Non‐isolated single‐switch DC–DC converters with extended duty cycle for high step‐down voltage applications

Several new topologies of single‐switch non‐isolated DC–DC converters with wide conversion gain and reduced semiconductor voltage stress are proposed in this paper. Most of the proposed topologies are derived from the conventional inverse of SEPIC (Zeta) converter. The proposed topologies can operate with larger switch duty cycles compared with the existing single switch topologies, hence, making them well suitable for high step‐down voltage conversion applications. With extended duty cycle, the current stress in the active power switch is reduced, leading to a significant improvement of the system losses. Moreover, the active power switch in some of the proposed topologies is utilized much better compared to the conventional Zeta and quadratic‐buck converters. The principle of operation, theoretical analysis, and comparison of circuit performances with other step‐down converters are discussed regarding voltage and current stress and switch silicon utilization. Finally, simulation and experimental results for a design example of a 50 W/5 V at 42‐V input voltage operating at 50 kHz will be provided to evaluate the performance of the proposed converters. Copyright © 2014 John Wiley & Sons, Ltd.     

Graph‐theoretical approach to 2‐switch DC–DC converters

This paper presents a graph‐theoretic approach to analyse and synthesize switch mode DC–DC converters. The result is based on the state‐space averaging equation and the fundamental graph theory. Hence our proposed method is applied to various kinds of DC–DC converters with two switches and topological conditions for two‐switch DC–DC converters are obtained systematically. Copyright © 2005 John Wiley & Sons, Ltd.     

Fast‐transient DC‐DC converter using a high‐performance error amplifier with a rapid output‐voltage control technique

This letter presents a method for improving the transient response of DC‐DC converters. The proposed technique replaces the conventional error amplifier with a combination of two different amplifiers to achieve a high loop gain and high slew rate. In addition, a rapid output‐voltage control circuit is employed to further reduce the recovery time. The proposed technique was applied to a four‐phase buck converter, and the chip was implemented using a 0.18‐μm CMOS process. The switching frequency of each phase was set at 2 MHz. Using a supply voltage of 2.7–5.5 V and an output voltage of 0.6–1.5 V, the regulator provided up to 2‐A load current with maximum measured recovery time of only 6.2 and 6.5 μs for increasing and decreasing load current, respectively. Copyright © 2017 John Wiley & Sons, Ltd.     

MTL‐based implementation of current‐mode CMOS RMS‐to‐DC converters

In this paper, systematic implementation of current‐mode RMS‐to‐DC converters based upon MOS translinear (MTL) principle, utilizing symmetric cascoded MTL cell (SCMC) is proposed. Theory of operation and mathematical analysis of both explicit (direct) and implicit (indirect) techniques for realization of SCMC‐based RMS‐to‐DC converters are discussed. The SCMC includes a folded MTL loop and realizes an MTL equation. MTL principle utilizes the square law characteristics of saturated MOS transistors to realize square‐root domain (SRD) functions. The SCMC is constructed by two connected cascoded current mirrors and has a compact, symmetric, and multi‐purpose structure, with capability of implementing the circuits into the programmable and configurable structures. The proposed RMS‐to‐DC converters utilize the SCMC along with a configurable current mirror array. The required squaring and square‐rooting functions are realized using the SCMC, after proper configuration of the current mirror array. The proposed circuits have been implemented using a reconfigurable architecture fabricated in a 0.5 µm CMOS technology. Copyright © 2014 John Wiley & Sons, Ltd.     

Formulation of buffer energy and experimental results of energy factor of DC–DC converters

Two concepts of buffer energy and energy factor for switched‐mode power converters are proposed and examined. They can describe the nonactive power as well as predict and evaluate the performance of DC–DC converters. The concepts can also find usage in both DC and AC systems. The energy factors of six basic topologies of DC–DC converter have been studied, and they can be used to compare the performance of different topologies. It can be shown that both buffer energy and energy factor provide an alternative understanding of the energy processes in DC–DC converters. Experimental results demonstrate that energy factors and buffer energy can be measured. The measured results for some basic converters are consistent with the theoretical values. Buffer energy, energy factor, and their related concepts proposed in this article have promising application in the design of DC–DC converters. Copyright © 2011 John Wiley & Sons, Ltd.     

Pulse current regenerative resonant snubber‐assisted two‐switch flyback‐type ZVS PWM DC‐DC converter

In this paper, a two‐switch high‐frequency flyback transformer‐type zero voltage soft‐switching PWM DC‐DC converter using IGBTs is proposed. Effective applications for this power converter can be found in auxiliary power supplies of rolling stock transportation and electric vehicles. This power converter is basically composed of two active power switches and a flyback high‐frequency transformer. In addition to these, two passive lossless snubbers with power regeneration loops for energy recovery, consisting of a three‐winding auxiliary high‐frequency transformer, auxiliary capacitors and diodes are introduced to achieve zero voltage soft switching from light to full load conditions. Furthermore, this power converter has some advantages such as low cost circuit configuration, simple control scheme, and high efficiency. Its operating principle is described and to determine circuit parameters, some practical design considerations are discussed. The effectiveness of the proposed power converter is evaluated and compared with the hard switching PWM DC‐DC converter from an experimental point of view, and the comparative electromagnetic conduction and radiation noise characteristics of both DC‐DC power converter circuits are also depicted. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 152(3): 74–81, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20081     

An Approach to a Higher‐Power‐Density Power Supply for a 380‐V DC Distribution System

A methodology for realizing a higher‐power‐density DC‐DC converter has been proposed for a power unit installed in a 380‐V DC distribution system. The possibility of the converter design will be strengthened by using the series–parallel connection topology for isolated DC‐DC converters. A converter prototype with a power density of 10 W/cm³ has been fabricated, and the feasibility of the converter design has been confirmed experimentally. This result contributes to the realization of a highly efficient and highly space‐saving 380‐V DC distribution system. © 2013 Wiley Periodicals, Inc. Electr Eng Jpn, 186(3): 51–62, 2014; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.22494     

A DC‐side damping control method for power converters to suppress resonance in DC power network

This paper describes a damping control method of power converters for suppression of resonance in DC power network. The resonance occurs when a resonant frequency of the DC distribution line coincides with the frequency of the harmonic or interharmonic components generated by the power converters. For detailed investigation, a combined system which consists of a pulse‐width modulated (PWM) rectifier and a PWM inverter is treated as the simplest example. To suppress the resonance, a DC‐side damping control method is proposed and its implementation and design method are discussed in detail. Then, the proposed damping control method is applied to the combined system of a PWM rectifier and a PWM inverter. Experimental results verify the validity and practicability of the proposed damping control method. © 2012 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

A ZVS‐ZCS phase shift full bridge DC‐DC converter with secondary‐side control for battery charging applications

The output power requirement of battery charging circuits can vary in a wide range, hence making the use of conventional phase shift full bridge DC‐DC converters infeasible because of poor light load efficiency. In this paper, a new ZVS‐ZCS phase shift full bridge topology with secondary‐side active control has been presented for battery charging applications. The proposed circuit uses 2 extra switches in series with the secondary‐side rectifier diodes, operating with phase shift PWM. With the assistance of transformer's magnetizing inductance, the proposed converter maintains zero voltage switching (ZVS) of the primary‐side switches over the entire load range. The secondary‐side switches regulate the output voltage/current and perform zero current switching (ZCS) independent of the amount of load current. The proposed converter exhibits a significantly better light load efficiency as compared with the conventional phase shift full bridge DC‐DC converter. The performance of the proposed converter has been analyzed on a 1‐kW hardware prototype, and experimental results have been included.     

高频谐波扰动下直流电网阻抗模型特征分析

直流配电网故障发展迅速且无固定频率的故障特征分量,因此,其故障特征的准确解析有重要的研究意义。从直流故障状态下系统阻抗特性分析出发,重点研究各类直流换流器的频率-阻抗响应。基于DC/DC变换器和模块化多电平换流器谐波通路,根据元件参数特性进行合理等效与简化,建立了上述变换器的高频阻抗模型。所述模型不受换流器控制策略影响,能够精确反映各类换流器的高频阻抗特性。     

Dynamic modeling of DC–DC converters with peak current control in double‐stage photovoltaic grid‐connected inverters

In photovoltaic (PV) double‐stage grid‐connected inverters a high‐frequency DC–DC isolation and voltage step‐up stage is commonly used between the panel and the grid‐connected inverter. This paper is focused on the modeling and control design of DC–DC converters with Peak Current mode Control (PCC) and an external control loop of the PV panel voltage, which works following a voltage reference provided by a maximum power point tracking (MPPT) algorithm. In the proposed overall control structure the output voltage of the DC–DC converter is regulated by the grid‐connected inverter. Therefore, the inverter may be considered as a constant voltage load for the development of the small‐signal model of the DC–DC converter, whereas the PV panel is considered as a negative resistance. The sensitivity of the control loops to variations of the power extracted from the PV panel and of its voltage is studied. The theoretical analysis is corroborated by frequency response measurements on a 230 W experimental inverter working from a single PV panel. The inverter is based on a Flyback DC–DC converter operating in discontinuous conduction mode (DCM) followed by a PWM full‐bridge single‐phase inverter. The time response of the whole system (DC–DC + inverter) is also shown to validate the concept. Copyright © 2011 John Wiley & Sons, Ltd.     

Analytical multi‐parametric stability boundaries of DC‐DC buck converters under V1 control concept

Two main methods for controlling switching converters exist in the literature. The direct one is the voltage mode control, which suffers from some disadvantages such as slow response to load variations and an input voltage‐dependent total loop gain. The current mode control can overcome these problems but at the expense of extra cost and more complex control design. V¹ concept is a new promising control technique for designing voltage mode control of buck‐type converters with an optimal response similar to current mode control. In this paper, the dynamics and the stability of buck converters under V¹ control are studied. In particular, subharmonic oscillation limits in the parameter space are addressed. First, a closed‐loop state‐space model is derived and then used to formulate an analytical matrix‐form expression for predicting the stability limit of the system. Using this expression, multi‐parametric stability boundaries are obtained. It is shown that the equivalent series inductance of the output capacitor can narrow the stability region. It is also demonstrated that the integral action in the feedback loop of a V¹‐controlled buck converter has a negligible effect on the subharmonic oscillation boundary. The theoretical analysis is validated through numerical simulation of the circuit‐level switched model of the system. Copyright © 2017 John Wiley & Sons, Ltd.     

含多类型故障限流设备动作的直流电网保护时序配合

柔性直流电网作为新能源并网的有效手段,要求能够可靠开断直流故障电流。直流电网中配置的多种类型故障限流设备间的故障保护时序配合亟须研究。文中基于直流电网直流线路双极短路故障,研究了故障限流器、直流断路器、半桥全桥混合型模块化多电平换流器以及DC/DC变换器这几类多类型故障限流设备的故障保护时序配合。针对包含环网状以及辐射状结构的复合型多端直流电网系统中的不同区域,配置不同类型的故障限流设备,同时采用检测故障电流变化率的方法判断直流断路器是否可靠动作。根据不同的故障区域,提出了相应的故障限流设备间的保护时序配合方案,并且考虑了部分限流设备如直流断路器拒动后其他限流设备的动作逻辑。在PSCAD/EMTDC仿真中验证了提出的直流电网中多类型限流设备保护时序的可靠性和有效性。     

Dynamic modeling of a dual active bridge DC to DC converter with average current control and load‐current feed‐forward

Bidirectional power flow is needed in many power conversion systems like energy storage systems, regeneration systems, power converters for improvement of the power quality and some DC‐DC applications where bidirectional high power conversion and galvanic isolation are required. The dual active bridge (DAB) is an isolated, high voltage ratio DC‐DC converter suitable for high power density and high power applications, being a key interface between renewable energy sources and energy storage devices. This paper is focused on the modeling and control design of a DC‐DC system with battery storage based on a DAB converter with average current mode control of the output current and output voltage control. The dynamic response of the output voltage to load steps is improved by means of an additional load‐current feed‐forward control loop. An analytical study of the load‐current feed‐forward is presented and validated by means of both simulations and experimental results. Copyright © 2014 John Wiley & Sons, Ltd.     

Steady‐state stability of shaft torsional oscillation in an ac‐dc interconnected system with self‐commutated converters

Recent progress in power electronics technology makes it possible to consider applying self‐commutated converters using gate turn‐off thyristors (GTOs) to HVDC transmission systems. Since the self‐commutated converter can be operated stably without depending on ac‐side voltage, the magnitude and the phase angle of the converter output voltage can be controlled independently. Therefore, this type of converter will improve voltage stability at its ac side. On the other hand, shaft torsional oscillation of a thermal power plant caused by the interaction between the shaft‐generator system and the control system of the self‐commutated converter is still an open problem. In this paper, a linearized model for eigenvalue analysis of a power system, including HVDC interconnection with self‐commutated converters, is described to analyze the effect of the self‐commutated converter on the shaft torsional oscillation of a thermal power plant. Then, numerical results from the eigenvalue analysis of the shaft torsional oscillation are presented. Results obtained by the frequency response method are also reported. The numerical results make it clear that parameter regions of DC‐AVR and ACR control systems of self‐commutated converters exist where the shaft torsional oscillation may be caused. © 1999 Scripta Technica, Electr Eng Jpn, 128(4): 25–37, 1999     

Two‐switch flyback PWM DC–DC converter in discontinuous‐conduction mode

The two‐switch flyback DC–DC converter is an extended version of the conventional single‐switch flyback converter. An additional switch and two clamping diodes serve as a simple, but an effective way to limit the switch overvoltages, which occur in the conventional single‐switch flyback converter due to the ringing of the resonant circuit formed by the transformer leakage inductance and the transistor output capacitance. The clamping diodes in the two‐switch flyback topology clamp the maximum voltage across each switch equal to the DC input voltage. This paper presents a detailed analysis and design procedure of the diode‐clamped two‐switch flyback converter operated in discontinuous‐conduction mode (DCM). A comparison of power losses of the two‐switch and the single‐switch flyback converters is given. The two‐switch flyback converter was bread‐boarded to validate the theoretical analysis. Experimental results from a 20‐V/30‐W, 100‐kHz laboratory prototype verified that the maximum switch voltage is limited to the DC input voltage. Copyright © 2010 John Wiley & Sons, Ltd.     

Sampled‐data poles,zeros, and modeling for current‐mode control

Exact and approximate sampled‐data models in closed forms are derived for switching DC–DC converters under peak/valley current‐mode control. The corresponding sampled‐data poles and zeros in closed forms are also derived. The location and stability conditions of the poles and zeros, boundary conditions of subharmonic instability, and nulling of the audio‐susceptibility are also derived. It is proved that the stable operating range of the source voltage is linearly proportional to the ramp slope. The sampled‐data models agree with previous experiment results and accurately predict the subharmonic instability. The different view from the sampled‐data model about the number and stability (minimum phase) of pole and zero does not necessarily invalidate the traditional continuous‐time averaged model. However, this different view gives better prediction about converter dynamics and is useful for the analog or digital controller design for DC–DC converters. Copyright © 2011 John Wiley & Sons, Ltd.     

A systematic approach to designing a wide‐current range,MOS capacitor‐based switched‐capacitor DC‐DC converter with an augmenting LDO

Switched‐capacitor DC‐DC converters (SC DC‐DC) are analyzed for loss sources, voltage regulation integrity, start‐up latency, and ripple size, while the trade‐offs between these metrics are derived. These analyses are used to design a SC DC‐DC that achieves high efficiency in a wide load current range. Four‐way interleaving was employed to reduce the output ripple and efficiency loss due to this ripple. The design can be reconfigured to achieve gains of 1/3 and 2/5 for inputs ranging between 1.4 and 3.6 V to generate output voltage range of 0.4 to 1.27 V and can supply peak load current of 22 mA. It uses thin‐oxide MOS capacitors for their high density and achieves 75.4% peak efficiency with an input frequency of 100 MHz and a load capacitor of 10 nF. An augmenting LDO that only regulates during sudden load transients helps the converter respond fast to these transients. The chip was implemented using a 65‐nm standard CMOS process.     

Characteristic Analysis of a Micro DC‐DC Converter for Portable Electronic Devices and an Improvement of Transient Response Characteristic

This paper describes the characteristic analysis of a micro DC‐DC converter which integrates inductor, controller and switching devices, and the improvement of the transient response characteristic. The steady‐state operation and the efficiency characteristics of the micro DC‐DC converter are presented as experimental data. The static characteristics are theoretically analyzed with consideration of the DC current characteristics of the inductor. The load transient response characteristics of the micro DC‐DC converter are also analyzed experimentally and theoretically. In addition, the factors responsible for the overshoot and undershoot of the output voltage when the load changes are discussed. Finally, a clamp circuit for reducing the overshoot and undershoot of the output voltage when the load changes is proposed. © 2011 Wiley Periodicals, Inc. Electr Eng Jpn, 175(3): 56–64, 2011; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.21081