Fibroblast Adhesion and Proliferation on a New β Type Ti-39Nb-13Ta-4.6Zr Alloy for Biomedical Application

Cell attachment and spreading on Ti-based alloy surfaces is a major parameter in implant technology. Ti-39Nb-13Ta-4.6Zr alloy is a new β type Ti alloy developed for biomedical application. This alloy has low modulus and high strength, which indicates that it can be used for medical purposes such as surgical implants. To evaluate the biocompatibility and effects of the surface morphology of Ti-39Nb-13Ta-4.6Zr on the cellular behaviour, the adhesion and proliferation of rat gingival fibroblasts were studied with substrates having different surface roughness and the results were also compared with commercial pure titanium and Ti-6Al-4V. The results indicate that fibroblast shows similar adhesion and proliferation on the smooth surfaces of commercial pure titanium （Cp Ti）, Ti-39Nb-13Ta-4.6Zr, and Ti-6Al-4V, suggesting that Ti-39Nb-13Ta-4.6Zr has similar biocompatibility to Cp Ti and Ti-6Al-4V. The fibroblast adhesion and spreading was lower on rough surfaces of Cp Ti, Ti-39Nb-13Ta-4.6Zr and Ti-6Al-4V than on smooth ones. Surface roughness appeared to be a dominant factor that determines the fibroblast adhesion and proliferation.     

Fibroblast Adhesion and Proliferation on a New β Type Ti-39Nb-13Ta-4.6Zr Alloy for Biomedical Application

Cell attachment and spreading on Ti-based alloy surfaces is a major parameter in implant technology. Ti39Nb-13Ta-4.6Zr alloy is a new β type Ti alloy developed for biomedical application. This alloy has low modulus and high strength, which indicates that it can be used for medical purposes such as surgical implants.To evaluate the biocompatibility and effects of the surface morphology of Ti-39Nb-13Ta-4.6Zr on the cellular behaviour, the adhesion and proliferation of rat gingival fibroblasts were studied with substrates having different surface roughness and the results were also compared with commercial pure titanium and Ti-6Al-4V. The results indicate that fibroblast shows similar adhesion and proliferation on the smooth surfaces of commercial pure titanium (Cp Ti), Ti-39Nb-13Ta-4.6Zr, and Ti-6Al-4V, suggesting that Ti-39Nb-13Ta-4.6Zr has similar biocompatibility to Cp Ti and Ti-6Al-4V. The fibroblast adhesion and spreading was lower on rough surfaces of Cp Ti, Ti-39Nb-13Ta-4.6Zr and Ti-6Al-4V than on smooth ones. Surface roughness appeared to be a dominant factor that determines the fibroblast adhesion and proliferation.     

增材制造Ti-6Al-4V合金组织调控研究现状

增材制造技术可实现复杂钛合金零件的快速成形,制造的Ti-6Al-4V合金具有较高的强度以及优异的高温性能,被广泛应用于航空、医疗等各大领域。综述了金属增材制造的典型工艺,分析了Ti-6Al-4V合金的相变特征,总结了选区激光熔化制造Ti-6Al-4V的力学性能和组织调控方法,着重分析了热处理温度、冷却速率、变质处理以及超声冲击等对合金组织的影响;展望了增材制造Ti-6Al-4V合金的主要发展方向。     

Corrosion behavior of PIRAC nitrided Ti-6Al-4V surgical alloy

Hard titanium nitride (TiN) coatings were obtained on the surface of Ti-6Al-4V alloy using an original PIRAC nitriding method, based on annealing the samples under a low pressure of monatomic nitrogen created by selective diffusion of N from the atmosphere. PIRAC nitrided samples exhibited excellent corrosion resistance in Ringer's solution in both potentiodynamic and potentiostatic tests. The anodic current and metal ion release rate of PIRAC nitrided Ti-6Al-4V at the typical corrosion potential values were significantly lower than those of the untreated alloy. This, together with the excellent adhesion and high wear resistance of the TiN coatings, makes PIRAC nitriding an attractive surface treatment for Ti-6Al-4V alloy surgical implants.     

Notch effects on high-cycle fatigue properties of Ti-6Al-4V ELI alloy at cryogenic temperatures

Notch effects on the high-cycle fatigue properties of the forged Ti-6Al-4V ELI alloy at cryogenic temperatures were investigated. Also, the high-cycle fatigue data were compared with the rolled Ti-5Al-2.5Sn ELI alloy. The one million cycles fatigue strength (FS) of the smooth specimen for the forged Ti-6Al-4V ELI alloy increased with a decrease of test temperature. However, the FS of each notched specimen at 4 K were lower than those at 77 K. On the other hand, the FS of the smooth and the notched specimens for the forged Ti-6Al-4V ELI alloy at 4 K were lower than those for the rolled Ti-5Al-2.5Sn ELI alloy. This is considered to be the early initiation of the fatigue crack in the forged Ti-6Al-4V ELI alloy compares with the forged Ti-5Al-2.5Sn ELI.     

TI-6Al-4V合金置氢-除氢组织与力学性能

为研究除氢处理对置氢钛合金组织与性能的影响,对Ti-6Al-4V合金在不同参数条件下进行了置氢与除氢处理,采用光学显微镜分析了置氢-除氢处理过程中Ti-6Al-4V合金微观组织的演化规律,通过室温拉伸试验研究了置氢-除氢处理后Ti-6Al-4V合金的力学性能,探讨了Ti-6Al-4V合金置氢-除氢组织与力学性能之间的相...     

Influences of processing parameters and heat treatment on microstructure and mechanical behavior of Ti-6Al-4V fabricated using selective laser melting

Selective laser melting (SLM) has provided an alternative to the conventional fabrication techniques for Ti-6Al-4V alloy parts because of its flexibility and ease in creating complex features. Therefore, this study investigated the effects of the process parameters and heat treatment on the microstructure and mechanical properties of Ti-6Al-4V fabricated using SLM. The influences of various process parameters on the relative density, tensile properties, impact toughness, and hardness of Ti-6Al-4V alloy parts were studied. By employing parameter optimization, a high-density high-strength Ti-6Al-4V alloy was fabricated by SLM. A relative density of 99.45%, a tensile strength of 1 188 MPa, and an elongation to failure of 9.5% were achieved for the SLM-fabricated Ti-6Al-4V alloy with optimized parameters. The effects of annealing and solution aging heat treatment on the mechanical properties, phase composition, and microstructure of the SLM-fabricated Ti-6Al-4V alloy were also studied. The ductility of the heat-treated Ti-6Al-4V alloy was improved. By applying a heat treatment at 850 ℃ for 2 h, followed by furnace cooling, the elongation to failure and impact toughness were found to be increased from 9.5% to 12.5%, and from 24.13 J/cm² to 47.51 J/cm², respectively.The full text can be downloaded at https://link.springer.com/article/10.1007/s40436-022-00389-y     

Use of a Laser/TIG Combination for Surface Modification of Ti-6Al-4V Alloy

The surface modification of materials such as Ti-6Al-4V is necessary to improve their wear resistant properties for use in tribological applications, in this paper it is shown that a laser with low power and tungsten inert gas (TIG) can be combined together for surface modification of Ti-6Al-4V alloy, and when performed in a controlled atmosphere of pure nitrogen or a mixture of nitrogen and argon, can produce a wear-resistant surface alloy. Compared with laser processing, a cheaper surface modification process has been developed involving a shorter processing time, which is free of stringent requirements such as a vacuum system.     

Superplastic deformation characteristics of two microduplex titanium alloys

A comparison of the superplastic deformation behaviour of Ti-6Al-4V (wt%) between 760 and 940‡ C and Ti-6Al-2Sn-4Zr-2Mo between 820 and 970‡ C has been carried out on sheet materials possessing similar as-received microstructures. High tensile elongations were obtained with maximum values being recorded at 880‡ C for Ti-6Al-4V (Ti-6/4) and at 940‡ C for Ti-6Al-2Sn-4Zr-2Mo (Ti-6/2/4/2), under which conditions both alloys possessed aΒ phase proportion of approximately 0.40. For a given deformation temperature the Ti-6/4 alloy had a slightly lower flow stress than the Ti-6/2/4/2, and this was attributed to the lowerΒ phase proportion in the latter alloy. However, at the respective optimum deformation temperatures the Ti-6/2/4/2 alloy had the lower flow stress. The results show that suitably processed Ti-6/2/4/2 alloy is capable of withstanding substantial superplastic strains at relatively low flow stresses, although the optimum deformation temperature is higher for this alloy than for Ti-6/4 material possessing a similar microstructure.     

Fabrication of spherical Ti-6Al-4V powder by RF plasma spheroidization combined with mechanical alloying and spray granulation

Spherical Ti-6Al-4V powder was produced by RF plasma spheroidization combined with mechanical alloying and spray granulation. Particle size distribution, morphology, specific surface area, apparent density, flowability, element distribution and content of alloy powders after each stage during the process were investigated. Results show that the obtained spheroidized Ti-6Al-4V alloy powder has dense structure, good sphericity and high spheroidization ratio (98%), moderate particle size (37.8 μm) with narrow distribution. It also has excellent flowability (33.2 s· (50 g)^-1) and apparent density (2.53 g·cm^?3). In addition, elements distribution in the spherical Ti-6Al-4V alloy powder is uniform and most of elements content of it is within the standard of Ti-6Al-4V alloy.     

氢对Ti-6Al-4V合金室温压缩性能的影响

为了研究氢对Ti-6Al-4V合金室温压缩性能的影响,采用Zwick/Z100型材料试验机对置氢Ti-6Al-4V合金进行了压缩试验,并利用OM、XRD和TEM等材料分析方法对合金的微观组织进行了观察.研究表明:置氢前,Ti-6Al-4V合金由等轴的α相和β相组成,置氢后,出现马氏体组织和氢化物;随氢含量增加,马氏体和剩余β相数量增多;氢提高了Ti-6Al-4V合金的抗压强度和塑性等室温压缩性能,最大增幅分别为33.9%和56.3%;置氢Ti-6Al-4V合金抗压强度的提高主要归因于氢的固溶强化、马氏体相变强化和氢化物强化;塑性指标的提高主要是置氢合金中塑性β相数量的增多所致.     

颗粒增强Ti基复合材料的特性

本文研究了采用粉末冶金工艺制备的碳化钛颗粒(TiCp)增强 Ti-Al-V 复合材料的显微组织、弹性模量、高温强度、蠕变行为及断裂特征。研究结果表明,选用合适的不连续增强相及 Ti合金基体可以获得增强相与基体结合良好、具有高比强、高比模、良好高温性能的不连续增强 Ti基复合材料。这些 Ti 基复合材料具有各向同性,可用于复杂应力状态,可通过热压、热挤压等一般热加工工艺加工成型。     

基于α'组织设计适于激光立体成形的新型高塑性Ti-4.13Al-9.36V合金

为了提高Ti-6Al-4V合金的加工硬化率和塑性,基于其团簇成分式12[Al-Ti₁₂](AlTi₂)+5[Al-Ti₁₄](V₂Ti)设计成分式为4[Al-Ti₁₂](AlTi₂)+12[Al-Ti₁₄](V₂Ti)的(Ti-4.13Al-9.36V, %)合金,采用激光立体成形工艺制备Ti-4.13Al-9.36V和Ti-6.05Al-3.94V(对比合金),研究了沉积态和固溶温度对其显微组织和力学性能的影响。结果表明,沉积态Ti-4.13Al-9.36V和Ti-6.05Al-3.94V合金的显微组织均由基体外延生长的初生β柱状晶和晶内细小的网篮α板条组成。Ti-6.05Al-3.94V合金的初生β柱状晶的宽度约为770 μm,α板条的宽度约为0.71 μm;而Ti-4.13Al-9.36V合金的初生β柱状晶的宽度显著减小到606 μm,α板条的宽度约为0.48 μm。经920℃固溶-淬火处理后Ti-6.05Al-3.94V样品的显微组织为α'+α相,其室温拉伸屈服强度约为893 MPa,抗拉强度约为1071 MPa,延伸率约为3%。经750℃固溶-淬火处理后Ti-4.13Al-9.36V样品的显微组织为α'+α相,与α'马氏体相比,应力诱发的α'马氏体能显著地提高合金的加工硬化能力,其室温拉伸屈服强度约为383 MPa,抗拉强度约为 989 MPa,延伸率达到了17%。这表明,根据团簇理论模型调控α'+α的显微组织能有效提高激光立体成形Ti合金的加工硬化能力和塑性。     

Ti-SiC Composite and TiC Ceramic Layer Formation on Ti6Al4V Surface by Laser Alloying of Pre-Placed SiC Coating

The Ti-6Al-4V alloy pre-placed with SiC coating was laser alloyed using high power CO2 laser. The laser alloyed cross section shows dendrite and Ti-SiC composite layer microstructure and the respective hardness was 650–800 HV and 1500–2000 HV. The observed hardness was 2 to 7 times greater than that measured on the bulk Ti-6Al-4V substrate. The laser alloyed surface produced high temperature ceramic phases such as TiC, TiSi and Ti5Si3. The elemental analysis was qualitatively estimated using SIMS analysis.     

神经网络预测搅拌摩擦加工TC4超塑性行为

目的 研究搅拌摩擦加工工艺改性的Ti–6Al–4V双相钛合金的超塑性变形行为。方法 对360 r/min、30mm/min工艺条件下搅拌摩擦加工处理的TC4钛合金在不同的变形条件下进行超塑性拉伸实验,在实验数据的基础上构建以变形温度、应变速率和晶粒尺寸为输入参数且以峰值应力为输出参数的3–16–1结构的BP人工神经网络模型。应用所构建的BP人工神经网络模型对不同变形条件的Ti–6Al–4V钛合金的超塑性行为进行预测。结果 BP人工神经网络预测的精准度较高,实验应力值与预测应力值吻合度较高,相关系数R=0.991 3,相对误差为1.91%～12.48%,平均相对误差为5.92%。结论 该模型预测的准确性较高,能够客观真实地描述Ti–6Al–4V合金的超塑性变形行为。     

Ti-6Al-4V合金表面超声振动滚压强化研究

采用超声振动滚压加工技术对Ti-6Al-4V合金表面进行处理,探究该项技术对Ti-6Al-4V合金表面质量的影响。通过对该工艺加工前后的Ti-6Al-4V合金进行表面粗糙度参数、XRD图谱、截面微观形貌、表层残余应力及显微硬度的对比分析,结果表明:经该工艺处理后的合金表面各项粗糙度参数皆有明显降低;加工后的合金表面XRD图谱的衍射峰减弱且宽化,衍射角向高角度方向偏移;加工后的合金表层β相组织相较加工前明显细化,且随着深度增加β相组织逐渐增大;在距离表面约50μm位置的残余应力值最大可达到-967 MPa;加工后的合金表面显微硬度可达到421HV,且在0~140μm的深度范围内,显微硬度随着深度的增加逐渐减小至与基体硬度一致。经超声振动滚压加工后的Ti-6Al-4V合金表面质量显著提高,有利于提高其零部件的使用性能。     

Preparation method of low-oxygen Ti-6Al-4V alloy by solid state re-deoxidation using calcium

The oxygen concentration in commercial Ti-6Al-4?V alloys was reduced to less than 400?ppm in this study by the method of solid state re-deoxidation, using calcium as a reductant. The concentration of oxygen in the deoxidised Ti-6Al-4?V alloy was 630?ppm at the optimum deoxidation temperature of 1000°C. When the degree of vacuum was increased and re-deoxidation was carried out, the oxygen concentration decreased to 355?ppm. Therefore, it is possible to prepare a Ti-6Al-4?V alloy with an oxygen concentration of less than 400?ppm by using the solid state re-deoxidation method at a high degree of vacuum of 1.5?×?10-6 Torr.     

Microstructure developed in the surface layer of Ti-6Al-4V alloy after sliding wear in vacuum

Microstructural changes in the surface layer of Ti-6Al-4V alloy after sliding wear in vacuum have been studied by means of scanning and transmission electron microscopy (SEM and TEM). The wear rates of Ti-6Al-4V alloy in vacuum were measured under different sliding velocities and loads. The experimental results showed that a severely deformed layer with a grain size of 50–100 nm and thickness about 70 μm was formed underneath the worn surface. Under the slower sliding velocities, the substructure of the layer had a high dislocation density, while under higher sliding velocities, twins were found to exist in the substructure. A process by which the deformed layer formed has been proposed and the deformation of materials at the contacting spots of the Ti-6Al-4V sample is discussed.     

A New Approach for Manufacturing a High Porosity Ti-6Al-4V Scaffolds for Biomedical Applications

Titanium and its alloys are currently considered as one of the most important metallic materials used in the biomedical applications, due to their excellent mechanical properties and superior biocompatibility. In the present study, a new effective method for fabricating high porosity titanium alloy scaffolds was developed. Porous Ti-6Al-4V scaffolds are successfully fabricated with porosities ranging from 30% to 70% using spaceholder and powder sintering technique. Based on its acceptable properties, spherical carbamide particles with different diameters （0.56, 0.8, and 1mm） were used as the space-holder material in the present investigation. The Ti-6Al-4V scaffolds porosity is characterized by using scanning electron microscopy. The results show that the scaffolds spherical-shaped pores are depending on the shape, size and distribution of the space-holder particles. This investigation shows that the present new manufacturing technique is promising to fabricate a controlled high porosity and high purity Ti-6Al-4V scaffolds for hard tissue replacement.     

Effect of the filament nature on fatigue crack growth in titanium based composites reinforced by boron,B(B4C) and SiC filaments

Crack propagation testing has been applied to synthetic metal matrix composites (MMC) in order to compare failure mechanisms in Ti-6Al-4V alloy reinforced by uncoated boron, B(B₄C) and chemical vapour deposition (CVD) SiC filaments. The impeding effect of the fibres leads to low crack growth rates, compared to those reported for the unreinforced Ti-6Al-4V alloy and to higher toughness despite the presence of the reinforcing brittle phases. After long isothermal exposures at 850° C, the MMC crack growth resistance is reduced mainly due to fibre degradation, fibre-matrix debonding and an increase in matrix brittleness. However, for short-time isothermal exposures (up to about 10 h for B/Ti-6Al-4V, 30 h for B (B₄C)/Ti-6Al-4V and 60 h for SiC/Ti-6Al-4V) the crack growth resistance is significantly increased. This improvement is related to the build up of an energy-dissipating mechanism by fibre microcracking in the vicinity of the crack tip. This damaging mechanism allowing matrix plastic deformation is already effective for boron and B(B₄C) in the as-fabricated state, but occurs only after 10 h of thermal exposure at 850° C in the case of SiC/Ti-6Al-4V composites.