Condensation heat transfer and pressure drop of HFC-134a in a helically coiled concentric tube-in-tube heat exchanger

The two-phase heat transfer coefficient and pressure drop of pure HFC-134a condensing inside a smooth helically coiled concentric tube-in-tube heat exchanger are experimentally investigated. The test section is a 5.786 m long helically coiled double tube with refrigerant flowing in the inner tube and cooling water flowing in the annulus. The inner tube is made from smooth copper tubing of 9.52 mm outer diameter and 8.3 mm inner diameter. The outer tube is made from smooth copper tubing of 23.2 mm outer diameter and 21.2 mm inner diameter. The heat exchanger is fabricated by bending a straight copper double-concentric tube into a helical coil of six turns. The diameter of coil is 305 mm. The pitch of coil is 35 mm. The test runs are done at average saturation condensing temperatures ranging between 40 and 50 °C. The mass fluxes are between 400 and 800 kg m⁻² s⁻¹ and the heat fluxes are between 5 and 10 kW m⁻². The pressure drop across the test section is directly measured by a differential pressure transducer. The quality of the refrigerant in the test section is calculated using the temperature and pressure obtained from the experiment. The average heat transfer coefficient of the refrigerant is determined by applying an energy balance based on the energy rejected from the test section. The effects of heat flux, mass flux and, condensation temperature on the heat transfer coefficients and pressure drop are also discussed. It is found that the percentage increase of the average heat transfer coefficient and the pressure drop of the helically coiled concentric tube-in-tube heat exchanger, compared with that of the straight tube-in-tube heat exchanger, are in the range of 33–53% and 29–46%, respectively. New correlations for the condensation heat transfer coefficient and pressure drop are proposed for practical applications.     

Investigation of heat transfer and pressure drop in a concentric heat exchanger with snail entrance

In this study, in order to increase heat transfer in concentric double-pipe heat exchangers by passive method, snail which is mounted at inlet of the inner pipe and assumed as a swirl generator was used. In the experimental set-up, cold air in ambient conditions was passed through the inner pipe while hot water was flowing through the annulus. The effects of a snail on the heat transfer and pressure drop were investigated for parallel and counter-flow, and obtained Nusselt numbers (Nu) were compared with those found, using a standard correlation such as Dittus–Boelter equation given for axial flows in smooth pipes. The results were correlated in the form of Nusselt number as a function of Reynolds number, Prandtl number and the swirling angle. An augmentation of up to 120% in Nusselt number was obtained in the swirl flow for counter-flow and 45° swirling angle. Though the swirl flow effect of the snail caused some increase in pressure drop, this effect was unimportant compared with the improvement in heat transfer capacity.     

Evaporation heat transfer and pressure drop of refrigerant R-134a in a small pipe

An experiment was carried out to investigate the characteristics of the evaporation heat transfer and pressure drop for refrigerant R-134a flowing in a horizontal small circular pipe having an inside diameter of 2.0 mm. The data are useful in designing more compact and effective evaporators for various refrigeration and air conditioning systems. The effects of the imposed wall heat flux, mass flux, vapor quality and saturation temperature of R-134a on the measured evaporation heat transfer and pressure drop were examined in detail. When compared with the data for larger pipes (D_i ≥ 8.0 mm) reported in the literature, the evaporation heat transfer coefficient for the small pipe considered here is about 30–80% higher for most situations. Moreover, we noted that in the small pipe the evaporation heat transfer coefficient is higher at a higher imposed wall heat flux except in the high vapor quality region, at a higher saturation temperature, and at a higher mass flux when the imposed heat flux is low. In addition, the measured pressure drop is higher for increases in the mass flux and imposed wall heat flux. Based on the present data, empirical correlations were proposed for the evaporation heat transfer coefficients and friction factors.     

Turbulent heat transfer in a horizontal helically coiled tube

An experiment has been conducted in detail to study the turbulent heat transfer in horizontal helically coiled tubes over a wide range of experimental parameters. We found that the enhancement of heat transfer in the coils results from the effects of turbulent and secondary flows. With Reynolds number increasing to a high level, the contribution of the secondary flow becomes less to enhance heat transfer, and the average heat transfer coefficient of the coil is closer to that in straight tubes under the same conditions. The local heat transfer coefficients are not evenly distributed along both the tube axis and the periphery on the cross section. The local heat transfer coefficients on the outside are three or four times those on the inside, which is half of the average heat transfer. A correlation is proposed to describe the distribution of the heat transfer coefficients at a cross section. The average cross-section heat transfer coefficients are distributed along the tube axis. The average value at the outlet section should not be taken as the average heat transfer coefficient. © 1999 Scripta Technica, Heat Trans Asian Res, 28(5): 395–403, 1999     

Thermal and hydraulic characteristics of nanofluid flow in a helically coiled tube heat exchanger

The effects of using different geometrical parameters with the combination of nanofluid on heat transfer and fluid flow characteristics in a helically coiled tube heat exchanger (HCTHE) are numerically investigated. A CuO nanoparticle with a diameter of 25 nm dispersed in water with a particle concentration of 4% was used as the working fluid. The three dimensional governing equations (continuity, momentum and energy) along with the boundary conditions are solved using the finite volume method (FVM). The mass flow rate of water in the annulus was kept constant and the nanofluid flow rate in the inner tube was varied. The effect of flow configuration (parallel and counter) was also examined in this study. The performance of the HCTHE was evaluated in terms of Nusselt number, heat transfer rate, pressure drop, effectiveness and performance index. The results reveal that certain geometrical parameters such as the helix radius and inner tube diameter do affect the performance of the HCTHE under laminar flow conditions. It is also found that counter-flow configuration produced better results as compared to parallel-flow configuration.     

Comparative analysis of heat transfer and pressure drop in helically segmented finned tube heat exchangers

Four different semi-empirical models of heat transfer and pressure drop for helically segmented finned tubes in staggered layout were analyzed. The performance of a Helically Segmented Finned Tubes Heat Exchanger on an industrial scale was obtained and the predictions were compared with experimental data. The method used for thermal analysis is the Logarithmic Mean Temperature Difference (LMTD). Comparisons between predictions and experimental data show a precision greater than 95% in heat transfer for a combination between the Kawaguchi and Gnielinski models at a flue gas Reynolds number, based on the outside bare tube, of about 10,000. In the case of pressure drop, there is a precision of approximately 90% for the Weierman model at a Reynolds number, based on the outside bare tube, of about 10,000. And so, the results show that the best flow regime in which heat transfer and pressure drop are optimum, is for a Reynolds number (based on the outside bare tube) of about 10,000.     

Single-phaseexperimental analysis of heat transfer in helically finned heat exchanger

A methodology for designing helically serrated finned tube heat exchanger based on the logarithmic Mean Temperature Difference (LMTD) method is validated with experimental tests. The method uses semi-empirical correlations for calculating convective coefficients both inside and outside staggered tube bundles. Equipment was designed, built, and installed in a paper factory in order to validate the methodology. Comparisons between predictions and experimental data show a precision of approximately 96% in heat transfer and approximately 90% in pressure drop for Reynolds numbers upper to 10,000.     

Effect of interbaffle spacing on heat transfer and pressure drop in a shell-and-tube heat exchanger

Experiments have been performed to determine the response of the heat (mass) transfer and pressure drop on the shell side of a shell-and-tube heat exchanger to changes in the interbaffle spacing. Per-tube, per-row and per-compartment heat (mass) transfer coefficients were obtained by means of the naphthalene sublimation technique, all for the fully developed regime. Pressure distribution measurements were made throughout the heat exchanger, and the pattern of fluid flow was visualized with the aid of the oil-lampblack technique. The greatest sensitivity of the per-tube heat transfer coefficient to the interbaffle spacing occurred at the tubes situated in the inflow window of a compartment, where higher coefficients (by about 15%) were encountered for larger interbaffle spacings. In the crossflow zone, the per-tube transfer coefficients corresponding to the smaller interbaffle spacing exceeded those for the larger interbaffle spacing by about 5%, and similarly in the baffle-adjacent row in the outflow window of the compartment. The other rows in the outflow window were ambivalent about the effects of interbaffle spacing. Owing to cancellations among the aforementioned per-tube responses, the compartment-average transfer coefficients were virtually unaffected by the spacing. The per-compartment pressure drop decreased as the interbaffle spacing decreased, but for a fixed streamwise length, the pressure drop was slightly larger for smaller spacings. The experimental results were compared with the predictions of the Tinker and Delaware Project design methods.     

Turbulent heat transfer enhancement in a heat exchanger using helically corrugated tube

The augmentation of convective heat transfer in a single-phase turbulent flow by using helically corrugated tubes has been experimentally investigated. Effects of pitch-to-diameter ratio (P/D_H = 0.18, 0.22 and 0.27) and rib-height to diameter ratio (e/D_H = 0.02, 0.04 and 0.06) of helically corrugated tubes on the heat transfer enhancement, isothermal friction and thermal performance factor in a concentric tube heat exchanger are examined. The experiments were conducted over a wide range of turbulent fluid flow of Reynolds number from 5500 to 60,000 by employing water as the test fluid. Experimental results show that the heat transfer and thermal performance of the corrugated tube are considerably increased compared to those of the smooth tube. The mean increase in heat transfer rate is between 123% and 232% at the test range, depending on the rib height/pitch ratios and Reynolds number while the maximum thermal performance is found to be about 2.3 for using the corrugated tube with P/D_H = 0.27 and e/D_H = 0.06 at low Reynolds number. Also, the pressure loss result reveals that the average friction factor of the corrugated tube is in a range between 1.46 and 1.93 times over the smooth tube. In addition, correlations of the Nusselt number, friction factor and thermal performance factor in terms of pitch ratio (P/D_H), rib-height ratio (e/D_H), Reynolds number (Re), and Prandtl number (Pr) for the corrugated tube are determined, based on the curve fitting of the experimental data.     

Numerical study on heat transfer and pressure drop characteristics of fluid flow in an inserted coiled tube type three fluid heat exchanger

The paper presents numerical investigations of a three fluid heat exchanger (TFHE), which is an improvement on the double pipe heat exchanger, where a helical tube is inserted in the annular space between two straight pipes. The helical tube side fluid, that is, hot water continuously transfers heat to the outer annulus side fluid and innermost tube side fluid. The heat transfer and pressure drop characteristics of the TFHE are assessed for different flow rates and inlet temperatures. With an increment in the volumetric flow rate of the helical tube side fluid and outer annulus side fluid, the overall heat transfer coefficient increases, and the effectiveness decreases for heat transfer from the helical tube side fluid to outer annulus side fluid in both parallel flow and counter flow configurations. It is also observed that with increment in the helical tube side fluid inlet temperature, the overall heat transfer coefficient and effectiveness increases for heat transfer from the helical tube side fluid to outer annulus side fluid in both flow configurations. The parameter, JF factor, has been proposed to evaluate the thermohydraulic behavior of the TFHE, where it is obtained that the behavior of the TFHE is better at a lower helical tube side fluid velocity and higher outer annulus side fluid velocity.     

板式换热器传热和阻力特性的实验研究

利用搭建的液-液型板式换热器试验平台,根据实验数据运用定性雷诺数法拟合出传热关联式,找出Nu与摩擦因子f之间的通用关系式,为板式换热器的设计计算提供了依据。运用传热量与功率的消耗比来评价板式换热器的性能,找出了影响其性能的主要因素,进一步澄清了单纯依靠提高流速来增加传热性能是不经济的。     

Exergy transfer effectiveness on heat exchanger for finite pressure drop

In this paper, exergy transfer effectiveness is defined to describe the performance of heat exchangers operating above/below the surrounding temperature with/without finite pressure drop. It is discussed systemically that the effects of heat transfer units number, the ratio of the heat capacity of cold fluids to that of hot fluids and flow patterns on exergy transfer effectiveness of heat exchangers. Furthermore, the results of exergy transfer effectiveness with a finite pressure drop are compared with those without pressure drop when different objective media, such as ideal gas and incompressible liquid, etc. are applied. The detailed comparisons of the exergy transfer effectiveness with heat transfer effectiveness are also performed for the parallel flow, counter flow and cross flow heat exchangers operating above/below the surrounding temperature.     

Numerical prediction of turbulent flow and heat transfer in helically coiled pipes

Computational results were obtained for turbulent flow and heat transfer in curved pipes, representative of helically coiled heat exchangers. Following a grid refinement study, grid independent predictions from alternative turbulence models (k–?, SST k–ω and RSM–ω) were compared with DNS results and experimental pressure drop and heat transfer data. Using the SST k–ω and RSM–ω models, pressure drop results were in excellent agreement with literature data and the Ito correlation. For heat transfer, the literature is not comparably complete or accurate, but a satisfactory agreement was obtained in the range of available data. Unsatisfactory results, both for pressure drop and heat transfer, were given by the k–? model with wall functions. Following the validation study, the RSM–ω model was used to compute friction coefficients and Nusselt numbers in the range Re = 1.4·10⁴–8·10⁴, Pr = 0.7–5.6 and δ (coil curvature) = 3·10^?3–0.3. Power-law correlations were found unsuitable to fit the Re-, Pr- and δ-dependence of the Nusselt number, while the use of a properly formulated momentum-heat transfer analogy collapsed all results with high accuracy.     

Heat transfer and pressure drop performance of twisted oval tube heat exchanger

Twisted oval tube heat exchanger is a type of heat exchanger that aims at improving the heat transfer coefficient of the tube side and also decreasing the pressure drop of the shell side. In the present work, tube side and shell side heat transfer and pressure drop performances of a twisted oval tube heat exchanger has been experimentally studied. The tube side study shows that the tube side heat transfer coefficient and pressure drop in a twisted oval tube are both higher than in a smooth round tube. The shell side study shows that the lower the modified Froude number Fr_M, the higher the shell side heat transfer coefficient and pressure drop. In order to comparatively analyze its shell side performance of the heat exchanger, a rod baffle heat exchanger with similar size of the twisted oval tube heat exchanger is designed and its performance is calculated with Gentry's method. The comparative study shows that the heat transfer coefficient of the twisted oval tube heat exchanger is higher and the pressure drop is lower than the rod baffle heat exchanger. In order to evaluate the overall performance of the twisted oval tube heat exchanger, a performance evaluation criterion considering both the tube side and shell side performance of a heat exchanger is proposed and applied. The analyze of the overall performance of the twisted oval tube shows that the twisted oval tube heat exchangers works more effective at low tube side flow rate and high shell side flow rate.     

Single-phase heat transfer and pressure drop in the micro-fin tubes with coiled wire insert

The heat transfer characteristics and the pressure drop of the horizontal double pipes with and without coiled wire insert are investigated. The inner and outer diameters of the micro-fin tube are 8.92 and 9.52 mm, respectively. The coiled wire is fabricated by bending a 1-mm-diameter iron wire into the coil wire with coil diameter of 7.80 mm. Cold and hot water are used as working fluids in shell side and tube side, respectively. The test runs are performed at the cold and hot water mass flow rates ranging between 0.01 and 0.07 kg/s and between 0.04 and 0.08 kg/s, respectively. The inlet cold and hot water temperatures are between 15 and 20 °C and between 40 and 45 °C, respectively. The results obtained from the micro-fin tube with coiled wire insert are compared with those obtained from the smooth and micro-fin tubes.     

Analysis of heat transfer and pressure drop characteristics in an offset strip fin heat exchanger

A steady-state three-dimensional numerical model was used to study the heat transfer and pressure drop characteristics of an offset strip fin heat exchanger. Water was the heat transfer medium, and the Reynolds number Re_dh ranged from 10 to 3500. Variations in the Fanning friction factor f and the Colburn heat transfer factor j relative to Re_dh were observed. General correlations for the f and j factors were derived, and these could be used to analyze fluid flow and heat transfer characteristics of offset strip fins in the laminar, transition, and turbulent regions. Finally, three performance criteria (j/f, j/f^1/3, and JF) were adopted, and the best performance criteria for the cases Pr = 7 and Pr = 50 were chosen to be JF and j/f^1/3, respectively.     

Condensation heat transfer and pressure drop characteristics of R-134a in an annular helical pipe

Condensation heat transfer and pressure drop data of R-134a in annular helical pipes is of significant importance to the effective design and reliable operation of helical pipe heat exchangers for refrigeration, air-conditioning, and many other applications. This paper presents the experimental investigation on condensation heat transfer and pressure drop characteristics of R-134a in an annular helical pipe. The average condensation heat transfer coefficients and pressure drops were experimentally determined for R-134a at three different saturated temperatures (35 °C, 40 °C, and 46 °C). The experimental results are compared with the data available in the literature for helical and straight pipes.     

Influence of transverse vibrations on convective heat transfer in parallel flow tube-in-tube heat exchanger

Tube-in-tube heat exchangers are widely used in food processing industries and wastewater treatment for both heating and cooling. Enhancement techniques namely active, passive, and compound are developed to reduce the thermal resistance in heat exchangers by improving convective heat transfer with or without increase in surface area. The present experimental study is aimed at analyzing the influence of vibrations on the convective heat transfer of a parallel flow tube-in-tube heat exchanger. The heat exchanger is placed in horizontal position and is subjected to transverse vibrations under turbulent fluid flow conditions. Experiments were performed at four frequencies (20, 40, 60, and 100 Hz), three amplitudes (1, 2, and 3 m/s²), and three vibration generator positions along its length, in the Reynolds number range of 10 710 to 21 420. An enhancement in Nusselt number is found with vibration than without vibration throughout the entire range of Reynolds numbers. A maximum enhancement of 33% at 40 Hz frequency, 3 m/s² amplitude, and vibration generator position at three-fourth of the tube length was observed. Empirical correlations are developed for Nusselt number to determine the heat transfer coefficient with vibration with an error of $\pm$10%.     

A heat transfer correlation of flow boiling in micro-finned helically coiled tube

Two main mechanisms, nucleate boiling and convective boiling, are widely accepted for in-tube flow boiling. Since the active nuclei on the heated wall are dominant for nucleate boiling and flow pattern governs the convective boiling, the heat transfer coefficient is strongly influenced by the wall heat flux, mass flux and vapor quality, respectively. In practical industrial applications, for example, the evaporators in refrigeration, forced convective evaporation is the dominant process and high heat transfer efficiency can be obtained under smaller temperature difference between wall and liquid. Therefore, it is of importance to develop a correlation of convective boiling heat transfer with a good accuracy. In this paper, a new kind of micro-finned helically coiled tube was developed and the flow boiling heat transfer characteristics were experimentally studied with R134a. Based on the analysis of the mechanisms of flow boiling, heat transfer correlations of the specific micro-finned helically coiled tubes are obtained.     

Experimental shell-side heat transfer and pressure drop in gas flow for spiral-wound LNG heat exchanger

A test plant has been constructed for measurements of local heat-transfer coefficients and frictional pressure drops on the shell side of spiral-wound LNG heat exchangers. Measurements have been performed with gas flow, liquid film flow and two-phase shear flow. This paper focuses on the measurements and the results from the gas flow measurements. 221 gas flow heat-transfer measurements and 80 gas flow frictional pressure drop measurements have been performed at a Re-number range of 5000-170 000 with nitrogen, methane, ethane and methane/ethane mixture as test fluids.