Cationic Micelles Modulated in the Presence of α,ω-Alkanediols: A SANS,NMR and Conductometric Study

The solution behavior of a typical cationic surfactant, tetradecyltrimethylammonium bromide, in mixed solvent systems composed of water and varying concentrations of α,ω-alkanediols; 1,2-ethanediol (ED), 1,4-butanediol (BD), 1,6-hexanediol (HD) and 1,8-octanediol (OD) was examined via electrical conductance measurements, ¹³C-NMR spectroscopy and small angle neutron scattering (SANS) measurements. The critical micelle concentration (CMC) values and degree of counterion dissociation (α) indicate that both ED and BD oppose micellization, whereas HD and OD enhance micelle formation. Changes in the ¹³C-NMR chemical shifts (∆δ values) reveal that the short chain diols reside almost exclusively in the bulk phase and hence, affect the formation of micelles by altering the solvent properties in the bulk of the solution, whereas HD and OD partition between the pseudomicellar phase and the bulk phase. SANS studies indicated that both the micellar size and aggregation number (N _agg) decrease in the presence of all diols. ED and BD behave like cosolvents and increase the α and CMC values and decrease N _agg. We note that the effect of HD and OD on the properties of the micelles is concentration dependent; at low concentrations, these diols interact with the micelles and behave as cosurfactants (as evidenced by the trends in the micellar properties), while at higher concentrations, they enhance the surfactant solubility and behave as a cosolvent.     

Investigation of the properties of decaoxyethylene <Emphasis Type="Italic">n</Emphasis>-dodecyl ether,C<Subscript>12</Subscript>E<Subscript>10</Subscript>, in the aqueous sugar-rich region

Interfacial, thermodynamic, and morphological properties of decaoxyethylene n-dodecylether [CH₃ (CH₂)₁₁(OCH₂CH₂)₁₀OH](C₁₂E₁₀) in aqueous solution were analyzed by tensiometric, viscometric, proton nuclear magnetic resonance (NMR), and small-angle neutron scattering (SANS) techniques. Dynamic and structural aspects at different temperatures in the absence and presence of sugars at different concentrations were measured. Critical micelle concentrations (CMC) were determined by surface tension measurements in the presence of ribose, glucose, and sucrose. The heat capacity (ΔC _p.m.), transfer enthalpy (ΔH _m.tr.), transfer heat capacities (ΔC _p.m.tr.), micellization constant (K _m ), Setchenow constant (K _S ^N ), and partition coefficient (q) were determined and discussed as an extension of the usual thermodynamic quantities of micellization and adsorption at the air-water interface. An enthalpy-entropy compensation effect was observed with an isostructural temperature (T _c ) of about 310 K for both micellization and interfacial adsorption. SANS measurements were taken to elucidate structural information, viz., aggregation number (N _agg), shape, size, and number density (N _m ) on C₁₂E₁₀ micelles in D₂O at different concentrations of sugars (0.05, 0.02, 0.3, and 0.5 M) and temperatures (30, 45, and 60°C). Intrinsic viscosity gave the hydrated micellar volume (V _h ), volume of the hydrocarbon core (V _c ), and volume of the palisade layer of the oxyethylene (OE) unit (V _OE). SANS, as well as rheological data, supported the formation of nonspherical micelles with or without sugars. By SANS, we also observed that at the studied temperature intervals, oblate ellipsoid micelles changed into prolate ellipsoids and the number density of micelles decreased with an increase in temperature both in the presence and in the absence of sugars and also on increasing the concentration of sugars. Proton NMR showed a change in chemical shift of the OE group of micelles above the CMC. We also studied the phase separation of C₁₂E₁₀ by sugars in cloud point measurements.     

Sans Study of Reverse Micelles Formed upon the Extraction of Inorganic Acids by TBP in n‐Octane

Small‐angle neutron scattering (SANS) data for n‐octane solutions of TBP loaded with progressively larger amounts of HNO₃, HClO₄, H₂SO_4, and H₃PO₄ up to and beyond the LOC (limiting organic concentration of acid) condition, were interpreted using the Baxter model for hard spheres with surface adhesion. The coherent picture of the behavior of the TBP solutions derived from the SANS investigation discussed in this paper confirmed our recently developed model for third phase formation. This model analyses the features of the scattering data in the low Q region as arising from van der Waals interactions between the polar cores of reverse micelles. Our SANS data indicated that the TBP micelles swell when acid and water are extracted into their polar core. The swollen micelles have critical diameters ranging from 15 to 22 Å, and polar core diameters between 10 and 15 Å, depending on the specific system. At the respective LOC conditions, the TBP weight‐average aggregation numbers are ～4 for HClO₄, ～6 for H₂SO₄, ～7 for HCl, and ～10 for H₃PO₄. The comparison between the behavior of HNO₃, a non‐third phase forming acid, and the other acids provided an explanation of the effect of the water molecules present in the polar core of the micelles on third phase formation. The thickness of the lipophilic shell of the micelles indicated that the butyl groups of TBP lie at an angle of ～25 degrees relative to a plane tangent to the micellar core. The critical energy of intermicellar attraction, U(r), was about ?2 k_BT for all the acids investigated. This value is the same as that reported in our previous publications on the extraction of metal nitrates by TBP, confirming that the same mechanism and energetics are operative in the formation of a third phase, independent of whether the chemical species extracted are metal nitrate salts or inorganic acids.     

Conformation of oligo(ethylene glycol) grafted polystyrene in dilute aqueous solutions

Temperature induced conformational changes of poly(p-oligo(ethylene glycol) styrene) (POEGS) in aqueous solutions were investigated by small angle neutron scattering (SANS), neutron transmission and dynamic light scattering (DLS). The molecular weight of the polymer studied was 9400 g/mol with a polydispersity index of 1.18 and each repeat unit of the polymer had four ethylene glycol monomer segments. The polymer was water soluble due to the hydrophilicity of the OEG side chains and these solutions showed lower critical solution temperature (LCST) depending on the concentration of the polymer. Measurements of solution behavior were made as a function of temperature in the range of 25-55 °C for three polymer concentrations (0.1 wt%, 0.3 wt%, and 1.8 wt%). Neutron transmission measurements were used to monitor the amount of polymer which precipitated or remained in solution above the cloud point temperature (T_CP). DLS revealed the presence of large clusters in all solutions both below and above T_CP while SANS provided information on the structure and interactions between individual chains. It was found that in the homogeneous region below T_CP the shape of individual polymers in solution was close to ellipsoidal with the dimensions R_a = 37 Å and R_b = 14 Å and was virtually independent of temperature. The SANS data taken for the most concentrated solution studied (1.8 wt%) were fit to the ellipsoidal model with attractive interactions which were approximated by the Ornstein-Zernike function with a temperature-dependent correlation length in the range of 24-49 Å. The collapse of individual polymers to spherical globules with the radius of 15 Å above T_CP was observed.     

Preparation and characterization of poly(vinyl chloride)/polystyrene/poly(ethylene glycol) hollow‐fiber ultrafiltration membranes

Hollow‐fiber ultrafiltration (UF) membranes were prepared from blends of poly(vinyl chloride) (PVC) and polystyrene (PS) with a dry/wet phase inversion method. Poly(ethylene glycol) (PEG) and N,N‐dimethylacetamide were used as the additive and solvent, respectively. The effects of the PEG concentration in the dope solution as an additive on the cross sections and inner and outer surface morphologies, permeability, and separation performance of the hollow fibers were examined. The mean pore size, pore size distribution, and mean roughness of both the inner and outer surfaces of the produced hollow fibers were determined by atomic force microscopy. Also, the mechanical properties of the hollow‐fiber membranes were investigated. UF experiments were conducted with aqueous solutions of poly(vinyl pyrrolidone) (PVP; K‐90, M_w = 360 kDa). From the results, we found that the PVC/PS hollow‐fiber membranes had two layers with a fingerlike structure. These two layers were changed from a wide and long to a thin and short morphology with increasing PEG concentration. A novel and until now undescribed shape of the nodules in the outer surfaces, which was denoted as a sea‐waves shape, was observed. The outer and inner pore sizes both increased with increasing PEG concentration. The water permeation flux of the hollow fibers increased from 104 to 367 L m^?2 h^?1 bar^?1) at higher PEG concentrations. The PVP rejection reached the highest value at a PEG concentration of 4 wt %, whereas at higher values (from 4 to 9 wt %), the rejection decreased. The same trend was found also for the tensile stress at break, Young's modulus, and elongation at break of the hollow fibers. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 989‐1004, 2013     

Small‐Angle Neutron Scattering Study of Plutonium Third Phase Formation in 30% TBP/HNO3/Alkane Diluent Systems

Abstract

Third phase formation in the extraction of Pu(IV) nitrate by 30% tri‐n‐butyl phosphate (TBP) dissolved in n‐dodecane or in the highly branched diluent hydrogenated polypropylene tetramer (HPT), which may also be known as 4,4 dipropyl heptane or tétrapropylène hydrogéné, was investigated through small‐angle neutron scattering (SANS) measurements. The SANS data were interpreted using the Baxter model for hard‐spheres with surface adhesion. According to this model, the increase in scattering intensity observed when increasing amounts of Pu(NO₃)₄ are extracted into the organic phase, is due to interactions between small reverse micelles containing three to five TBP molecules. In n‐dodecane, the micelles interact through attractive forces between their polar cores with a potential energy of up to ?2.6 k_BT. This strong intermicellar attraction leads to organic phase splitting with the separation of most of the solutes of the original organic phase into a distinct phase containing interspersed layers of n‐dodecane. When HPT is the diluent, the intermicellar attraction energy calculated from the SANS data is much lower, and no third phase formation is observed under comparable chemical conditions. However, when a significant amount of the initial aqueous plutonium is in the form of plutonyl ions, PuO₂ ²⁺, the critical energy potential is reached even in HPT. A potential explanation of the effect of Pu(VI) involves the formation of a plutonyl trinitrato complex.     

Enhancement of the activity of papain in mixed reverse micellar systems in the presence of Tween80

An enhancement in the activity of papain (EC 3.4.22.2) was described in mixed reverse micellar systems containing Tween80 compared with those without Tween80. By the use of these media, the hydrolytic and synthesis activities of papain were investigated in detail, respectively for the hydrolysis of N‐α‐benzoyl‐L ‐arginine‐p‐nitroaniline (BNPNA) and the synthesis of the dipeptide Z‐Gly‐L ‐PheOMe (ZGPM). The reaction medium conditions (W₀, pH and Tween80 concentration) were optimized for both the hydrolytic and synthesis reactions. The results showed a pronounced increase in the papain activity when a moderate amount of Tween80 was added into sodium di‐2‐ethylhexylsulfosuccinate (AOT) or tetradecyltrimethylammonium bromide (TTAB) reverse micelles, either in the yield of dipeptide synthesis or in the initial rate of BNPNA hydrolysis. In addition, a mechanism to explain the enhancement of enzymatic activity was proposed according to the change of the optimal parameters in the mixed and non‐mixed reverse micellar systems, which is associated with the environmental polarity surrounding the solubilised enzyme molecules. © 2001 Society of Chemical Industry     

Synthesis of double‐hydrophilic poly(methylacrylic acid)–poly(ethylene glycol)–poly(methylacrylic acid) triblock copolymers and their micelle formation

The aim of the work reported was to synthesize a series of double‐hydrophilic poly(methacrylic acid)‐block‐poly(ethylene glycol)‐block‐poly(methacrylic acid) (PMAA‐b‐PEG‐b‐PMAA) triblock copolymers and to study their self‐assembly behavior. These copolymeric self‐assembly systems are expected to be potential candidates for applications as carriers of hydrophilic drugs. Bromo‐terminated difunctional PEG macroinitiators were used to synthesize well‐defined triblock copolymers of poly(tert‐butyl methacrylate)‐block‐poly(ethylene glycol)‐block‐poly(tert‐butyl methacrylate) via reversible‐deactivation radical polymerization. After the removal of the tert‐butyl group by hydrolysis, double‐hydrophilic PMAA‐b‐PEG‐b‐PMAA triblock copolymers were obtained. pH‐sensitive spherical micelles with a core–corona structure were fabricated by self‐assembly of the double‐hydrophilic PMAA‐b‐PEG‐b‐PMAA triblock copolymers at lower solution pH. Transmission electron microscopy and laser light scattering studies showed the micelles were of nanometric scale with narrow size distribution. Solution pH and micelle concentration strongly influenced the hydrodynamic radius of the spherical micelles (48–310 nm). A possible reason for the formation of the micelles is proposed. Copyright © 2010 Society of Chemical Industry     

Hydrophilic microporous PES membranes prepared by PES/PEG/DMAc casting solutions

Microporous poly(ether sulfones) (PES) membranes were prepared via phase inversion using poly (ethylene glycol) (PEG) as additive and N,N‐dimethylacetamide (DMAc) as solvent. Thermodynamic of the casting solutions was studied by coagulation value while precipitation rate was observed by light transmittance measurement. It was found that casting solution with PEG200 as additive was thermodynamically less stable than those with PEG400 and PEG600 as additive and easier to cause phase separation in exposure time. With the increase of PEG200 concentration, the casting solution became thermodynamically less stable and easier to cause phase separation in exposure time, but precipitation rate during immersion precipitation decreased because of the increased viscosities. ATR‐FTIR spectra and TGA curves showed that the membranes prepared using PEG200 as additive had less PEG residual than those of PEG400 and PEG600, but it showed better permeation performance than that prepared using PEG400 and PEG600 as additive. With the increase of PEG200 concentration from 30 to 70 wt %, the cross section structure changed from macrovoid to sponge‐like, micropores with a mean pore size around 0.1 μm began to form on the top surface. When the PEG200 concentration is 60 wt %, the pure water flux was 1845 L m^?2 h^?1 bar^?1, which is the highest value. As the PEG200 concentration increased from 30 to 60 wt %, the contact angles decreased from 82.1° to 58.2°. As the addition amount of PEG200 increased, the residual PEG made the prepared membranes more hydrophilic. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Solubilization,micellar transition and biocidal assay of loaded antioxidants in Tetronic® 1304 micelles

The current study scrutinizes the solubilization behaviour of pharmaceutically active antioxidants, namely hydrocinnamic acid (HCA), cinnamic acid (CA) and phenyl propiolic acid (PPA), in the micelles of polyethylene oxide‐polypropylene oxide (PEO‐PPO) based star‐block copolymer: Tetronic® 1304 (T1304). A correlation between the molecular orbital energy levels of PEO‐PPO units of T1304 and the active parts of the antioxidants are well explained using a simulation study. The antioxidants modulate core–shell micelles of T1304 with enhanced solubilization dependent on their unsaturation and hydrophobicity, as depicted from UV–visible spectroscopy. Antioxidants as an additive induce micellization in 5% w/v T1304 thereby modulating the phase behaviour, as indicated by the decrease in the cloud point. The cloud point results are well complemented by steady state fluorescence spectroscopy findings, depicting a decrease in critical micelle temperature due to the solubilization of antioxidants into the T1304 micelles. A significant difference between the hydrodynamic diameter (D_h) of unloaded and loaded polymer micelles with antioxidants is observed from dynamic light scattering, ensuring the solubilization of the antioxidants in T1304 micelles. These results can apparently be attributed to the interaction and the charge induced by the antioxidants on non‐ionic T1304 micelles which increase the micellar size. Furthermore, the role of unsaturation and hydrophobicity of the employed antioxidants in 5% T1304 demonstrates the solution viscosity (η) change as a function of temperature. In addition, small‐angle neutron scattering depicts the shape transition (spherical to ellipsoidal to polymersomes) with temperature. The antioxidant loaded 5% T1304 micellar systems exhibit brilliant biocidal activity against the tested microbes, suggesting their antimicrobial application. © 2019 Society of Chemical Industry     

Radiopaque epoxy resins

Transparent, X-ray contrast (radiopaque) epoxy resins were obtained by dissolving up to 25 wt % triphenylbismuth in the commercial epoxy resin prepolymers EPON-815, DER-330, DER-383, and DEN-431 which were then hardened with diethylenetriamine. The radiopacities of the mixtures were found to be proportional to the molar concentration of the radiopaque additive. The systems follow the relationship, R = R_o + (R_a ? R_o) V _a M_a where R, R_o, and R_a are the radiopacities of the mixture, the pure epoxy resin, and triphenylbismuth, respectively (expressed in mm aluminum/mm resin); M_a and V _a denote the molar concentration and molar volume of the bismuth compound. R_a for triphenylbismuth was found to be 7.4 ± 0.2 mm Al/mm resin; the average value of R_o for the four epoxies equals 0.16 ± 0.1 mm Al/mm resin. The amount of amine required to harden the radiopaque resins was far less for the epoxy novolac resin DEN-431 than for the three bisphenol-A based epoxies. The concentration of triphenylbismuth required to impart a radiopacity equivalent to that of aluminum measures 14.6 wt % in EPON-815, 14.8 wt % in DER-330, 14.9 wt % in DER-383, and 15.9 wt % in DEN-431. The radiopaque resins remain transparent indefinitely, even when exposed to water. © 1995 John Wiley & Sons, Inc.     

Interpretation of Third Phase Formation in the Th(IV)–HNO3, TBP–n‐Octane System with Baxter's “Sticky Spheres” Model

Abstract

Small‐angle neutron scattering (SANS) data for the tri‐n‐butylphosphate (TBP)–n‐octane, HNO₃–Th(NO₃)₄ solvent extraction system, obtained under a variety of experimental conditions, have been interpreted using two different models. The particle growth model led to unrealistic results. The Baxter model for hard‐spheres with surface adhesion, on the other hand, was more successful. According to this model, the increase in scattering intensity in the low Q range observed when increasing amounts of Th(NO₃)₄ are extracted into the organic phase, has been interpreted as arising from interactions between small reverse micelles containing three TBP molecules. Upon extraction of Th(NO₃)₄, the micelles interact through attractive forces between their polar cores with a potential energy of up to about 2 k_BT. The intermicellar attraction, under suitable conditions, leads to third phase formation. Upon phase splitting, most of the solutes of the original organic phase separate in a continuous phase containing interspersed layers of n‐octane.     

Formation and Growth of Micelles in Dilute Aqueous CTAB Solutions in the Presence of NaNO<Subscript>3</Subscript> and NaClO<Subscript>3</Subscript>

Self-assembly of cetyltrimethylammonium bromide (CTAB) in aqueous solution, in the presence of two inorganic salts viz, NaNO₃ and NaClO₃ was investigated by steady-state fluorescence, electrical conductance, surface tension, viscosity, dynamic light scattering (DLS) and cryogenic transmission microscopy (cryo-TEM). The counterions located at short enough distances to CTA⁺ micellar surface experience a very strong electrostatic attraction and thus become condensed. This counterion condensation plays a significant role in deciding the effective charge on the micelle, their screening interaction and structural transition of the micelles. In the present work, the probable mechanism of the salts' action in aqueous solution of CTAB is explained. The critical micelle concentration (CMC), area per molecule (Ų), micelle hydrodynamic diameter (D _h ), and aggregation number (N _agg) of CTAB micelles in the absence and presence of the salts are reported. The addition of both salts followed the lyotropic series and showed a remarkable decrease in CMC. A detailed investigation of the structural transitions from spherical to rod or even to entangled wormlike structures is presented from cryoTEM.     

Effects of Tween 80 concentration as a surfactant additive on morphology and permeability of flat sheet polyethersulfone (PES) membranes

In this study, effects of Tween 80 (polyoxyethylene sorbitan monooleate) as a variable hydrophilic surfactant additive on morphology and permeability of flat sheet polyethersulfone (PES) membranes prepared from PES/polyethylene glycol (PEG)/n-methyl-2-pyrrolidone (NMP) system via phase inversion induced by immersion precipitation in water coagulation bath were investigated. Cross-sectional morphology of the prepared membranes was studied by scanning electron microscopy (SEM). Permeation performance of the prepared membranes was evaluated in terms of pure water permeability (L_P), water content, porosity, hydraulic permeability and thickness of the prepared membranes. It was found out that little addition of Tween 80 to the casting solution increases water content and porosity of the membrane support layer and enhances pure water permeability through the membranes.     

Comparison of micelles formed by amphiphilic poly(ethylene glycol)‐b‐poly(trimethylene carbonate) star block copolymers

In this article, we describe the synthesis and solution properties of PEG‐b‐PTMC star block copolymers via ring‐opening polymerization (ROP) of trimethylene carbonate (TMC) monomer initiated at the hydroxyl end group of the core PEG using HCl Et₂O as a monomer activator. The ROP of TMC was performed to synthesize PEG‐b‐PTMC star block copolymers with one, two, four, and eight arms. The PEG‐b‐PTMC star block copolymers with same ratio of between hydrophobic PTMC and hydrophilic PEG segments were obtained in quantitative yield and exhibited monomodal GPC curves. The amphiphilic PEG‐b‐PTMC star block copolymers formed spherical micelles with a core–shell structure in an aqueous phase. The mean hydrodynamic diameters of the micelles increased from 17 to 194 nm with increasing arm number. As arm number increased, the critical micelle concentration (CMC) of the PEG‐b‐PTMC star block copolymers increased from 3.1 × 10^?3 to 21.1 × 10^?3 mg/mL but the partition equilibrium constant, which is an indicator of the hydrophobicity of the micelles of the PEG‐b‐PTMC star block copolymers in aqueous media, decreased from 4.44 × 10⁴ to 1.34 × 10⁴. In conclusion, we confirmed that the PEG‐b‐PTMC star block copolymers form micelles and, hence, may be potential hydrophobic drug delivery vehicles. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Neutron Polarization Analysis for Biphasic Solvent Extraction Systems

We performed neutron polarization analysis (NPA) of extracted organic phases containing complexes, comprised of Zr(NO₃)₄ and tri-n-butyl phosphate, which enabled decomposition of the intensity distribution of small-angle neutron scattering (SANS) into the coherent and incoherent scattering components. The coherent scattering intensity, containing structural information, and the incoherent scattering compete over a wide range of magnitude of scattering vector, q, specifically when q is larger than q* ≈ 1/R_g, where R_g is the radius of gyration of scatterer. Therefore, it is important to determine the incoherent scattering intensity exactly to perform an accurate structural analysis from SANS data when R_g is small, such as the aforementioned extracted coordination species. Although NPA is the best method for evaluating the incoherent scattering component for accurately determining the coherent scattering in SANS, this method is not used frequently in SANS data analysis because it is technically challenging. In this study, we successfully demonstrated that experimental determination of the incoherent scattering using NPA is suitable for sample systems containing a small scatterer with a weak coherent scattering intensity, such as extracted complexes in biphasic solvent extraction systems.     

Characterization of aqueous micellar solutions of amphiphilic block copolymers of poly(acrylic acid) and polystyrene prepared via ATRP. Toward the control of the number of particles in emulsion polymerization

A series of diblock, triblock and star-block copolymers composed of polystyrene and poly(acrylic acid) were synthesized by ATRP. The structure of the copolymers, the size of the blocks and the composition were varied, keeping however a short polystyrene block and a poly(acrylic acid) content larger than 60 mol% to allow solubility in alkaline water. Their micellization was studied by static and dynamic light scattering and the influence of their structural characteristics on the aggregation number, N_agg, was examined at low salt concentration and alkaline pH. It was shown that micelles were in thermodynamic equilibrium and that N_agg followed the power law N_agg∼N_A^−0.9N_S² (with N_A, the total number of acrylic acid units in the copolymer and N_S, the total number of styrene units), that is characteristic of amphiphile micelles formed from strongly segregated block copolymers. Moreover, N_agg was independent of salt concentration in the investigated range. The same copolymers were previously used as stabilizers in emulsion polymerization [Macromolecules 34 (2001) 4439]. The final latex particle concentration, N_p, was compared with N_m, the initial micelle concentration. This enabled us to conclude that among the block copolymers studied, those with high acid content behaved like low molar mass surfactants. In contrast, those with low acid content formed stable micelles that could be directly nucleated to create latex particles, allowing a good control over N_p.     

The effect of micellar lifetime on the rate of solubilization and detergency in sodium dodecyl sulfate solutions

The slow relaxation time (τ₂) of sodium dodecyl sulfate (SDS) micelles, measured by the pressure-jump technique, was maximum at 200 mM concentration at 25°C, indicating that the most stable micelles are formed at this concentration. This is presumably related to the optimum molecular packing in the micelle. The rate of solubilization of benzene and Orange OT dye into SDS solutions was also maximum at 200 mM concentration. The results are explained as follows: The distance between micelles (i.e., intermicellar distance) decreases as the surfactant concentration (or the number of micelles) increases, resulting in a stronger electric repulsion between micelles. Therefore, the micelles become more rigid, due to the compressive force of intermicellar repulsion, as the concentration increases up to 200 mM SDS. With further increase in the SDS concentration, the micellar shape changes from spherical to cylindrical to accommodate more surfactant molecules in the solution and to minimize the free energy of the system. The interior of the tightly packed micelles is more hydrophobic than that of loosely packed micelles and, therefore, the tightly packed micelles induce rapid solubilization of nonpolar molecules (e.g., benzene, Orange OT) into these micelles.     

Micellar solutions of amphipathic copolymers based on carboxymethyl cellulose

A novel family of amphipathic copolymers based on carboxymethyl cellulose (CM‐cellulose) has been synthesized through ultrasonic irradiation. Their micellar conformation in aqueous solution was studied by dynamic laser scattering, environmental scanning electron microscopy and gel permeation chromatography. The results show that conformation of copolymer molecules is totally different from that of CM‐cellulose because of the introduction of the surface active macromonomers. Due to the influence of hydrophobic character and molecular weight, different amphipathic copolymers have different micellar conformations, such as cylindrical, spheroidal or ellipsoidal micelles. In the range of concentration tested, the normalized first‐order autocorrelation function g⁽¹⁾(τ) of a copolymer of CM‐cellulose and poly(ethylene oxide) dodecyl ether acrylate does not fit a single‐exponential decay, indicating a polydisperse system and the existence of species of different shapes and size. At different concentrations, the hydrodynamic radii of micelles (R) almost distribute into two regions of smaller and larger size. With increasing copolymer concentration, the region of smaller R remains in the range 30–100 nm and is considered to represent monomolecular micelles, while the larger R region increases gradually with concentration, which means that polymolecular micelles increase in size. © 2003 Society of Chemical Industry     

Use of Foam Flotation to Remove tert-Butylphenol from Water

Abstract

The surfactants cetyl pyridinium chloride (CPC) and sodium dodecyl sulfate (SDS) were used in a study of an adsorptive bubble flotation process in batch mode to remove tert-butylphenol (TBP) from water. The TBP removal is maximized when the surfactant concentration is around the critical micelle concentration (CMC). Since micelles form above the CMC, this indicate that the higher the surfactant monomer concentration, the better the removal, but the micelles compete with the air/water interface for the TBP, resulting in micelles reducing removal efficiency. The addition of NaCl to the feed solution results in a significant reduction of the ability of CPC to remove TBP, while it improves the ability of SDS to remove TBP.