Bio‐based polymer nanocomposites based on layered silicates having a reactive and renewable intercalant

Soybean oil‐based polymer nanocomposites were synthesized from acrylated epoxidized soybean oil (AESO) combined with styrene monomer and montmorillonite (MMT) clay by using in situ free radical polymerization reaction. Special attention was paid to the modification of MMT clay, which was carried out by methacryl‐functionalized and quaternized derivative of methyl oleate intercalant. It was synthesized from olive oil triglyceride, as a renewable intercalant. The resultant nanocomposites were characterized by X‐ray diffraction (XRD) and transmission electron microscopy (TEM). The effect of increased nanofiller loading in thermal and mechanical properties of the nanocomposites was investigated by thermogravimetric analysis (TGA) and dynamic mechanical analysis (DMA). The nanocomposites exhibited improved thermal and dynamic mechanical properties compared with neat acrylated epoxidized soybean oil based polymer matrix. The desired exfoliated nanocomposite structure was achieved when the OrgMMT loading was 1 and 2 wt % whereas partially exfoliated nanocomposite was obtained in 3 wt % loading. It was found that about 400 and 500% increments in storage modulus at glass transition and rubbery regions, respectively were achieved at 2 wt % clay loading compared to neat polymer matrix while the lowest thermal degradation rate was gained by introducing 3 wt % clay loading. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 2031–2041, 2013     

Preparation and properties of montmorillonite‐based polyimide nanocomposites

Montmorillonite (MMT)‐based polyimide (PI) nanocomposites were prepared via two‐stage polymerization of PI using polyamic acid (PAA). The clay was organically modified using various alkylammonium ions to examine the effect of changes in alkyl length on the intercalation spacing of both the treated clays and their hybrids with PAA and PI. The intercalation behavior of clay in the PI matrix and its thermal and mechanical properties were investigated as a function of clay concentration. The d‐spacing of organically modified MMT (O‐MMT) increased with increasing length of the alkylammonium chain. PI/O‐MMT hybrids form exfoliated nanocomposites at clay concentrations below 2 wt%, while they form intercalated nanocomposites together with some exfoliated ones at clay contents exceeding 4 wt%. Young's modulus increased rapidly to a clay loading of 2 wt%, and leveled off with further increases in clay loading. The tensile strength at break increased rapidly up to a clay loading of 1 wt%, and then decreased sharply, while the strain at break showed a monotonic decrease with increasing clay loading from 0 to 8 wt%. The storage modulus, E′, in the temperature range below the glass transition temperature T_g, generally increased with increasing clay content, except at the highest clay content of 8 wt%. Copyright © 2004 Society of Chemical Industry     

Exfoliation targeted toughness enhancement in polypropylene‐blend‐ montmorillonite nanocomposites

BACKGROUND: Both exfoliated and toughened polypropylene‐blend‐montmorillonite (PP/MMT) nanocomposites were prepared by melt extrusion in a twin‐screw extruder. Special attention was paid to the enhancement of clay exfoliation and toughness properties of PP by the introduction of a rubber in the form of compatibilizer toughener: ethylene propylene diene‐based rubber grafted with maleic anhydride (EPDM‐g‐MA). RESULTS: The resultant nanocomposites were characterized using X‐ray diffraction, atomic force microscopy, scanning electron microscopy, thermogravimetric analysis, dynamic mechanical analysis and Izod impact testing methods. It was found that the desired exfoliated nanocomposite structure could be achieved for all compatibilizer to organoclay ratios as well as clay loadings. Moreover, a mechanism involving a decreased size of rubber domains surrounded with nanolayers as well as exfoliation of the nanolayers in the PP matrix was found to be responsible for a dramatic increase in impact resistance of the nanocomposites. CONCLUSION: Improved thermal and dynamic mechanical properties of the resultant nanocomposites promise to open the way for highly toughened super PPs via nanocomposite assemblies even with very low degrees of loading. Copyright © 2008 Society of Chemical Industry     

Property enhancement in unsaturated polyester nanocomposites by using a reactive intercalant for clay modification

Polymeric nanocomposites were synthesized from unsaturated polyester (UPE) matrix and montmorillonite (MMT) clay using an in situ free radical polymerization reaction. Organophilic MMT was obtained using a quaternary salt of coco amine as intercalant having a styryl group making it a reactive intercalant. The resultant nanocomposites were characterized via X‐ray diffraction and transmission electron microscopy. The effect of increased nanofiller loading on the thermal and mechanical properties of the nanocomposites was investigated. All the nanocomposites were found to have improved thermal and mechanical properties as compared with neat UPE matrix, resulting from the contribution of nanolayer connected intercalant‐to‐crosslinker which allows a crosslinking reaction. It was found that the partially exfoliated nanocomposite structure with an exfoliation dominant morphology was achieved when the MMT loading was 1 wt %. This nanocomposite exhibited the highest thermal stability, the best dynamic mechanical performance and the highest crosslinking density, most probably due to more homogeneous dispersion and optimum amount of styrene monomer molecules inside and outside the MMT layers at 1 wt % loading. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Effect of both silane‐grafted and ion‐exchanged organophilic clay in structural,thermal, and mechanical properties of unsaturated polyester nanocomposites

Unsaturated polyester (UPE) resin including styrene monomer was mixed with organophilic montmorillonite (MMT) clay and its crosslinking polymerization reaction was done in the presence of free‐radical initiator. MMT clay was modified with cetyl trimethly ammonium bromide and trimethoxy vinyl silane. The nanocomposites were characterized by X‐ray diffraction (XRD), atomic force microscopy (AFM), scanning electron microscopy (SEM), thermogravimetric and dynamic mechanical analyses (TGA and DMA). The exfoliated nanocomposite structure was obtained when the MMT clay was modified in the presence of both modifiers, whereas individual modifications all resulted in intercalated structures. The exfoliated UPE nanocomposite exhibited better thermal and dynamic mechanical properties when compared with pure UPE and other composites, even with 3 wt% clay loading. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

Synthesis of effective poly(4‐vinylpyridine) nanocomposites: in situ polymerization from edges/surfaces and interlayer galleries of clay

Poly(4‐vinylpyridine) (P4VP) nanocomposites have been prepared by using an in situ polymerization method in the presence of organically modified montmorillonite (MMT) clays with a quarternary salt of cocoamine containing a vinyl group, as well as trimethoxy vinyl silane. The nanocomposites were characterized by X‐ray diffraction (XRD), scanning electron microscopy (SEM), thermogravimetric analysis (TGA) and dynamic mechanical analysis (DMA). The desired exfoliated nanocomposite structure was achieved when the MMT modification was conducted in the presence of both modifiers, whereas individual modifications all resulted in intercalated structures. This resultant exfoliated nanocomposite was found to have better thermal stability and dynamic mechanical performance when compared to the other nanocomposites, even with 2 % clay loading. Copyright © 2005 Society of Chemical Industry     

Preparation of polystyrene–clay nanocomposites via dispersion polymerization using oligomeric styrene‐montmorillonite as stabilizer

This study describes the preparation of polystyrene–clay nanocomposite (PS‐nanocomposite) colloidal particles via free‐radical polymerization in dispersion. Montmorillonite clay (MMT) was pre‐modified using different concentrations of cationic styrene oligomeric (‘PS‐cationic’), and the subsequent modified PS‐MMT was used as stabilizer in the dispersion polymerization of styrene. The main objective of this study was to use the clay platelets as fillers to improve the thermal and mechanical properties of the final PS‐nanocomposites and as steric stabilizers in dispersion polymerization after modification with PS‐cationic. The correlation between the degree of clay modification and the morphology of the colloidal PS particles was investigated. The clay platelets were found to be encapsulated inside PS latex only when the clay surface was rendered highly hydrophobic, and stable polymer latex was obtained. The morphology of PS‐nanocomposite material (after film formation) was found to range from partially exfoliated to intercalated structure depending on the percentage of PS‐MMT loading. The impact of the modified clay loading on the monomer conversion, the polymer molecular weight, the thermal stability and the thermomechanical properties of the final PS‐nanocomposites was determined. Copyright © 2012 Society of Chemical Industry     

Structural effects of type of intercalant in poly (4‐vinylpyridine) nanocomposites: compatible homopolymer or block copolymer

4‐vinylpyridine monomer was mixed with organophilic montmorillonite (MMT) clay and polymerized in the presence of free‐radical initiator. MMT clay was rendered organophilic by means of ion‐exchanging sodium cations for low‐molecular‐weight quaternized poly(4‐vinylpyridine) (P4VP) homopolymer and diblock copolymers of styrene and quaternized 4‐vinylpyridine (SVP) with different sequence lengths. The swelling behaviour of the MMT clay was studied by X‐ray diffraction (XRD). After the cation exchange, the resulting organophilic clays showed an expansion of interlayer distance indicating the nanoscale ordering of intercalant polymer and MMT layers. The nanocomposite materials, when moulded, exhibited improved thermal stability and dynamic mechanical properties compared with neat P4VP. The composite, having longer ionic segments in its organophilic MMT, showed exfoliated nanocomposite structure as well as higher stiffness and damping properties at higher temperatures even for MMT loading as low as 2 wt%. Copyright © 2006 Society of Chemical Industry     

New aramid‐based nanocomposites: Synthesis and characterization

New type of nanocomposites containing various proportions of montmorillonite in aromatic polyamide was prepared via solution intercalation method. Aramid chains were synthesized by reacting 4,4′‐oxydianiline with isophthaloyl chloride in N,N′‐dimethyl acetamide. Dodecylamine was used as swelling agent to change the hydrophilic nature of montmorillonite into organophilic. Appropriate amounts of organoclay were mixed in the polymer solution using high‐speed mixer for complete dispersion of the clay. Thin films cast from these materials after evaporating the solvent were characterized by XRD, TEM, mechanical, thermal, and water absorption measurements. The structure and morphology of the nanocomposites determined by XRD and TEM revealed the formation of exfoliated and intercalated clay platelets in the aramid matrix. Mechanical data indicated improvement in the tensile strength and modulus of the nanocomposites with clay loading up to 6 wt%. The glass transition temperature increased up to 12 wt% clay content and thermal stability amplified with increasing clay loading. The water absorption reduced gradually as a function of organoclay and approached to zero with 20 wt% organoclay in the aramid. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Effect of oligomeric‐modified montmorillonite on morphology and properties of polycarbonate/montmorillonite nanocomposites

Low‐molecular‐weight copolymers of styrene and vinylbenzyl ammonium salts (oligomeric surfactant) were used to modify montmorillonite (MMT). The oligomeric‐modified MMT showed good thermal stability, which made it suitable to be used for preparing polycarbonate(PC)/MMT nanocomposites at high temperature. A different series of PC/MMT nanocomposites had been prepared by melt processing using a twin screw extruder. The effect of oligomeric surfactant structure and clay loading on the morphology, mechanical property, thermal stability, and color appearance of the nanocomposites were explored. The results of X‐ray diffraction and transmission electron microscopy analyses indicated that the PC/MMT nanocomposites had partially exfoliated structures. The PC/MMT nanocomposites were found to retain light colored, which was important for optical application. Compared to neat PC, the nanocomposites showed better properties of thermal stability and heat insulation. The mechanical properties of the nanocomposites are significantly enhanced by incorporating clay into the PC matrix. The tensile strength of nanocomposites with 2 wt% clay content was up to 55 MPa, which was much higher than that of the neat PC (37 MPa). The maximum tensile modulus value was 19% higher than that of neat PC. POLYM. COMPOS., 2013. © 2013 Society of Plastics Engineers     

A study of the effect of surfactants on the properties of polystyrene‐montmorillonite nanocomposites

Polystyrene‐Organo Montmorillonite (PS‐MMT) nanocomposites were prepared by suspension free radical polymerization of styrene in the dispersed organophilic montmorillonite. The results of X‐ray diffraction (XRD) and Transmission Electron Microscopy (TEM) indicated that exfoliated nanocomposites were achieved. The effect of organic modifiers (surfactants) on the properties of the synthesized nanocomposites was studied. It is found that polystyrene‐MMT nanocomposite with 5.0 wt% of organo‐MMT gave the greatest improvement in thermal stability, and polystyrene‐MMT nanocomposites with 7.5 wt% of organo‐MMT showed the greatest improvement in mechanical properties, compared with that of pure polystyrene (PS) in our experimental conditions. The alkyl chain length of surfactant used in fabricating organo‐MMT affects the synthesized PS nanocomposites: the longer the alkyl chain length that the surfactant possesses, the higher the glass transition temperature of the PS nanocomposite, However, the organoclay in the nanocomposites seems to play a dual role: (a) as nanofiller leading to the increase of storage modulus and (b) as plasticizer leading to the decrease of storage modulus. This results in a lower storage modulus of PS‐TMOMMT and PS‐TMTMMT nanocomposites than that of PS‐TMDMMT and PS‐TMCMMT nanocomposites. Further study is needed to confirm the above hypothesis.     

In situ development of bio‐based polyurethane‐blend‐epoxy hybrid materials and their nanocomposites with modified graphene oxide via non‐isocyanate route

We developed a series of sunflower oil‐based non‐isocyanate polyurethane (NIPU)‐blend‐epoxy hybrid materials (HNIPUs) and their nanocomposites with amine‐functionalized graphene oxide (AF‐GO). Firstly, carbonated sunflower oil (CSFO) containing five‐membered cyclocarbonate groups was synthesized by the reaction of epoxidized sunflower oil with carbon dioxide (CO₂) at a pressure of 50 bar and temperature of 110 °C. Then, a series of HNIPUs were synthesized using a mixture of CSFO and a commercially available epoxy resin in various amounts (10, 20 and 30 wt% with respect to CSFO) using isophorone diamine as the curing agent. The HNIPU with 30 wt% epoxy showed the best mechanical properties. Finally, nanocomposites of 30 wt% HNIPU‐based composition were prepared with various amounts of AF‐GO (0.3, 0.6 and 1.0 wt%) and were characterized using Fourier transform infrared and ¹H NMR spectroscopies, X‐ray diffraction and scanning electron microscopy. These results emphasize the potentiality of this environmentally friendly approach for preparing renewable HNIPU and nanocomposite materials of high performances. © 2018 Society of Chemical Industry     

Preparation and characterization of polystyrene–clay nanocomposites by free‐radical polymerization

The polymerizable cationic surfactant, vinylbenzyldimethylethanolammouium chloride (VBDEAC), was synthesized to functionalize montmorillonite (MMT) clay and used to prepare exfoliated polystyrene–clay nanocomposites. The organophilic MMT was prepared by Na⁺ exchanged montmorillonite and ammonium cations of the VBDEAC in an aqueous medium. Polystyrene–clay nanocomposites were prepared by free‐radical polymerization of the styrene containing intercalated organophilic MMT. Dispersion of the intercalated montmorillonite in the polystyrene matrix determined by X‐ray diffraction reveals that the basal spacing is higher than 17.6 nm. These nanocomposites were characterized by differential scanning calorimetry (DSC), transmission electron micrograph (TEM), thermal gravimetric analysis (TGA), and mechanical properties. The exfoliated nanocomposites have higher thermal stability and better mechanical properties than the pure polystyrene. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1370–1377, 2002     

Nanocomposite Formation in Hydrogenated Nitrile Rubber (HNBR)/Organo‐Montmorillonite as a Function of the Intercalant Type

Summary: Hydrogenated acrylonitrile butadiene rubber (HNBR) was melt compounded with montmorillonite (MMT) and organophilic modified MMTs prior to sulfur curing. In contrast to the micro‐composite formation resulting from the compounding of the HNBR and pristine MMT, the modified MMTs (i.e., octadecylamine: MMT‐ODA, octadecyltrimethylamine: MMT‐ODTMA, methyltallow‐bis(2‐hydroxyethyl) quaternary ammonium: MMT‐MTH intercalants) produced nanocomposites. It was found that the organoclay with primary amine intercalant (cf. MMT‐ODA) gave confined structures along with the exfoliated/intercalated structures. This was traced to its reactivity with the curatives. By contrast, the organoclays containing less reactive quaternary ammonium compounds (cf. MMT‐ODTMA, MMT‐MTH) were exfoliated and intercalated based on X‐ray diffraction (XRD) and transmission electron microscopy (TEM) results. The hydroxyl functional groups of the MMT‐MTH supported the clay dispersion. The better adhesion between MMT‐MTH and HNBR was explained by hydrogen bonding between the hydroxyl groups of the intercalant and the acrylonitrile group of the HNBR matrix. This HNBR/MMT‐MTH nanocomposite showed the best mechanical properties as verified by tensile mechanical tests and dynamic mechanical thermal analysis (DMTA). The high tensile strength along with the high elongation at break for the rubber nanocomposites were attributed to the ability of the ‘clay network’ to dissipate the input energy upon uniaxial loading.

Scheme of failure development in rubber/organoclay mixes with poor (a) and good (b) dispersion of the clay layers.     

Preparation and characterization of transparent poly(methyl methacrylate)/Na+‐MMT nanocomposite films by solution casting

Films of poly(methyl methacrylate) (PMMA)/sodium montmorillonite (Na⁺‐MMT) nanocomposites have been successfully prepared utilizing Na⁺‐MMT by N,N‐dimethylformamide solution casting. The nanocomposite films show high transparency, enhanced thermal resistance, and mechanical properties in comparison with the neat polymer film. The transparency of the films was investigated by UV‐vis spectra. The exfoliated dispersion of Na⁺‐MMT platelets in nanocomposites were investigated by X‐ray diffraction and transmission electron microscopy. The enhanced thermal resistance and mechanical properties of PMMA were studied by thermal gravimetric analysis and dynamic mechanical analysis, respectively. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Morphological influence on mechanical characterization of ethylene‐vinyl acetate copolymer–clay nanocomposites

Ethylene‐vinyl acetate copolymer (EVA)/montmorillonite (MMT) clay nanocomposites with varying degree of intercalation and exfoliation have been prepared using direct melt blending techniques with various degrees of polarity (9, 18, and 28 wt% vinyl acetate [VA]) and two different types of clay modification. Morphological characterization using wide‐angle X‐ray scattering (WAXS) and transmission electron microscopy (TEM) have indicated/confirmed the presence of intercalation and/or a combination of intercalation and exfoliation existing in the nanocomposites. The effects of these (simple intercalation or mixed intercalation/exfoliation) states and the effect of changing matrix polarity (by changing VA wt% content) on the nanocomposite mechanical behavior were studied. There is sufficient evidence from the mechanical studies that 1) the presence of nanoclay can simultaneously improve modulus and strength of the nanocomposites, and 2) the mechanical properties are a combined function of the clay concentration and the nanocomposite morphology (due to the VA wt% and presence of clay). It is shown here that interrelation between the VA wt% content and the clay exfoliation affects the mechanical properties in a way that has a positive and increasing slope with increasing loading of clay. It is shown that a clear understanding of the nanocomposite mechanical properties can be obtained from its morphological analysis. POLYM. ENG. SCI., 45:889–897, 2005. © 2005 Society of Plastics Engineers     

Synthesis and characterization of linseed oil‐based nanocomposites

The nanocomposites from conjugated linseed oil, acrylic acid, and divinylbenzene are synthesized using modified montmorillonite clay and characterized for thermal properties. The wide angle X‐ray diffraction results clearly show the distortion of the platy nanolayers of the nanofiller in the polymer matrix as the peak due to the clay disappears in the nanocomposite samples. The dynamic mechanical analysis results show the enhanced storage modulus and transition temperature compared with the pristine polymer. At the glass transition temperature, the storage modulus of nanocomposites is in the range of 17–79 MPa, whereas the pristine polymer shows a storage modulus of 2.1 MPa. The melting peak temperature ranges from 230 to 260°C, which is further confirmed by thermogravimetric analysis (TGA) results. The samples are stable up to 200°C and show a two‐stage degradation. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

The effect of organic modifier‐12‐aminolauric acid on morphology and thermal properties of polylactide nanocomposites

A novel organically modified montmorillonite (OMMT) based on a bifunctional organic modifier‐12‐aminolauric acid (ALA) was synthesized. Polylactide (PLA) nanocomposites with this new and traditional OMMT were prepared by solution casting method. The effects of the organic modifiers on structure, morphology and thermal properties of PLA nanocomposites have been investigated using Fourier transform infrared spectroscopy (FTIR), X‐ray diffraction (XRD), transmission electron microscopy (TEM), and thermogravimetric analysis (TGA). The results indicate that ALA has distinct effects on the dispersion of MMT platelets into the PLA matrix, where partial exfoliated as well as intercalated structures have been obtained, when compared with ordinary modifier, cetyltrimethyl ammonium bromide (CTAB). TGA data verifies that PLA nanocomposites with ALA‐MMT organoclay display enhanced thermal stability. The optimal clay loading of ALA‐MMT occurs at 3%wt, leading to the best compromise between clay dispersion and thermal properties. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

Effect of organic modifiers and silicate type on filler dispersion,thermal, and mechanical properties of ABS‐clay nanocomposites

Acrylonitrile–butadiene–styrene (ABS)–clay composite and intercalated nanocomposites were prepared by melt processing, using Na‐montmorillonite (MMT), several chemically different organically modified MMT (OMMT) and Na‐laponite clays. The polymer–clay hybrids were characterized by WAXD, TEM, DSC, TGA, tensile, and impact tests. Intercalated nanocomposites are formed with organoclays, a composite is obtained with unmodified MMT, and the nanocomposite based on synthetic laponite is almost exfoliated. An unintercalated nanocomposite is formed by one of the organically modified clays, with similar overall stack dispersion as compared to the intercalated nanocomposites. T_g of ABS is unaffected by incorporation of the silicate filler in its matrix upto 4 wt % loading for different aspect ratios and organic modifications. A significant improvement in the onset of thermal decomposition (40–44°C at 4 wt % organoclay) is seen. The Young's modulus shows improvement, the elongation‐at‐break shows reduction, and the tensile strength shows improvement. Notched and unnotched impact strength of the intercalated MMT nanocomposites is lower as compared to that of ABS matrix. However, laponite and overexchanged organomontmorillonite clay lead to improvement in ductility. For the MMT clays, the Young's modulus (E) correlates with the intercalation change in organoclay interlayer separation (Δd₀₀₁) as influenced by the chemistry of the modifier. Although ABS‐laponite composites are exfoliated, the intercalated OMMT‐based nanocomposites show greater improvement in modulus. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Poly(vinyl alcohol) nanocomposites with different clays: Pristine clays and organoclays

Poly(vinyl alcohol) (PVA)/clay nanocomposites were synthesized using the solution intercalation method. Na ion‐exchanged clays [Na⁺–saponite (SPT) and Na⁺–montmorillonite (MMT)] and alkyl ammonium ion‐exchanged clays (C₁₂–MMT and C₁₂OOH–MMT) were used for the PVA nanocomposites. From the morphological studies, the Na ion‐exchanged clay is more easily dispersed in a PVA matrix than is the alkyl ammonium ion‐exchanged clay. Attempts were also made to improve both the thermal stabilities and the tensile properties of PVA/clay nanocomposite films, and it was found that the addition of only a small amount of clay was sufficient for that purpose. Both the ultimate tensile strength and the initial modulus for the nanocomposites increased gradually with clay loading up to 8 wt %. In C₁₂OOH–MMT, the maximum enhancement of the ultimate tensile strength and the initial modulus for the nanocomposites was observed for blends containing 6 wt % organoclay. Na ion‐exchanged clays have higher tensile strengths than those of organic alkyl‐exchanged clays in PVA nanocomposites films. On the other hand, organic alkyl‐exchanged clays have initial moduli that are better than those of Na ion‐exchanged clays. Overall, the content of clay particles in the polymer matrix affect both the thermal stability and the tensile properties of the polymer/clay nanocomposites. However, a change in thermal stability with clay was not significant. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3208–3214, 2003