Morphology and mechanical properties of ABS blends prepared from emulsion‐polymerized PB‐g‐SAN impact modifier with AIBN as initiator

A series of PB‐g‐SAN impact modifiers (polybutadiene particles grafted by styrene and acrylonitrile) are synthesized by seed emulsion copolymerization initiated by oil‐soluble initiator, azobisiobutyronitrile (AIBN). The ABS blends are obtained by mixing SAN resin with PB‐g‐SAN impact modifiers. The mechanical behavior and the phase morphology of ABS blends are investigated. The graft degree (GD) and grafting efficiency (GE) are investigated, and the high GD shows that AIBN has a fine initiating ability in emulsion grafting of PB‐g‐SAN impact modifiers. The morphology of the rubber particles is observed by the transmission electron microscopy (TEM). The TEM photograph shows that the PB‐g‐SAN impact modifier initiated by AIBN is more likely to form subinclusion inside the rubber particles. The dynamic mechanical analysis on ABS blends shows that the subinclusion inside the rubber phase strongly influences the T_g, maximum tan δ, and the storage modulus of the rubber phase. The mechanical test indicates that the ABS blends, which have the small and uniform subinclusions dispersed in the rubber particles, have the maximum impact strength. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Toughening of epoxy resin systems using low‐viscosity additives

This study has evaluated three low‐viscosity epoxy additives as potential tougheners for two epoxy resin systems. The systems used were a lower‐reactive resin based upon the diglycidyl ether of bisphenol A (DGEBA) and the amine hardener diethyltoluene diamine, while the second epoxy resin was based upon tetraglycidyl methylene dianiline (TGDDM) and a cycloaliphatic diamine hardener. The additives evaluated as potential tougheners were an epoxy‐terminated aliphatic polyester hyperbranched polymer, a carboxy‐terminated butadiene rubber and an aminopropyl‐terminated siloxane. This work has shown that epoxy‐terminated hyperbranched polyesters can be used effectively to toughen the lower cross‐linked epoxy resins, i.e. the DGEBA‐based systems, with the main advantage being that they have minimal effect upon processing parameters such as viscosity and the gel time, while improving the fracture properties by about 54 % at a level of 15 wt% of additive and little effect upon the T_g. This result was attributed to the phase‐separation process producing a multi‐phase particulate morphology able to initiate particle cavitation with little residual epoxy resin dissolved in the continuous epoxy matrix remaining after cure. The rubber additive was found to impart similar levels of toughness improvement but was achieved with a 10–20 °C decrease in the T_g and a 30 % increase in initial viscosity. The siloxane additive was found not to improve toughness at all for the DGEBA‐based resin system due to the poor dispersion within the epoxy matrix. The TGDDM‐based resin systems were found not to be toughened by any of the additives due to the lack of plastic deformation of the highly cross‐linked epoxy network Copyright © 2003 Society of Chemical Industry     

Effects of the polybutadiene/poly(styrene‐co‐acrylonitrile) ratio in a polybutadiene‐g‐poly(styrene‐co‐acrylonitrile) impact modifier on the morphology and mechanical behavior of acrylonitrile–butadiene–styrene blends

Polybutadiene‐g‐poly(styrene‐co‐acrylonitrile) (PB‐g‐SAN) impact modifiers with different polybutadiene (PB)/poly(styrene‐co‐acrylonitrile) (SAN) ratios ranging from 20.5/79.5 to 82.7/17.3 were synthesized by seeded emulsion polymerization. Acrylonitrile–butadiene–styrene (ABS) blends with a constant rubber concentration of 15 wt % were prepared by the blending of these PB‐g‐SAN copolymers and SAN resin. The influence of the PB/SAN ratio in the PB‐g‐SAN impact modifier on the mechanical behavior and phase morphology of ABS blends was investigated. The mechanical tests showed that the impact strength and yield strength of the ABS blends had their maximum values as the PB/SAN ratio in the PB‐g‐SAN copolymer increased. A dynamic mechanical analysis of the ABS blends showed that the glass‐transition temperature of the rubbery phase shifted to a lower temperature, the maximum loss peak height of the rubbery phase increased and then decreased, and the storage modulus of the ABS blends increased with an increase in the PB/SAN ratio in the PB‐g‐SAN impact modifier. The morphological results of the ABS blends showed that the dispersion of rubber particle in the matrix and its internal structure were influenced by the PB/SAN ratio in the PB‐g‐SAN impact modifiers. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 2165–2171, 2005     

Bis[4‐(4‐maleimidephen‐oxy)phenyl]propane/N,N‐4,4′‐bismaleimidodiphenylmethyene blend modified with diallyl bisphenol A

In this article, 2,2′‐bis[4‐(4‐maleimidephen‐oxy)phenyl)]propane (BMPP) resin and N,N‐4,4′‐bismaleimidodiphenylmethyene (BDM) resin blends were modified by diallyl bisphenol A (DABPA). The effects of the mole concentration of BMPP on mechanical properties, fracture toughness, and heat resistance of the modified resins were investigated. Scanning electron microscopy was used to study the microstructure of the fractured modified resins. The introduction of BMPP resin improves the fracture toughness and impact strength of the cured resins, whose thermal stabilities are hardly affected. Dynamic mechanical analysis shows that the modified resins can maintain good mechanical properties at 270.0°C, and their glass transition temperatures (T_g) are above 280.0°C. When the mole ratio of BDM : BMPP is 2 : 1(Code 3), the cured resin performs excellent thermal stability and mechanical property. Its T_g is 298°C, and the Charpy impact strength is 20.46 KJ/m². The plane strain critical stress intensity factor (K_IC) is 1.21 MPa·m^0.5 and the plane strain critical strain energy release rate (G_IC) is 295.64 J/m². Compared with that of BDM/DABPA system, the K_IC and G_IC values of Code 3 are improved by 34.07% and 68.10%, respectively, which show that the modified resin presented good fracture toughness. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40395.     

Role of core‐shell rubber particle cavitation resistance on toughenability of epoxy resins

The role of rubber particle cavitation resistance on toughening of epoxy resins is still unresolved. In this research, the role of rubber particle cavitation resistance was exclusively studied. Two types of core‐shell rubber (CSR) particles with different cavitation resistances were utilized for modifying epoxy resin. Matrix crosslink density (XLD) was varied by using nonstoichiometric amounts of hardener. Fracture toughness values of neat and CSR‐modified epoxy samples decreased with lowering of XLD via deviation from stoichiometric point. It was resulted by higher modulus and lower elongation at break of the nonstoichiometric samples, and also antiplasticization of epoxy networks resulted from suppression of β‐transition relaxation motions. In all XLDs, the CSR particles with higher core T_g and modulus yielded higher fracture energy. Results showed that core properties such as T_g and modulus of CSR particles had a significant effect on toughening of the epoxy networks. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Blends of epoxy resin with amine‐terminated polyoxypropylene elastomer: Morphology and properties

A liquid diglycidyl ether of bisphenol A (DGEBA) epoxy resin is blended in various proportions with amine‐terminated polyoxypropylene (POPTA) and cured using an aliphatic diamine hardener. The degree of crosslinking is varied by altering the ratio of diamine to epoxy molecules in the blend. The mixture undergoes almost complete phase separation during cure, forming spherical elastomer particles at POPTA concentrations up to 20 wt %, and a more co‐continuous morphology at 25 wt %. In particulate blends, the highest toughness is achieved with nonstoichiometric amine‐to‐epoxy ratios, which produce low degrees of crosslinking in the resin phase. In these blends, the correlation between G_IC and plateau modulus (above the resin T_g), over a wide range of amine‐to‐epoxy ratios, confirms the importance of resin ductility in determining the fracture resistance of rubber‐modified thermosets. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 427–434, 1999     

Boiling water aging of polycarbonate and polycarbonate/acrylonitrile–butadiene–styrene resin and polycarbonate/low‐density polyester blends

The effects of boiling water on the mechanical and thermal properties and morphologies of polycarbonate (PC), PC/acrylonitrile–butadiene–styrene resin (PC/ABS), and PC/low‐density polyester (PC/LDPE) blends (compositions of PC/ABS and PC/LDPE blends were 80/20) were studied. PC and the PC/ABS blend had a transition from ductile to brittle materials after boiling water aging. The PC/LDPE blend was more resistant to boiling water aging than PC and the PC/ABS blend. The thermal properties of glass‐transition temperature (T_g) and melting temperature (T_m) in PC and the blends were measured by DSC. The T_g of PC and PC in the PC/ABS and PC/LDPE blends decreased after aging. The T_g of the ABS component in the PC/ABS blend did not change after aging. The supersaturated water in PC clustered around impurities or air bubbles leading to the formation of microcracks, which was the primary reason for the ductile–brittle transition in PC, and the microcracks could not recover after PC was treated at 160°C for 6 h. The PC/ABS blend showed slightly higher resistance to boiling water than did PC. The highest resistance to boiling water of the PC/LDPE blend may be attributed to its special structural morphology. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 589–595, 2003     

Fabrication of polypropylene blends with excellent low‐temperature toughness and balanced toughness‐rigidity by a combination of EPR and SEEPS

To overcome serious rigidity depression of rubber‐toughened plastics and fabricate a rigidity‐toughness balanced thermoplastic, a combination of styrene‐[ethylene‐(ethylene‐propylene)]‐styrene block copolymer (SEEPS) and ethylene‐propylene rubber (EPR) was used to toughen polypropylene. The dynamic mechanical properties, crystallization and melting behavior, and mechanical properties of polypropylene (PP)/EPR/SEEPS blends were studied in detail. The results show that the combination of SEEPS and EPR can achieve the tremendous improvement of low‐temperature toughness without significant strength and rigidity loss. Dynamic mechanical properties and phase morphology results demonstrate that there is a good interfacial strength and increased loss of compound rubber phase comprised of EPR component and EP domain of SEEPS. Compared with PP/EPR binary blends, although neither glass transition temperature (T_g) of the rubber phase nor T_g of PP matrix in PP/EPR/SEEPS blends decreases, the brittle‐tough transition temperature (T_bd) of PP/EPR/SEEPS blends decreases, indicating that the increased interfacial interaction between PP matrix and compound rubber phase is also an effective approach to decrease T_bd of the blends so as to improve low‐temperature toughness. The balance between rigidity and toughness of PP/EPR/SEEPS blends is ascribed to the synergistic effect of EPR and SEEPS on toughening PP. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45714.     

Preparation and properties of TiO2‐filled poly(acrylonitrile‐butadiene‐styrene)/epoxy hybrid composites

Poly (acrylonitrile‐butadiene‐styrene) (ABS) was used to modify diglycidyl ether of bisphenol‐A type of epoxy resin, and the modified epoxy resin was used as the matrix for making TiO₂ reinforced nanocomposites and were cured with diaminodiphenyl sulfone for superior mechanical and thermal properties. The hybrid nanocomposites were characterized by using thermogravimetric analyzer (TGA), dynamic mechanical analyzer (DMA), universal testing machine (UTM), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The bulk morphology was carefully analyzed by SEM and TEM and was supported by other techniques. DMA studies revealed that the DDS‐cured epoxy/ABS/TiO₂ hybrid composites systems have two T_gs corresponding to epoxy and ABS rich phases and have better load bearing capacity with the addition of TiO₂ particles. The addition of TiO₂ induces a significant increase in tensile properties, impact strength, and fracture toughness with respect to neat blend matrix. Tensile toughness reveals a twofold increase with the addition of 0.7 wt % TiO₂ filler in the blend matrix with respect to neat blend. SEM micrographs of fractured surfaces establish a synergetic effect of both ABS and TiO₂ components in the epoxy matrix. The phenomenon such us cavitation, crack path deflection, crack pinning, ductile tearing of the thermoplastic, and local plastic deformation of the matrix with some minor agglomerates of TiO₂ are observed. However, between these agglomerates, the particles are separated well and are distributed homogeneously within the polymer matrix. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Effects of amino‐functionalized carbon nanotubes on the properties of amine‐terminated butadiene–acrylonitrile rubber‐toughened epoxy resins

Amino‐functionalized multiwalled carbon nanotubes (MWCNT‐NH₂s) as nanofillers were incorporated into diglycidyl ether of bisphenol A (DGEBA) toughened with amine‐terminated butadiene–acrylonitrile (ATBN). The curing kinetics, glass‐transition temperature (T_g), thermal stability, mechanical properties, and morphology of DGEBA/ATBN/MWCNT‐NH₂ nanocomposites were investigated by differential scanning calorimetry (DSC), thermogravimetric analysis, a universal test machine, and scanning electron microscopy. DSC dynamic kinetic studies showed that the addition of MWCNT‐NH₂s accelerated the curing reaction of the ATBN‐toughened epoxy resin. DSC results revealed that the T_g of the rubber‐toughened epoxy nanocomposites decreased nearly 10°C with 2 wt % MWCNT‐NH₂s. The thermogravimetric results show that the addition of MWCNT‐NH₂s enhanced the thermal stability of the ATBN‐toughened epoxy resin. The tensile strength, flexural strength, and flexural modulus of the DGEBA/ATBN/MWCNT‐NH₂ nanocomposites increased increasing MWCNT‐NH₂ contents, whereas the addition of the MWCNT‐NH₂s slightly decreased the elongation at break of the rubber‐toughened epoxy. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40472.     

Comparison of thermoset soy protein resin toughening by natural rubber and epoxidized natural rubber

Fully bio‐based soy protein isolate (SPI) resins were toughened using natural rubber (NR) and epoxidized natural rubber (ENR). Resin compositions containing up to 30 wt % NR or ENR were prepared and characterized for their physical, chemical and mechanical properties. Crosslinking between SPI and ENR was confirmed using ¹H‐NMR and ATR‐FTIR. All SPI/NR resins exhibited two distinctive drops in their modulus at glass transition temperature (T_g ) and degradation temperature (T_d ) at around ?50 and 215 °C, corresponding to major segmental motions of NR and SPI, respectively. SPI/ENR resins showed similar T_g and T_d transitions at slightly higher temperatures. For SPI/ENR specimens the increase in ENR content from 0 to 30 wt % showed major increase in T_g from ?23 to 13 °C as a result of crosslinking between SPI and ENR. The increase in ENR content from 0 to 30 wt % increased the fracture toughness from 0.13 to 1.02 MPa with minimum loss of tensile properties. The results indicated that ENR was not only more effective in toughening SPI than NR but the tensile properties of SPI/ENR were also significantly higher than the corresponding compositions of SPI/NR. SPI/ENR green resin with higher toughness could be used as fully biodegradable thermoset resin in many applications including green composites. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44665.     

Blends of poly(vinyl chloride) with α‐methylstyrene‐acrylonitrile‐butadiene‐styrene copolymer: Thermal properties,mechanical properties,and morphology

Binary blends of poly(vinyl chloride) (PVC) with α‐methylstyrene‐acrylonitrile‐butadiene‐styrene copolymer (AMS‐ABS) were prepared via melt blending. A single glass transition temperature (T_g) was observed by differential scanning calorimetry, thus indicating that PVC is miscible with the α‐methylstyrene‐acrylonitrile‐styrene in AMS‐ABS. The results from attenuated total reflection Fourier transform infrared spectra indicated that specific strong interactions were not available in the blends. With increasing amounts of AMS‐ABS, both heat distortion temperature and thermal stability were increased considerably. With regard to mechanical properties, flexural and tensile properties decreased with increasing AMS‐ABS content. A synergism was observed in impact strength. The morphology of both impact‐fractured and tensile‐fractured surfaces, observed by scanning electron microscopy, correlated well with the mechanical properties. It is suggested that there was a transition of fracture mechanisms with the changing composition of the binary blends—from shear yielding for blends rich in PVC to cavitation for blends rich in AMS‐ABS. J. VINYL ADDIT. TECHNOL., 19:1–10, 2013. © 2013 Society of Plastics Engineers     

Influence of epoxy resin on the properties of maleic anhydride functionalized acrylonitrile–butadiene–styrene copolymer toughened polyamide 6 blends

Maleic anhydride functionalized acrylonitrile–butadiene–styrene copolymer (ABS‐g‐MA) was used as an impact modifier of polyamide 6 (PA6). Epoxy resin was introduced into PA6/ABS‐g‐MA blends to further improve their properties. Notched Izod impact tests showed that the impact strength of PA6/ABS‐g‐MA could be improved from 253 to 800 J/m with the addition of epoxy resin when the ABS‐g‐MA content was set at 25 wt %. Differential scanning calorimetry results showed that the addition of epoxy resin made the crystallization temperature and melting temperature shift to lower temperatures; this indicated the decrease in the PA6 crystallization ability. Dynamic mechanical analysis testing showed that the addition of epoxy resin induced the glass‐transition temperature of PA6 and the styrene‐co‐acrylonitrile copolymer phase to shift to higher temperatures due to the chemical reactions between PA6, ABS‐g‐MA, and epoxy resin. The scanning electron microscopy results indicated that the ABS‐g‐MA copolymer dispersed into the PA6 matrix uniformly and that the phase morphology of the PA6/ABS‐g‐MA blends did not change with the addition of the epoxy resin. Transmission electron microscopy showed that the epoxy resin did not change the deformation mechanisms of the PA6/ABS‐g‐MA blends. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Influence of accelerated ageing on methacrylate‐based denture resins heterogeneity as viewed by ESR‐spin‐probe method

The electron‐spin‐resonance (ESR) spin‐probe method, was used to study the heterogeneity of denture resins based on poly(methyl methacrylate). Results for three resins processed by microwave energy, conventional curing and cold curing (depending on the curing procedure and exposed to ageing in various environmental conditions) were compared. All three cured resins were stored over the same time (1200 h) in distilled water at ambient temperature and in artificial saliva at 348 K. The temperature‐dependent ESR spectra of a spin probe dispersed in the denture resins are analyzed in terms of line‐shapes and line‐widths. The appearance of two spectral components was taken as an indication of resin heterogeneity. The results reveal that the cold‐cured resin has a lower local density in comparison with microwave and conventionally cured resin. The amount of residual monomer also contributes to the local motion of polymer segments. The change of denture resins exposed to ageing is influenced both by the structure of the original resin and the ageing conditions. Restricted motion of a spin probe incorporated into the acrylic resins exposed to accelerated ageing suggests additional crosslinking of polymer chains. The differences are observed for all the investigated resins, but the highest change is observed with the cold‐cured resin. The ESR results are accompanied by T_g and T_m measurements. Copyright © 2005 Society of Chemical Industry     

Fatty acid‐based comonomers as styrene replacements in soybean and castor oil‐based thermosetting polymers

In this study, a fatty acid‐based comonomer is employed as a styrene replacement for the production of triglyceride‐based thermosetting resins. Styrene is a hazardous pollutant and a volatile organic compound. Given their low volatility, fatty acid monomers, such as methacrylated lauric acid (MLA), are attractive alternatives in reducing or eliminating styrene usage. Different triglyceride‐derived cross‐linkers resins were produced for this purpose: acrylated epoxidized soybean oil (AESO), maleinated AESO (MAESO), maleinated soybean oil monoglyceride (SOMG/MA) and maleinated castor oil monoglyceride (COMG/MA). The mechanical properties of the bio‐based polymers and the viscosities of bio‐based resins were analyzed. The viscosities of the resins using MLA were higher than that of resins with styrene. Decreasing the content of MLA increased the glass transition temperature (T_g). In fact, the T_g of bio‐based resin/MLA polymers were on the order of 60°C, which was significantly lower than the bio‐based resin/styrene polymers. Ternary blends of SOMG/MA and COMG/MA with MLA and styrene improved the mechanical properties and reduced the resin viscosity to acceptable values. Lastly, butyrated kraft lignin was incorporated into the bio‐based resins, ultimately leading to improved mechanical properties of this thermoset but with unacceptable increases in viscosity. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Toughening of vinylester–urethane hybrid resins through functionalized polymers

Liquid nitrile rubber, hyperbranched polyester, and core/shell rubber particles of various functionality, namely, vinyl, carboxyl, and epoxy, were added up to 20 wt % to a bisphenol‐A‐based vinylester–urethane hybrid (VEUH) resin to improve its toughness. The toughness was characterized by the fracture toughness (K_c) and energy (G_c) determined on compact tensile (CT) specimens at ambient temperature. Toughness improvement in VEUH was mostly achieved when the modifiers reacted with the secondary hydroxyl groups of the bismethacryloxy vinyl ester resin and with the isocyanate of the polyisocyanate compound, instead of participating in the free‐radical crosslinking via styrene copolymerization. Thus, incorporation of carboxyl‐terminated liquid nitrile rubber (CTBN) yielded the highest toughness upgrade with at least a 20 wt % modifier content. It was, however, accompanied by a reduction in both the stiffness and glass transition temperature (T_g) of the VEUH resin. Albeit functionalized (epoxy and vinyl, respectively) hyperbranched polymers were less efficient toughness modifiers than was CTBN, they showed no adverse effect on the stiffness and T_g. Use of core/shell modifiers did not result in toughness improvement. The above changes in the toughness response were traced to the morphology assessed by dynamic mechanical thermal analysis (DMTA) and fractographic inspection of the fracture surface of broken CT specimens. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 672–680, 2002; DOI 10.1002/app.10392     

Mechanical,thermal, and water uptake characteristics of woodflour‐filled polyvinyl chloride/acrylonitrile butadiene styrene blends

Woodflour‐filled composites based on polymeric blends of polyvinyl chloride (PVC) and super high‐impact grade ABS were developed. Mechanical, thermal, and water uptake characteristics of the PVC/ABS matrix and their wood composites were evaluated. In the case of PVC/ABS matrix, the blend at a mass ratio of 50/50 rendered the impact strength with a very high value of up to 65 kJ/m², noticeably higher than those of the parent resins, that is, 6 kJ/m² of PVC and 35 kJ/m² of ABS. Dynamic mechanical analysis thermograms showed two distinct glass transition temperatures (T_gs) that shifted toward each other indicating partial miscibility of the blends. Water absorption of the blends after 24 h immersion was low, that is, within the range of 0.04–0.2 wt % and exhibits a behavior closed to pseudo‐Fickian type. The obtained PVC/ABS wood composites exhibited an increase of flexural modulus as well as T_gs with an increase of woodflour content. Finally, impact strength of the PVC/ABS composites was significantly higher than those of PVC composites or polyethylene composites comparing at the same woodflour content. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Toughening of cyanate ester resin by N‐phenylmaleimide–N‐(p‐hydroxy)phenyl‐maleimide–styrene terpolymers and their hybrid modifiers

N‐Phenylmaleimide–N‐(p‐hydroxy)phenylmaleimide–styrene terpolymer (HPMS), carrying reactive p‐hydroxyphenyl groups, was prepared and used to improve the toughness of cyanate ester resins. Hybrid modifiers composed of N‐phenylmaleimide–styrene copolymer (PMS) and HPMS were also examined for further improvement in toughness. Balanced properties of the modified resins were obtained by using the hybrid modifiers. The morphology of the modified resins depends on HPMS structure, molecular weight and content, and hybrid modifier compositions. The most effective modification of the cyanate ester resin was attained because of the co‐continuous phase structure of the modified resin. Inclusion of the modifier composed of 10 wt% PMS (M_w 136 000 g mol^?1) and 2.5 wt% HPMS (hydroxyphenyl unit 3 mol%, M_w 15 500 g mol^?1) led to 135% increase in the fracture toughness (K_IC) for the modified resin with a slight loss of flexural strength and retention of flexural modulus and glass transition temperature, compared with the values for the unmodified resin. Furthermore, the effect of the curing conditions on the mechanical and thermal properties of the modified resins was examined. The toughening mechanism is discussed in terms of the morphological and dynamic viscoelastic behaviour of the modified cyanate ester resin system. © 2001 Society of Chemical Industry     

Structure,thermal, and mechanical properties of DDM‐hardened epoxy/benzoxazine hybrids: Effects of epoxy resin functionality and ETBN toughening

Bifunctional, trifunctional, and tetrafunctional epoxy (EP) resins were hardened with stoichiometric amount of 4,4′‐diaminodiphenyl methane in presence and absence of benzoxazine (BOX). The EP/BOX ratio of the hybrid systems was constant, viz. 50/50 wt %. For the bifunctional EP, the EP/BOX range covered the ratios 75/25 and 25/75 wt %, as well. Epoxy‐terminated liquid nitrile rubber (ETBN) was incorporated in 10 wt % in the systems with trifunctional and tetrafunctional EP, and in 10, 15, and 20 wt % in the EP/BOX with bifunctional EP to improve their toughness. Information on the structure and morphology of the hybrid systems was received from differential scanning calorimetric, dynamic‐mechanical thermal analysis, atomic force microscopic, and scanning electron microscopic studies. The flexural, fracture mechanical properties, thermal degradation, and fire resistance of the EP/BOX and EP/BOX/ETBN hybrids were determined. It was found that some homopolymerized BOX was built in the EP/BOX conetwork in form of nanoscale inclusions, whereas ETBN formed micron scaled droplets of sea‐island structure. Incorporation of BOX improved the charring and fire resistance, enhanced the flexural modulus and strength, reduced the glass transition (T_g), the fracture toughness, and energy. Additional modification with ETBN decreased the charring, fire resistance, flexural modulus and strength, as well as T_g, however, improved the fracture toughness and especially the fracture energy. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Time–temperature–transformation cure diagrams of phenol–formaldehyde and lignin–phenol–formaldehyde novolac resins

In this study, the time–temperature– transformation (TTT) cure diagrams of the curing processes of several novolac resins were determined. Each diagram corresponded to a mixture of commercial phenol–formaldehyde novolac, lignin–phenol–formaldehyde novolac, and methylolated lignin–phenol–formaldehyde novolac resins with hexamethylenetetramine as a curing agent. Thermomechanical analysis and differential scanning calorimetry techniques were applied to study the resin gelation and the kinetics of the curing process to obtain the isoconversional curves. The temperature at which the material gelled and vitrified [the glass‐transition temperature at the gel point (_gelT_g)], the glass‐transition temperature of the uncured material (without crosslinking; T_g0), and the glass‐transition temperature with full crosslinking were also obtained. On the basis of the measured of conversion degree at gelation, the approximate glass‐transition temperature/conversion relationship, and the thermokinetic results of the curing process of the resins, TTT cure diagrams of the novolac samples were constructed. The TTT diagrams showed that the lignin–novolac and methylolated lignin–novolac resins presented lower T_g0 and _gelT_g values than the commercial resin. The TTT diagram is a suitable tool for understanding novolac resin behavior during the isothermal curing process. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011