Phase imaging with intermodulation atomic force microscopy

Intermodulation atomic force microscopy (IMAFM) is a dynamic mode of atomic force microscopy (AFM) with two-tone excitation. The oscillating AFM cantilever in close proximity to a surface experiences the nonlinear tip-sample force which mixes the drive tones and generates new frequency components in the cantilever response known as intermodulation products (IMPs). We present a procedure for extracting the phase at each IMP and demonstrate phase images made by recording this phase while scanning. Amplitude and phase images at intermodulation frequencies exhibit enhanced topographic and material contrast.     

Time-lapse imaging of In Vitro myogenesis using atomic force microscopy

Myoblast therapy relies on the integration of skeletal muscle stem cells into distinct muscular compartments for the prevention of clinical conditions such as heart failure, or bladder dysfunction. Understanding the fundamentals of myogenesis is hence crucial for the success of these potential medical therapies. In this report, we followed the rearrangement of the surface membrane structure and the actin cytoskeletal organization in C2C12 myoblasts at different stages of myogenesis using atomic force microscopy (AFM) and confocal laser scanning microscopy (CLSM). AFM imaging of living myoblasts undergoing fusion unveiled that within minutes of making cell–cell contact, membrane tubules appear that unite the myoblasts and increase in girth as fusion proceeds. CLSM identified these membrane tubules as built on scaffolds of actin filaments that nucleate at points of contact between fusing myoblasts. In contrast, similarly behaving membrane tubules are absent during cytokinesis. The results from our study in combination with recent findings in literature further expand the understanding of the biochemical and membrane structural rearrangements involved in the two fundamental cellular processes of division and fusion.     

Identification and ultrastructural imaging of photodynamic therapy-induced microfilaments by atomic force microscopy

Atomic force microscopy (AFM) is an emerging technique for imaging biological samples at subnanometer resolution; however, the method is not widely used for cell imaging because it is limited to analysis of surface topology. In this study, we demonstrate identification and ultrastructural imaging of microfilaments using new approaches based on AFM. Photodynamic therapy (PDT) with a new chlorin-based photosensitizer DH-II-24 induced cell shrinkage, membrane blebbing, and reorganization of cytoskeletons in bladder cancer J82 cells. We investigated cytoskeletal changes using confocal microscopy and atomic force microscopy. Extracellular filaments formed by PDT were analyzed with a tandem imaging approach based on confocal microscopy and atomic force microscopy. Ultrathin filaments that were not visible by confocal microscopy were identified as microfilaments by on-stage labeling/imaging using atomic force microscopy. Furthermore, ultrastructural imaging revealed that these microfilaments had a stranded helical structure. Thus, these new approaches were useful for ultrastructural imaging of microfilaments at the molecular level, and, moreover, they may help to overcome the current limitations of fluorescence-based microscopy and atomic force microscopy in cell imaging.     

Immobilization method of yeast cells for intermittent contact mode imaging using the atomic force microscope

The atomic force microscope (AFM) is widely used for studying the surface morphology and growth of live cells. There are relatively fewer reports on the AFM imaging of yeast cells [1] (Kasas and Ikai, 1995), [2] (Gad and Ikai, 1995). Yeasts have thick and mechanically strong cell walls and are therefore difficult to attach to a solid substrate. In this report, a new immobilization technique for the height mode imaging of living yeast cells in solid media using AFM is presented. The proposed technique allows the cell surface to be almost completely exposed to the environment and studied using AFM. Apart from the new immobilization protocol, for the first time, height mode imaging of live yeast cell surface in intermittent contact mode is presented in this report. Stable and reproducible imaging over a 10-h time span is observed. A significant improvement in operational stability will facilitate the investigation of growth patterns and surface patterns of yeast cells.     

Capturing the elasticity and morphology of live fibroblast cell cultures during degradation with atomic force microscopy

Atomic force microscopy, in a liquid environment, was used to capture in vitro the morphological and mechanical changes that cultured fibroblasts undergo as time elapses from the completion of the cell culture. Topography images illustrated that initially, the nucleus had a height of 1.18 ± 0.2 μm, and after 48 h it had decreased to 550 ± 60 nm; similarly, the cell membrane exhibited significant shrinkage from 34 ± 4 to 23 ± 2 μm. After each image scan, atomic force microscopy indentation was performed on the centre of the nucleus, to measure the changes in the cell elasticity. Examination of the force‐distance curves indicated that the membrane elastic modulus at the nucleus remained the same within the time frame of 48 h, even though the cell morphology had significantly changed.     

Velocity dependent friction laws in contact mode atomic force microscopy

Friction forces in the tip–sample contact govern the dynamics of contact mode atomic force microscopy. In ambient conditions typical contact radii between tip and sample are in the order of a few nanometers. In order to account for the large interaction area the dynamics of contact mode atomic force microscope (AFM) is investigated under the assumption of a multi-asperity contact interface between tip and sample. Thus, the kinetic friction force between tip and sample is the product of the real contact area between both solids and the interfacial shear strength. The velocity strengthening of the lateral force is modeled assuming a logarithmic relationship between shear-strength and velocity. Numerical simulations of the system dynamics with this empirical model show the existence of two different regimes in contact mode AFM: steady sliding and stick–slip where the tip undergoes periodically stiction and kinetic friction. The state of the system depends on the scan velocity as well as on the velocity dependence of the interfacial friction force between tip and sample. Already small viscous damping contributions in the tip–sample contact are sufficient to suppress stick–slip oscillations.     

原子力显微镜原理与应用技术

本文简述原子力显微镜的工作原理,对比说明敲击模式的优越性,指出针尖-样品卷积效应和假象产生的原因,并例证其应用领域及其测试效果。     

Sample preparation procedures for biological atomic force microscopy

Since the late 1980s, atomic force microscopy (AFM) has been increasingly used in biological sciences and it is now established as a versatile tool to address the structure, properties and functions of biological specimens. AFM is unique in that it provides three-dimensional images of biological structures, including biomolecules, lipid films, 2D protein crystals and cells, under physiological conditions and with unprecedented resolution. A crucial prerequisite for successful, reliable biological AFM is that the samples need to be well attached to a solid substrate using appropriate, nondestructive methods. In this review, we discuss common techniques for immobilizing biological specimens for AFM studies.     

Fast contact-mode atomic force microscopy on biological specimen by model-based control

The dynamic behavior of the piezoelectric tube scanner limits the imaging rate in atomic force microscopy (AFM). In order to compensate for the lateral dynamics of the scanning piezo a model based open-loop controller is implemented into a commercial AFM system. Additionally, our new control strategy employing a model-based two-degrees-of-freedom controller improves the performance in the vertical direction, which is important for high-speed topographical imaging. The combination of both controllers in lateral and vertical direction compensates the three-dimensional dynamics of the AFM system and reduces artifacts that are induced by the systems dynamic behavior at high scan rates. We demonstrate this improvement by comparing the performance of the model-based controlled AFM to the uncompensated and standard PI-controlled system when imaging pUC 18 plasmid DNA in air as well as in a liquid environment.     

Adhesion artefacts in atomic force microscopy imaging

Artefacts that affect contrast and arise from adhesion forces in atomic force microscopy images of aramid fibres (both fresh and plasma-treated) are investigated. It is demonstrated that these stem not only from variations in the chemical composition of the surface but also from certain topographical features (which may appear hidden or enhanced in the images), resulting in changes in the lateral forces that are detected by the cantilever and are comparable to the vertical forces. It is also shown that both types of contribution to the forces can be uncoupled to yield images free from these artefacts, thus allowing more accurate quantitative measurements. These artefactual effects are also generally applicable to many other materials.     

A symmetrical stretching stage for electrical atomic force microscopy

We present a remotely-controlled device for sample stretching, designed for use with atomic force microscopy (AFM) and providing electrical connection to the sample. Such a device enables nanoscale investigation of electrical properties of thin gold films deposited on polydimethylsiloxane (PDMS) substrate as a function of the elongation of the structure. Stretching and releasing is remotely controlled with use of a dc actuator. Moreover, the sample is stretched symmetrically, which gives an opportunity to perform AFM scans in the same site without a time-consuming finding procedure. Electrical connections to the sample are also provided, enabling Kelvin probe force microscopy (KPFM) investigations. Additionally, we present results of AFM imaging using the stretching stage.     

Spectroscopy and atomic force microscopy of biomass

Scanning probe microscopy has emerged as a powerful approach to a broader understanding of the molecular architecture of cell walls, which may shed light on the challenge of efficient cellulosic ethanol production. We have obtained preliminary images of both Populus and switchgrass samples using atomic force microscopy (AFM). The results show distinctive features that are shared by switchgrass and Populus. These features may be attributable to the lignocellulosic cell wall composition, as the collected images exhibit the characteristic macromolecular globule structures attributable to the lignocellulosic systems. Using both AFM and a single case of mode synthesizing atomic force microscopy (MSAFM) to characterize Populus, we obtained images that clearly show the cell wall structure. The results are of importance in providing a better understanding of the characteristic features of both mature cells as well as developing plant cells. In addition, we present spectroscopic investigation of the same samples.     

Dynamic spring constants for higher flexural modes of cantilever plates with applications to atomic force microscopy

In atomic force microscopy (AFM) a sharp tip fixed close to the free end of a cantilever beam interacts with a surface. The interaction can be described by a point-mass model of an equivalent oscillator with a single spring located at the position of the tip. However, other spring constants have to be used to describe the oscillation behavior correctly if forces are acting on the cantilever over an extended lateral range. A point-mass model is then no longer valid. In the present study we derive expressions for the spring constants of cantilevers that can interact with any part of their plan view area along the beam and for all flexural modes. The equations describe the oscillation behavior in the corresponding mass model and are based on the eigenfrequencies and modal shapes of the free cantilever. The results are of high practical relevance, for example if an AFM is operated in a higher flexural mode, if the tip is not located at the free end of the cantilever beam, or if the external conservative forces affecting cantilever movement are not restricted to a single point. The limitations of the approach are discussed.     

Study of SU-8 photoresist cross-linking process by atomic force acoustic microscopy

In this paper, a method is presented to detect the different phases of epoxy cross-linking process and the subsurface structures of SU-8 thin films by atomic force acoustic microscopy (AFAM). The AFAM imaging of SU-8 thin films was investigated under different exposure and bake conditions. Optimized conditions were obtained for the cross-linking of SU-8 thin film at the exposure does of eight laser pulses with the laser fluence 10 mJ cm^–2 per pulse and the post exposure bake (PEB) time at 90 s. The subsurface structures of undeveloped SU-8 thin films were visible in the AFAM images. This method provides an effective and low-cost way for the determination of different phases of epoxy cross-linking process in nanostructured compounds, for the non-destructive testing of subsurface defects, and for the evaluation of the quality of patterned structures.     

An integrated approach to the study of living cells by atomic force microscopy

We describe a technique for studying living cells with the atomic force microscope (AFM) in tapping mode using a thermostated, controlled-environment culture system. We also describe the integration of the AFM with bright field, epifluorescence and surface interference microscopy, achieving the highest level of integration for the AFM thus far described. We succeeded in the continuous, long-term imaging of relatively flat but very fragile cytoplasmic regions of COS cells at a lateral resolution of about 70 nm and a vertical resolution of about 3 nm. In addition, we demonstrate the applicability of our technology for continuous force volume imaging of cultured vertebrate cells.
The hybrid instrument we describe can be used to collect simultaneously a diverse variety of physical, chemical and morphological data on living vertebrate cells. The integration of light microscopy with AFM and steady-state culture methods for vertebrate cells represents a new approach for studies in cell biology and physiology.     

日本精工SAP400原子力显微镜性能的改进

日本精工公司(SEIKO)生产的原子力显微镜的功能多、性能好,国内已经有近百台的拥有量。它的信号放大、处理主要由锁相放大器完成。但其内部的锁相放大器灵敏度不够高,外加一台高性能、高灵敏度的锁相放大器,可大大提高其性能。用美国斯坦福公司产的SR830锁相放大器对本实验室的日本SEIKO公司SPA400原子力显微镜进行性能改进,可使其性能有很大提高。     

Multifrequency high-speed phase-modulation atomic force microscopy in liquids

We have developed a new technique, called multifrequency high-speed phase-modulation atomic force microscopy (PM-AFM) in constant-amplitude (CA) mode based on the simultaneous excitation of the first two flexural modes of a cantilever. By performing a theoretical investigation, we have found that this technique enables the simultaneous imaging of the surface topography, energy dissipation and elasticity (nonlinear mapping) of materials. We experimentally demonstrated high-speed imaging at a scan speed of 5 frames/s for a polystyrene (PS) and polyisobutylene (PIB) polymer-blend thin-film surface in water.     

Climbing the steps of viral atomic force microscopy: visualization of Dengue virus particles

In recent years, the application of atomic force microscopy (AFM) to biological systems has highlighted the potential of this technology. AFM provides insights into studies of biological structures and interactions and can also identify and characterize a large panel of pathogens, including viruses. The Flaviviridae family contains a number of viruses that are important human and animal pathogens. Among them, Dengue virus causes epidemics with fatal outcomes mainly in the tropics. In this study, Dengue virus is visualized for the first time using the in air AFM technique. Images were obtained from a potassium-tartrate gradient-purified virus. This study enhances the application of AFM as a novel tool for the visualization and characterization of virus particles. Because flavivirus members are closely related, studies of the morphologic structure of the Dengue virus can reveal strategies that may be useful to identify and study other important viruses in the family, including the West Nile virus.     

Atomic force microscopy of silica nanoparticles and carbon nanohorns in macrophages and red blood cells

The emerging interest in understanding the interactions of nanomaterial with biological systems necessitates imaging tools that capture the spatial and temporal distributions and attributes of the resulting nano–bio amalgam. Studies targeting organ specific response and/or nanoparticle-specific system toxicity would be profoundly benefited from tools that would allow imaging and tracking of in-vivo or in-vitro processes and particle-fate studies. Recently we demonstrated that mode synthesizing atomic force microscopy (MSAFM) can provide subsurface nanoscale information on the mechanical properties of materials at the nanoscale. However, the underlying mechanism of this imaging methodology is currently subject to theoretical and experimental investigation. In this paper we present further analysis by investigating tip-sample excitation forces associated with nanomechanical image formation. Images and force curves acquired under various operational frequencies and amplitudes are presented. We examine samples of mouse cells, where buried distributions of single-walled carbon nanohorns and silica nanoparticles are visualized.     

Molecular dynamics of DNA and nucleosomes in solution studied by fast-scanning atomic force microscopy

Nucleosome is a fundamental structural unit of chromatin, and the exposure from or occlusion into chromatin of genomic DNA is closely related to the regulation of gene expression. In this study, we analyzed the molecular dynamics of poly-nucleosomal arrays in solution by fast-scanning atomic force microscopy (AFM) to obtain a visual glimpse of nucleosome dynamics on chromatin fiber at single molecule level. The influence of the high-speed scanning probe on nucleosome dynamics can be neglected since bending elastic energy of DNA molecule showed similar probability distributions at different scan rates. In the sequential images of poly-nucleosomal arrays, the sliding of the nucleosome core particle and the dissociation of histone particle were visualized. The sliding showed limited fluctuation within ∼50 nm along the DNA strand. The histone dissociation occurs by at least two distinct ways: a dissociation of histone octamer or sequential dissociations of tetramers. These observations help us to develop the molecular mechanisms of nucleosome dynamics and also demonstrate the ability of fast-scanning AFM for the analysis of dynamic protein–DNA interaction in sub-seconds time scale.