The effects of triethylenetetramine grafting of multi‐walled carbon nanotubes on its dispersion,filler‐matrix interfacial interaction and the thermal properties of epoxy nanocomposites

This study describes the influence of triethylenetetramine (TETA) grafting of multi‐walled carbon nanotubes (MWCNTs) on the dispersion state, interfacial interaction, and thermal properties of epoxy nanocomposites. MWCNTs were first treated by a 3:1 (v/v) mixture of concentrated H₂SO₄/HNO₃, and then TETA grafting was performed. Chemically grafted MWCNT/bisphenol‐A glycidol ether epoxy resin/2‐ethyl‐4‐methylimidazole nanocomposites were prepared. TETA grafting could establish the connection of MWCNTs to the epoxy matrix and transform the smooth and nonreactive MWCNT surface into a hybrid material that possesses the characteristics of both MWCNTs and TETA, which facilitates homogeneous dispersion of MWCNTs and improves nanotube‐epoxy interfacial interaction. Therefore, the impact property, glass transition temperature, thermal stability, and thermal conductivity of epoxy nanocomposites are enhanced. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

A comparative study on the properties of the different amino‐functionalized multiwall carbon nanotubes reinforced epoxy resin composites

Multiwall carbon nanotubes (MWCNTs) were amino‐functionalized by 1,2‐ethylenediamine (EDA)' triethylenetetramine (TETA), and dodecylamine (DDA), and investigated by fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, and thermogravimetric analysis (TGA). The dispersion of the DDA functionalized MWCNT in DMF is better than that of the MWCNT functionalized by the EDA and the TETA. Carbon nanotubes reinforced epoxy resin composites were prepared, and the effect of the amino‐functionalization on the properties of the composites was investigated by differential scanning calorimetry (DSC), dynamical mechanical analysis (DMA), and TGA. The composites reinforced by the MWCNTs demonstrate improvement in various mechanical properties. The increase of T_g of the composites with the addition of amino‐functionalized MWCNT compared to the T_g of the composites with the addition of unfunctionalized MWCNT was due to the chemical combination and the physical entanglements between amino group from modified MWNTs and epoxy group from the epoxy resin. The interfacial bonding between the epoxy and the amino group of the EDA and the TETA‐modified MWCNT is more important than the well dispersion of DDA‐modified MWCNT in the composites for the improvement of the mechanical properties. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Cure behavior and thermal stability analysis of multiwalled carbon nanotube/epoxy resin nanocomposites

As‐received multiwalled carbon nanotubes (MWCNTs) were first treated by a 3 : 1 (v/v) mixture of concentrated H₂SO₄/HNO₃ and further functionalized by ethylenediamine/dicyclohexylcarbodiimide/tetrahydrofuran solution. MWCNT/epoxy nanocomposites were prepared. Their cure behaviors were investigated by dynamic differential scanning calorimetry. Quantitative analysis of the activation energy as a function of the degree of curing was carried out by the Flynn‐Wall‐Ozawa method. The fitted multiple regression equations for values of the activation energy of different systems were obtained. MWCNTs have the retardation effect on the cure reaction of epoxy resin, while the functional groups on the surface of amine‐modified MWCNTs could accelerate the cure reactions. Thermal stability was studied by thermogravimetric analysis. The filling of amine‐modified MWCNTs is beneficial to lower the cure activation energy and improve thermal stability of the nanocomposite. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of amino‐functionalization of multi‐walled carbon nanotubes on the dispersion with epoxy resin matrix

Amino‐functionalization of multiwalled carbon nanotubes (MWCNTs) was carried out by grafting triethylenetetramine (TETA) on the surfaces of MWCNTs through the acid–thionyl chloride way. The amino‐functionalized MWCNTs show improved compatibility with epoxy resin and, as a result, more homogenous dispersion in the matrix. The mechanical, optical, and thermal properties of the amino‐functionalized MWCNT/epoxy composites were also investigated. It was found that introducing the amino‐functionalized MWCNTs into epoxy resin greatly increased the charpy impact strength, glass transition temperature, and initial decomposing temperature of cured epoxy resin. In addition, introducing unfunctionalized MWCNTs into epoxy resin was found greatly depressing the light transmission properties, which would affirmatively confine the application of the MWCNTs/epoxy composites in the future, while much higher light transmittance than that of unfunctionalized MWCNTs/epoxy composites was found for amino‐functionalized MWCNTs/epoxy composites. SEM of the impact cross section and TEM of ultrathin film of the amino‐functionalized MWCNTs/epoxy composites showed that the amino‐functionalized MWCNTs were wetted well by epoxy matrix. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 97–104, 2006     

Self-assembled natural rubber/multi-walled carbon nanotube composites using latex compounding techniques

Functionalization of multi-walled carbon nanotubes (MWCNTs) plays an important role in eliminating nanotube aggregation for reinforcing polymeric materials. We prepared a new class of natural rubber (NR)/MWCNT composites by using latex compounding and self-assembly technique. The MWCNTs were functionalized with mixed acids (H2SO₄/HNO₃ = 3:1, volume ratio) and then assembled with poly (diallyldimethylammonium chloride) and latex particles. The Fourier transform infrared spectroscopy, transmission electron microscopy, and scanning electron microscopy were used to investigate the assembling mechanism between latex particles and MWCNTs. It is found that MWCNTs are homogenously dispersed in the natural rubber (NR) latex as individual nanotubes since strong self-aggregation of MWCNTs has been greatly depressed with their surface functionalization. The well-dispersed MWCNTs produce a remarkable increase in the tensile strength of NR even when the amount of MWCNTs is only 1 wt.%. Dynamic mechanical analysis shows that the glass transition temperature of composites is higher and the inner-thermogenesis and thermal stability of NR/MWCNT composites are better, when compared to those of the pure NR. The marked improvement in these properties is largely due to the strong interfacial adhesion between the NR phase and MWCNTs. Functionalization of MWCNTs represents a potentially powerful technology for significant reinforcement of natural rubber materials.     

Direct functionalization with 3,5‐substituted benzoic acids of multiwalled carbon nanotube/epoxy composites

Directly functionalized multiwalled carbon nanotubes (MWCNTs) with benzene‐1,3,5‐tricarboxylic acid (BTC) and 3,5‐diaminobenzoic acid (DAB) were successfully accomplished with less structural damage as confirmed by XPS and FT‐Raman results. Their dispersibility and thermal stability were achieved after the functionalization. The functional groups on MWCNT surfaces can accelerate the curing reaction of epoxy composites remarkable inducing rather low exothermic peak temperature (T_p) and exothermic heat of reaction (ΔH). The values of activation energy (E_a) obtained from Kissinger and Ozawa methods obviously decreased with the introduction of MWCNTs, especially DAB‐MWCNTs. The dynamic mechanical properties notably enhanced with the incorporation of unmodified and functionalized MWCNTs. The crosslink density (ρ) increased and free volume fraction (f_g) decreased, resulting in dramatic increase of glass transition temperatures (T_g) and decrease of coefficient of thermal expansion. Additionally, epoxy composites exhibited low dielectric constant close to that of neat epoxy resin. From these remarkable properties, MWCNT/epoxy composites can be considered as a good candidate for high performance insulation materials. POLYM. ENG. SCI., 53:2194–2204, 2013. © 2013 Society of Plastics Engineers     

Surface and structural characterization of multi-walled carbon nanotubes following different oxidative treatments

Six commonly used wet chemical oxidants (HNO₃, KMnO₄, H₂SO₄/HNO₃, (NH₄)₂S₂O₈, H₂O₂, and O₃) were evaluated in terms of their effects on the surface chemistry and structure of MWCNTs using a combination of analytical techniques. X-ray photoelectron spectroscopy (XPS) and energy dispersive spectroscopy (EDX) were used to characterize the extent of surface oxidation, while chemical derivatization techniques used in conjunction with XPS allowed the concentration of carboxyl, carbonyl, and hydroxyl groups at the surface to be quantified for each MWCNT sample. Our results indicate that the distribution of oxygen-containing functional groups was insensitive to the reaction conditions (e.g., w/w% of oxidant), but was sensitive to the identity of the oxidant. MWCNTs treated with (NH₄)₂S₂O₈, H₂O₂, and O₃ yielded higher concentrations of carbonyl and hydroxyl functional groups, while more aggressive oxidants (e.g., HNO₃, KMnO₄) formed higher fractional concentrations of carboxyl groups. IR spectroscopy was unable to identify oxygen-containing functional groups present on MWCNTs, while Raman spectra highlighted the frequently ambiguous nature of this technique for measuring CNT structural integrity. TEM was able to provide detailed structural information on oxidized MWCNT, including the extent of sidewall damage for different oxidative treatments.     

Quantitative characterization of acidic groups on acid-treated multi-walled carbon nanotubes using 1-aminopyrene as a fluorescent probe

Acidic functional groups produced on the surface of acid-treated multi-walled carbon nanotubes (MWCNTs) were quantified by fluorescence measurements using 1-aminopyrene (1-AP) as an in situ probe molecule. The 1-AP cation-like bands were observed on the HNO₃/H₂SO₄ mixture-treated MWCNT surfaces because the 1-AP molecule was tightly immobilized by the hydrogen bonding interaction between its amino group and the Brönsted-acidic groups on the MWCNT surface. The fluorescence measurement allowed us to confirm the Langmuir-type adsorption of 1-AP on the functional groups of the MWCNTs, and estimate their amount of the functional groups and adsorption equilibrium constant. A longer acid treatment caused the chemical modification to generate higher amounts of the Brönsted-acidic functional groups and improve the adsorption ability on the MWCNT surface. About 2% of carbon in the MWCNTs was oxidized by the 24 h acid treatment. This value corresponded to 15–22% of carbon in the surface layer.     

Fabrication of bimetallic nanoparticles/multi-walled carbon nanotubes composites for microelectronic circuits

A method for the fabrication of electrically-conducting polymer composites has been developed by mixing modified multi-walled carbon nanotubes (MWCNTs) functionalized by bimetallic nanoparticles (Ag/Ni/MWCNTs) into a UV curable resin. MWCNTs were treated by a concentrated H₂SO₄/HNO₃ mixture followed by ultrasonication with AgNO₃ and NiSO₄ in an ethylene glycol solution, producing MWCNTs decorated with Ag and Ni nanoparticles. The microstructure and surface morphology of the Ag/Ni/MWCNTs were investigated by scanning electron microscopy, transmission electron microscopy, and energy dispersive X-ray spectrometry. It was found that the addition sequences of NiSO₄ and AgNO₃ influence the morphology of the Ag/Ni/MWCNTs. The electrically-conducting polymer composites were obtained by dispersing the prefabricated Ag/Ni/MWCNTs in UV curable resin, the curing process of which was tracked by Fourier transform infrared spectroscopy, and the electrical resistance was measured using the four-probe method. The fabrication of microelectronic patterns made by screen printing on different substrates was described.     

A multi-step strategy for cutting and purification of single-walled carbon nanotubes

A multi-step procedure has been developed to cut and purify single-walled carbon nanotubes (SWCNTs) from the pristine soot synthesized by catalytic chemical vapor decomposition, which contains significant amount of multiwalled carbon nanotube (MWCNT) impurities. The procedure involves refluxing in dilute HNO₃ solution followed by (NH₄)₂S₂O₈/H₂SO₄ ultrasonication and a novel ammonia heat treatment step. The metal impurities are removed in the HNO₃ refluxing step. In the (NH₄)₂S₂O₈/H₂SO₄ treatment step, the SWCNTs are cut uniformly into micrometer long, while the MWCNTs are selectively cut into very short curled pieces. These short MWCNT pieces and the amorphous carbon impurities are partly removed in the (NH₄)₂S₂O₈/H₂SO₄ treatment step, and most of them are finally removed by the final ammonia heat treatment. The ammonia heat treatment step also recovers the structures of SWCNTs by healing defects on the sidewall. The final SWCNT products have purity higher than 95%, a length distribution between 1 and 2 μm, and very few defects.     

Thermal conductivity and dynamic mechanical property of glycidyl methacrylate‐grafted multiwalled carbon nanotube/epoxy composites

The well dispersed multiwalled carbon nanotube (MWCNT)/epoxy composites were prepared by functionalization of the MWCNT surfaces with glycidyl methacrylate (GMA). The morphology and thermal properties of the epoxy nanocomposites were investigated and compared with the surface characteristics of MWCNTs. GMA‐grafted MWCNTs improved the dispersion and interfacial adhesion in epoxy resin, and enhanced the network structure. The storage modulus of 3 phr GMA‐MWCNTs/epoxy composites at 50°C increased from 0.32 GPa to 2.87 GPa (enhanced by 799%) and the increased tanδ from 50.5°C to 61.7°C (increased by 11.2°C) comparing with neat epoxy resin, respectively. Furthermore, the thermal conductivity of 3 phr GMA‐MWCNTs/epoxy composite is increased by 183%, from 0.2042 W/mK (neat epoxy) to 0.5781 W/mK. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Mild functionalization of carbon nanotubes filled epoxy composites: Effect on electromagnetic interferences shielding effectiveness

The effect of nitric acid mild functionalized multiwalled carbon nanotubes (MWCNTs) on electromagnetic interference (EMI) shielding effectiveness (SE) of epoxy composites was examined. MWCNTs were oxidized by concentrated nitric acid under reflux conditions, with different reaction times. The dispersion of MWCNTs after functionalization was improved due to the presence of oxygen functional groups on the nanotubes surface. Functionalization at 2 h exhibits the highest EMI SE and electrical conductivity of MWCNTs filled epoxy composites. However, EMI shielding performance of MWCNTs filled epoxy composite declined when the functionalization reaction time was prolonged. This was due to extensive damage on the MWCNT structure, as verified by a Raman spectroscope. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42557.     

Properties and degradation behavior of surface functionalized MWCNT/poly(L‐lactide‐co‐ε‐caprolactone) biodegradable nanocomposites

In this research, poly(L ‐lactide‐co‐ε‐caprolactone) (PLACL) reinforced with well‐dispersed multiwalled carbon nanotubes (MWCNTs) nanocomposites were prepared by oxidization and functionalization of the MWCNT surfaces using oligomeric L ‐lactide (LA) and ε‐caprolactone (CL). It is found that the surface functionalization can effectively improve the dispersion and adhesion of MWCNTs in PLACL. The surface functionalization will have a significant effect on the physical, thermomechanical, and degradation properties of MWCNT/PLACL composites. The tensile modulus, yield stress, tensile strength, and elongation at break of composite increased 49%, 60%, 70%, and 94%, respectively, when the concentration of functionalized MWCNTs in composite is 2 wt %. The in vitro degradation rate of nanocomposites in phosphate buffer solution increased about 100%. The glass transition temperature (T_g) of composites was decreased when the concentration of functionalized MWCNTs is 0.5 wt %. With further increasing the concentration of functionalized MWCNTs, the T_g was increased. The degradation kinetics of nanocomposites can be engineered and functionalized by varying the contents of pristine or functionalized MWCNTs. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effect of carbon nanofiber functionalization on the in-plane mechanical properties of carbon/epoxy multiscale composites

In this work, vapor-grown carbon nanofibers (CNFs) were functionalized using an optimized route and dispersed in the matrix of carbon fabric-reinforced epoxy composites to develop multiscale carbon/epoxy composites. Functionalization was carried out through an oxidative treatment with a mixture of HNO₃/H₂SO₄ (1 : 3) using a combination of ultrasonication and magnetic stirring. Functionalized CNFs (F-CNFs) were characterized for their morphology, length, functional groups, and degradation due to oxidative treatment. The results showed that it was possible to efficiently functionalize CNFs without any degradation through proper selection of treatment duration. F-CNFs were dispersed homogeneously into the epoxy matrix using ultrasonication in combination with high-speed mechanical stirring. The incorporation of 0.1 wt % F-CNFs led to a 65% increase in Young's modulus and a 36% in tensile strength of neat carbon/epoxy composites. The fracture surfaces were studied using scanning electron microscopy to understand the property enhancement due to F-CNFs. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Rheological properties and fracture toughness of epoxy resin/multi‐walled carbon nanotube composites

Multi‐walled carbon nanotubes (MWCNTs), surface‐treated via chemical functionalization, i.e., oxidation and amidation, were used to reinforce diglycidylether of bisphenol F (DGEBF) epoxy resin. The effects of the functionalization on the dispersion stability, rheological properties, and fracture toughness of DGEBF/MWCNT composites were investigated. The dispersion homogeneity of the MWCNTs in the epoxy matrix improved after functionalization. In addition, isothermal rheology measurements revealed that the DGEBF/dodecyl amine‐functionalized MWCNT (D‐MWCNT) composite had a longer gel time and higher activation energy of cross‐linking than the DGEBF/acid‐treated MWCNT (A‐MWCNT) composite. The fracture toughness of the former was also significantly higher than that of the latter; this resulted from the relatively high dispersion stability of the D‐MWCNTs in the epoxy matrix, owing to the presence of alkyl groups on the D‐MWCNT surface. POLYM. ENG. SCI., 55:2676–2682, 2015. © 2015 Society of Plastics Engineers     

Functionalization of carbon nanotubes and carbon nanofibers used in epoxy/amine matrices that avoid partitioning of the monomers at the fiber interface

Single‐wall carbon nanotubes (SWCNT), multiwall carbon nanotubes (MWCNT), and carbon nanofibers (CNF) were oxidized with a conventional H₂SO₄/HNO₃ treatment, and the resulting COOH groups were esterified with phenyl glycidyl ether (PGE). Pristine, oxidized and esterified SWCNT, MWCNT, and CNF (1 wt%) were dispersed in diglycidyl ether of bisphenol A/polyether triamine, and cured to produce epoxy nanocomposite. The quality of the dispersion varied with surface modification in the order: COOH > unmodified > PGE, as assessed for SWCNT/epoxy composites using radial breathing modes in Raman spectra and scanning electron microscopy. Local bundling of PGE‐modified nanofillers was explained by a polymerization‐induced phase‐separation process. Dynamic mechanical analysis showed the presence of two relaxation peaks in nanocomposites prepared with unmodified and COOH‐modified SWCNT, MWCNT, and CNF, assigned to a partitioning of monomers at the carbon interface. This produced a significant decrease of the glass transition temperature. However, the esterification with PGE led to a single relaxation peak close to the one of the neat epoxy, for the three types of nanofillers without any penalty in the glassy and rubbery elastic moduli. The effect was explained by matrix exclusion from phase‐separated domains. POLYM. ENG. SCI., 2010. © 2009 Society of Plastics Engineers     

A study on rheological behavior of MWCNTs/epoxy composites

Rheological behaviors of multiwalled carbon nanotubes (MWCNTs)/epoxy composites with various MWCNT contents were investigated by using a time sweep and frequency sweep experiment with oscillatory rheometry. The functional groups on the acid-treated MWCNTs were investigated by fourier transfer-infrared spectroscopy (FT-IR). The composites containing acid-treated MWCNTs exhibited faster gel time than pure epoxy resins. The storage (G′) and loss (G″) moduli of the composites showed solid-like behavior owing to interaction between the MWCNTs and the epoxy resins. The 1.0 wt% MWCNT composites had the highest crosslinking activation energy (E_c) due to good dispersion and strong interfacial bonding. These results imply that three-dimensional crosslinking might take place among the hydroxyl group in epoxy resins and the carbonyl or hydroxyl group in acid-treated MWCNTs.     

Improving thermal conductivity and shear strength of carbon nanotubes/epoxy composites via thiol‐ene click reaction

This study investigates the effect of the thiol‐ene click reaction on thermal conductivity and shear strength of the epoxy composites reinforced by various silane‐functionalized hybrids of sulfhydryl‐grafted multi‐walled carbon nanotubes (SH‐MWCNTs) and vinyl‐grafted MWCNTs (CC‐MWCNTs). The results of Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, thermal gravimetric analysis (TGA), and transmission electron microscopy (TEM) show that the sulfhydryl groups and vinyl groups are successfully grafted onto the surface of MWCNTs, after treatment of MWCNT with triethoxyvinylsilane and 3‐mercaptopropyltrimethoxysilane, respectively. Scanning electron microscopy (SEM), HotDisk thermal constant analyzer (HotDisk), optical microscope, and differential scanning calorimetry (DSC) are used to characterize the resultant composites. It is demonstrated that the hybrid of 75 wt % SH‐MWCNTs and 25 wt % CC‐MWCNTs has better dispersion and stability in epoxy matrix, and shows a stronger synergistic effect in improving the thermal conductivity of epoxy composite via the thiol‐ene click reaction with 2,2′‐azobis(2‐methylpropionitrile) as thermal initiator. Furthermore, the tensile shear strength results of MWCNT/epoxy composites and the optical microscopy photographs of shear failure section indicate that the composite with the hybrid MWCNTs has higher shear strength than that with raw MWCNTs. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44579.     

Preparation and thermal,electrical, and morphological properties of multiwalled carbon nanotubeand epoxy composites

Multiwalled carbon nanotube (MWCNT)/epoxy composites are prepared, and the characteristics and morphological properties are studied. Scanning electron microscopy microphotographs show that MWCNTs are dispersed on the nanoscale in the epoxy resin. The glass‐transition temperature (T_g) of MWCNT/epoxy composites is dramatically increased with the addition of 0.5 wt % MWCNT. The T_g increases from 167°C for neat epoxy to 189°C for 0.5 wt % CNT/epoxy. The surface resistivity and bulk resistivity are decreased when MWCNT is added to the epoxy resins. The surface resistivity of CNT/epoxy composites decreases from 4.92 × 10¹² Ω for neat epoxy to 3.03 × 10⁹ Ω for 1 wt % MWCNT/epoxy. The bulk resistivity decreases from 8.21 × 10¹⁶ Ω cm for neat epoxy to 6.72 × 10⁸ Ω cm for 1 wt % MWCNT/epoxy. The dielectric constant increases from 3.5 for neat epoxy to 5.5 for 1 wt % MWCNT/epoxy. However, the coefficient of thermal expansion is not affected when the MWCNT content is less than 0.5 wt %. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1272–1278, 2007     

Enhancement in mechanical properties of multiwalled carbon nanotube‐reinforced epoxy composites: Crosslinking of the reinforcement with the matrix via diamines

In this study, the effect of diamine molecular structure, attached to the multiwalled carbon nanotubes (MWCNTs), on the interfacial interactions of the MWCNTs and the epoxy matrix was studied. Pristine MWCNTs were successfully functionalized with multiple aliphatic and aromatic diamines. It has been found that, compared to aliphatic molecules, aromatic diamines can yield higher functionalization degree, due to higher activity and longer half‐life of aromatic intermediates. However, at the same functionalization degree, the aliphatic ligands were more successful in reacting with epoxy chains and forming covalent bonds between the MWCNTs and the matrix. Considerable improvements were achieved in the mechanical properties of functionalized MWCNT‐reinforced epoxy composites in comparison with the pristine MWCNT‐reinforced composites. Fractography observations revealed distinct differences in the failure modes of reinforced composites after functionalization of the MWCNTs with diamines. POLYM. ENG. SCI., 59:1905–1910, 2019. © 2019 Society of Plastics Engineers