Physical Properties of Polyethylene Modified with Crude Palm Oil

The influence of small amount of crude palm oil (CPO) content on the physical properties of high density polyethylene (HDPE) and linear low-density polyethylene (LLDPE) was investigated. The HDPE and LLDPE containing 2%, 3%, and 5% CPO were prepared in a twin-screw extruder. Then films of 0.2 mm thickness were produced by using blown film technique. The improvement in tensile strength and elongation at break with a concurrent decline in density implied the enhancement in toughness of the polymers by the addition of CPO. A gradual increase in impact strength of HDPE with the CPO content further supported the previous notation. The enhancement in the physical properties in the presence of CPO is believed to be attributed to the increased chain mobility of the polymer along with improved orientation strengthening in HDPE and LLDPE. Evidence from scanning electron micrographs was also used to support this contention. The decline in impact strength of LLDPE with the addition of CPO is associated with the formation of defects in the amorphous phase of LLDPE.     

Rheological and mechanical properties in polyethylene blends

Melt rheology and mechanical properties in linear low density polyethylene (LLDPE)/low density polyethylene (LDPE), LLDPE/high density polyethylene (HDPE), and HDPE/LDPE blends were investigated. All three blends were miscible in the melt, but the LLDPE/LDPE and HDPE/LDPE blends exibiled two crystallization and melting temperatures, indicating that those blends phase separated upon cooling from the melt. The melt strength of the blends increased with increasing molecular weight of the LDPE that was used. The mechanical properties of the LLDPE/LDPE blend were higher than claculated from a simple rule of mixtures, whiele those of the LLDPE/HDPE blend conformed to the rule of mixtures, but the properties of HDPE/LDPE were less than the rule of mixtures prediction.     

HDPE/LLDPE/POE薄膜性能的研究

采用线型低密度聚乙烯（LLDPE）和热塑性弹性体乙烯-辛烯共聚物（POE）对高密度聚乙烯（HDPE）薄膜进行改性,研究了LLDPE和POE对共混体系薄膜力学性能、加工性能的影响,探讨了LLDPE增强HDPE的机理。结果表明,加入一定量LLDPE,使HDPE／LLDPE薄膜的拉伸强度较纯HDPE薄膜有所增加,而单位冲击破损质量则有所下降。当w（LLDPE）为15％时,HDPE／LLDPE薄膜的拉伸强度提高21．6％,薄膜的单位冲击破损质量降低23．0％。在HDPE／LLDPE/POE三元体系中,当w（POE）,w（LLDPE）分别为10％,15％时,薄膜的拉伸强度、单位冲击破损质量、断裂伸长率比纯HDPE薄膜分别提高2．3％,113％。36．0％,综合性能良好。     

Studies on mechanical and thermal properties of ternary blends of polyethylenes. I

Six film samples of varying compositions of linear low‐density polyethylene (LLDPE), 10–35 wt %, and high‐density polyethylene (HDPE), 40–65 wt %, having a fixed percentage of low‐density polyethylene (LDPE) at 25 wt % were extruded by melt blending in a single‐screw extruder (L/D ratio = 20 : 1) of uniform thickness of 2 mil. The tensile strength, elongation at break, and impact strength were found to increase up to 60 wt % HDPE addition, starting from 40 wt % HDPE, in the blends and then decreased. The blend sample B‐500 was found to be more thermally stable than its counterparts. The appearance of a single peak beyond 45 wt % HDPE content in the blend in dynamic DSC scans showed the formation of miscible blend systems and this was further confirmed by scanning electron microscopic analysis. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 1691–1698, 2005     

Formation and characterization of polyethylene blends for autoclave‐based expanded‐bead foams

Blends of linear‐low‐density polyethylene (LLDPE), low‐density polyethylene (LDPE), and high‐ density polyethylene (HDPE) were foamed and characterized in this research. The goal was to generate clear dual peaks from the expanded polyethylene (EPE) foam beads made from these blends in autoclave processing. Three blends were prepared in a twin‐screw mixing extruder at two rotational speeds of 5 and 50 rpm: Blend1 (LLDPE with 20 wt% HDPE), Blend 2 (LLDPE with 20 wt% LDPE), and Blend 3 (LLDPE with 10 wt% HDPE and 10 wt% LDPE). The differential scanning calorimetric (DSC) measurement was taken at two cooling rates: 5 and 50°C/min. Although no dual peaks were present, the results showed that blending with HDPE has a more noticeable effect on the DSC curve of LLDPE than blending with LDPE. Also, the rotational speed and cooling rate affected the shape of the DSC curves and the percentage area below the onset point. The DSC characterization of the batch foamed blends revealed multiple peaks at certain temperatures, which may be mainly due to the annealing effect during the gas saturation process. POLYM. ENG. SCI., 2010. © 2009 Society of Plastics Engineers     

茂金属中密度聚乙烯的性能及加工应用

对茂金属中密度聚乙烯(MDPE)的结构与性能进行表征,并对其挤出和吹膜加工应用进行分析.结果表明,小试聚合得到的MDPE具有较窄的相对分子质量分布、较低的支化度,且拉伸屈服强度、弯曲强度显著高于线性低密度聚乙烯(LLDPE),冲击强度特别是低温冲击强度高于高密度聚乙烯(HDPE);MDPE属于假塑性流体,在低温时容易出现不稳定流动现象,在高剪切速率下可以观察到粘度和压力的异常反转现象;可在现有加工LLDPE的设备上顺利进行挤出、吹膜加工,且得到的薄膜在纵横向具有均匀性屈服强度、撕裂强度方面优于进口高性能LLDPE产品.     

Linear low-density polyethylene/high-density polyethylene blends: Effect of high-density polyethylene content on die swell and flow instability

This work aimed to evaluate the effect of high-density polyethylene (HDPE) content and of shear rate on the die swell and flow instability of linear low-density polyethylene (LLDPE)/HDPE blends. The results showed that the die swell of the LLDPE/HDPE blends increased with the increase in the shear rate. At high shear rates, the increase in the HDPE content led to an increase in the die swell of LLDPE/HDPE blends. The surface morphology analysis of the extrudates by optical and scanning electron microscopy revealed the presence of sharkskin and stick–slip flow instabilities in LLDPE and LLDPE/HDPE blends at the shear rates investigated. These instabilities were attenuated with the addition of HDPE and almost disappeared in the LLDPE/HDPE blend containing 50 wt% of HDPE.     

Mechanical properties of high‐density polyethylene/scrap rubber powder composites modified with ethylene–propylene–diene terpolymer,dicumyl peroxide,and silicone oil

The effect of ethylene–propylene–diene terpolymer (EPDM), dicumyl peroxide (DCP), and dimethyl silicone oil on the mechanical properties of high‐density polyethylene (HDPE) composites filled with 60 mesh cryogenically scrap rubber powder (SRP) was studied. The addition of 10 wt % EPDM, 0.2 wt % DCP, and 4 wt % dimethyl silicone oil significantly increased both the impact strength and elongation at break of the HDPE/SRP composites. After the modification, the impact strength increased by 160%, and the elongation at break increased by 150% for the composites containing 40 wt % SRP. The impact load–time curves showed that the increase of impact energy for the modified composites was attributed to the increase of the maximum force at yield point and the ductile deformation after yielding. The rheological behavior, dynamic mechanical properties, and morphology observation suggested that an enhanced adhesion between SRP and polymer matrix formed in the modified HDPE/SRP composites. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2020–2027, 2003     

Structural,thermal, and gas transport properties of HDPE/LLDPE blend‐based nanocomposites using a mixture of HDPE‐g‐MA and LLDPE‐g‐MA as compatibilizer

Nanocomposites based on high density polyethylene (HDPE)/linear low density polyethylene (LLDPE) blend were prepared by melt compounding in a twin‐screw extruder using organoclay (montmorillonite) as nano‐filler and a 50/50 wt% mixture of maleic anhydride functionalized high density polyethylene (HDPE‐g‐MA) and linear low density polyethylene (LLDPE‐g‐MA) as the compatibilizing system. The addition of a maleated polyethylene‐based compatibilizing system was required to improve the organoclay dispersion in the HDPE/LLDPE blend‐based nanocomposite. In this work, the relationships between thermal properties, gas transport properties, and morphology were correlated. The compatibilized nanocomposite exhibited an intercalated morphology with a small number of individual platelets dispersed in the HDPE/LLDPE matrix, leading to an significant decrease in the oxygen permeation coefficient of the nanocomposites. A decrease in the carbon dioxide permeability and oxygen permeability with increase of nanoclay was observed for the compatibilized nanocomposites. The carbon dioxide permeability of the compatibilized nanocomposites was lower than the carbon dioxide permeability of the uncompatibilized nanocomposites even with the low intrinsic barrier properties of the compatibilizer. These effects were attributed to a good dispersion of the inorganic filler, good wettability of the filler by the polymer matrix, and strong interactions at the interface that increased the tortuous path for diffusion. Theoretical permeability models were used to estimate the final aspect ratio of nanoclay in the nanocomposite and showed good agreement with the aspect ratio obtained directly from TEM images. POLYM. ENG. SCI., 56:765–775, 2016. © 2016 Society of Plastics Engineers     

Thermal characteristics and temperature profile changes of structurally different polyethylenes with peroxide modifications

Crosslinking and processing characteristics of polyethylenes (PEs) with different molecular architectures, namely high‐density polyethylene (HDPE), linear low‐density polyethylene (LLDPE), and low‐density polyethylene (LDPE), were studied with regard to the effects of peroxide modifications and coolant flow rates. Dicumyl peroxide (DCP) and di‐tert‐butyl peroxide (DTBP) were used as free‐radical inducers for crosslinking the PEs. The characteristics of interest included normalized gel content, real‐time temperature profiles and their cooling rates, exothermic period, crystallinity level, crystallization temperature, and heat distortion temperature. The experiments showed that LDPE exhibited the highest normalized gel content. The real‐time cooling rates, taken from the temperature profiles for all PEs before the crystallization region, were greater than those after the crystallization region. The cooling rate of the PEs increased with the presence of DCP, whereas the crystallization temperature of the PEs was lowered. The HDPE appeared to show the longest exothermic period as compared with those of the LLDPE and LDPE. The exothermic period showed an increase with increasing coolant flow rate, but it was decreased by the use of DCP. As for the effect of peroxide type, the gel content and cooling rate of the PE crosslinked by DCP were higher than those for the PE crosslinked by DTBP. The DTBP was the more effective peroxide for introducing crosslinks and simultaneously maintaining the crystallization behavior of the PE. J. VINYL ADDIT. TECHNOL., 20:80‐90, 2014. © 2014 Society of Plastics Engineers     

硅烷接枝交联HDPE、LLDPE及其共混物的结构研究

利用红外光谱、差示扫描量热法等方法研究了高密度聚乙烯(HDPE)、线性低密度聚乙烯(LLDPE)及其共混物的乙烯基三乙氧基硅烷(VTEOS)接枝及交联产物的分子结构、熔融行为。结果表明,VTEOS接枝交联PE能力为:LLDPE>HDPE/LLDPE共混物>HDPE;接枝和交联使HDPE、LLDPE及其共混物的结晶度和熔点降低,晶粒变得不均匀。     

Effects of different compatibilizers on the rheological,thermomechanical, and morphological properties of HDPE/LLDPE blend‐based nanocomposites

The influence of two different compatibilizers and their combination (maleic anhydride grafted high density polyethylene, HDPE‐g‐MA; maleic anhydride grafted linear low density polyethylene, LLDPE‐g‐MA; and 50/50 wt % mixture of these compatibilizers) on the rheological, thermomechanical, and morphological properties of HDPE/LLDPE/organoclay blend‐based nanocomposites was evaluated. Nanocomposites were obtained by melt‐intercalation in a torque rheometer in two steps. Masterbatches (compatibilizer/nanoclay 2:1) were obtained and subsequently diluted in the HDPE/LLDPE matrix producing nanocomposites with 2.5 wt % of nanoclay. Wide angle X‐ray diffraction (WAXD), steady‐state rheological properties, and transmission electron microscopy (TEM) were used to determine the influence of different compatibilizer systems on intercalation and/or exfoliation process which occurs preferentially in the amorphous phase, and thermomechanical properties. The LLDPE‐g‐MA with a high melt index (and consequently low viscosity and crystallinity) was an effective compatibilizer for this system. Furthermore, the compatibilized nanocomposites with LLDPE‐g‐MA or mixture of HDPE‐g‐MA and LLDPE‐g‐MA exhibited better nanoclay's dispersion and distribution with stronger interactions between the matrix and the nanoclay. These results indicated that the addition of maleic anhydride grafted polyethylene facilitates both, the exfoliation and/or intercalation of the clays and its adhesion to HDPE/LLDPE blend. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 1726–1735, 2013     

Influence of cocrystallization behavior on structure and properties of HDPE/LLDPE microporous membrane

The microporous membranes of high-density polyethylene (HDPE) and linear- lower-density polyethylene (LLDPE) blend were prepared based on melt-stretching mechanism and the influence of cocrystallization behavior on the structure and properties of stretched microporous membranes was investigated using scanning electron microscopy (SEM), differential scanning calorimetry (DSC), small-angle X-ray scattering (SAXS) and capillary flow porometer. It was found that compared with that without LLDPE, the main melting peak and the maximum crystallization temperature of HDPE/LLDPE blend precursor film with LLDPE content up to 12 wt.% were moved to lower temperature. The crystallinity of HDPE/LLDPE blend with LLDPE content of 5 wt.% was increased from 65.8 to 73.0 % due to the existence of cocrystallization behavior. The porosity and air permeability property of corresponding stretched microporous membrane were decreased by 7.1 and 44.4 %, respectively, whereas the puncture resistance was increased by 111.4 %. But further increase of LLDPE content to 12 wt.% lead to the decrease of cocrystallization ability and puncture resistance. To obtain final microporous membrane with better puncture resistance, adding 5 wt.% LLDPE to HDPE is appropriate. At the same time, although the air permeability is decreased, the value is still acceptable for the application of this kind of microporous membrane in the field of Li-ion battery as a separator.     

Implications of melt compatibility/incompatibility on thermal and mechanical properties of metallocene and Ziegler–Natta linear low density polyethylene (LLDPE) blends with high density polyethylene (HDPE): influence of composition distribution and branch content of LLDPE

In this paper, the implications of melt compatibility on thermal and solid‐state properties of linear low density polyethylene/high density polyethylene (LLDPE/HDPE) blends were assessed with respect to the effect of composition distribution (CD) and branch content (BC). The effect of CD was studied by melt blending a metallocene (m‐LLDPE) and a Ziegler‐Natta (ZN) LLDPE with the same HDPE at 190 °C. Similarly, the effect of BC was examined. In both cases, resins were paired to study one molecular variable at a time. Thermal and solid‐state properties were measured in a differential scanning calorimeter and in an Instron mechanical testing instrument, respectively. The low‐BC m‐LLDPE (BC = 14.5 CH₃/1000 C) blends with HDPE were compatible at all compositions: rheological, thermal and some mechanical properties followed additivity rules. For incompatible high‐BC (42.0 CH₃/1000 C) m‐LLDPE‐rich blends, elongation at break and work of rupture showed synergistic effects, while modulus was lower than predictions of linear additivity. The CD of LLDPE showed no significant effect on thermal properties, elongation at break or work of rupture; however, it resulted in low moduli for ZN‐LLDPE blends with HDPE. For miscible blends, no effect for BC or CD of LLDPE was observed. The BC of LLDPE has, in general, a stronger influence on melt and solid‐state properties of blends than the CD. Copyright © 2004 Society of Chemical Industry     

Blend of high‐density polyethylene and a linear low‐density polyethylene with compositional‐invariant mechanical properties

This article presents the tensile properties and morphological characteristics of binary blends of the high‐density polyethylene (HDPE) and a linear low‐density polyethylene (LLDPE). Two constituents were melt blended in a single‐screw extruder. Injection‐molded specimens were evaluated for their mechanical properties by employing a Universal tensile tester and the morphological characteristics evaluated by using a differential scanning calorimeter and X‐ray diffractometer. It is interesting to observe that the mechanical properties remained invariant in the 10–90% LLDPE content. More specifically, the yield and breaking stresses of these blends are around 80% of the corresponding values of HDPE. The yield elongation and elongation‐at‐break are around 65% to corresponding values of HDPE and the modulus is 50% away. Furthermore, the melting endotherms and the crystallization exotherms of these blends are singlet in nature. They cluster around the corresponding thermal traces of HDPE. This singlet characteristic in thermal traces entails cocrystallization between these two constituting components. The clustering of thermal traces of blends near HDPE meant HDPE‐type of crystallites were formed. Being nearly similar crystallites of blends to that of HDPE indicates nearness in mechanical properties are observed. The X‐ray diffraction data also corroborate these observations. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2604–2608, 2002     

Oriented structure and anisotropy properties of polymer blown films: HDPE, LLDPE and LDPE

Different types of polyethylene blown films (HDPE, LDPE, LLDPE) differ significantly in the ratio between machine and transverse direction tear resistance. In this paper, low density polyethylene (LDPE), linear low density polyethylene (LLDPE) and high density polyethylene (HDPE) blown films at different draw-down ratios are studied, and the relation between crystalline structure and anisotropy of blown film properties is investigated. The crystalline morphology and orientation of HDPE, LDPE, LLDPE blown films were probed using microscopy and infrared trichroism. Significant differences in crystalline morphology were found: at medium DDR HDPE developed a row-nucleated type morphology without lamellar twisting, LDPE showed rod-like crystalline morphology and turned out to the row-nucleated structure with twisted lamellae at high draw-down ratio (DDR), while a spherulite-like superstructure was observed for LLDPEs at all processing conditions. They also showed quite different orientation characteristics corresponding to different morphologies. The morphologies and orientation structure for LDPE, LLDPE and HDPE are related to the stress applied (DDR) and their relaxations in the flow-induced crystallization process, which determine the amount of fibrillar nuclei available at the time of crystallization and therefore, the final crystalline morphology. These structure differences are shown to translate into different ratios of machine and transverse direction tear and tensile strengths.     

硅烷交联EVA改性LLDPE材料

以过氧化二苯甲酰(BPO)为引发剂,乙烯基三甲氧基硅烷(A171)为交联剂和二月桂酸二丁基锡(DBTDL)为催化剂,采用两步法制备硅烷交联线型低密度聚乙烯(LLDPE),并添加适量的乙烯-醋酸乙烯共聚物(EVA)对产品进行改性。探究了温度、引发剂的用量、交联剂的用量对体系的接枝率、交联度、耐热性能和力学性能的影响。结果表明:在其他条件不变的情况下,在110~130℃范围内提高温度,可使凝胶率、维卡软化温度、拉伸强度先升高后降低,断裂伸长率降低;增加BPO的用量可以使凝胶率、维卡软化温度升高,断裂伸长率减小,拉伸强度先增大后减小;增加硅烷的用量可以使凝胶率、维卡软化温度、拉伸强度和断裂伸长率都升高。     

Ultrasonic velocity and attenuation of polymeric solids under oscillatory deformation. II: High density and linear low density polyethylene and their blends

In order to understand the viscoelastic non-linearities in polyethylene, dynamic ultrasonic properties of high density polyethylene (HDPE), linear low density polyethylene (LLDPE) and their blends were studied. In the case of HDPE and HDPE-rich films, for which the nonlinearity is high, the dynamic attenuation coefficient increased with the dynamic strain amplitude. The increase in the attenuation coefficient can be ascribed to plastic deformations such as defect- and/or void-formation in the spherulites. On the other hand, in LLDPE and LLDPE-rich blends for which the nonlinearity is low, the attenuation coefficient decreased with strain. The decrease in the attenuation coefficient can be ascribed to the orientation of lamellae. Thus, it was concluded that the viscoelastic nonlinearity of polyethylene is caused by plastic deformation. This conclusion was also deduced from other dynamic ultrasonic quantities such as the dynamic viscosity and dynamic density.     

Co‐crystallization in ternary polyethylene blends: tie crystal formation and mechanical properties improvement

Understanding the co‐crystallization behavior of ternary polyethylene (PE) blends is a challenging task. Herein, in addition to co‐crystallization behavior, the rheological and mechanical properties of melt compounded high density polyethylene (HDPE)/low density polyethylene (LDPE)/Zeigler ? Natta linear low density polyethylene (ZN‐LLDPE) blends have been studied in detail. The HDPE content of the blends was kept constant at 40 wt% and the LDPE/ZN‐LLDPE ratio was varied from 0.5 to 2. Rheological measurements confirmed the melt miscibility of the entire blends. Study of the crystalline structure of the blends using DSC, wide angle X‐ray scattering, small angle X‐ray scattering and field emission SEM techniques revealed the formation of two distinct co‐crystals in the blends. Fine LDPE/ZN‐LLDPE co‐crystals, named tie crystals, dispersed within the amorphous gallery between the coarse HDPE/ZN‐LLDPE co‐crystals were characterized for the first time in this study. It is shown that the tie crystals strengthen the amorphous gallery and play a major role in the mechanical performance of the blend.© 2016 Society of Chemical Industry     

小型中空吹塑料的研制

采用CaCO3和HDPE对LLDPE进行改性,研究了CaCO3和HDPE用量对共混体系力学性能的影响。结果表明,当m（LLDPE）∶m（HDPE）∶m（CaCO3）=55∶30∶15时,体系的综合力学性能最好。HDPE对LLDPE具有增强增韧作用,此外,添加少量的CaCO3能显著改善共混材料的力学性能,所制得的改性材料可用于生产小型中空制品。