Microstructure, spallation and corrosion of plasma sprayed Al2O3–13%TiO2 coatings

The electrochemical corrosion behaviours of the steel substrates coated with three different plasma sprayed Al₂O₃–13%TiO₂ coatings were studied in this paper. The three kinds of Al₂O₃–13%TiO₂ coatings were conventional ME coating, nanostructured NP coating and NS coating. There were micro cracks, laminar splats and straight columnar grains in ME coating. For the two nanostructured coatings, the laminar microstructure and columnar grains were not obvious. The NP coating had the highest hardness and spallation resistance. Electrochemical corrosion behaviour of the three coatings was mainly investigated by potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) in aqueous Na₂SO₄ solution.     

Toughening and strengthening mechanism of plasma sprayed nanostructured Al2O3–13 wt.%TiO2 coatings

The starting materials of Al₂O₃, TiO₂, ZrO₂ and CeO₂ nanoparticles were agglomerated into sprayable feedstock powders and plasma sprayed to form nanostructured coatings. There were net structures and fused structures in plasma sprayed nanostructured Al₂O₃–13 wt.%TiO₂ coatings. The net structures were derived from partially melted feedstock powders and the fused structures were derived from fully melted feedstock powders. The nanostructured Al₂O₃–13 wt.%TiO₂ coatings possessed higher hardness, bonding strength and crack growth resistance than conventional Metco 130 coatings which were mainly composed of lamellar fused structures. The higher toughness and strength of nanostructured Al₂O₃–13 wt.%TiO₂ coatings were mainly related to the obtained net structures.     

Deposition of Al2O3-TiO2 Nanostructured Powders by Atmospheric Plasma Spraying

Al₂O₃-13%TiO₂ coatings were deposited on stainless steel substrates from conventional and nanostructured powders using atmospheric plasma spraying (APS). A complete characterization of the feedstock confirmed its nanostructured nature. Coating microstructures and phase compositions were characterized using SEM, TEM, and XRD techniques. The microstructure comprised two clearly differentiated regions. One region, completely fused, consisted mainly of nanometer-sized grains of γ-Al₂O₃ with dissolved Ti⁺⁴. The other region, partly fused, retained the microstructure of the starting powder and was principally made up of submicrometer-sized grains of α-Al₂O₃, as confirmed by TEM. Coating microhardness as well as tribological behavior were determined. Vickers microhardness values of conventional coatings were in average slightly lower than the values for nanostructured coating. The wear resistance of conventional coatings was shown to be lower than that of nanostructured coatings as a consequence of Ti segregation. A correlation between the final properties, the coating microstructure, and the feedstock characteristics is given.     

Preparation and characterization of nanostructured Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-13wt.%TiO<Subscript>2</Subscript> ceramic coatings by plasma spraying

Nanostructured and conventional Al₂O₃-13wt.%TiO₂ ceramic coatings were prepared by plasma spraying with nanostructured agglomerated and conventional powders, respectively. The microstructure and microhardness of the coatings were investigated using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and microhardness measurement. Meanwhile, the friction and wear behaviors were analyzed and compared using a ball-on-disk tribometer. The results show that the conventional coating has lamellar stacking characteristic and has some pores. However, the nanostructured coating shows a bimodal microstructure, which is composed of both fully melted regions and partially melted regions. According to the microstructural difference, the partially melted regions can be divided into liquid-phase sintered regions (a three-dimensional net or skeleton-like structure: Al₂O₃-rich submicron particles embedded in the TiO₂-rich matrix) and solid-phase sintered regions (remained nanoparticles). The microstructural characteristics of the liquid-phase sintered region are formed due to the selective melting of TiO₂ nanoparticles during plasma spraying. On the other hand, the TiO₂ and Al₂O₃ nanoparticles of the solid-phase sintered regions are all unmelted during plasma spraying. Due to the existence of nanostructured microstructures, the nanostructured coating has a higher microhardness, a lower friction coefficient, and a better wear resistance than the conventional coating.     

HVOF-Sprayed Coatings Engineered from Mixtures of Nanostructured and Submicron Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-TiO<Subscript>2</Subscript> Powders: An Enhanced Wear Performance

In previous studies, it has been demonstrated that nanostructured Al₂O₃-13 wt.%TiO₂ coatings deposited via air plasma spray (APS) exhibit higher wear resistance when compared to that of conventional coatings. This study aimed to verify if high-velocity oxy-fuel (HVOF)-sprayed Al₂O₃-13 wt.%TiO₂ coatings produced using hybrid (nano + submicron) powders could improve even further the already recognized good wear properties of the APS nanostructured coatings. According to the abrasion test results (ASTM G 64), there was an improvement in wear performance by a factor of 8 for the HVOF-sprayed hybrid coating as compared to the best performing APS conventional coating. When comparing both hybrid and conventional HVOF-sprayed coatings, there was an improvement in wear performance by a factor of 4 when using the hybrid material. The results show a significant antiwear improvement provided by the hybrid material. Scanning electron microscopy (SEM) at low/high magnifications showed the distinctive microstructure of the HVOF-sprayed hybrid coating, which helps to explain its excellent wear performance. This article is an invited paper selected from presentations at the 2007 International Thermal Spray Conference and has been expanded from the original presentation. It is simultaneously published in Global Coating Solutions, Proceedings of the 2007 International Thermal Spray Conference, Beijing, China, May 14-16, 2007, Basil R. Marple, Margaret M. Hyland, Yuk-Chiu Lau, Chang-Jiu Li, Rogerio S. Lima, and Ghislain Montavon, Ed., ASM International, Materials Park, OH, 2007.     

Superior performance of high-velocity oxyfuel-sprayed nanostructured TiO<Subscript>2</Subscript> in comparison to air plasma-sprayed conventional Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-13TiO<Subscript>2</Subscript>

Air plasma-sprayed conventional alumina-titania (Al₂O₃-13wt.%TiO₂) coatings have been used for many years in the thermal spray industry for antiwear applications, mainly in the paper, printing, and textile industries. This work proposes an alternative to the traditional air plasma spraying of conventional aluminatitania by high-velocity oxyfuel (HVOF) spraying of nanostructured titania (TiO₂). The microstructure, porosity, hardness (HV 300 g), crack propagation resistance, abrasion behavior (ASTM G65), and wear scar characteristics of these two types of coatings were analyzed and compared. The HVOF-sprayed nanostructured titania coating is nearly pore-free and exhibits higher wear resistance when compared with the air plasma-sprayed conventional alumina-titania coating. The nanozones in the nanostructured coating act as crack arresters, enhancing its toughness. By comparing the wear scar of both coatings (via SEM, stereoscope microscopy, and roughness measurements), it is observed that the wear scar of the HVOF-sprayed nanostructured titania is very smooth, indicating plastic deformation characteristics, whereas the wear scar of the air plasma-sprayed alumina-titania coating is very rough and fractured. This is considered to be an indication of a superior machinability of the nanostructured coating.     

Corrosion resistance of Ni/Al2O3 coatings in NaCl solution

Abstract

This paper presents results of a research on the corrosion resistance of composite Ni/Al₂O₃ coatings electrochemically deposited from Watts baths containing different amounts (0, 20, 100 g dm^?3) of Al₂O₃ particles. Potentiodynamic tests and electrochemical impedance spectroscopy (EIS) measurements were carried out in a 3% solution of NaCl. The coatings with about 6 wt-% of corundum, deposited from a bath with 100 g dm^?3 of a powder, showed the best protective properties. The rate of corrosion of such coatings after 7 days of exposure in the NaCl solution was over two times slower than that of coatings containing 2 wt-% of Al₂O₃ and six times slower than that of a standard nickel coating. Two equivalent circuits: one consisting of two RC circuits and the other one made up of three RC circuits were used for the analysis of the impedance spectra. Regardless of the presence and amount of the Al₂O₃ particles in the nickel coating, during first day of exposure in the NaCl solution a layer of nickel oxides and hydroxides forms on the surface of the coatings increasing their corrosion resistance. In the case of coatings with 6 wt-% of Al₂O₃, the passive layer is least vulnerable to the aggressive action of Cl^? ions.     

Corrosion behavior of Zn?Ni?Al2O3 nanocomposite coatings obtained by electrodeposition from alkaline electrolytes

The aim of this work was to investigate the anti‐corrosive properties of nanocomposite Zn? Ni coatings containing Al₂O₃ nanoparticles, prepared from alkaline commercial electrolytes (pH 13), (PERFORMA 280.5, COVENTYA S.A.S, France), by electrodeposition on carbon steel (OL37). The corrosion resistance of the coatings prepared with different concentrations of Al₂O₃ (5, 10, and 15 g/L) was evaluated in 0.2 g/L Na₂SO₄ solution (pH 5) by open circuit potential (OCP) measurements, potentiodynamic polarization, and electrochemical impedance spectroscopy (EIS) techniques. The results of electrochemical measurements were corroborated with those obtained by using X‐ray diffraction analysis. The obtained results show that the introduction of Al₂O₃ nanoparticles in the plating bath generally brings an increase in corrosion resistance of Zn? Ni layers and put in evidence the existence of an optimal Al₂O₃ concentration. Under the examined conditions, the optimal concentration determined from polarization measurements was proven to be 5 g/L Al₂O₃. The highest value of the polarization resistance, R_p, obtained from impedance measurements corresponds also to Zn? Ni with 5 g/L Al₂O₃, which is in agreement with the results obtained from polarization and XRD measurements.     

Corrosion Resistance of APS- and HVOF-Sprayed Coatings in the Al2O3-TiO2 System

In this article, the results of corrosion investigations performed on thermally sprayed ceramic coatings with different compositions in the Al₂O₃-TiO₂ system (Al₂O₃, Al₂O₃-3%TiO₂, Al₂O₃-40%TiO₂, and TiO _x ) are presented. The coatings were deposited on corrosion-resistant steel substrates using atmospheric plasma spraying (APS) and high-velocity oxy-fuel (HVOF) spraying processes and characterized by means of optical microscopy, scanning electron microscopy (SEM), and x-ray diffraction (XRD). The corrosion properties were investigated in 1 N solutions of NaOH and H₂SO₄, at room temperature, 60 °C, and 85 °C, as well as in hydrothermal conditions with deionized water at 100 °C and 200 °C. The corrosion stability of the coatings depended on coating characteristics (spraying method, microstructure, and crystalline phase composition) and the corrosive environment (media, test temperature, and duration). In contrast to expectations, APS-sprayed coatings were found to be more corrosion-resistant than the HVOF-sprayed coatings. Addition of TiO₂ to Al₂O₃ increased the corrosion stability, especially for the HVOF-sprayed coatings. In this work, TiO _x coatings were found to be more corrosion-resistant than the Al₂O₃-based coatings.     

Corrosion behavior in boiling dilute HCI solution of different ceramic coatings fabricated by plasma spraying

An Al₂O₃ ceramic coating (A), a 13 wt.% TiO₂-Al₂O₃ (13TA) composite ceramic coating, and a Ni-Al-13wt.%TiO₂-Al₂O₃ (NA-13TA) gradient composite ceramic coating were prepared on Q235 steel by plasma spraying. The corrosion behavior of samples sprayed with these coatings in a boiling 5% HCl solution was investigated. It was shown that an A ceramic coating and a 13TA composite ceramic coating were destroyed after immersion for 17 and 23 h, respectively. The NA-13TA gradient composite ceramic coating was still sound after 14 days of immersion. The corrosion resistance of samples with the NA-13TA gradient composite ceramic coating was sharply improved due to the decreased amount of connected pores in the coating. The corrosion of the sample sprayed with the gradient ceramic coating included the partial corrosion of the surface ceramic coating and the interlayer coatings. The corrosion weight loss depended on the degree of open porosity.     

Impedance spectroscopy studies of electroless Ni–P matrix,Ni–W–P,Ni–P–ZrO2, and Ni–W–P–ZrO2 coatings exposed to 3.5% NaCl solution

Ni–P matrix, ternary Ni–W–P and Ni–P–ZrO₂ coatings, and quaternary Ni–W–P–ZrO₂ coatings were deposited using electroless method from a glycine bath. Their corrosion resistance was evaluated by electrochemical impedance spectroscopy (EIS) for various immersion times in a 3.5% NaCl solution. From among the investigated coatings, the ternary Ni–W–P coatings show the highest resistance to corrosion in the first hour of exposure to the 3.5% NaCl medium. An addition of ZrO₂ adversely affects the performance of both the Ni–P coatings and the Ni–W–P coatings. For all the coatings, including the ones containing tungsten, a marked decrease in pore resistance (R_por) over time is observed. This means that their corrosion resistance and capacity to protect the substrate decline. On the other hand, after 24 h immersion in the 3.5% NaCl solution the Ni–W–P coating shows the highest low‐frequency impedance modulus (|Z|_{f = 0.01 Hz}). As regards corrosion resistance, the Ni–P coatings and the Ni–W–P coatings perform best.     

Effect of sintering temperature on corrosion properties of sol–gel based Al2O3 coatings on pre-treated AZ91D magnesium alloy

A novel anti-corrosion sol–gel based Al₂O₃ coating was developed on the AZ91D magnesium alloy. The morphology, microstructure and composition of the coatings were investigated by scanning electron microscope coupled with energy dispersive spectroscopy, Fourier transform infrared spectrum analysis, X-ray diffraction, thermo-gravimetric and differential thermal analysis. The corrosion resistance of the coatings in 3.5 NaCl wt.% solution was studied using electrochemical measurements. The results demonstrated that a homogeneous Al₂O₃ coating could be obtained and the sol–gel coated samples sintered at 380 °C had the best corrosion resistance properties as compared to the specimens sintered at 120 and 280 °C.     

Ceria/stannate multilayer coatings on AZ91D Mg alloy

In this work, CeO₂/stannate multilayer coatings on AZ91D magnesium alloy were successfully obtained by chemical conversion and sol–gel dip coating. The stannate conversion coatings were prepared from a stannate aqueous bath containing Na₂SnO₃, CH₃COONa, Na₃PO₄ and NaOH at different temperatures and immersion times. Ceria films were produced on stannate/AZ91D starting from Ce(III) nitrate solutions in H₂O. In some cases, the PVA was added as chelating agent. Ceria top coatings were fired at 200 °C for 1 h. Coating microstructure was examined by FE-SEM. Finally, the corrosion resistance features of the coatings were tested by the electrochemical impedance spectroscopy (EIS) in 3 wt.% NaCl solution. The effect of PVA addition was evaluated in terms of microstructure and corrosion resistance features. CeO₂/stannate multilayer films, 3 μm thick, uniform, well adherent and nearly crack free were obtained. The formation of CeO₂ phase was confirmed by XRD and XPS analyses. The XPS depth profiles showed a limited diffusion of Mg towards the ceramic film. The EIS tests showed a significant improvement of corrosion resistance of the multilayer coatings (~ 16.6 kΩ after 48 h in NaCl solution) with respect to the blank alloy (~ 2.4 kΩ after 48 h in NaCl solution).     

Effects of critical plasma spray parameter and spray distance on wear resistance of Al2O3-8 wt.%TiO2 coatings plasma-sprayed with nanopowders

Effects of plasma spraying conditions on wear resistance of nanostructured Al₂O₃-8 wt.%TiO₂ coatings plasma-sprayed with nanopowders were investigated in this study. Five kinds of nanostructured coatings were plasma-sprayed on a low-carbon steel substrate by varying critical plasma spray parameter (CPSP) and spray distance. The coatings consisted of fully melted region of γ-Al₂O₃ and partially melted region, and the fraction of the partially melted regions and pores decreased with increasing CPSP or decreasing spray distance. The hardness and wear test results revealed that the hardness of the coatings increased with increasing CPSP or decreasing spray distance, and that the hardness increase generally led to the increase in wear resistance, although the hardness and wear resistance were not correlated in the coating fabricated with the low CPSP. The main wear mechanism was a delamination one in the coatings, but an abrasive wear mode also appeared in the coating fabricated with the low CPSP. According to these wear mechanisms, the improvement of wear resistance in the coating fabricated with the low CPSP could be explained because the improved resistance to fracture due to the presence of partially melted regions might compensate a deleterious effect of the hardness decrease.     

Electrophoretic deposition of 3YSZ coating on AZ91D using an aluminum interlayer

The zirconia stabilized by 3 mol % Y₂O₃ (3YSZ) was applied onto the surface of the magnesium alloy AZ91D using electrophoretic deposition (EPD) from a non- aqueous solvent. An interlayer of aluminum between the substrate and YSZ coating was also prepared by EPD. The preparation, microstructure and corrosion resistance of the coatings were investigated. The surface morphologies of the coatings were studied by scanning electron microscopy (SEM) and their compositions were determined by X-ray diffraction (XRD). The corrosion resistance of the coatings was evaluated by electrochemical impedance spectroscopy (EIS) in 3.5% NaCl solution. The results indicate that the aluminum interlayer has a favorable effect on the densification of the coating by formation of aluminum oxide. In addition, the corrosion resistance of coated AZ91D alloy in chloride solution is significantly improved because of the aluminum interlayer and an increase in charge-transfer resistance of the AZ91D surface in chloride solution was observed which was attributed to YSZ.     

Comparative study on corrosion protection properties of electroless Ni‐P‐ZrO2 and Ni‐P coatings on AZ91D magnesium alloy

Electroless Ni‐P‐ZrO₂ and Ni‐P coatings on AZ91D magnesium alloy were prepared, and their corrosion protection properties were compared in this paper. The potentiodynamic curves and electrochemical impedance spectroscopy (EIS) of the coated magnesium alloy in 3.5% NaCl solution showed that the corrosion performance of Ni‐P‐ZrO₂ composite coating was superior to that of Ni‐P coating. The same conclusion was obtained with salt spray and immersion tests. The corrosion morphologies of two kinds of coatings with various immersion time intervals in 3.5% NaCl solution indicated that most corrosion products concentrated on the nodules boundaries of Ni‐P coating and blocked corrosion pit was the main corrosion form. For the Ni‐P‐ZrO₂ coating, tortuous nodules boundaries were not the weak sites of the coating and corrosion initiated from the nickel phosphor alloy around the nanometer powders. Open corrosion pits occurred on the composite coating surface, and the coating was corroded gradually. Thus, the Ni‐P‐ZrO₂ coating exhibited better corrosion protection property to magnesium alloy substrate than Ni‐P coating.     

PREPARATION OF MICROARC OXIDATION COATING ON (Al2O3-SiO2)sf/AZ91D MAGNESIUM MATRIX COMPOSITE AND ITS ELECTROCHEMICAL IMPEDANCE SPECTROSCOPIC ANALYSIS\par

在硅酸盐电解液体系中, 采用交流微弧氧化方法在增强体体积分数为33%的 (Al₂O₃-SiO₂)_sf/AZ91D镁基复合材料表面制备出完整的保护性氧化膜. 利用SEM, EDS和XRD分析了氧化膜的形貌、成分和相组成, 测量了膜层的显微硬度分布. 采用电化学阻抗谱(EIS)评价了微弧氧化表面处理前后复合材料的电化学腐蚀性能, 确立了不同浸泡时间对应的等效电路. 结果表明, 微弧氧化膜主要由MgO和Mg₂SiO₄相组成, 最大硬度达到1017 HV. 氧化膜电化学阻抗模值|Z|与镁合金基体相比大幅度提高, 耐腐蚀性能明显高于基体. 在3.5%NaCl溶液里浸泡96 h后, EIS出现感抗弧, 显示膜内部开始出现点蚀破坏. 氧化膜耐蚀性由膜内致密层特性所决定.     

Cerium conversion coatings for AZ91D magnesium alloy in ethanol solution and its corrosion resistance

Golden-yellow-colored cerium conversion coatings on AZ91D magnesium alloy were obtained by immersion in ethanol solution and post-treated in 3.0 wt.% Na₃PO₄ aqueous solution. SEM revealed that the coatings deposited more heavily on α phase than on β phase. XPS results showed that the coatings consist of CeO₂, Ce₂O₃, CePO₄, Al₂O₃, Mg₃(PO₄)₂ and MgO. Corrosion tests indicated that the coatings with post-treatment significantly reduced the corrosion rate of AZ91D alloy in NaCl solution. The post-treatment is necessary for better corrosion resistance. The corrosion resistance of the coatings with post-treatment is superior to that of DOW No.1 coating.     

Ni/Cu定向结构涂层在不同浓度H2SO4中的耐蚀性能

为了研究Cu元素对Ni基合金定向结构涂层耐腐蚀性能的影响,向Ni60合金粉末中添加了5%Cu(质量分数,下同),制备了定向结构Ni60/Cu复合涂层。采用电化学试验和浸泡试验,评估了涂层在不同浓度H₂SO₄溶液中的电化学腐蚀特性和浸泡腐蚀性能,探讨了涂层在不同浓度H₂SO₄溶液中的腐蚀行为。结果表明,涂层在不同浓度H₂SO₄溶液中的腐蚀均表现为活化-钝化-过钝化的过程,电化学阻抗谱在整个时间常数内具有典型的容抗特征,H₂SO₄溶液浓度从5%增至80%时,电荷转移电阻先减小后增大,涂层的耐腐蚀性呈现先降低后升高的趋势。随着H₂SO₄溶液浓度的增加,涂层表面的腐蚀程度先加剧后逐渐减缓,且在H₂SO₄溶液浓度为40%时,腐蚀电位移至最负,腐蚀电流密度增至最大。但在H₂SO₄溶液浓度达到80...     

Effect of La2O3 on corrosion resistance of laser clad ferrite-based alloy coatings

The ferrite-based alloy powders with different contents of La₂O₃ were laser clad on a steel substrate. The microstructural features and phase structure of these coatings were studied by scanning electron microscope (SEM) and X-ray diffraction (XRD), respectively. The results showed that the microstructure of the coatings with La₂O₃ was refined and purified. The main phase of the coatings was γ (Fe, Ni). Moreover, the electrochemical properties of the coatings were investigated by anodic polarization curves and electrochemical impedance spectroscopy (EIS). Anodic polarization results indicated that both polarizing voltage and polarization current density were reduced with the addition of La₂O₃. EIS results showed that, with the increment of La₂O₃, the inductive arcs shrunk and capacitive arcs expanded. The inductive arc at low frequency was disappeared and changed to capacitive arc thoroughly when the content of La₂O₃ reached 1.2 wt.%. The corrosion weight loss experiment results showed that the corrosion rate was lower and the corrosion attack was lighter in the coatings with La₂O₃ than that without La₂O₃, resulting in a substantial improvement of the corrosion resistance.