共查询到20条相似文献,搜索用时 921 毫秒
1.
对于已投入运行的供汽管网,其凝结水量同时受到供汽流量、供汽压力、供汽温度及环境温度等因素的影响。为探究供汽管网与这些影响因素之间的关系,以某供汽管网为例,借助Gensystem模型开发平台,构建了管网仿真模型,得到了管网凝结水量与其影响因素之间的关系,并分析了各影响因素扰动时凝结水量的动态变化趋势。结果表明:管网在供汽流量8.33 kg/s(30 t/h)、供汽压力1 MPa、供汽温度280 ℃、环境温度20 ℃工况下,供汽流量每升高2.78 kg/s(10 t/h),管网凝结水量降低33.3%;供汽压力每升高0.1 MPa,凝结水量增大24.0%;供汽温度每升高10 ℃,凝结水量降低7.1%;环境温度每升高10 ℃,凝结水量降低6.8%。管网凝结水量对供汽压力有较大的敏感性,供汽压力升高时,管网凝结水量会在短时间内有一骤增过程,容易出现大量凝结水聚集,造成安全隐患。 相似文献
2.
3.
凝结水过冷度对机组的安全和经济运行有重要的影响。该文采用严谨的数学理论,推导了凝结水过冷度的变化对抽汽量的影响,证明了当凝结水过冷度发生变化时,对于不同的疏水连接方式,流过加热器的凝结水量有的发生变化,有的不变。并就不同疏水连接方式下凝结水过冷度对机组经济性的影响进行了定量分析计算。 相似文献
4.
5.
凝结水溶解氧量是表征凝结水水质的重要指标之一。它直接影响机组的经济性和安全性。国内目前还没有针对空冷机组的凝结水溶氧指标,暂时只能沿用湿冷机组的控制值。目前我国已投产的直接空冷机组,普遍存在凝结水溶氧量偏大的问题。文章分析了凝结水溶解氧量的存在机理和影响因素,介绍了3种补水方式,即凝结水补水到主凝结水箱、补水管路接至空冷凝汽器、直接空冷系统的补水到汽轮机的主排汽管道,并对此3种补水方式的优缺点进行了对比。提出了控制凝结水溶氧量偏大应采取的措施。 相似文献
6.
7.
8.
为解决9F级单轴燃气蒸汽联合循环机组启动频繁,启动时凝结水含氧量过高,以及由辅汽造成启动时凝汽器水量过大的问题,通过不同类型9F单轴机组凝结水系统的分析,可知启动除氧器或带加热蒸汽的凝汽器可解决启动除氧的问题,通过补给水母管或大容量凝结水箱可解决凝结水量平衡的问题。 相似文献
9.
除氧器是热力系统中的重要设备,它有对给水加热、储存凝结水和除氧的功能。正常运行时,除氧器的水主要从凝汽器由凝结水泵打入,因此,除氧器的水位控制和凝汽器水位有着十分密切的联系。除氧器水位是通过调节进入除氧器的凝结水来满足要求的,而凝结水流量又直接影响凝汽器水位,如果凝结水流量大幅度地变化,则凝汽器水位也会大幅度地变化旗毛汽器水位的稳定取决于凝结水流量与凝汽量和化补水的平衡,由于凝汽量取决汽机负荷,汽机负荷不变时,凝汽量基本不变, 相似文献
10.
11.
12.
13.
Yuan Chen Westergard L. Mojarradi M.M. Johnson T.W. Cozy R.S. Billman C. Burke G.R. Kolawa E.A. 《Device and Materials Reliability, IEEE Transactions on》2006,6(2):146-153
A design for reliability methodology has been developed for electronics for low-temperature applications. A hot carrier aging (HCA) lifetime projection model is proposed to take into account the HCA impact on technology, analysis of parametric degradation versus critical circuit path degradation, transistor bias profile, transistor substrate current profile, and operating temperature profile. The most applicable transistor size can be determined in order to meet the reliability requirements of the electronics operating under low temperatures. This methodology and approach can also be applied to other transistor-level failure and/or degradation mechanisms for applications with varying temperature ranges. 相似文献
14.
15.
《Power Delivery, IEEE Transactions on》1998,13(1):73-77
IEEE Standard 1344, Synchrophasors for Power Systems, was completed in 1995. It sets parameters required to ensure that phasor measurement will be made and communicated in a consistent manner. It specifies requirements for the timing signal used for phasor synchronization and the time code needed for input to a measurement unit. GPS is the recommended time source and IRIG-B is the basic format used for time communication. The standard requires correlating phasors computed from unsynchronized and synchronized sampling to a common basis. Timetagging accurately and consistently is essential for wide area comparison of phase. The standard specifies information exchange and control message formats. These include data output, configuration, and command messages. It includes 7 annexes that discuss the concepts covered in the body of the standard 相似文献
16.
17.
18.
19.
20.
分析了GIS断路器故障原因,介绍了检验过程与充气检查、监督情况,并提供一些可借鉴的成功经验。 相似文献