Wide gap p-type degenerate semiconductor: Mg-doped LaCuOSe

Hole transport and optical properties were investigated on undoped and Mg-doped LaCuOS_1−xSe_x (x=0-1) epitaxial films. Both electrical conductivity and Hall mobility were found to increase monotonously with increasing Se content in the films. The increase in Hall mobility is considered to be associated with the increase in valence band dispersion. Mg ion doping increased hole concentrations in the undoped films by an order of magnitude to ∼2×10²⁰ cm⁻³, while Mg doping reduced mobility to merely half that of undoped films. The results suggest that hole scattering due to Mg impurity ions is suppressed by natural modulation doping originating from the layered structure of LaCuOS_1−xSe_x. Hole concentrations showed no temperature dependence, indicating degenerate conduction. The largest value for conductivity, 140 S cm⁻¹, was obtained with Mg-doped LaCuOSe epitaxial film. Accompanying characteristics included moderately high optical transparency in the visible region and blue photoluminescence.     

Growth and characterization of tin oxide thin films and fabrication of transparent p-SnO/n-ZnO p–n hetero junction

p-Type and n-type tin oxide thin films were deposited by rf-magnetron sputtering of metal tin target by varying the oxygen pressure. Chemical composition of SnO thin film according to the intensity of the XPS peak is about 48.85% and 51.15% for tin and oxygen respectively. Nearest neighbor distance of the atoms calculated from SAED patterns is 2.9 Åand 2.7 Åfor SnO and SnO₂ respectively. The Raman scattering spectrum obtained from SnO thin films showed two peaks, one at 113 cm⁻¹ and the other at 211 cm⁻¹. Band gap of as-deposited SnO_x thin films vary from 1.6 eV to 3.2 eV on varying the oxygen partial pressure from 3% to 30% which indicates the oxidization of metallic phase Sn to SnO and SnO₂. p-Type conductivity of SnO thin films and n-type conductivity of SnO₂ thin films were confirmed through Hall coefficient measurement. Transparent p–n hetero junction fabricated in the structure glass/ITO/n-ZnO/p-SnO shows rectification with forward to reverse current ratio as 12 at 4.5 V.     

Raman analysis of nitrogen doped ZnO

The mechanism of nitrogen doping is essential for making p-type ZnO. This paper demonstrates that Raman characterization is a potentially powerful tool to study the mechanism of nitrogen doping. We have observed new Raman features near 280, 510, 570, 642, 773, 1360 and 1565 cm^− 1 shift in nitrogen doped ZnO (ZnO:N) thin films compared with undoped ZnO films. Peaks at 280, 510, 570, 642, and 773 cm^− 1 are attributed to the nitrogen related defect complex. The Raman peaks at 1360 cm^− 1 and 1565 cm^− 1 shift are assigned to D—(disordered) and G—(Graphitic) bands associated with the carbon-related defect complex, respectively. The intensity and the intensity ratio of peaks at 1360 cm^− 1 and 1565 cm^− 1 have been found to be sensitive parameters that reflect the conductivity type of ZnO:N. Explanations are presented which correlate the Raman features to the electric conductivity of the films. From this analysis, we found that at temperature lower than or at 400 °C, nitrogen incorporation will form the nitrogen or possible nitrogen carbon related defect complex. As the growth temperature increases to 500 °C, the features associated with nitrogen are difficult to distinguish and the features associated to carbon begin to emerge. This observation possibly indicates the decrease of the nitrogen content and the increase of the carbon content in the ZnO:N film. The increase of carbon content may affect the donor behavior of the film. This observation suggests that growth conditions should be controlled to avoid carbon into the film.     

Stable p-type conductivity and enhanced photoconductivity from nitrogen-doped annealed ZnO thin film

We report on the growth of p-type ZnO thin films with improved stability on various substrates and study the photoconductive property of the p-type ZnO films. The nitrogen doped ZnO (N:ZnO) thin films were grown on Si, quartz and alumina substrates by radio frequency magnetron sputtering followed by thermal annealing. Structural studies show that the N:ZnO films possess high crystallinity with c-axis orientation. The as-grown films possess higher lattice constants compared to the undoped films. Besides the high crystallinity, the Raman spectra show clear evidence of nitrogen incorporation in the doped ZnO lattice. A strong UV photoluminescence emission at ~ 380 nm is observed from all the N:ZnO thin films. Prior to post-deposition annealing, p-type conductivity was found to be unstable at room temperature. Post-growth annealing of N:ZnO film on Si substrate shows a relatively stable p-type ZnO with room temperature resistivity of 0.2 Ω cm, Hall mobility of 58 cm²/V s and hole concentration of 1.95 × 10¹⁷ cm^− 3. A homo-junction p-n diode fabricated on the annealed p-type ZnO layer showed rectification behavior in the current-voltage characteristics demonstrating the p-type conduction of the doped layer. Doped ZnO films (annealed) show more than two orders of magnitude enhancement in the photoconductivity as compared to that of the undoped film. The transient photoconductivity measurement with UV light illumination on the doped ZnO film shows a slow photoresponse with bi-exponential growth and bi-exponential decay behaviors. Mechanism of improved photoconductivity and slow photoresponse is discussed based on high mobility of carriers and photodesorption of oxygen molecules in the N:ZnO film, respectively.     

RF diode reactive sputtering of n- and p-type zinc oxide thin films

We present the relationship between parameters of reactive RF diode sputtering from a zinc oxide (ZnO) target and the crystalline, electrical and optical properties of n-/p-type ZnO thin films. The properties of the ZnO thin films depended on RF power, substrate temperature and, particularly, on working gas mixtures of Ar/O₂ and of Ar/N₂. Sputtering in Ar+O₂ working gas (up to 75% of O₂) improved the structure of an n-type ZnO thin film, from fibrous ZnO grains to columnar crystallites, both preferentially oriented along the c-axis normally to the substrate (〈0 0 2〉 direction). These films had good piezoelectric properties but also high resistivity (ρ≈10³ Ω cm). ZnO:N p-type films exhibited nanograin structure with preferential 〈0 0 2〉 orientation at 25% N₂ and 〈1 0 0〉 orientation for higher N₂ content. The presence of nitrogen N_O at O-sites forming N_O-O acceptor complexes in ZnO was proven by SIMS and Raman spectroscopy. A minimum value of resistivity of 790 Ω cm, a p-type carrier concentration of 3.6×10¹⁴ cm⁻³ and a Hall mobility of 22 cm² V⁻¹ s⁻¹ were obtained at 75% N₂.     

Tungsten-doped ZnO transparent conducting films deposited by direct current magnetron sputtering

Highly conducting and transparent thin films of tungsten-doped ZnO (ZnO:W) were prepared on glass substrates by direct current (DC) magnetron sputtering at low temperature. The effect of film thickness on the structural, electrical and optical properties of ZnO:W films was investigated. All the deposited films are polycrystalline with a hexagonal structure and have a preferred orientation along the c-axis perpendicular to the substrate. The electrical resistivity first decreases with film thickness, and then increases with further increase in film thickness. The lowest resistivity achieved was 6.97 × 10⁻⁴ Ω cm for a thickness of 332 nm with a Hall mobility of 6.7 cm² V⁻¹ s⁻¹ and a carrier concentration of 1.35 × 10²¹ cm⁻³. However, the average transmittance of the films does not change much with an increase in film thickness, and all the deposited films show a high transmittance of approximately 90% in the visible range.     

Effect of annealing temperature on structural, electrical and optical properties of B-N codoped ZnO thin films

The B-N codoped p-type ZnO thin films have been prepared by radio frequency magnetron sputtering using a mixture of nitrogen and oxygen as sputtering gas. The effect of annealing temperature on the structural, electrical and optical properties of B-N codoped films was investigated by using X-ray diffraction, Hall-effect, photoluminescence and optical transmission measurements. Results indicated that the electrical properties of the films were extremely sensitive to the annealing temperature and the conduction type could be changed dramatically from n-type to p-type, and finally changed to weak p-type in a range from 600 °C to 800 °C. The B-N codoped p-type ZnO film with good structural, electrical and optical properties can be obtained at an intermediate annealing temperature region (e.g., 650 °C). The codoped p-type ZnO had the lowest resistivity of 2.3 Ω cm, Hall mobility of 11 cm²/Vs and carrier concentration of 1.2 × 10¹⁷ cm^− 3.     

Effect of crystallographic orientations on electrical properties of sputter-deposited nickel oxide thin films

Nickel oxide thin films of various preferred orientations were deposited by radio-frequency (RF) magnetron sputtering process in different gas ratios of oxygen atmosphere at RF power 200 W on unheated and heated for (673 K) substrates. The relationships among substrate temperature, preferred orientation and electrical properties of the NiO films were investigated. The resulting films were analyzed by grazing-incidence X-ray diffraction, high-resolution transmission electron microscopy (HR-TEM), and ultrahigh resolution scanning electron microscopy (HR-SEM). The electrical properties were measured using four probe and Hall effects measurements. The results show that films deposited at room temperature with the ratio of oxygen varying from 0 to 100% develop a (111) preferred orientation. At temperature of 673 K, while the (111)-orientated film was obtained under a low ratio of oxygen (<50% O₂), a (200) preferred orientation was developed under 100% oxygen. The lowest sheet resistance 0.01 MΩ/□, resistivity 0.83 Ω-cm and higher carrier density 7.35 × 10¹⁸ cm⁻³ could be obtained on (111) preferred orientation samples prepared on unheated substrates in pure oxygen atmosphere. The relationship between preferred orientation and electrical properties was proposed in this paper.     

Chemically deposited thin films of PbSe as an absorber component in solar cell structures

PbSe thin films were prepared by chemical deposition using dimethylselenourea as a source of selenide ions. Depending on the duration (30 min to 4 h) and temperature (30-60 °C) of the deposition, and the substrate, the films show a high degree of preferred orientation for the (111) planes. The texture coefficients could be up to 5 for these planes. The crystallite diameters are in the 30-35 nm range, and optical bad gap, 0.4-0.7 eV. The electrical conductivity is p-type, 0.01-10 (Ω cm)^− 1. These films were deposited over CdS/Sb₂S₃ or CdS/Sb₂Se₃ solar cell structures as an additional absorber. In a CdS/Sb₂Se₃/PbSe cell, this addition increases the short circuit current density (J_sc) from 0.2 mA/cm² to 8.9 mA/cm² and conversion efficiency (η) from 0.04% to 0.99%. In a CdS/Sb₂S₃/PbSe cell, J_sc is 5.91 mA/cm²; η, 0.98%; and open circuit voltage, 560 mV.     

P-type transparent Ti-V oxides semiconductor thin film as a prospective material for transparent electronics

In this paper electrical and optical properties of mixed titanium and vanadium oxides (Ti-V oxides) thin films have been outlined. Thin films were deposited by sputtering of mosaic Ti-V target in reactive oxygen plasma using high energy magnetron sputtering process. From elemental analysis results, 19 at.% of vanadium was incorporated into thin films and X-ray diffraction investigations displayed their amorphous behavior. However, images obtained by the use of an atomic force microscope displayed a densely packed nanocrystalline structure. It has been found that V addition considerably improves the electrical conduction of prepared Ti-V oxide thin films as compared to undoped TiO₂ and results in p-type electrical conduction. Resistivity of Ti-V oxides thin films was found at the order of 10⁵ Ω cm. Optical measurements have shown the average transmission coefficient of about 73% in the visible spectral range and that the position of fundamental absorption edge has been shifted by 40 nm towards the longer wavelength as compared to the undoped TiO₂. The results testified that the prepared Ti-V oxides thin films might be considered as a p-type transparent oxide semiconductors for future application in transparent electronics.     

Preparation and conductive properties of neodymium-doped lanthanum nickelate thin films by chemical solution deposition method

Neodymium-doped lanthanum nickelate (La_1 − xNd_xNiO₃, LNNO) thin films have been prepared on Si substrates by chemical solution deposition method. The effects of annealing temperature and the neodymium concentration on the structural and electrical properties of the thin films have been investigated. X-ray diffraction analysis showed that the LNNO thin films exhibited perovskite structure with (100) preferential orientation. The (100) orientation degree of the thin films changed with neodymium content; however, the resistivity of the thin films was not related to the degree of orientation. Field emission scanning electron microscopy observations confirmed that the films had a smooth surface and uniform thickness. The resistivity of the thin films annealed at 700 °C increased from 1.97 mΩ·cm to 5.35 mΩ·cm, with increasing neodymium doping amount from LaNiO₃ to La_0.6Nd_0.4NiO₃.     

Radio frequency sputter deposition of high-quality conductive and transparent ZnO:Al films on polymer substrates for thin film solar cells applications

Thick aluminum-doped zinc oxide films were deposited at substrate temperatures from 100 °C to room temperature on polyethylene terephthalate by radio frequency magnetron sputtering, varying the deposition parameters such as radio frequency power and working pressure.Structural, optical and electrical properties were analyzed using an x-ray diffractometer, a spectrophotometer and a four-point probe, respectively. Films were polycrystalline showing a strong preferred c-axis orientation (002). The best optical and electrical results were achieved using a substrate temperature of 100 °C. Furthermore, high transmittances close to 80% in the visible wavelength range were obtained for those films deposited at the lowest Argon pressure used of 0.2 Pa. In addition, resistivities as low as 1.1 × 10^− 3 Ω cm were reached deposited at a RF power of 75 W. Finally, a comparison of the properties of the films deposited on polymer and glass substrates was performed, obtaining values of the figure of merit for the films on polymer comparable to those obtained on glass substrates, 17,700 Ω^− 1 cm^− 1 vs 14,900 Ω^− 1 cm^− 1, respectively.     

Structural properties of low-temperature grown ZnO thin films determined by X-ray diffraction and X-ray absorption spectroscopy

The epitaxial growth of ZnO thin films on Al₂O₃ (0001) substrates have been achieved at a low-substrate temperature of 150 °C using a dc reactive sputtering technique. The structures and crystallographic orientations of ZnO films varying thicknesses on sapphire (0001) were investigated using X-ray diffraction (XRD). We used angle-dependent X-ray absorption near-edge structure (XANES) and extended X-ray absorption fine structure (EXAFS) spectroscopy to examine the variation of local structure. The XRD data showed that the crystallinity of the film is improved as the film thickness increases and the strain is fully released as the film thickness reached about 800 Å. The Zn K-edge XANES spectra of the ZnO films have a strong angle-dependent spectral feature resulting from the preferred c-axis orientation. The wurtzite structure of the ZnO films was explicitly shown by the XRD and EXAFS analysis. The carrier concentration, Hall mobility and resistivity of the 800 Å-thick ZnO film were 1.84 × 10¹⁹ cm^− 3, 24.62 cm²V^− 1s^− 1, and 1.38 × 10^− 2 Ω cm, respectively.     

Deposition of silicon nitride thin films by hot-wire CVD at 100 °C and 250 °C

Silicon nitride thin films for use as passivation layers in solar cells and organic electronics or as gate dielectrics in thin-film transistors were deposited by the Hot-wire chemical vapor deposition technique at a high deposition rate (1-3 ?/s) and at low substrate temperature. Films were deposited using NH₃/SiH₄ flow rate ratios between 1 and 70 and substrate temperatures of 100 °C and 250 °C. For NH₃/SiH₄ ratios between 40 and 70, highly transparent (T ~ 90%), dense films (2.56-2.74 g/cm³) with good dielectric properties and refractive index between 1.93 and 2.08 were deposited on glass substrates. Etch rates in BHF of 2.7 ?/s and < 0.5 ?/s were obtained for films deposited at 100 °C and 250 °C, respectively. Films deposited at both substrate temperatures showed electrical conductivity ~ 10^− 14 Ω^− 1 cm^− 1 and breakdown fields > 10 MV cm^− 1.     

p-type doping of ZnO by means of high-density inductively coupled plasmas

A custom-designed inductively coupled plasma assisted radio-frequency magnetron sputtering deposition system has been used to fabricate N-doped p-type ZnO (ZnO:N) thin films on glass substrates from a sintered ZnO target in a reactive Ar + N₂ gas mixture. X-ray diffraction and scanning electron microscopy analyses show that the ZnO:N films feature a hexagonal crystal structure with a preferential (002) crystallographic orientation and grow as vertical columnar structures. Hall effect and X-ray photoelectron spectroscopy analyses show that N-doped ZnO thin films are p-type with a hole concentration of 3.32 × 10¹⁸ cm^− 3 and mobility of 1.31 cm² V^− 1 s^− 1. The current-voltage measurement of the two-layer structured ZnO p-n homojunction clearly reveals the rectifying ability of the p-n junction. The achievement of p-type ZnO:N thin films is attributed to the high dissociation ability of the high-density inductively coupled plasma source and effective plasma-surface interactions during the growth process.     

Nanocrystalline silicon films with high conductivity and the application for PIN solar cells

Intrinsic nanocrystalline silicon films (nc-Si:H) were prepared by plasma enhanced chemical vapor deposition (PECVD) method. Films’ microstructures and characteristics were studied with Raman spectroscopy and Atom Force Microscope (AFM). The electronic conductivity of nc-Si:H films was found to be 4.9×10⁰Ω⁻¹ cm⁻¹, which was one order of magnitude higher thanthe reported 10⁻³-10⁻¹ Ω⁻¹ cm⁻¹. And PIN solar cells with nc-Si:H film as intrinsic thin-layer (ITO/n⁺-nc-Si:H/i-nc-Si:H/p-c-Si/Ag) were researched. The cell's performances were measured, the open-circuit voltage V_oc was 534.7 mV, short-circuit current I_sc was 49.24 mA (3 cm²) and fill factor FF was 0.4228.     

Aluminum doped silicon carbide thin films prepared by hot-wire CVD: Investigation of defects with electron spin resonance

Al-doped p-type μc-SiC:H is prepared in a wide range of HWCVD preparation parameters like Al-doping ratio, deposition pressure, substrate and filament temperatures. We investigate the structural and electrical properties, and focus on identification of paramagnetic defect states by electron spin resonance (ESR). Nominally undoped μc-SiC:H is of a high n-type conductivity (σ_D = 10^− 6-10^− 1 S/cm) and shows a narrow central ESR line (g ≈ 2.003, peak-to-peak linewidth ?H_pp ≈ 4 G) with two pairs of satellites and a spin density N_S = 10¹⁹ cm^− 3. Al-doping results in the compensation of dark conductivity to as low as σ_D = 10^− 11 S/cm and at higher doping concentrations to effective p-type material. Increase of Al-doping results in reduction of crystallinity (I_C^IR), ESR line shifts to g ≈ 2.01 and becomes as broad as ?H_pp ≈ 30 G, not unlike to the resonance of singly occupied paramagnetic valence band tail states in a-Si:H. ESR spectrum of highly crystalline Al-doped μc-SiC:H however has a g-value very close to undoped μc-SiC:H. Electron spin density in compensated material decreases to 5 × 10¹⁷ cm^− 3 before it increases again for the highly doped material.     

Formation and characterization of thin films from phthalocyanine complexes: An electrosynthesis study using the atomic-force microscope

(μ-Cyano)(phthalocyaninato)metal(III) [PcMCN]_n species with a central transition metal ion, such as Fe(III) and Co(III), were used to prepare molecular films on a highly oriented pyrolytic graphite electrode substrate by using the cyclic voltammetry technique. In order to investigate the influence of the ligand on the film properties, 1,8-dihydroxyanthraquinone and 2,6-dihydroxyanthraquinone as bivalent ligands were employed. The structure of the molecular materials was analyzed by infrared spectroscopy. The in situ film formation, texture, composition and conductivity of each film were further investigated using atomic force microscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy and the four-probe technique, respectively. The [PcMCN]_n complexes provided conductive films with an electrical conductivity of 1 × 10^− 6 Ω^− 1 cm^− 1 at 298 K.     

ZnO thin films prepared by atomic layer deposition and rf sputtering as an active layer for thin film transistor

Recently, the application of ZnO thin films as an active channel layer of transparent thin film transistor (TFT) has become of great interest. In this study, we deposited ZnO thin films by atomic layer deposition (ALD) from diethyl Zn (DEZ) as a metal precursor and water as a reactant at growth temperatures between 100 and 250 °C. At typical growth conditions, pure ZnO thin films were obtained without any detectable carbon contamination. For comparison of key film properties including microstructure and chemical and electrical properties, ZnO films were also prepared by rf sputtering at room temperature. The microstructure analyses by X-ray diffraction have shown that both of the ALD and sputtered ZnO thin films have (002) preferred orientation. At low growth temperature T_s ≤ 125 °C, ALD ZnO films have high resistivity (> 10 Ω cm) with small mobility (< 3 cm²/V s), while the ones prepared at higher temperature have lower resistivity (< 0.02 Ω cm) with higher mobility (> 15 cm²/V s). Meanwhile, sputtered ZnO films have much higher resistivity than ALD ZnO at most of the growth conditions studied. Based upon the experimental results, the electrical properties of ZnO thin films depending on the growth conditions for application as an active channel layer of TFT were discussed focusing on the comparisons between ALD and sputtering.     

Large-sized-mismatched group-V element doped ZnO films fabricated on silicon substrates by pulsed laser deposition

Pulsed laser deposition has been utilized to synthesize impurity-doped ZnO thin films on silicon substrate. Large-sized-mismatched group-V elements (A^V) including P, As, Sb and Bi were used as dopants. Hall effect measurements show that hole concentration in the order of 10¹⁶-10¹⁸ cm⁻³, resistivity in the range of 10-100 Ω cm, Hall mobility in the range of 10-100 cm²/Vs were obtained only for ZnO:As and ZnO:Bi thin films. X-ray diffraction measurements reveal that the films possess polycrystallinity or nanocrystallinity with ZnO (002) preferred orientation. Guided by X-ray photoemission spectroscopy analyses and theoretical calculations for large-sized-mismatched group-V dopant in ZnO, the A_Zn^V-2V_Zn complexes are believed to be the most possible acceptors in the p-type A^V-doped ZnO thin films.