Heterostructure bipolar transistor employing carbon-doped base grown with trimethyl-Ga and arsine

The investigation of an AlGaAs/GaAs HBT in which a heavily carbon doped base is grown by chemical beam epitaxy using trimethyl-Ga is reported. A planar technique which reduces surface recombination has been employed for selectively contacting the base region. A base width of 1000 AA and a high doping level of 7*10/sup 19/ cm/sup -3/ is used. The sheet resistance of the base is less than 100 Omega / Square Operator . This transistor has a maximum current gain of 25 at a current density of 1.3*10/sup 3/ A/cm/sup 2/.<>     

Heavily doped base GaInP/GaAs heterojunction bipolar transistor grown by chemical beam epitaxy

The first demonstration of a GaInP/GaAs heterojunction bipolar transistor grown by chemical beam epitaxy is reported. A common-emitter current gain of 30 at a current density of 110 A/cm/sup 2/ is obtained for a beryllium base doping as high as 8*10/sup 19/ cm/sup -3/. The base sheet resistance of 140 Omega / Square Operator is among the lowest reported values.<>     

A high current gain 4H-SiC NPN power bipolar junction transistor

This work reports the development of high power 4H-SiC bipolar junction transistors (BJTs) by using reduced implantation dose for p+ base contact region and annealing in nitric oxide of base-to-emitter junction passivation oxide for 2 hours at 1150/spl deg/C. The transistor blocks larger than 480 V and conducts 2.1 A (J/sub c/=239 A/cm/sup 2/) at V/sub ce/=3.4 V, corresponding to a specific on-resistance (R/sub sp on/) of 14 m/spl Omega/cm/sup 2/, based on a drift layer design of 12 /spl mu/m doped to 6/spl times/10/sup 15/cm/sup -3/. Current gain /spl beta//spl ges/35 has been achieved for collector current densities ranging from J/sub c/=40 A/cm/sup 2/ to 239 A/cm/sup 2/ (I/sub c/=2.1 A) with a peak current gain of 38 at J/sub c/=114 A/cm/sup 2/.     

Double heterojunction bipolar transistor in Al/sub x/Ga/sub 1-x/As/GaAs/sub 1-y/Sb/sub y/ system

Double heterojunction bipolar transistors based on the Al/sub x/Ga/sub 1-x/As/GaAs/sub 1-y/Sb/sub y/ system are examined. The base layer consists of narrow band gap GaAs/sub 1-y/Sb/sub y/ and the emitter and collector consist of wider band gap Al/sub x/Ga/sub 1-x/As. Preliminary experimental results show that AlGaAs/GaAsSb/GaAs DHBTs exhibit a current gain of five and a maximum collector current density of 5*10/sup 4/ A/cm/sup 2/.<>     

Wideband DHBTs using a graded carbon-doped InGaAs base

We report an InP/InGaAs/InP double heterojunction bipolar transistor (DHBT), fabricated using a mesa structure, exhibiting 282 GHz f/sub /spl tau// and 400 GHz f/sub max/. The DHBT employs a 30 nm InGaAs base with carbon doping graded from 8/spl middot/10/sup 19//cm/sup 3/ to 5/spl middot/10/sup 19//cm/sup 3/, an InP collector, and an InGaAs/InAlAs base-collector superlattice grade, with a total 217 nm collector depletion layer thickness. The low base sheet (580 /spl Omega/) and contact (<10 /spl Omega/-/spl mu/m/sup 2/) resistivities are in part responsible for the high f/sub max/ observed.     

Demonstration of 1789 V, 6.68 m/spl Omega/ /spl middot/ cm/sup 2/ 4H-SiC merged-PiN-Schottky diodes

The design, fabrication and characterisation of a high performance 4H-SiC diode of 1789 V-6.6 A with a low differential specific-on resistance (R/sub SP/spl I.bar/ON/) of 6.68 m/spl Omega/ /spl middot/ cm/sup 2/, based on a 10.3 /spl mu/m 4H-SiC blocking layer doped to 6.6/spl times/10/sup 15/ cm/sup -3/, is reported. The corresponding figure-of-merit of V/sub B//sup 2//R/sub SP/spl I.bar/ON/ for this diode is 479 MW/cm/sup 2/, which substantially surpasses previous records for all other MPS diodes.     

4H-SiC power bipolar junction transistor with a very low specific ON-resistance of 2.9 m/spl Omega//spl middot/cm/sup 2/

This letter reports a newly achieved best result on the specific ON-resistance (R/sub SP/spl I.bar/ON/) of power 4H-SiC bipolar junction transistors (BJTs). A 4H-SiC BJT based on a 12-/spl mu/m drift layer shows a record-low specific-ON resistance of only 2.9 m/spl Omega//spl middot/cm/sup 2/, with an open-base collector-to-emitter blocking voltage (V/sub ceo/) of 757 V, and a current gain of 18.8. The active area of this 4H-SiC BJT is 0.61 mm/sup 2/, and it has a fully interdigitated design. This high-performance 4H-SiC BJT conducts up to 5.24 A at a forward voltage drop of V/sub CE/=2.5 V, corresponding to a low R/sub SP-ON/ of 2.9 m/spl Omega//spl middot/cm/sup 2/ up to J/sub c/=859 A/cm/sup 2/. This is the lowest specific ON-resistance ever reported for high-power 4H-SiC BJTs.     

Photoconductivity measurements in optical fibre preforms

The AC photoconductivity and the photodielectric shift in UV-illuminated germano-silicate preforms and optical fibres has been measured using a noncontact microwave resonator technique at 2.9 GHz. The highest photoconductivity measured was 1.5*10/sup -6/ ( Omega cm)/sup -1/ and the largest measured photodielectric shift corresponded to an increase of the refractive index of 1.6*10/sup -2/. A permanently induced increase of the refractive index, 6.1*10/sup -3/, was also observed. The dark DC conductivity was measured to be 10/sup -15/ ( Omega cm)/sup -1/.<>     

Turn-on voltage investigation of GaAs-based bipolar transistors with Ga/sub 1-x/In/sub x/As/sub 1-y/N/sub y/ base layers

The fundamental lower limit on the turn on voltage of GaAs-based bipolar transistors is first established, then reduced with the use of a novel low energy-gap base material, Ga/sub 1-x/In/sub x/As/sub 1-y/N/sub y/. InGaP/GaInAsN DHBTs (x/spl sim/3y/spl sim/0.01) with high p-type doping levels (/spl sim/3/spl times/10/sup 19/ cm/sup -3/) and dc current gain (/spl beta//sub max//spl sim/68 at 234 /spl Omega///spl square/) are demonstrated. A reduction in the turn-on voltage over a wide range of practical base sheet resistance values (100 to 400 /spl Omega///spl square/) is established relative to both GaAs BJTs and conventional InGaP/GaAs HBTs with optimized base-emitter interfaces-over 25 mV in heavily doped, high dc current gain samples. The potential to engineer turn-on voltages comparable to Si- or InP-based bipolar devices on a GaAs platform is enabled by the use of lattice matched Ga/sub 1-x/In/sub x/As/sub 1-y/N/sub y/ alloys, which can simultaneously reduce the energy-gap and balance the lattice constant of the base layer when x/spl sim/3y.     

Microwave performance of pseudomorphic resonant-tunnelling hot electron transistors at 77 K

Describes the first 77 K microwave measurements for resonant-tunnelling hot electron transistors (RHETs) fabricated using GaInAs/AlInAs pseudomorphic heterostructures. A collector current peak-to-valley ratio of 10 is obtained with a peak collector current density of 2*10/sup 5/ A/cm/sup 2/. A current gain cut-off frequency f/sub T/ of 63 GHz and a maximum oscillation frequency f/sub max/ of 44 GHz are measured at 77 K with an emitter current density of 1.1*10/sup 5/ A/cm/sup 2/.<>     

10-kV, 123-m/spl Omega//spl middot/cm/sup 2/ 4H-SiC power DMOSFETs

10-kV, 123-m/spl Omega//spl middot/cm/sup 2/ power DMOSFETs in 4H-SiC are demonstrated. A 42% reduction in R/sub on,sp/, compared to a previously reported value, was achieved by using an 8 /spl times/ 10/sup 14/ cm/sup -3/ doped, 85-/spl mu/m-thick drift epilayer. An effective channel mobility of 22 cm/sup 2//Vs was measured from a test MOSFET. A specific on-resistance of 123 m/spl Omega//spl middot/cm/sup 2/ were measured with a gate bias of 18 V, which corresponds to an E/sub ox/ of 3 MV/cm. A leakage current of 197 /spl mu/A was measured at a drain bias of 10 kV from a 4H-SiC DMOSFET with an active area of 4.24 /spl times/ 10/sup -3/ cm/sup 2/. A switching time of 100 ns was measured in 4.6-kV, 1.3-A switching measurements. This shows that the 4H-SiC power DMOSFETS are ideal for high-voltage, high-speed switching applications.     

High mobility NMOSFET structure with high-/spl kappa/ dielectric

High-/spl kappa/ NMOSFET structures designed for enhancement mode operation have been fabricated with mobilities exceeding 6000 cm/sup 2//Vs. The NMOSFET structures which have been grown by molecular beam epitaxy on 3-in semi-insulating GaAs substrate comprise a 10 nm strained InGaAs channel layer and a high-/spl kappa/ dielectric layer (/spl kappa//spl cong/20). Electron mobilities of >6000 and 3822 cm/sup 2//Vs have been measured for sheet carrier concentrations n/sub s/ of 2-3/spl times/10/sup 12/ and /spl cong/5.85/spl times/10/sup 12/ cm/sup -2/, respectively. Sheet resistivities as low as 280 /spl Omega//sq. have been obtained.     

A 4.15 kV 9.07-m/spl Omega//spl middot/cm/sup 2/ 4H-SiC Schottky-barrier diode using Mo contact annealed at high temperature

In this letter, we report the fabrication of high-voltage and low-loss 4H-SiC Schottky-barrier diodes (SBDs) with a performance close to the theoretical limit using a Mo contact annealed at high-temperature. High-temperature annealing for the Mo contact was found to be effective in controlling the Schottky-barrier height at 1.2-1.3 eV without degradation of n-factor and reverse characteristics. We successfully obtained a 1-mm/sup 2/ Mo-4H-SiC SBD with a breakdown voltage (V/sub b/) of 4.15 kV and a specific on resistance (R/sub on/) of 9.07 m/spl Omega//spl middot/cm/sup 2/, achieving a best V/sub b//sup 2//R/sub on/ value of 1898 MW/cm/sup 2/. We also obtained a 9-mm/sup 2/ Mo-4H-SiC SBD with V/sub b/ of 4.40 kV and R/sub on/ of 12.20 m/spl Omega//spl middot/cm/sup 2/.     

Extremely low-resistance nonalloyed ohmic contacts on molecular beam epitaxially grown p-type Ge

Extremely low-resistance nonalloyed ohmic contacts have been formed on p-type Ge grown on GaAs by molecular beam epitaxy as part of a research effort into GaAs/Ge heterojunction devices. Using evaporated Ti/Al metallisation, specific contact resistances well below 1*10/sup -8/ Omega cm/sup 2/ were achieved for heavily doped Ge (p>1*10/sup 19/ cm/sup -3/). The investigated Ge layers were grown as the base region of AlGaAs/Ge/GaAs HBTs. The influence of the low base resistance on the high-frequency performance of HBTs was studied by simulations.<>     

InGaAs/InP composite collector heterostructure bipolar transistors

A high speed bipolar transistor with high breakdown voltage BV/sub CEO/ is described. The structure uses a composite collector of InGaAs and InP. A common emitter gain of 65 is obtained with a base doping of 7*10/sup 19/ cm/sup -3/ and a breakdown voltage in excess of 10 V. The f/sub T/=64 GHz was reached at a collector-emitter voltage of 2 V and a current density of 52 kA/cm/sup 2/. The potential of this structure for very high speed applications is demonstrated by the extracted intrinsic transit time of 0.4 ps.<>     

Fabrication and characterization of 11-kV normally off 4H-SiC trenched-and-implanted vertical junction FET

This letter reports the first demonstration of 101 kV trenched-and-implanted normally off 4H-SiC vertical junction field-effect transistor (TI-VJFET) with a 120 /spl mu/m /spl sim/4.9/spl times/10/sup 14/ cm/sup -3/-doped drift layer. Blocking voltages (V/sub B/) of 10 kV to 11 kV have been measured. The best specific on-resistance (R/sub SP/_/sub ON/) normalized to source active area has been determined to be 130 m/spl Omega//spl middot/cm/sup 2/. Three-dimensional computer modeling including current spreading effect shows that the TI-VJFET would have a specific resistance of 168 m/spl Omega//spl middot/cm/sup 2/ if it is scaled up substantially in size.     

Reduction of 1/f noise in multiplexed linear In/sub 0.53/Ga/sub 0.47/As detector arrays via epitaxial doping

A significant (2-5*) reduction in 1/f noise was observed in In/sub 0.53/Ga/sub 0.47/As photodetector arrays read out by a PMOS multiplexer, when the epitaxial InP cap layer doping was changed from undoped to sulfur-doped n type of about 3*10/sup 16/ cm/sup -3/. A further decrease was observed when the InP buffer layer was also changed from undoped to sulfur-doped n type of about 5*10/sup 17/ cm/sup -3/. Data was presented for the variation of 1/f noise, within a temperature range of 18 degrees C to -40 degrees C. Surface states at the InP cap/SiN interface appears to be the primary source of 1/f noise, with the bulk states at the n/sup -/In/sub 0.53/Ga/sub 0.47/As buffer hetero-interface as a secondary source. Increased n-type doping in the high-bandgap InP cap and buffer layers may reduce electron trapping, and thus 1/f noise. The measured noise spectrum of InGaAs photodetectors varies as f/sup y/ with y being approximately -0.45 for device structures with doped and undoped InP can layers. For a doped InP buffer layer, this value of y is -0.3.<>     

GaInP/GaAs collector-up tunneling-collector heterojunction bipolar transistors (C-up TC-HBTs): optimization of fabrication process and epitaxial layer structure for high-efficiency high-power amplifiers

This paper describes a novel heterojunction bipolar transistor (HBT) structure, the collector-up tunneling-collector HBT (C-up TC-HBT), that minimizes the offset voltage V/sub CE,sat/ and the knee voltage V/sub k/. In this device, a thin GaInP layer is used as a tunnel barrier at the base-collector (BC) junction to suppress hole injection into the collector, which results in small V/sub CE,sat/. Collector-up configuration is used because of the observed asymmetry of the band discontinuity between GaInP and GaAs depending on growth direction. To minimize V/sub k/, we optimized the epitaxial layer structure as well as the conditions of ion implantation into the extrinsic emitter and post-implantation annealing. The best results were obtained when a 5-nm-thick 5/spl times/10/sup 17/-cm/sup -3/-doped GaInP tunnel barrier with a 20-nm-thick undoped GaAs spacer was used at the BC junction, and when 2/spl times/10/sup 12/-cm/sup -2/ 50-keV B implantation was employed followed by 10-min annealing at 390/spl deg/C. Fabricated 40/spl times/40-/spl mu/m/sup 2/ C-up TC-HBTs showed almost zero V/sub CE,sat/ (<10 mV) and a very small V/sub k/ of 0.29 V at a collector current density of 4 kA/cm/sub 2/, which are much lower than those of a typical GaInP/GaAs HBT. The results indicate that the C-up TC-HBT's are attractive candidates for high-efficiency high power amplifiers.     

Development of screen-printed silicon solar cells with high fill factors on 100 /spl Omega//sq emitters

High-quality DuPont screen-printed Ag contacts were achieved on high sheet-resistance emitters (100 /spl Omega//sq) by rapid alloying of PV168 Ag paste. Excellent specific contact resistance (/spl sim/1 m/spl Omega/-cm/sup 2/) in conjunction with high fill factor (FF) (0.775) were obtained on 100 /spl Omega//sq emitters by a 900/spl deg/C spike firing of the PV168 paste in a belt furnace. The combination of the alloying characteristics of the PV168 Ag paste and optimized single-step rapid low-thermal budget firing resulted in a cost-effective manufacturable process for high-efficiency Si solar cells. In addition, the co-fired 100 /spl Omega//sq cell showed a noticeable improvement of /spl sim/0.5% in absolute efficiency over a conventional co-fired 45 /spl Omega//sq emitter cell. Lighter doping in the 100 /spl Omega//sq emitter cell resulted in better blue-response compared to the conventional cell, contributing to /spl sim/1.3 mA/cm/sup 2/ improvement in short-circuit current. Improved surface passivation on 100 /spl Omega//sq emitter cell resulted in additional 0.6 mA/cm/sup 2/ increase in J/sub sc/, 15-mV higher V/sub oc/, and a 0.6% increase in absolute cell efficiency. Front grid design optimization resulted in a FF of 0.780, and a further improvement in cell efficiency to reach 17.4%.     

Nitride-based light-emitting diodes with Ni/ITO p-type ohmic contacts

The optical and electrical properties of Ni(5 nm)-Au(5 nm) and Ni(3.5 nm)-indium tin oxide (ITO) (60 nm) films were studied. It was found that the normalized transmittance of Ni/ITO film could reach 87% at 470 nm, which was much larger than that of the Ni-Au film. It was also found that the specific contact resistance was 5 /spl times/ 10/sup -4/ /spl Omega/ /spl middot/ cm/sup 2/ and 1 /spl times/ 10/sup -3/ /spl Omega/ /spl middot/ cm/sup 2/, respectively, for Ni-Au and Ni/ITO on p-GaN. Furthermore, it was found that the 20 mA output power of light-emitting diode (LED) with Ni-Au p-contact layer was 5.26 mW. In contrast, the output power could reach 6.59 mW for the LED with Ni/ITO p-contact layer.