Fabrication,characterization, and properties of poly(ethylene‐co‐vinyl acetate)/magnetite nanocomposites

Poly(ethylene‐co‐vinyl acetate) (EVA)/magnetite (Fe₃O₄) nanocomposite was prepared with different loading of Fe₃O₄ nanoparticles. The mixing and compounding were carried out on a two‐roll mixing mill and the sheets were prepared in a compression‐molding machine. The effect of loading of nanoparticles in EVA was investigated thoroughly by different characterization technique such as transmission electron microscopy (TEM), X‐ray diffraction (XRD), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), limiting oxygen index (LOI), and technological properties. TEM analysis showed the uniform dispersion of filler in the polymer matrix and the dispersion of filler decreased with increase in filler content. XRD of the nanocomposite revealed the more ordered structure of the polymer chain. An appreciable increase in glass transition temperature was observed owing to the restricted mobility of Fe₃O₄‐filled EVA nanocomposite. TGA and flame resistance studies indicated that the composites attain better thermal and flame resistance than EVA owing to the interaction of filler and polymer segments. Mechanical properties such as tensile strength, tear resistance, and modulus were increased for composites up to 7 phr of filler, which is presumably owing to aggregation of Fe₃O₄ nanoparticle at higher loading. The presence of Fe₃O₄ nanoparticles in the polymer matrix reduced the elongation at break and impact strength while improved hardness of the composite than unfilled EVA. The change in technological properties had been correlated with the variation of polymer–filler interaction estimated from the swelling behavior. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40116.     

A novel intumescent flame‐retardant system for flame‐retarded LLDPE/EVA composites

A new intumescent flame retardant (IFR) system consisting of ammonium polyphosphate (APP) and charing‐foaming agent (CFA) and a little organic montmorillonite (OMMT) was used in low‐density polyethylene (LLDPE)/ethylene‐vinyl acetate (EVA) composite. According to limiting oxygen index (LOI) value and UL‐94 rating obtained from this work, the reasonable mass ratio of APP to CFA was 3 : 1, and OMMT could obviously enhance the flame retardancy of the composites. Cone calorimeter (CONE) and thermogravimetric analysis (TGA) were applied to evaluate the burning behavior and thermal stability of IFR‐LLDPE/EVA (LLDPE/EVA) composites. The results of cone calorimeter showed that heat release rate peak (HRR‐peak) and smoke production rate peak (SPR‐peak) and time to ignition (TTI) of IFR‐LLDPE/EVA composites decreased clearly compared with the pure blend. TGA data showed that IFR could enhance the thermal stability of the composites at high temperature and effectively increase the char residue. The morphological structures of the composites observed by scanning electron microscopy (SEM) and X‐ray diffraction (XRD) demonstrated that OMMT could well disperse in the composites without exfoliation, and obviously improve the compatibility of components of IFR in LLDPE/EVA blend. The morphological structures of char layer obtained from Cone indicated that OMMT make the char layer structure be more homogenous and more stable. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effect of electron beam irradiation on (waste tire dust)‐filled ethylene vinyl acetate in the presence of bisphenol a diglycidyl ether

The effect of bisphenol A diglycidyl ether (BADGE) and electron beam (EB) irradiation on the properties of waste tire dust (WTD) ‐filled ethylene vinyl acetate (EVA) has been studied. The EVA/WTD ratio was fixed to 80:20, whereas the BADGE concentration varied from 1 to 5 wt%. The samples were then irradiated using a 3.0‐MeV EB machine at 50 kGy to 200 kGy at increments of 50 kGy. All the samples were subjected to various mechanical, physical, and thermal tests. Prior to irradiation, the mechanical properties of the composites show a gradual decrease with increasing BADGE concentration. Such observation is attributed to the plasticizing effect of the BADGE, as indicated by the reduction in mixing torque and a 14% increase in the elongation at break with the addition of 5 wt% BADGE. Results of gel fraction indicated that BADGE did not accelerate the irradiation‐induced crosslinking of EVA/WTD composites. The scanning electron micrographs and tan δ curves of EVA/WTD composites showed evidence that the addition of BADGE and EB irradiation of the EVA/WTD improves the compatibility of the composite. The overall results revealed that the irradiated EVA/WTD composite without BADGE gives a better enhancement in mechanical properties compared with the composites incorporated with the BADGE. J. VINYL ADDIT. TECHNOL., 23:172–180, 2017. © 2015 Society of Plastics Engineers     

Effect of the particle size of expandable graphite on the thermal stability,flammability, and mechanical properties of high‐density polyethylene/ethylene vinyl‐acetate/expandable graphite composites

In this article, high‐density polyethylene/ethylene vinyl‐acetate copolymer (HDPE/EVA) composites filled with two different particle sizes (45 and 150 µm) of expandable graphite (EG) were prepared by using a twin‐screw extruder. The thermal stability, flammability, and mechanical properties of HDPE/EVA/EG composites were investigated by thermogravimetric analysis (TGA), cone calorimeter test (CCT), tensile test, and scanning electron microscopy (SEM). The results from TGA and CCT indicated that EG significantly enhanced the thermal stability and fire resistance of HDPE/EVA blend. The thermal stability and flame retardancy of HDPE/EVA/EG composites were improved with decreasing particle size of EG. Although the onset of weight loss of the flame‐retardant composites occurred at a lower temperature than that of HDPE/EVA blend, the flame‐retardant composites produced a large amount of char residue at a high temperature. The consolidated char layer formed a barrier, which could reduce heat, low‐molecular transfer, and air incursion, and thus enhanced the flame retardancy. The data from the tensile test showed that the addition of EG deteriorated the mechanical properties; however, the tensile stress and strain of HDPE/EVA/EG composites increased with decreasing the particle size of EG owing to the strong interface adhesion between polymer matrix and inorganic particles. POLYM. ENG. SCI., 54:1162–1169, 2014. © 2013 Society of Plastics Engineers     

Preparation and characterization of EVA–sisal fiber composites

In this work, composites of an EVA polymer matrix and short sisal fiber were characterized. The physical‐morphological as well as chemical interactions between EVA and sisal were investigated. When the samples were prepared in the presence of dicumyl peroxide, the results suggest that crosslinking of EVA as well as grafting between EVA and the sisal fibers took place. Morphological changes were studied by scanning electron microscopy (SEM). Results from Hg‐porosimetry, SEM, Fourier transform infrared spectroscopy, surface free energy, and gel content strongly indicate grafting of EVA onto sisal under the composite preparation conditions, even in the absence of peroxide. The grafting mechanism could not be confirmed from solid‐state ¹³C NMR analysis. The grafting had an impact on the thermal and mechanical properties of the composites, as determined by differential scanning calorimetry and tensile testing. Thermogravimetric analysis results show that the composites are more stable than both EVA and sisal fiber alone. The composite stability, however, decreases with increasing fiber content. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1607–1617, 2006     

Investigation of the thermal,mechanical and morphological properties of poly(vinyl chloride)/polyhedral oligomeric silsesquioxane nanocomposites

Research into organic–inorganic nanocomposites has recently become popular, particularly the development of new polymer nanocomposites. Compared to pristine polymers or conventional composites, these nanocomposites exhibit improved properties. The storage modulus of a poly(vinyl chloride) (PVC)/polyhedral oligomeric silsesquioxane (POSS) nanocomposite slightly decreased with POSS content, but had a higher modulus from 50 to 100 °C. Some of the material appeared to be aggregated with 1 wt% POSS in the polymeric matrix. Conversely, with a POSS content of 5 wt%, a better dispersion of the nanoparticles was observed. The presence of POSS in the plasticised PVC compound had little influence on the final properties of the nanocomposites, showing weaker interactions between the POSS and the plasticised PVC compound. Copyright © 2010 Society of Chemical Industry     

The grafting reaction of epoxycyclohexyl polyhedral oligomeric silsesquioxanes with carboxylic methoxypolyethylene glycols and the properties of composite solid polymer electrolytes with the graftomer

A novel organic–inorganic hybrid of epoxycyclohexyl polyhedral oligomeric silsesquioxane (e‐POSS)–grafted carboxylic methoxypolyethylene glycols (mPEG‐COOH), that is, a POSS‐mPEG graftomer, was synthesized. The grafting reaction of e‐POSS and mPEG‐COOH was characterized by Fourier transform infrared (FTIR) and ¹H‐NMR spectroscopy. Then the graftomer was used to develop new composite solid polymer electrolyte (SPE) films with a carboxylated nitrile rubber–epoxidized natural rubber (XNBR‐ENR) self‐crosslinked blend system as a dual‐phase polymer matrix. The self‐crosslinked reaction of the XNBR‐ENR matrix was investigated using ATR‐FTIR. The morphology of the SPE films and the distribution of lithium salt were investigated using field emission scanning electron microscopy and X‐ray diffraction, and the result illustrated that the addition of POSS‐mPEG could promote and accelerate the dissociation of LiClO₄. The best effect within the range of this study was achieved when 25 phr POSS‐mPEG was involved. The differential scanning calorimetry analysis proved that the glass‐transition temperature of the composite SPE films was reduced with the increase of POSS‐mPEG. The ionic conductivity of the composite SPE films was investigated by electrochemical impedance spectroscopy. The highest ionic conductivity in this study of 2.57 × 10^?5 S cm^?1 was obtained with 25 phr POSS‐mPEG loading. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44460.     

Morphology and thermal properties of maleic anhydride grafted polypropylene/ethylene–vinyl acetate copolymer/wood powder blend composites

Maleic anhydride grafted polypropylene (MAPP) was blended with ethylene–vinyl acetate (EVA) copolymer to form MAPP/EVA polymer blends. Wood powder (WP) was mixed into these blends at different weight fractions to form MAPP/EVA/WP blend composites. Differential scanning calorimetry (DSC) analysis of the blends showed small melting peaks between those of EVA and MAPP, which indicated interaction and cocrystallization of fractions of EVA and MAPP. The presence of MAPP influenced the EVA crystallization behavior, whereas the MAPP crystallization was not affected by the presence of EVA. Scanning electron microscopy, Fourier transform infrared spectroscopy, and DSC results show that the WP particles in the MAPP/EVA blend were in contact with both the MAPP and EVA phases and that there seemed to be chemical interaction between the different functional groups. This influenced the crystallization behavior, especially of the MAPP phase. The thermogravimetric analysis results show that the MAPP/EVA blend had two degradation steps. An increase in the WP content in the blend composite led to an increase in the onset of the second degradation step but a decrease in onset of the first degradation step. The presence of WP in the blend led to an increase in the modulus but had almost no influence on the tensile strength of the blend. The dynamic mechanical analysis results confirm the interaction between EVA and MAPP and show that the presence of WP only slightly influenced the dynamic mechanical properties. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Comparison of Exfoliated Graphite Nanoplatelets (xGnP) and CNTs for Reinforcement of EVA Nanocomposites Fabricated by Solution Compounding Method and Three Screw Rotating Systems

Exfoliated graphite nanoplatelet (xGnP?) and carbon nanotube (CNT)-reinforced ethylene vinyl acetate (EVA) nanocomposites have been fabricated by three screw rotating systems: co-, counter- and modified-co-rotating. The highest tensile strength and modulus were shown by the composites, both xGnP- and CNT-loaded, made by counter-rotating. The counter-rotating process produced better dispersion than the other two as found in morphology studies by environmental scanning electron microscopy (ESEM). However, the rotating system did not affect the electrical conductivity. The percolation threshold of the xGnP–EVA nanocomposites formed by solution mixing and injection molding was between 14–16 wt%, due to the advantageous effect of sheets with higher aspect ratios compared with spherical or elliptical fillers in forming conducting networks in the polymer matrix. Although CNT–EVA was electrically conductive with only 5 wt% CNT loading, we recommend xGnP as a more suitable additive material for polymer composites. xGnP greatly increased the thermal stability of xGnP–EVA composites to be applied as adhesives, films and cables.     

Ethylene vinyl acetate/ethylene propylene diene terpolymer‐blend‐layered double hydroxide nanocomposites

Ethylene vinyl acetate (EVA‐45)/ethylene propylene diene terpolymer (EPDM) blend‐layered double hydroxide (LDH) nanocomposites have been prepared by solution blending of 1:1 weight ratio of EVA and EPDM with varying amounts of organo LDH (DS‐LDH). X‐ray diffraction and transmission electron microscopy analysis suggest the formation of partially exfoliated EVA/EPDM/DS‐LDH nanocomposites. Measurement of mechanical properties of the nanocomposites (3 wt% DS‐LDH content) show that the improvement in tensile strength and elongation at break are 35 and 12% higher than neat EVA/EPDM blends. Dynamic mechanical thermal analysis also shows that the storage modulus of the nanocomposites at glass transition temperature is higher compared to the pure blend. Such improvements in mechanical properties have been correlated in terms of fracture behavior of the nanocomposites using scanning electron microscopy analysis. Thermal stability of the prepared nanocomposites is substantially higher compared to neat EVA/EPDM blend, confirming the formation of high‐performance polymer nanocomposites. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Use of pyrolyzed oil shale as filler in poly(ethylene‐co‐vinyl acetate) with different vinyl acetate contents

Pyrolyzed oil shale (POS) obtained from the pyrolysis of bituminous rock was used as filler in poly(ethylene‐co‐vinyl acetate) (EVA). The effects of the VA content of EVA and the particle size of POS on the mechanical properties were investigated. The composites were prepared in a rotor mixer at 180°C with a concentration of POS of up to 30 wt %. The stress–strain plots of the compression‐molded composites are similar to the EVA (18% VA content) behavior for low concentrations (1–5 wt %) of POS with a particle size lower than 270 mesh. It was observed that decreasing the POS particle size and increasing the VA content of EVA produced better compatibility between the polymer and filler. The mechanical properties, differential scanning calorimetry, and dynamic mechanical analysis also demonstrated the compatibility between EVA and POS under the increase of the VA content in the EVA. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1544–1555, 2002; DOI 10.1002/app.10494     

Mechanical,morphological, and thermal properties of poly(vinyl chloride)/low‐density polyethylene composites filled with date palm leaf fiber

This article investigates the mechanical, morphological, and thermal properties of poly(vinyl chloride) (PVC) and low‐density polyethylene (LDPE) blends, at three different concentrations: 20, 50, and 80 wt% of LDPE. Besides, composite samples that were prepared from PVC/LDPE blend reinforced with different date palm leaf fiber (DPLF) content, 10, 20, and 30 wt%, were also studied. The sample in which PVC/LDPE (20 wt%/80 wt%) had the greatest tensile strength, elongation at break, and modulus. The good thermal stability of this sample can be seen that T_10% and T_20% occurred at higher temperatures compared to others blends. DPLF slightly improved the tensile strength of the polymer blend matrix at 10 wt% (C10). The modulus of the composites increased significantly with increasing filler content. Ageing conditions at 80°C for 168 h slightly improved the mechanical properties of composites. Scanning electron microscopic micrographs showed that morphological properties of tensile fracture surface are in accordance with the tensile properties of these blends and composites. Thermogravimetric analysis and derivative thermogravimetry show that the thermal degradation of PVC/LDPE (20 wt%/80 wt%) blend and PVC/LDPE/DPLF (10 and 30 wt%) composites took place in two steps: in the first step, the blend was more stable than the composites. In the second step, the composites showed a slightly better stability than the PVC/LDPE (20 wt%/80 wt%) blend. Based on the above investigation, these new green composites (PVC/LDPE/DPLF) can be used in several applications. J. VINYL ADDIT. TECHNOL., 25:E88–E93, 2019. © 2018 Society of Plastics Engineers     

Effect of OMMTs on flame retardancy and thermal stability of poly(ethylene‐co‐vinyl acetate)/LDPE/magnesium hydroxide composites

The aim of this study was to prepare poly (ethylene‐co‐vinyl acetate) (EVA)/ low density polyethylene (LDPE)/magnesium hydroxide (MH) composites applicable in cable industry with required flame retardancy. For this reason, two types of organo‐modified montmorillonites (OMMT) with different surface polarites (Cloisite 15A and Cloisite 30B) at various concentrations, and also combination of these two OMMTs with overall loadings of 2 wt % and 5 wt % were used. The samples were compounded using a twin screw extruder with total (MH + OMMT) feeding of 55 wt % and 60 wt %. Limiting oxygen index (LOI) of the samples containing 2 wt % of OMMTs increased about 16% and dripping was suppressed according to vertical burning test (UL‐94V). Thermogravimetric results of EVA/LDPE/MH samples containing OMMT showed that the beginning of second step degradation was shifted about 50°C to higher temperatures. The composite tensile strength results showed enhancement by incorporating some amount of nanoclays with EVA/LDPE/MH composites. Scanning electron microscopy images confirmed that MH particles had better wetting by EVA matrix in presence of nanoclays. Oxidative induction time of the EVA/LDPE/MH/OMMT nanocomposites was 140 min, which was more than that of the samples without OMMT (20 min). Employing the equal weight ratios of the two OMMTs demonstrated a synergistic effect on flame retardancy of the samples according to the both tests results (LOI, UL‐94V). X‐ray diffraction analysis of the samples confirmed the intercalation/semiexfoliation structure of nanosilicate layers in the bulk of EVA/LDPE matrix. This led to longer elongation at break and thermal stability of Cloisite 15A based nanocomposites. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40452.     

High‐performance EMI shielding materials based on short carbon fiber‐filled ethylene vinyl acetate copolymer,acrylonitrile butadiene copolymer,and their blends

The composites of carbon fiber with EVA, NBR, and their blends have been made by melt mixing technique. Stress–strain plots of different composites show that the necking phenomenon is increasing with the increase in fiber concentration in the polymer matrix. The scanning electron microscopic analysis and swelling study exhibit poor interaction between the short carbon fiber and polymer matrix. The decrease in DC resistivity with the increase in short carbon fiber concentration has been explained on the basis of percolation theory. EMI SE increases slightly with the increase in frequency of electromagnetic radiation but increases sharply with the increase in fiber concentration. EMI SE also depends on blend composition and increases with the increase in EVA concentration in the blend. Return loss is decreasing but absorption loss is increasing with the increase in fiber loading. A linear relationship is observed between the EMI SE and thickness of the composites. The EMI SE is found to increase exponentially with the increase in conductivity of the composite. The permeability value is decreasing with the increase in frequency as well as fiber loading. Thermal properties of the composites have been evaluated by thermogravimetric analysis and dynamic mechanical analysis. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

Durability of glass‐fiber‐reinforced polymer nanocomposites in an alkaline environment

This study was conducted to determine the effect of clay content in GFRP (glass‐fiber‐reinforced polymer) composite samples as they were aged in an alkaline solution. Two kinds of GFRP composite samples were prepared. One was E‐glass‐fiber‐reinforced vinyl ester polymer, and the other was nano‐GFRP composites prepared with the addition of 1 and 2 wt% of montmorillonite clay to the polymer matrix. These samples were aged in alkaline solution of pH 13.2 with and without sustained load. The load was 1335 N or 18.7% of the tensile strength of the composite samples. The aging was evaluated by measuring the reduction in tensile strength after 6 months. Also, absorption of alkaline solution into the plain and nano‐GFRP samples was investigated so as to elucidate the diffusion behaviors. It was found that for a short exposure time (e.g. 1 month) and without sustained load, dispersing 2 wt% of the nanoclay in the polymer matrix of the GFRP samples reduces the diffusivity by 39%. However, with the application of sustained load, the glass fiber composite samples deteriorate more with increasing clay content. The reduction in tensile strength was 7.1%, 12.1%, and 18.1% for the samples containing 0, 1, and 2 wt% of clay, respectively. J. VINYL. ADDIT. TECHNOL., 12:25–32, 2006. © 2006 Society of Plastics Engineers     

Influence of the pentaerythritol phosphate melamine salt content on the combustion and thermal decomposition process of intumescent flame‐retardant ethylene–vinyl acetate copolymer composites

Pentaerythritol phosphate melamine salt (PPMS) as a single‐molecule intumescent fire retardant was synthesized and characterized. The influence of the PPMS content on the combustion and thermal decomposition processes of intumescent‐flame‐retardant (IFR) ethylene–vinyl acetate copolymer (EVA) composites was studied by limiting oxygen index (LOI) measurement, UL 94 rating testing, cone calorimetry, thermogravimetric analysis, and scanning electron microscopy. The LOI and UL 94 rating results illustrate that PPMS used in EVA improved the flame retardancy of the EVA composites. The cone calorimetry test results show that the addition of PPMS significantly decreased the heat‐release rate, total heat release, and smoke‐production rate and enhanced the residual char fire performance of the EVA composites. The IFR–EVA3 composite showed the lowest heat‐release and smoke‐production rates and the highest char residue; this means that the IFR–EVA3 composite had the best flame retardancy. The thermogravimetry results show that the IFR–EVA composites had more residual char than pure EVA; the char residue yield increased with increasing PPMS content. The analysis results for the char residue structures also illustrated that the addition of PPMS into the EVA resin helped to enhance the fire properties of the char layer and improve the flame retardancy of the EVA composites. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42148.     

Electrical properties and morphology of carbon black‐filled HDPE/EVA composites

The sensitive effect of weight ratio of the high‐density polyethylene (HDPE)/ethylene‐vinylacetate copolymer (EVA) on the electrical properties of HDPE/EVA/carbon black (CB) composites was investigated. With the EVA content increasing from 0 wt % to 100 wt %, an obvious change of positive temperature coefficient (PTC) curve was observed, and a U‐shaped insulator‐conductor‐insulator transition in HDPE/EVA/CB composites with a CB concentration nearby the percolation threshold was found. The selective location of CB particles in HDPE/EVA blend was analyzed by means of theoretical method and scanning electron micrograph (SEM) in order to explain the U‐shaped insulator‐conductor‐insulator transition, a phenomenon different from double percolation in this composite. The first significant change of the resistivity, an insulator‐conductor transition, occurred when the conductive networks diffused into the whole matrix due to the forming of the conductive networks and the continuous EVA phase. The second time significant change of the resistivity, a conductor‐insulator transition, appeared when the amorphous phase is too large for CB particles to form the conductive networks throughout the whole matrix. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Recycled milk pouch and virgin LDPE‐LLDPE‐based jute fiber composites

The present investigation deals with the thermo‐mechanical recycling of post consumer milk pouches (LDPE‐LLDPE blend) and its use as jute fiber composite materials for engineering applications. The mechanical, thermal, morphological, and dynamic‐mechanical properties of recycled milk pouch‐based jute fiber composites with different fiber contents were evaluated and compared with those of the virgin LDPE‐LLDPE/jute fiber composites. Effect of artificial weathering on mechanical properties of different formulated composites was determined. The recycled polymer‐based jute fiber composites showed inferior mechanical properties as well as poor thermal stability compared to those observed for virgin polymer/jute fiber composites. However, the jute‐composites made with (50:50) recycled milk pouch‐virgin LDPE‐LLDPE blend as polymer matrix indicated significantly superior properties in comparison to the recycled milk pouch/jute composites. Overall mechanical performances of the recycled and virgin polymeric composites were correlated by scanning electron microscopy (SEM). The dynamic mechanical analysis showed that storage modulus values were lower for recycled LDPE‐LLDPE/jute composites compared to virgin LDPE‐LLDPE/jute composites throughout the entire temperature range, but an increase in the storage modulus was observed for recycled‐virgin LDPE‐LLDPE/jute composites. POLYM. COMPOS. 28:78–88, 2007. © 2007 Society of Plastics Engineers     

Partially miscible poly(lactic acid)‐ blend‐poly(propylene carbonate) filled with carbon black as conductive polymer composite

BACKGROUND: Conductive polymer composites (CPCs) can be obtained by filling polymer matrices with electrically conductive particles, and have a wide variety of potential applications. In the work reported, the biodegradable polymer poly(lactic acid) (PLA) as a partially miscible blend with poly(propylene carbonate) (PPC) was used as a polymer matrix. Carbon black (CB) was used as the conducting filler. RESULTS: Fourier transform infrared spectroscopy revealed interactions between matrix and CB filler; this interaction was stronger in PPC‐blend‐CB than in PLA‐blend‐CB composites. A rheology study showed that low‐viscosity PPC could improve the fluidity of the CPCs, but decrease that of CB. With increasing CB content, the enforcement effect, storage modulus and glass transition temperature increased, but the elongation at break decreased. CPCs exhibited the lowest electrical percolation thresholds of 1.39 vol.% CB when the content of PPC in PLA‐blend‐PPC was 40 wt%. The conductivity of CPCs containing 5.33 vol.% CB and 40 wt% PPC reached 1.57 S cm^?1. Scanning electron microscopy revealed that CB exhibits a preference for dispersion in the low‐viscosity phase (PPC) of the multiphase matrix. CONCLUSION: In the presence of CB, partially miscible PLA‐blend‐PPC could form multi‐percolation CPCs. Moreover, the combination of PLA and PPC with CB broadens novel application of both renewable polymers and CPCs. Copyright © 2008 Society of Chemical Industry     

Poly(lactic acid)/ethylene vinyl acetate copolymer blend composites with wood flour and wollastonite: Physical properties,morphology, and biodegradability

In the present study, poly(lactic acid) (PLA), a biodegradable plastic, was melt‐blended with five weight percentages (10–50 wt%) of ethylene vinyl acetate (EVA) copolymer, a non‐biodegradable plastic, having a vinyl acetate content of 19 wt% and a melt flow index of 530 g/10 min, on a twin screw extruder, followed by an injection molding. The blends at 10 and 20 wt% EVA revealed a noticeably increased impact strength and strain at break over the pure PLA, and the blend at 10 wt% EVA exhibited the highest impact strength and strain at break. The 90/10 (wt%/wt%) PLA/EVA blend was then selected for preparing either single or hybrid composite with wood flour (WF) and wollastonite (WT). The filler loading was fixed at 30 parts by weight per hundred of resin throughout the experiment, and the WF/WT weight ratios were 30/0, 20/10, 15/15, 10/20, and 0/30. The prepared composites were examined for their mechanical and thermal properties, melt flow index, flammability, water uptake, and biodegradability as a function of composition. All the composites showed a filler‐dose‐dependent decrease in the impact strength and strain at break, but an increase in the tensile and flexural modulus (optimal at 0/30 WF/WT) and tensile and flexural strength (optimal at 30/0 WF/WT) as compared with the neat 90/10 (wt%/wt%) PLA/EVA blend. In addition, the melt flow index, char residue, anti‐dripping ability, water uptake, and biodegradability of the composites were also higher than those of the neat blend. J. VINYL ADDIT. TECHNOL., 25:313–327, 2019. © 2019 Society of Plastics Engineers