Structural effect of photoinitiators on electro‐optical properties of polymer‐dispersed liquid crystal composite films

Two types of photoinitiators were synthesized: (1) a α,ω‐telechelic oligomeric photoinitiator, by the reaction of poly(propylene glycol) diglycidylether (PPGDGE) and 2‐hydroxy‐2‐methyl‐1‐phenyl‐propan‐1‐one (Darocur 1173), and (2) a polymeric photoinitiator, by copolymerization of a monomer that had a liquid crystalline property, 4‐[ω‐(2‐methylpropenoyloxy)decanoxy]‐4′‐cyanobiphenyl, with a vinyl monomer that had a photosensitive group. For comparison, low‐molecular‐weight (low‐MW) photoinitiator (Darocur 1173) also was used. Attention was directed to the structural effect of the photoinitiators on the electro‐optical properties of polymer‐dispersed liquid crystal (PDLC) film in which the LC phase occupied a major volume (80 wt % of the composite film). For the preparation of PDLC films by the polymerization‐induced phase separation method, the optimum UV‐curing temperature was observed at 50°C, a temperature slightly higher than the cloud temperature (T_cloud) of the low‐MW LC/matrix‐forming material mixture. It was found that the electro‐optical performance of the PDLC cell fabricated with the oligomeric or polymeric photoinitiator was better than that of the PDLC cell made with a low‐MW photoinitiator (Darocur 1173), exhibiting lower driving voltage (V₉₀) and higher contrast ratio under identical formulation conditions. Oligomeric photoinitiators allowed premature phase separation between the LC and matrix phases, resulting in relatively pure LC‐rich phases. For the polymeric photoinitiator, incorporation of mesogenic moieties into the photoinitiator resulted in not only a well‐defined LC/matrix morphology but also in low driving voltage (V₉₀) because of reduced friction at the LC/matrix interfaces. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 162–169, 2006     

Macro reversible addition–fragmentation chain transfer agent mixture as a means to enhance the electro‐optical performance of polymer‐dispersed liquid crystals

Macro reversible addition–fragmentation chain transfer (RAFT) agents, i.e. RAFT polystyrene (RAFT‐PS) and RAFT poly(n‐butyl acrylate) (RAFT‐PBA), were mixed. Polymer‐dispersed liquid crystals (PDLCs) were prepared using the mixture together with methyl acrylate and liquid crystal E7. The electro‐optical properties of the PDLCs obtained were investigated. The results showed that the advantages of the electro‐optical properties of RAFT‐PS‐ and RAFT‐PBA‐dependent PDLCs could be combined in RAFT agent mixture‐dependent PDLCs. Copyright © 2011 Society of Chemical Industry     

Electro‐optical properties of polymer‐dispersed liquid crystal prepared by controlled graft living radical polymerization

Living graft macromolecule has been prepared through reversible addition‐fragmentation chain transfer (RAFT) living radical polymerization in one step. Then, it was used to make polymer‐dispersed liquid crystal (PDLC) by controlling the mole ratio of styrene (St) to 1,6‐hexanediol diacrylate (HDDA) and adjusting the content of prepared graft macromolecule. The results showed that electro‐optical properties of PDLC have been optimized. Different concentration of living graft macromolecule and different mole ratio of St/HDDA led to substantial improvement of driving voltage (threshold voltage and saturation voltage) and memory effect of PDLC simultaneously. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

An investigation into the morphology and electro‐optical properties of 2‐hydroxy ethyl methacrylate polymer dispersed liquid crystals

Polymer dispersed liquid crystal (PDLC) films are fabricated using E7 liquid crystals, tetraethylene glycol diacrylate (TeGDA) crosslinking agent, and 0–66.49 mol % 2‐hydroxy ethyl methacrylate (HEMA). The effects of different levels of HEMA addition on the microstructure and electro‐optical properties of the PDLC samples are examined using scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, and UV‐Vis spectroscopy, respectively. The results show that the refractive index of the PDLC films is insensitive to the level of HEMA addition. However, an increasing HEMA content improves the degree of phase separation during the polymerization process and increases the size and uniformity of the liquid crystal domain. As a result, the electro‐optical properties of the PDLC films are significantly improved as the level of HEMA addition is increased. Overall, the results show that a PDLC comprising 40 wt % E7 liquid crystals, 33.51 mol % TeGDA and 66.49 mol % HEMA has a high contrast ratio (13 : 1) and a low driving voltage (10 V) and is therefore an ideal candidate for a wide variety of intelligent photoelectric applications. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Direct electrochemical regeneration of enzymatic cofactor 1,4‐NADH on a cathode composed of multi‐walled carbon nanotubes decorated with nickel nanoparticles

Multi‐walled carbon nanotubes (MWCNTs) were grown on a stainless steel mesh and decorated with nickel nanoparticles (Ni NPs). The developed Ni NP‐MWCNT material was then used as a cathode in an electrochemical batch reactor to electrocatalytically convert NAD⁺ to enzymatically‐active 1,4‐NADH. The regeneration of 1,4‐NADH was studied at various electrode potentials. At electrode potential of ?1.6 V, a very high recovery (relative amount of 1,4‐NADH in the product mixture) was obtained, 98 ± 1 %. In comparison, to achieve the same recovery on a non‐decorated MWCNT cathode, a much higher cathodic potential was needed (?2.3 V), establishing the importance of Ni NPs on the electrocatalytic activity in reducing NAD⁺ to 1,4‐NADH. It was postulated that hydrogen adsorbs on Ni NPs immobilized on MWCNTs to form Ni‐H_ads, and this activated hydrogen rapidly reacts with neighbouring NAD‐radicals, preventing the dimerization of the latter species, ultimately yielding 1,4‐NADH.     

The improvement of electro‐optical properties of polymer‐dispersed liquid crystals with graft copolymer matrix synthesized by reversible addition–fragmentation chain transfer and atom transfer radical polymerization

Aiming to decrease the memory effect of polymer‐dispersed liquid crystals (PDLCs), a type of graft macroinitiator, synthesized by reversible addition–fragmentation chain transfer and atom transfer radical polymerization, was employed to prepare PDLCs with graft copolymer matrix in our previous work. Compared with linear copolymer matrix PDLCs prepared using a linear macroinitiator, it was found that, although low‐memory‐effect PDLCs were obtained, the driving voltage and transmittance of the PDLCs were unfortunately sacrificed to some extent. Thus, it is necessary to improve the electro‐optical properties of PDLCs on the basis of the original research performed by us. In the work reported in this article, a kind of linear macroinitiator with high refractive index and another graft macroinitiator with flexible branched chains were employed to prepare PDLCs. The results showed that by using mixed macroinitiators, the electro‐optical properties of PDLCs could be improved, and a possible mechanism is proposed.     

Preparation of polymer‐dispersed liquid crystal films containing a small amount of liquid crystalline polymer and their properties

Polymer‐dispersed liquid crystal (PDLC) films were synthesized by the copolymerization of liquid crystalline polymer (LCP) precursor, urethane acrylate (UA), and mesogenic monomer (AI) at different conditions. The morphology of polymer matrix changed with the weight ratio of polymer/liquid crystal (LC) ratio and curing temperature, resulting in a large change in the droplet size of LC domains in the PDLC film. The components used in the synthesis of polymer matrix, that is, the weight ratio of LCP, AI, and UA, also strongly influenced the morphology of PDLC films. A small amount of LCP was copolymerized with UA and AI in the preparation of polymer matrix to improve the electrooptical properties such as the viewing angle. Added LCP also affected the morphology and the properties of PDLC. The hydrophobicity of LCP caused changes in the droplet size of LC domain in PDLC films and the anchoring energy between matrix polymer and LC droplets. As the hydrophobicity of the matrix increases, the droplet size of LC domain also increases; on the contrary, anchoring energy decreased, leading to the decrease of driving voltage. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 3178–3188, 2000     

Comparative study on the electrooptical properties of polymer‐dispersed liquid crystal films with different mixtures of monomers and liquid crystals

This article deals with the study of polymer‐dispersed liquid crystal (PDLC) films that consisted of microdroplets of liquid crystals (LCs) dispersed in a polymer matrix. The PDLC films were fabricated by the photoinduced phase separation method under room‐temperature conditions. To determine the extent of the effects of the molecular structures and their physical properties of different mixtures of monomers and LCs on the morphology and electrooptical properties of the PDLC films, various mixtures were used. A detailed discussion of the obtained results is given. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Enhancement of dispersion of carbon nanotube and physical properties of poly(styrene‐co‐acrylonitrile)/multiwalled carbon nanotube nanocomposite via surface initiated ATRP

Dispersion behavior of multiwalled carbon nanotube (MWCNT), rheological and mechanical properties of various MWCNT/poly(styrene‐co‐acrylonitrile) (SAN) nanocomposites were investigated. MWCNT/SAN nanocomposites were prepared by three different methods; MWCNT/SAN melt blending, MWCNT/SAN in situ atom transfer radical polymerization (ATRP) and functionalized‐MWCNT/SAN in situ ATRP. Formation of SAN onto the surface of MWCNT and the molecular weight of grafted‐SAN were confirmed by fourier transform infrared spectra, ¹H‐NMR and ¹³C‐NMR. Crossover frequency of storage and loss modulus from rheological measurement and dynamic mechanical analysis showed that functionalized MWCNT/SAN in situ ATRP nanocomposite showed more uniform dispersion of MWCNT. Improved mechanical and electrical properties were observed for functionalized MWCNT/SAN in situ ATRP nanocomposite. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effect of a chiral dopant on the electro‐optical properties of polymer‐dispersed liquid‐crystal films

Polymer‐dispersed liquid crystal (PDLC) films were prepared by the ultraviolet‐light‐induced polymerization of photopolymerizable monomers in nematic liquid crystal/monomer/chiral dopant composites, and the effect of the chiral dopant on the electro‐optical properties of the PDLC films was studied. It was demonstrated that the addition of a small amount of the chiral dopant increased the driving voltage somewhat but decreased the turn‐off time significantly. Furthermore, the transmittance of ultraviolet, visible, and near‐infrared light of the off state of PDLC films showing light scattering increased with increasing content of the chiral dopant, and the optimum electro‐optical properties of the PDLC films were obtained when the content of the chiral dopant was not more than 2 wt %. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Synthesis and characterization of novel hybrid polyoxazoline‐grafted multiwalled carbon nanotubes

The novel hybrid polyoxazoline‐grafted multiwalled carbon nanotubes (POZO‐grafted MWNTs) were synthesized by the reaction of partially hydrolyzed polyoxazolines (Hydrolyzed‐POZO) and MWNTs having carboxylic acid groups (MWNT‐COOH) in the presence of DCC as a condensing agent. Hydrolyzed‐POZO (degree of hydrolysis, 20.2 mol % by ¹H‐NMR) were produced from the hydrolysis of polyoxazolines in an aqueous NaOH solution at reflux for 72 h. MWNT‐COOH were prepared by acid treatment of pristine MWNTs. The composition, structure, thermal property, and surface morphology of the novel hybrid POZO‐grafted MWNTs were fully characterized by FT‐IR, Raman, ¹H‐NMR, DSC, TGA, SEM, and TEM. The obtained POZO‐grafted MWNTs are well soluble in various organic solvents and water. It was observed that the glass transition temperature (T_g) of POZO‐grafted MWNTs was lower than that of Hydrolyzed‐POZO due to the absence of hydrogen bonding interactions between Hydrolyzed‐POZO itself caused by the incorporation with MWNTs. It was also found that Hydrolyzed‐POZO was homogeneously attached to the surfaces of MWNTs through the “grafting‐to” method. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

In situ polymerization and photophysical properties of poly(p‐phenylene benzobisoxazole)/multiwalled carbon nanotubes composites

Poly(p‐phenylene benzobisoxazole)/multiwalled carbon nanotubes (PBO‐MWCNT) composites with different MWCNT compositions were prepared through in situ polymerization of PBO in the presence of carboxylated MWCNTs. The nanocomposite's structure, thermal and photophysical properties were investigated and compared with their blend counterparts (PBO/MWCNT) using Fourier transform infrared spectra, Raman spectra, Wide‐angle X‐ray diffraction, thermogravimetric analysis, UV‐vis absorption, and photoluminescence. The results showed that MWCNTs had a strong interaction with PBO through covalent bonding. The incorporation of MWCNTs increased the distance between two neighboring PBO chains and also improved the thermal resistance of PBO. The investigation of UV‐vis absorption and fluorescence emission spectra exhibited that in situ PBO‐MWCNT composites had a stronger absorbance and obvious trend of red‐shift compared with blend PBO/MWCNT composites for all compositions. This behavior can be attributed to the efficient energy transfer through forming conjugated bonding interactions in the PBO‐MWCNT composites. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Optimization of LC droplet size and electro‐optical properties of acrylate‐based polymer‐dispersed liquid crystal by controlling photocure rate

We investigated the effects of the different content ratios of 2‐ethylhexylacrylate (2‐EHA) and 2‐ethylhexylmethacrylate (2‐EHMA) on the relationships among the photopolymerization rate, morphology of liquid crystals (LCs) droplets, and electro‐optical properties of trifunctional urethane acrylate‐based polymer‐dispersed liquid crystal (PDLC) systems. Photo‐differential scanning calorimetry (DSC) analysis and resistivity measurement revealed that increasing 2‐EHMA content gradually decreased the photocure rate of trifunctional urethane acrylate‐based PDLCs, which prolonged the phase separation between the LC molecules and the prepolymers. Morphological observations and electro‐optical measurements demonstrated that trifunctional urethane acrylate‐based PDLCs with the 2‐EHA:2‐EHMA ratios from 4:1 to 3:2 in weight percent formed the favorable microstructures of LC droplets being within the range of 1–5 µm to scatter light efficiently and showed the satisfactory off‐state opacity and on‐state transmittance and the relatively low‐driving voltage. The microstructures of LC droplets and electro‐optical properties of trifunctional urethane acrylate‐based PDLCs could be usefully optimized by controlling the photocure rate using the different 2‐EHA/2‐EHMA content ratios. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 3098–3104, 2013     

Synthesis of multiwalled carbon nanotubes on Al2O3 supported Ni catalysts in a fluidized‐bed

Multiwalled carbon nanotubes (MWNTs) were synthesized on Al₂O₃ supported Ni catalysts from C₂H₂ and C₂H₄ feedstocks in a fluidized bed. The influence of the ratio of superficial gas velocity to the minimum fluidization velocity (U/U_mf), feedstock type, the ratio of carbon in the total quantity of gas fed to the reactor, reaction temperature, the ratio of hydrogen to carbon in the feed gas, and nickel loading were all investigated. Significantly, the pressure drop across the fluidized‐bed increased as the reaction time increased for all experiments, due to the deposition of MWNTs on the catalyst particles. This resulted in substantial changes to the depth and structure of the fluidized bed as the reaction proceeded, significantly altering the bed hydrodynamics. TEM images of the bed materials showed that MWNTs, metal catalysts, and alumina supports were predominant in the product mixture, with some coiled carbon nanotubes as a by‐product. © 2009 American Institute of Chemical Engineers AIChE J, 2009     

The plasticizer‐assisted formation of a percolating multiwalled carbon nanotube network in biodegradable poly(L‐lactide)

A plasticizer, polyethylene glycol (PEG), was used to disperse multiwalled carbon nanotubes (MWCNTs) in biodegradable poly(L ‐lactide) during one‐step melt mixing. Incorporation of PEG significantly promotes the formation of a percolating MWCNT network in the plasticized composites, as revealed by rheological measurements and morphological observations. It, in turn, results in the retarded glass transition and cold crystallization behaviors in these plasticized composites as a result of constrained chain relaxation. It is believed that noncovalent wrapping of MWCNTs by PEG is responsible for the improved affinity between MWCNTs and the poly(L ‐lactide) matrix. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Electro–optic studies on polymer‐dispersed liquid crystal composite films. I. Composites of PVB–E7

The electro‐optic performance characteristic of polymer‐dispersed liquid crystal (PDLC) composite films out of poly(vinyl butyral) (PVB) and nematic liquid crystal (E7) have been studied for a wide range of PVB–E7 composite compositions (20–70 wt % of E7). Composites were prepared by solvent casting from chloroform at room temperature. A scanning electron microscopy study showed that a E7 phase is continuously embedded in chink‐like structure of PVB matrix. Optical transmittance of the composite films (of 60 and 70 wt % loading of E7) under an alternating current (ac) electric field (0–250, V_p‐p) and frequency (50 Hz to 1 KHz) were measured employing He Ne laser (λ = 632.8 nm). The results indicate that the (PVB–E7) composite exhibits a memory effect. In the memory state, higher transmittance is preserved without applying voltage. The memory state can be erased and changed to the scattering Off‐state by heating the film to the clearing temperature of the liquid crystal. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 3485–3491, 1999     

Electrochemical immobilization of ascorbate oxidase in poly(3,4‐ethylenedioxythiophene)/multiwalled carbon nanotubes composite films

Immobilization of ascorbate oxidase (AO) in poly(3,4‐ethylenedioxythiophene) (PEDOT)/multiwalled carbon nanotubes (MWCNTs) composite films was achieved by one‐step electrochemical polymerization. The PEDOT/MWCNTs/AO modified electrode was fabricated by the entrapment of enzyme in conducting matrices during electrochemical polymerization. The PEDOT/MWCNTs modified electrodes were investigated by cyclic voltammetry and electrochemical impedance spectroscopy. The experimental results showed that the composite films exhibited better mechanical integrity, electrochemical activity, higher electronic and ionic conductivity, and larger redox capacitance compared with pure PEDOT films, which would be beneficial to the fabrication of PEDOT/MWCNTs/AO electrochemical biosensors. The scanning electron microscopy studies revealed that MWCNTs served as backbone for 3,4‐ethylenedioxythiophene (EDOT) electropolymerization. Furthermore, the resulting enzyme electrode could be used to determine L ‐ascorbic acid successfully, which demonstrated the good bioelectrochemical catalytic activity of the immobilized AO. The results indicated that the PEDOT/MWCNTs composite are a good candidate material for the immobilization of AO in the fabrication of enzyme‐based biosensor. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effects of thermal imidization on mechanical properties of poly(amide‐co‐imide)/multiwalled carbon nanotube composite films

In this study, experimental and numerical studies were performed to investigate the relationship among the functionalization method, weight fraction of MWCNTs, thermal imidization cycle, and mechanical properties of various PAI/MWCNT composite films. Poly(amide‐co‐imide)/multiwalled carbon nanotube composite films were prepared by solution mixing and film casting. The effects of chemical functionalization and weight fraction of multiwalled carbon nanotubes on thermal imidization and mechanical properties were investigated through experimental and numerical studies. The time needed to achieve sufficient thermal imidization was reduced with increasing multiwalled carbon nanotube content when compared with that of a pure poly(amide‐co‐imide) film because multiwalled carbon nanotubes have a higher thermal conductivity than pure poly(amide‐co‐imide) resin. Mechanical properties of pure poly(amide‐co‐imide) and poly(amide‐co‐imide)/multiwalled carbon nanotube composite films were increased with increasing imidization time and were improved significantly in the case of the composite film filled with hydrogen peroxide treated multiwalled carbon nanotubes. Both the tensile strength and strain to failure of the multiwalled carbon nanotube filled poly(amide‐co‐imide) film were increased substantially because multiwalled carbon nanotube dispersion was improved and covalent bonding was formed between multiwalled carbon nanotubes and poly(amide‐co‐imide) molecules. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Superior reinforcement in polyamide 1010/multiwalled carbon nanotube composites realized by high‐rate drawing and incorporation of compatibilizer

To realize the full potential of carbon nanotubes (CNTs) in polymer/CNT nanocomposites, many complicated chemical treatments have been developed to modify the CNTs. Nevertheless, the reinforcing efficiency is still not satisfactory in most cases. In this study, a dramatically improved mechanical enhancement is obtained for polyamide 1010/multiwalled carbon nanotube (MWNT) composites simply by exerting high‐rate drawing and incorporating a commercially available compatibilizer. For the fibers prepared at high draw ratio, their tensile strength and modulus are improved by 137 and 132%, respectively, through adding only 0.5 wt% MWNTs. In particular, the increase in strength is at a very high level for the case of non‐covalent interaction since CNTs could be stretched to failure according to theoretical calculation. It is demonstrated that this reinforcement is mainly attributed to the compatibilizer inducing good dispersion, and the high‐rate drawing inducing strong interfacial interaction and orientation of MWNTs. Copyright © 2012 Society of Chemical Industry     

Nucleation effect of hydroxyl‐purified multiwalled carbon nanotubes in poly(p‐phenylene sulfide) composites

To investigate the nucleation effect of hydroxyl‐purified multiwalled carbon nanotubes (MWNTs‐OH) in poly(p‐phenylenesulfide) (PPS), a series of composites were prepared by blending PPS with MWNTs‐OH at 1, 2, and 3 wt %, respectively. Under SEM observation MWNTs‐OH were found homogeneously dispersed in the PPS matrix. DSC thermograms revealed that the enthalpy (ΔH_c) of the composites increased with increasing MWNT‐OH content, whereas the crystallization temperature (T_c) decreased progressively. The decrease in T_c was in accordance with the smaller crystallite size determined with WXRD characterization, and the increase in ΔH_c was evidenced by FTIR and XPS analyses. The higher ΔH_c shows that MWNTs‐OH serves as a nucleating agent, providing sufficiently multiplied sites for crystal growth. The lowering of T_c was attributed not only to MWNTs‐OH network hindrance to PPS chain fusing rearrangement, but also to a poorer affinity between MWNTs‐OH and PPS; both effects coordinately govern T_c of PPS/MWNTs‐OH composites. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013