of all kinds; we must take serious look at novel sources of abundant energy and methodology of its use. Acetylene with its remarkable combustion properties appear to be proving itself as the best fuel for future internal engines if it is utilised properly. Because of inherent difficulties in handling acetylene, technology has emphasized the utilization of acetylene by injection techniques to combat back fire in internal combustion engines. An experimental investigation was carried out on a single cylinder, air cooled, DI diesel engine designed to develop 4.4 kW at 1500 rpm. Acetylene was injected into the intake port as a secondary fuel and diesel was injected directly into the cylinder. The optimized injection time of 5° aTDC and injection duration of 90 °CA (9.9 ms) was arrived. The gas flow rate was fixed at 110 g/h, 180 g/h and 240 g/h. The combustion, performance and emission parameters were studied for the above flow rates by varying the load from low load to full load. Results show that NOx, HC and CO emissions reduced when compared to diesel operation due to leaner operation. A marginal increase in smoke emission was observed and brake thermal efficiency was nearer to diesel operation. On the whole it is concluded that without loss in thermal efficiency, safe operation of acetylene is possible in timed port injection technique. Reduced NOx, HC and CO emission levels, with marginal increase in smoke emission level were achieved.  相似文献   

8.
By the method of data collation, research into changes in life histories (ignition delay plus time of combustion) of the compounded fuel droplets (diesel fuel-biodiesel fuel (RME)-bioethanol), as well as diesel engine D-144 brake specific fuel consumption rates was performed and obtained results being compared to diesel fuel by an analogous manner.An optimum composition of the multi-component blend B30 + 7.5E demonstrating specific fuel consumption rates and droplet combustion characteristics very similar to diesel fuel was derived. In comparison to B30, a newly derived combustible blend demonstrated fairly improved emissions of exhaust gases. For low load mode: smoke opacity (−10%), NOX (−2%), CO (−20%), and HC (−12.5%). For average load mode: smoke opacity (−10%), NOX (−2%), CO (−22%), and HC (−14.5%). For high load mode: smoke opacity (−18%), NOX (−2%), CO (−22%), and HC (−18%).  相似文献   

9.
Aaron J. Reiter 《Fuel》2011,90(1):87-97
This study investigated the combustion and emissions characteristics of a compression-ignition engine using a dual-fuel approach with ammonia and diesel fuel. Ammonia can be regarded as a hydrogen carrier and used as a fuel, and its combustion does not produce carbon dioxide. In this study, ammonia vapor was introduced into the intake manifold and diesel fuel was injected into the cylinder to initiate combustion. The test engine was a four-cylinder, turbocharged diesel engine with slight modifications to the intake manifold for ammonia induction. An ammonia fueling system was developed, and various combinations of ammonia and diesel fuel were successfully tested. One scheme was to use different combinations of ammonia and diesel fuel to achieve a constant engine power. The other was to use a small quantity of diesel fuel and vary the amount of ammonia to achieve variable engine power. Under the constant engine power operation, in order to achieve favorable fuel efficiency, the preferred operation range was to use 40-60% energy provided by diesel fuel in conjunction with 60-40% energy supplied by ammonia. Exhaust carbon monoxide and hydrocarbon emissions using the dual-fuel approach were generally higher than those of using pure diesel fuel to achieve the same power output, while NOx emissions varied with different fueling combinations. NOx emissions could be reduced if ammonia accounted for less than 40% of the total fuel energy due to the lower combustion temperature resulting in lower thermal NOx. If ammonia accounted for the majority of the fuel energy, NOx emissions increased significantly due to the fuel-bound nitrogen. On the other hand, soot emissions could be reduced significantly if a significant amount of ammonia was used due to the lack of carbon present in the combination of fuels. Despite the overall high ammonia conversion efficiency (nearly 100%), exhaust ammonia emissions ranged from 1000 to 3000 ppmV and further after-treatment will be required due to health concerns. On the other hand, the variable engine power operation resulted in relatively poor fuel efficiency and high exhaust ammonia emissions due to the lack of diesel energy to initiate effective combustion of the lean ammonia-air mixture. The in-cylinder pressure history was also analyzed, and results indicated that ignition delay increased with increasing amounts of ammonia due to its high resistance to autoignition. The peak cylinder pressure also decreased because of the lower combustion temperature of ammonia. It is recommended that further combustion optimization using direct ammonia/diesel injection strategies be performed to increase the combustion efficiency and reduce exhaust ammonia emissions.  相似文献   

10.
Xingcai Lü  Yuchun Hou  Linlin Zu  Zhen Huang 《Fuel》2006,85(17-18):2622-2631
This article investigates the auto-ignition, combustion, and emission characteristics of homogeneous charge compression ignition (HCCI) combustion engines fuelled with n-heptane and ethanol/n-heptane blend fuels. The experiments were conducted on a single-cylinder HCCI engine using neat n-heptane, and 10%, 20%, 30%, 40%, and 50% ethanol/n-heptane blend fuels (by volume) at a fixed engine speed of 1800 r/min. The results show that, with the introduction of ethanol in n-heptane, the maximum indicated mean effective pressure (IMEP) can be expanded from 3.38 bar of neat n-heptane to 5.1 bar, the indicated thermal efficiency can also be increased up to 50% at large engine loads, but the thermal efficiency deteriorated at light engine load. Due to the much higher octane number of ethanol, the cool-flame reaction delays, the initial temperature corresponding the cool-flame reaction increases, and the peak value of the low-temperature heat release decreases with the increase of ethanol addition in the blend fuels. Furthermore, the low-temperature heat release is indiscernible when the ethanol volume increases up to 50%. In the case of the neat n-heptane and 10% ethanol/n-heptane blends, the combustion duration is very short due to the early ignition timing. For 20–50% ethanol/n-heptane blend fuels, the ignition timing is gradually delayed to the top dead center (TDC) by the ethanol addition. As a result, the combustion duration prolongs obviously at the same engine load when compared to the neat n-heptane fuel. At overall stable operation ranges, the HC emissions for n-heptane and 10–30% ethanol/n-heptane blends are very low, while HC emissions increase substantially for 40% and 50% ethanol/n-heptane blends. CO emissions show another tendency compared to HC emissions. At the engine load of 1.5–2.5 bar, CO emissions are very high for all fuels. Beside this range, CO emissions decrease both for large load and light load. In terms of operation stability of HCCI combustion, for a constant energy input, n-heptane shows an excellent repeatability and light cycle-to-cycle variation, while the cycle-to-cycle variation of the maximum combustion pressure and its corresponding crank angle, and ignition timing deteriorated with the increase of ethanol addition.  相似文献   

11.
Myung Yoon Kim  Chang Sik Lee   《Fuel》2007,86(17-18):2871-2880
The aim of this work was to investigate the effect of narrow fuel spray angle injection and dual injection strategy on the exhaust emissions of a common-rail diesel engine. To achieve successful homogeneous charge compression ignition by an early timing injection, a narrowed spray cone angle injector and a reduced compression ratio were employed. The combination of homogeneous charge compression ignition (HCCI) combustion and conventional diesel combustion was studied to examine the exhaust emission and combustion characteristics of the engine under various fuel injection parameters, such as injection timings of the first and second spray.The results showed that a dual injection strategy consisting of an early timing for the first injection for HCCI combustion and a late timing for the second injection was effective to reduce the NOx emissions while it suppress the deterioration of the combustion efficiency caused by the HCCI combustion.  相似文献   

12.
Partial combustion of biomass in the gasifier generates producer gas that can be used for heating purposes and as supplementary or sole fuel in internal combustion engines. In this study, the potential of coir-pith and wood chips as the feedstock for gasifier is analyzed. The performance of the gasifier–engine system is analyzed by running the engine for various producer gas–air flow ratios and at different load conditions. The system is experimentally optimized with respect to maximum diesel savings and lower emissions in the dual fuel mode operation while using coir-pith and wood chips separately. The performance and emission characteristics of the dual fuel engine are compared with that of diesel engine at different load conditions. Specific energy consumption in the dual fuel mode of operation is found to be in the higher side at all load conditions. The brake thermal efficiency of the engine while using wood chips in the dual mode operation is higher than that of coir-pith. The CO emission is higher in the case of dual fuel mode of operation as compared to that of diesel mode. In the dual fuel mode of operation, the higher diesel savings is achieved while using wood chips as compared to that of coir-pith. The comparison of the performance and emission characteristics of the dual fuel engine with diesel engine is also described.  相似文献   

13.
An experimental investigation was performed to study the influence of dual-fuel combustion characteristics on the exhaust emissions and combustion performance in a diesel engine fueled with biogas-biodiesel dual-fuel. In this work, the combustion pressure and the rate of heat release were evaluated under various conditions in order to analyze the combustion and emission characteristics for single-fuel (diesel and biodiesel) and dual-fuel (biogas-diesel and biogas-biodiesel) combustion modes in a diesel engine. In addition, to compare the engine performances and exhaust emission characteristics with combustion mode, fuel consumption, exhaust gas temperature, efficiency, and exhaust emissions were also investigated under various test conditions. For the dual-fuel system, the intake system of the test engine was modified to convert into biogas and biodiesel of a dual-fueled combustion engine. Biogas was injected during the intake process by two electronically controlled gas injectors, which were installed in the intake pipe.The results of this study showed that the combustion characteristics of single-fuel combustion for biodiesel and diesel indicated the similar patterns at various engine loads. In dual-fuel mode, the peak pressure and heat release for biogas-biodiesel were slightly lower compared to biogas-diesel at low load. At 60% load, biogas-biodiesel combustion exhibited the slightly higher peak pressure, rate of heat release (ROHR) and indicated mean effective pressure (IMEP) than those of diesel. Also, the ignition delay for biogas-biodiesel indicated shortened trends compared to ULSD dual-fueling due to the higher cetane number (CN) of biodiesel. Significantly lower NOx emissions were emitted under dual-fuel operation for both cases of pilot fuels compared to single-fuel mode at all engine load conditions. Also, biogas-biodiesel provided superior performance in reductions of soot emissions due to the absence of aromatics, the low sulfur, and oxygen contents for biodiesel.  相似文献   

14.
In the effort to reduce pollutant emissions from diesel engines various solutions have been proposed, one of which is the use of natural gas as supplement to liquid diesel fuel, with these engines referred to as fumigated, dual fuel, compression ignition engines. One of the main purposes of using natural gas in dual fuel (liquid and gaseous one) combustion systems is to reduce particulate emissions and nitrogen oxides. Natural gas is a clean burning fuel; it possesses a relatively high auto-ignition temperature, which is a serious advantage over other gaseous fuels since then the compression ratio of most conventional direct injection (DI) diesel engines can be maintained high. In the present work, an experimental investigation has been conducted to examine the effects of the total air-fuel ratio on the efficiency and pollutant emissions of a high speed, compression ignition engine located at the authors’ laboratory, where liquid diesel fuel is partially substituted by natural gas in various proportions, with the natural gas fumigated into the intake air. The experimental results disclose the effect of these parameters on brake thermal efficiency, exhaust gas temperature, nitric oxide, carbon monoxide, unburned hydrocarbons and soot emissions, with the beneficial effect of the presence of natural gas being revealed. Given that the experimental measurements cover a wide range of liquid diesel supplementary ratios without any appearance of knocking phenomena, the belief is strengthened that the findings of the present work can be very valuable if opted to apply this technology on existing DI diesel engines.  相似文献   

15.
P.K. Devan  N.V. Mahalakshmi 《Fuel》2009,88(5):861-867
Experimental tests have been carried out to evaluate the performance, emission and combustion characteristics of a diesel engine using Neat poon oil and its blends of 20%, 40%, and 60%, and standard diesel fuel separately. The common problems posed when using vegetable oil in a compression ignition engine are poor atomization; carbon deposits, ring sticking, etc. This is because of the high viscosity and low volatility of vegetable oil. When blended with diesel, poon oil presented lower viscosity, improved volatility, better combustion and less carbon deposit. It was found that there was a reduction in NOx emission for Neat poon oil and its diesel blends along with a marginal increase in HC and CO emissions. Brake thermal efficiency was slightly lower for Neat poon oil and its diesel blends. From the combustion analysis, it was found that poon oil-diesel blends performed better than Neat poon oil.  相似文献   

16.
Kuen Yehliu  Octavio Armas 《Fuel》2010,89(2):423-437
Few factors affect diesel combustion and emissions more significantly than the composition of the fuel and the fuel injection process. In this paper, both of these factors are considered by comparing conventional, synthetic and vegetable oil-derived diesel fuels and by comparing a single pulse injection and a split (pilot and main) injection process. This paper focuses on characterization of the combustion process and emissions produced by three substantially different diesel fuels: an ultra low sulfur diesel fuel (BP15), a pure soybean methyl ester (B100), and a synthetic, practically free of sulfur and aromatic compounds, Fischer-Tropsch fuel (FT) produced in a gas-to-liquid process. The study was carried out in a direct injection (DI) 2.5 L common-rail turbodiesel engine working at four engine operation modes, spanning conditions of most interest in the engine map. In all modes the engine was tested with single and split injection (pilot and main), with constant start of injection (SOI), and without exhaust gas recirculation (EGR). Using the results from thermodynamic analysis, this study confirms that the ignition character of the fuel affects the start of the combustion process, notably for the whole combustion process when the single injection is used, and during the combustion process after the pilot injection when the split injection is used. In general, the FT fuel can reduce both NOx and PM specific emissions in all modes under both single and split injection modes, bypassing the nitrogen oxides-particulate matter (NOx-PM) trade-off. Finally, this work confirms that biodiesel can reduce the particle concentration. However, in some cases an increase of PM mass emission has been observed and this increase of the PM mass emission is due to unburned or partially burned hydrocarbon (HC) emissions.  相似文献   

17.
Lei Zhu  C.S. Cheung  W.G. Zhang 《Fuel》2011,90(5):1743-1750
In this study, Euro V diesel fuel, biodiesel, and ethanol-biodiesel blends (BE) were tested in a 4-cylinder direct-injection diesel engine to investigate the combustion, performance and emission characteristics of the engine under five engine loads at the maximum torque engine speed of 1800 rpm. The results indicate that when compared with biodiesel, the combustion characteristics of ethanol-biodiesel blends changed; the engine performance has improved slightly with 5% ethanol in biodiesel (BE5). In comparison with Euro V diesel fuel, the biodiesel and BE blends have higher brake thermal efficiency. On the whole, compared with Euro V diesel fuel, the BE blends could lead to reduction of both NOx and particulate emissions of the diesel engine. The effectiveness of NOx and particulate reductions increases with increasing ethanol in the blends. With high percentage of ethanol in the BE blends, the HC, CO emissions could increase. But the use of BE5 could reduce the HC and CO emissions as well.  相似文献   

18.
The effects of mineral diesel fuel, gas-to-liquid fuel, rapeseed methyl ester, neat soybean and neat rapeseed oil on injection, combustion, efficiency and pollutant emissions have been studied on a compression ignition heavy duty engine operated near full load and equipped with a combined exhaust gas aftertreatment system (oxidation catalyst, particle filter, selective catalytic NOx reduction). In a first step, the engine calibration was kept constant for all fuels which led to differences in engine torque for the different fuels. In a second step, the injection duration was modified so that all fuels led to the same engine torque. In a third step, the engine was recalibrated in order to keep the NOx emissions at an equal level for all fuels (injection pressure, injection timing, EGR rate). The experiments show that the critical NOx emissions were higher (even behind the exhaust gas aftertreatment systems) for oxygenated fuels in case of the engine not being recalibrated for the fuel. GTL and the oxygenated fuels show lower emissions for some pollutants and higher efficiency after recalibration to equal NOx levels.  相似文献   

19.
C.H. Cheng  C.S. Cheung  T.L. Chan  S.C. Lee  C.D. Yao  K.S. Tsang   《Fuel》2008,87(10-11):1870-1879
Biodiesel is an alternative fuel for internal combustion engines. It can reduce carbon monoxide (CO), hydrocarbon (HC) and particulate matter (PM) emissions, compared with diesel fuel, but there is also an increase in nitrogen oxides (NOx) emission. This study is aimed to compare the effect of applying a biodiesel with either 10% blended methanol or 10% fumigation methanol. The biodiesel used in this study was converted from waste cooking oil. Experiments were performed on a 4-cylinder naturally aspirated direct injection diesel engine operating at a constant speed of 1800 rev/min with five different engine loads. The results indicate a reduction of CO2, NOx, and particulate mass emissions and a reduction in mean particle diameter, in both cases, compared with diesel fuel. It is of interest to compare the two modes of fueling with methanol in combination with biodiesel. For the blended mode, there is a slightly higher brake thermal efficiency at low engine load while the fumigation mode gives slightly higher brake thermal efficiency at medium and high engine loads. In the fumigation mode, an extra fuel injection control system is required, and there is also an increase in CO, HC and NO2 (nitrogen dioxide) and particulate emissions in the engine exhaust, which are disadvantages compared with the blended mode.  相似文献   

20.
The purpose of this study was to analyze the exhaust emissions of DME fuel through experimental and numerical analyses of in-cylinder spray behavior. To investigate this behavior, spray characteristics such as the spray tip penetration, spray cone angle, and spray targeting point were studied in a re-entrant cylinder shape under real combustion chamber conditions. The combustion performance and exhaust emissions of the DME-fueled diesel engine were calculated using KIVA-3V. The numerical results were validated with experimental results from a DME direct injection compression ignition engine with a single cylinder.The combustion pressure and IMEP have their peak values at an injection timing of around BTDC 30°, and the peak combustion temperature, exhaust emissions (soot, NOx), and ISFC had a lower value. The HC and CO emissions from DME fuel showed lower values and distributions in the range from BTDC 25° to BTDC 10° at which a major part of the injected DME spray was distributed into the piston bowl area. When the injection timing advanced to before BTDC 30°, the HC and CO emissions showed a rapid increase. When the equivalence ratio increased, the combustion pressure and peak combustion temperature decreased, and the peak IMEP was retarded from BTDC 25° to BTDC 20°. In addition, NOx emissions were largely decreased by the low combustion temperature, but the soot emissions increased slightly.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号