The enhancement effect of MoOx on Pd/C catalyst for the electrooxidation of formic acid

Molybdenum oxide (MoO_x) was added to a Pd/C catalyst using a novel two-step procedure. The enhancement effect of MoO_x on Pd/C catalyst for the electrooxidation of formic acid was verified by electrochemical experiments. Compared to the Pd/C catalyst, the experimental results showed that the addition of MoO_x could significantly enhance the electrocatalytic performances for the electrooxidation of formic acid. Significant improvements in electrocatalytic activity and stability were primarily ascribed to the effect of MoO_x on the Pd catalyst. In addition to the large specific surface area, the hydrogen spillover effect is speculated to have accelerated the electrooxidation rate of formic acid in the direct pathway.     

Electrosynthesis of Pd/Au hollow cone-like microstructures for electrocatalytic formic acid oxidation

Pd/Au hollow cone-like microstructures (HCMs) have been electrodeposited on indium tin oxide (ITO) using a two-step protocol, which involves the nucleation pulse and succedent constant potential reduction in the presence of metal precursors and polyvinylpyrrolidone (PVP). Scanning electron microscope (SEM), transmission electron microscope (TEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscope (XPS) were used to characterize the Pd/Au HCMs. The electrochemical results (cyclic voltammetry and chronoamperometry) testify that the Pd/Au HCMs exhibit significantly higher electrocatalytic activity and stability for the oxidation of formic acid than that of Pd/Au solid microhemispheres (SMHs). These attractive features are attributable to the unique hollow structures of Pd/Au with much higher electrochemical active surface areas and the exposure of favorable planes. Our work points to a new path for the preparation of Pd/Au HCMs, which are promising as electrocatalysts in direct formic acid fuel cell (DFAFC).     

Hydrogen Evolution and Hydrogen Oxidation on Palladium Bismuth Alloys

Thin film alloys of PdBi have been synthesised using a high throughput physical vapour deposition method to produce compositional gradients of PdBi alloys. XPS indicates that for the non-equilibrated thin films, the surface composition is the same as the bulk, and core level shifts reflect the inter-metallic interaction between the component metals. Hydrogen absorption is hindered in the PdBi alloys, and at a composition of 70 at.% bismuth, the ??Bi₂Pd bulk alloy phase is identified in XRD. This phase exhibits a maximum in the hydrogen evolution reaction (HER) and hydrogen oxidation reaction (HOR) electrocatalytic activity. The increased activity of the alloy can be understood in terms of the Pd d-band density of states, and a concomitant increase in the binding energy of hydrogen. There is a strong correlation between the HER and HOR activity as a function of composition across the complete range of alloys. The potential of using the ??Bi₂Pd bulk inter-metallic phase at the anode of PEM fuel cells is briefly discussed.     

络合还原法制备的Pd/C催化剂对甲酸氧化的电催化性能

分别以硼氢化钠和乙二醇为还原剂,经络合还原法制备了炭载钯（Pd/C）催化剂。透射电镜（TEM）和X射线粉末衍射谱（XRD）结果表明,以乙二醇为还原剂制备的Pd/C催化剂中Pd粒子具有较小的粒径、均匀的粒径分布和较大的相对结晶度,Pd粒子的平均粒径和相对结晶度分别为4.2±2 nm和1.88。电化学测试结果显示,以乙二醇为还原剂制备的Pd/C催化剂具有较大的电化学活性面积,对甲酸氧化表现出较高的电催化活性和稳定性。     

Screening of PdM and PtM catalysts in a multi-anode direct formic acid fuel cell

Direct formic acid fuel cells (DFAFC) currently employ either Pt-based or Pd-based anode catalysts for oxidation of formic acid. However, improvements are needed in either the activity of Pt-based catalysts or the stability of Pd-based catalysts. In this study, a number of carbon-supported Pt-based and Pd-based catalysts, were prepared by co-depositing PdM (M = Bi, Mo, or V) on Vulcan^® XC-72 carbon black, or depositing another metal (Pb or Sn) on a Pt/C catalyst. These catalysts were systematically evaluated and compared with commercial Pd/C, PtRu/C, and Pt/C catalysts in a multi-anode DFAFC. The PtPb/C and PtSn/C catalysts were found to show significantly higher activities than the commercial Pt/C catalyst, while the PdBi/C provided higher stability than the commercial Pd/C catalyst.     

ZrC–C and ZrO2–C as Novel Supports of Pd Catalysts for Formic Acid Electrooxidation

The Pd/ZrC–C and Pd/ZrO₂–C catalysts with zirconium compounds ZrC or ZrO₂ and carbon hybrids as novel supports for direct formic acid fuel cell (DFAFC) have been synthesized by microwave‐assisted polyol process. The Pd/ZrC–C and Pd/ZrO₂–C catalysts have been characterized by X‐ray diffraction (XRD), X‐ray photoelectron spectroscopy (XPS), energy dispersive analysis of X‐ray (EDAX), transmission electron microscopy (TEM), and electrochemical measurements. The physical characteristics present that the zirconium compounds ZrC and ZrO₂ may promote the dispersion of Pd nanoparticles. The results of electrochemical tests show that the activity and stability of Pd/ZrC–C and Pd/ZrO₂–C catalysts show higher than that of Pd/C catalyst for formic acid electrooxidation due to anti‐corrosion property of zirconium compounds ZrC, ZrO₂, and metal–support interaction between Pd nanoparticles and ZrC, ZrO₂. The Pd/ZrC–C catalyst displays the best performance among the three catalysts. The peak current density of formic acid electrooxidation on Pd/ZrC–C electrode is nearly 1.63 times of that on Pd/C. The optimal mass ratio of ZrC to XC‐72 carbon is 1:1 in Pd/ZrC–C catalyst with narrower particle size distribution and better dispersion on surface of the mixture support, which exhibits the best activity and stability for formic acid electrooxidation among all the samples.     

络合还原法制备Pd/C催化剂及甲酸电催化氧化性能

分别以硼氢化钠和乙二醇为还原剂,经络合还原法制备了炭载钯(Pd/C)催化剂。透射电镜(TEM)和X射线粉末衍射谱(XRD)结果表明,以乙二醇为还原剂制备的Pd/C催化剂中Pd粒子具有较小的粒径、均匀的粒径分布和较大的相对结晶度,Pd粒子的平均粒径和相对结晶度分别为(4.2±2)nm和1.88。电化学测试结果显示,Pd/C催化剂具有较大的电化学活性面积,对甲酸氧化表现出较高的电催化活性和稳定性。     

Fabrication of Pt–Cu/RGO hybrids and their electrochemical performance for the oxidation of methanol and formic acid in acid media

Pt–Cu/reduced graphene oxide (Pt–Cu/RGO) hybrids with different Pt/Cu ratios were prepared by the reduction of H₂PtCl₆ and CuSO₄ by NaBH₄ in the presence of graphene oxide (GO). The Pt–Cu nanoparticles were characterized by transmission electron microscopy, X-ray diffraction and X-ray photoelectron spectroscopy. The reduction of GO was verified by ultraviolet–visible absorption spectroscopy, Raman spectroscopy and X-ray photoelectron spectroscopy. Compared to Pt/RGO, the Pt–Cu/RGO hybrids have superior electrocatalytic activity and stability for the oxidation of methanol and formic acid. Thus they should have potential applications in direct methanol and formic acid fuel cells.     

Electrocatalytic properties of Pd clusters on Au nanoparticles in formic acid electro-oxidation

Pd clusters were formed on highly dispersed Au nanoparticles (∼3.5 nm in diameter) using a seed-mediated growth process. The structural information and electrocatalytic activities of these Pd clusters on Au nanoparticles were confirmed by high-resolution-transmission-electron microscopy (HR-TEM), X-ray photoelectron spectroscopy (XPS) and cyclic voltammetry (CV). The resulting nanoparticles, which had a uniform size (<5 nm in diameter), were highly dispersed on carbon particles, and Pd clusters (<0.44 nm in size, <2 atomic layers) were formed selectively on Au nanoparticles. XPS results show that the Pd 3d_5/2 peak shifted to lower binding energies and that the amount of surface oxide decreased as the Pd content was decreased on the Au nanoparticles. In formic acid electro-oxidation, these Pd clusters exhibit enhanced electrocatalytic activity relative to that of carbon-supported Pd nanoparticles. These results may be due to the modified electronic and geometric structure of the Pd clusters on the Au nanoparticle substrate.     

Electrocatalytic performance of carbon nanotube-supported palladium particles in the oxidation of formic acid and the reduction of oxygen

We describe a simple approach for the synthesis of nanosized Pd particles supported on multiwall carbon nanotubes (MWCNTs) and their electrocatalytic performance in the oxidation of formic acid and the reduction of oxygen. The metal precursors are pre-organized on poly(diallyldimethylammonium) chloride-wrapped MWCNTs by electrostatic interaction and chemically reduced to obtain Pd nanoparticles. The MWCNT-supported nanoparticles are characterized by UV-visible spectroscopy, X-ray diffraction (XRD), scanning and transmission electron microscopy and electrochemical measurements. MWCNTs are uniformly decorated with closely packed array of nanoparticles. The nanoparticles on the MWCNTs have spherical and rod-like shapes with size ranging from 5 to 10 nm. XRD and selected area electron diffraction measurements of the nanoparticles show (1 1 1), (2 0 0) and (2 2 0) reflections of the Pd lattice. The electrocatalytic activity of the nanoparticles towards oxidation of formic acid and reduction of oxygen is examined in acidic solution. The MWCNT-supported particles exhibit excellent electrocatalytic activity. The electrocatalytic reduction of oxygen follows the peroxide pathway. Surface morphology and coverage of particles on the nanotubes control the electrocatalytic activity. The large surface area and high catalytic activity of the MWCNT-supported nanoparticles facilitate the electrocatalytic reactions at a favorable potential.     

Synthesis of Pd/C Catalyst by Modified Polyol Process for Formic Acid Electrooxidation

Pd catalyst supported on Vulcan XC‐72 carbon black was prepared by a modified polyol process. Its performance was compared with that of Pd/C catalyst prepared by impregnation reduction method by using NaBH₄ as a reducing agent for formic acid electrooxidation. Their physical characterisations were tested by means of energy dispersive analysis of X‐ray, X‐ray diffraction and transmission electron micrographs. Their activities were presented by cyclic voltammetry and chronoamperometry. The results show that the particle sizes of Pd/C catalysts prepared by modified polyol process and impregnation reduction method are 3.9 and 7.9 nm, respectively. The size dispersion of the former is narrower and more homogeneous than that of the latter. However, both of Pd/C catalysts display the characteristic diffraction peaks of a Pd face‐centred cubic (f.c.c.) crystal structure. The results of electrochemical measurements present that the Pd/C catalyst prepared by modified polyol process has the higher electrocatalytic activity and stability for formic acid electrooxidation in comparison to the Pd/C one by impregnation reduction method due to the particle size effect, and its peak current density of CV and the current of chronoamperometric curve at 1,000 s reach 33.2 and 11.2 mA cm^–2, respectively.     

载体的碱处理对Pd/C催化剂电催化性能的影响

将活性炭放入质量分数为10%的NaOH溶液中进行预处理,然后将其与未处理的活性炭分别作为载体制备Pd/C催化剂。对比两种催化剂的电化学性能发现,预处理的活性炭所制备的Pd/C催化剂,在甲酸电催化氧化活性和稳定性方面好于未处理的活性炭所制备的Pd/C催化剂。     

Facile template-free synthesis of pine needle-like Pd micro/nano-leaves and their associated electro-catalytic activities toward oxidation of formic acid

Pine needle-like Pd micro/nano-leaves have been synthesized by a facile, template-free electrochemical method. As-synthesized Pd micro/nano-leaves were directly electrodeposited on an indium tin oxide substrate in the presence of 1.0 mM H2PdCl4 + 0.33 M H3PO4. The formation processes of Pd micro/nano-leaves were revealed by scanning electron microscope, and further characterized by X-ray diffraction and electrochemical analysis. Compared to conventional Pd nanoparticles, as-prepared Pd micro/nano-leaves exhibit superior electrocatalytic activities for the formic acid oxidation.     

Ultraporous Palladium Supported on Graphene‐Coated Carbon Fiber Paper as a Highly Active Catalyst Electrode for the Oxidation of Methanol

Ultraporous Pd nanocrystals for electrocatalysis applications were fabricated using a direct electrodeposition method on three differing carbon supports: flexible carbon fiber paper (CFP), and CFP modified with either graphene oxide nanosheets or their chemically reduced forms using a simple spray coating technique. The electrocatalytic activity of these electrodes was investigated for the direct electro‐oxidation reaction of methanol in alkaline media. Pd deposited on the CFP modified with reduced graphene oxide (rGO) has excellent poisoning tolerance to carbonaceous species and a significantly better catalytic activity toward methanol oxidation than the other two catalyst support materials. Pd/rGO/CFP in 2.0 M CH₃OH in 2.0 M NaOH yields a specific current density of 241 mAmg^–1 cm^–2 determined at the anodic oxidation peak. It is believed that the collaborative effects due to the three‐dimensional ultraporous Pd nanocrystals and fast electron transfer owing to high conductivity of rGO nanosheets play an important role in enhancing the catalytic performance of Pd/rGO/CFP toward methanol oxidation in alkali media.     

Ultrasonic-assisted synthesis of Pd–Ni alloy catalysts supported on multi-walled carbon nanotubes for formic acid electrooxidation

Pd–Ni alloys with different compositions (i.e. Pd₂Ni, PdNi, PdNi₂) dispersed on multi-walled carbon nanotubes (MWCNTs) are prepared by ultrasonic-assisted chemical reduction. The X-ray diffraction (XRD) patterns indicate that all Pd and Pd–Ni nanoparticles exist as Pd face-centered cubic structure, while Ni alloys with Pd. The transmission electron microscopy (TEM) images show the addition of nickel decreases the particle size and improves the dispersion. The X-ray photoelectron spectroscopy (XPS) spectra demonstrate the electronic modification of Pd by nickel doping. The electrochemical measurements reveal that the PdNi catalysts have better catalytic activity and stability for formic acid electrooxidation, among them PdNi/MWCNTs is the best. The performance enhancement is ascribed to the increase of electroactive surface area (EASA) and nickel doping effect which might modify the electronic structure.     

碳载PdCo合金催化剂对甲酸的电催化氧化

用间歇式微波法制备了不同Pt：Co原子比的碳载PdCo合金催化剂（PdCo／C）,发现在酸性溶液中Pd：Co原子比2：1催化剂对甲酸的电氧化有良好的催化活性和稳定性。从H在电极表面的吸脱附峰计算出来的结果表明,催化剂中加入一定比例的金属Co能够增加催化剂的电化学比表面。     

Novel catalyst-support interaction for direct formic acid fuel cell anodes: Pd electrodeposition on surface-modified graphite felt

The electrodeposition of Pd on graphite felt (GF, thickness ~3 mm in uncompressed state) was studied and the resulting catalyst was compared with Pt-Ru/GF for the electro-oxidation of formic acid. A micellar solution composed of the non-ionic surfactant Triton X-102 and an aqueous phase containing PdCl₂ were utilized for the galvanostatic electrodeposition of Pd nanoparticles. The presence of the surfactant during electrodeposition coupled with pretreatment of the GF surface by a Shipley-type method (PdCl₂ + SnCl₂ solution) creating nucleation sites had a major impact on the Pd catalyst morphology and penetration throughout the electrode thickness, affecting, therefore, the electrocatalytic activity toward formic acid oxidation. It was found that large (~1,000 nm) Pd particles with smooth surface favored the indirect CO_ad pathway, while Pd nanoparticles (diameter <40 nm) with rough surface, formed with surfactant and pretreatment, were much more active leading to the direct non-CO_ad pathway. Due to pretreatment the GF surface has been modified and the effective catalytic system could be described as Pd/SnO₂–Pd(PdO)/GF with possible electronic interaction between support and catalyst. In direct formic acid fuel cell (DFAFC) experiments at 333 K and 1 M HCOOH, the peak power density using the Pd/GF anode reached 852 W m^?2 (57 g m^?2 Pd) compared to 392 W m^?2 (40 g m^?2 Pd) with a commercial Pd catalyst-coated membrane (CCM). The long-term stability of Pd-based anodes was poor and inferior to Pt–Ru (4:1 at. ratio) prepared and tested under identical conditions.     

Effect of pH Value and Temperatures on Performances of Pd/C Catalysts Prepared by Modified Polyol Process for Formic Acid Electrooxidation

The highly active Pd/C catalysts for formic acid electrooxidation have been prepared by a modified polyol process at different pH values of reaction solutions and different reducing temperatures, respectively. Their physical properties have been characterised by energy dispersive analysis of X‐ray, X‐ray diffraction and transmission electron microscopy. Their electrochemical performances for formic acid electrooxidation have been tested by cyclic voltammetry and amperometric i–t curves. The results of physical characterisations show that all the Pd/C catalysts present an excellent face centered cubic crystalline structure. Their particle sizes are decreasing firstly and then increasing with the increasing of the pH values of reaction solutions. The reducing temperatures also markedly affect the Pd particle sizes. And their nanoparticles have narrow size distributions and are highly dispersed on the surface of carbon support, and Pd metal loading in Pd/C catalyst is similar to the theoretical value of 20 wt.%. The results of electrochemical measurements present that the Pd/C catalyst prepared by waterless polyol process at the pH value of 10 and the reducing temperature of 120 °C has the smallest particle size of about 5.6 nm, and exhibits the highest catalytic activity (1172.0 A · g_Pd<?h‐2.85>^–1<?h.8>) and stability for formic acid electrooxidation.     

Preparation of high performance Pd catalysts supported on untreated multi-walled carbon nanotubes for formic acid oxidation

Due to the inherent inertness of carbon nanotubes (CNTs), one of the most significant challenges in the preparation of CNT-supported catalysts is achieving a uniform deposition of nanoparticles on the surface of the nanotubes. In this paper, we report on the preparation and characterization of Pd nanoparticles supported on untreated multi-walled carbon nanotubes (MWCNTs), synthesized in the presence of glutamate. The results of Raman spectroscopy revealed that this synthetic procedure does not have a detrimental effect on the surface structure of MWCNTs. Transmission electron microscopy (TEM) measurements indicated that the dispersion of Pd nanoparticles on untreated-MWCNTs in the presence of glutamate were uniform, and a narrow particle size was observed. X-ray diffraction (XRD) patterns indicated that the Pd/MWCNT catalyst possessed a face-centered cubic crystal structure. Cyclic voltammetry and chronoamperometry tests demonstrated that the obtained Pd/MWCNT catalyst displayed superior electrocatalytic activity and stability in formic acid oxidation, as compared to both a Pd/MWCNT catalyst synthesized without glutamate and a Pd catalyst on acid-oxidized MWCNTs, under otherwise identical experimental conditions. These results indicate that the catalyst developed in this study is a superior candidate for direct formic acid fuel cells (DFAFCs).     

Sonochemical synthesis of Pt-doped Pd nanoparticles with enhanced electrocatalytic activity for formic acid oxidation reaction

Pt-doped Pd nanoparticle catalysts (Pd _n Pt, n is 12, 15 and 19) supported on carbon were synthesized by an ultrasound assisted polyol method. The catalysts were characterized by X-ray diffraction, transmission electron microscopy, and energy dispersive X-ray spectroscopy. The electrochemical activity of the electrocatalysts was investigated in terms of formic acid oxidation reaction (FAOR) at low concentration of formic acid in 0.1 M perchloric acid at room temperature. Formic acid oxidation on the Pd _n Pt/C commences at lower potential than a commercial Pt/C. Pd₁₉Pt/C catalyst showed the highest catalytic activity in FAOR compared to that of other catalysts. The obtained electrochemical results from voltammograms indicate that Pt-doped Pd catalysts can be a promising candidate for the anode material in direct formic acid fuel cells. The synthesis procedure is not only a very facile route but also a mass producible method for preparing carbon supported alloy nanoparticles.