A new topology for nonisolated multiport zero voltage switching dc‐dc converter

In this paper, a new multiport zero voltage switching dc‐dc converter is proposed. Multiport dc‐dc converters are widely applicable in hybrid energy generating systems to provide substantial power to sensitive loads. The proposed topology can operate in 3 operational modes of boost, buck, and buck‐boost. Moreover, it has zero voltage switching operation for all switches and has the ability to eliminate the input current ripple; also, at low voltage side, the input sources can be extended. In addition, it has the ability of interfacing 3 different voltages only by using 3 switches. In this paper, the proposed topology is analyzed theoretically for all operating modes; besides, the voltage and current equations of all components are calculated. Furthermore, the required soft switching and zero input currents ripple conditions are analyzed. Finally, to demonstrate the accurate performance of the proposed converter, the Power System Computer Aided Design(PSCAD)/Electro Magnetic Transient Design and Control(EMTDC) simulation and experimental results are extracted and presented.     

Performance analysis and calculation of critical inductance and output voltage ripple of a simple non‐isolated multi‐input bidirectional DC‐DC converter

In this paper, a simple non‐isolated multiple input (MI) bidirectional DC‐DC topology is proposed which can operate in buck, boost, or buck‐boost modes. The proposed topology utilizes a battery pack to realize the bidirectional power flow operation especially when the input sources are non‐storable ones. The excess energy of input sources can be stored in the battery and be injected to the load, when required. Simultaneous or independent power transfer of input sources is also provided. For better evaluation, the proposed topology has been compared with several recently presented novel topologies, from view point of number of inductors, capacitors, switches, and diodes. Comparison results show that the proposed topology utilizes less number of components (switches, inductors, capacitors, and current sensors) which can reduce the size, cost, and complexity of converter. Different operational modes of the proposed topology (unidirectional buck, boost, buck‐boost modes, and bidirectional mode) have been presented. Also, boost mode of the proposed topology has been investigated in detail, from design point of view, and generalized relationships have been proposed for calculation of critical inductance (CI) and output voltage ripple (OVR) of proposed n‐input boost topology. To validate proposed theoretical concepts, the proposed topology has been modeled and simulated in PSCAD/EMTDC software, and the 3‐input boost version has been experimentally implemented. Simulation and experimental results confirm appropriate performance of the proposed topology.     

A soft‐switching high step‐up DC‐DC converter with a single magnetic component

A soft‐switching high step‐up DC‐DC converter with a single magnetic component is presented in this paper. The proposed converter can provide high voltage gain with a relatively low turn ratio of a transformer. Voltage doubler structure is selected for the output stage. Due to this structure, the voltage gain can be increased, and the voltage stresses of output diodes are clamped as the output voltage. Moreover, the output diode currents are controlled by a leakage inductance of a transformer, and the reverse‐recovery loss of the output diodes is significantly reduced. Two power switches in the proposed converter can operate with soft‐switching due to the reflected secondary current. The voltages across the power switches are confined to the clamping capacitor voltage. Steady‐state analysis, simulation, and experimental results for the proposed converter are presented to validate the feasibility and the performance of the proposed converter. Copyright © 2012 John Wiley & Sons, Ltd.     

A new interleaved bidirectional dc/dc converter with zero voltage switching and high voltage gain: analyses,design and simulation

In this paper, a new interleaved non‐isolated bidirectional dc–dc converter with capability of zero voltage switching and high voltage gain is proposed. In the proposed converter by using two coupled inductors and one capacitor, the voltage gain is extended. Moreover, by using only an auxiliary circuit that includes an inductor and two capacitors, the zero voltage switching (ZVS) of two used switches in the first phase of converter can be achieved. The ZVS operation of two used switches in the second phase is always obtained without using any extra auxiliary circuit. This converter similar to other interleaved converters has low input current ripple and low current stress on switches. In this paper, the proposed converter is analyzed in all operating modes, and also the voltage gain, required conditions for ZVS operation of switches, voltage and current stresses of all switches, and the value of input current ripple in both boost and buck operations are obtained. Finally, the accuracy performance of the proposed converter is verified through simulation results in EMTDC/PSCAD software. Copyright © 2017 John Wiley & Sons, Ltd.     

A high‐voltage gain nonisolated noncoupled inductor based multi‐input DC‐DC topology with reduced number of components for renewable energy systems

This paper proposes a modular nonisolated noncoupled inductor‐based high‐voltage gain multi‐input DC‐DC converter. Despite the high‐voltage gain of the proposed topology, the average of normalized voltage stress (NVS) on its switches/diodes is low. This property leads to less loss and cost of switches/diodes. Using the same number of components, the proposed topology produces higher voltage gains, in comparison with recently presented high step‐up topologies. Also, the proposed topology utilizes less number of components (capacitors, inductors, diodes, and switches) for producing a desired voltage gain, which can reduce the size, mass, cost, complexity, and losses and improve the efficiency of converter. Continuous current of input sources is another main advantage of the proposed topology. All the abovementioned characteristics have made the proposed topology very suitable for renewable energy systems (or even hybrid/electric vehicles). Design considerations of the proposed topology have also been presented. For better evaluation, the proposed topology has been compared with some of recently presented high step‐up structures, from viewpoints of producible voltage gain, number of components, and normalized voltage stress (NVS) on switches/diodes. Finally, the prototype of 2‐input version has been experimentally implemented. Obtained experimental results confirm appropriate performance of the proposed topology.     

Soft switching DC/DC converter with high voltage gain and less current ripple

A new soft switching three‐level converter with two DC/DC circuits in the primary side and current double rectifiers in the secondary side is presented to realize the zero‐voltage switching operation, reduce the transformer secondary winding turns and the output current ripple, and lessen the voltage rating of rectifier diodes. Two DC/DC pulse‐width modulation circuits sharing same power switches with interleaved half switching cycle are adopted in the proposed converter to reduce the current rating of transformer primary windings. Two inductors and four diodes are adopted in the secondary side to achieve current double rectifier, reduce output ripple current, and decrease the transformer secondary winding turns. Based on the pulse‐width modulation scheme, the power switchers can be turned on at zero‐voltage switching operation. Laboratory experiments with a 1.44 kW prototype are provided to verify the theoretical analysis. Copyright © 2016 John Wiley & Sons, Ltd.     

Analysis and implementation of a high‐efficiency zero‐voltage‐zero‐current‐switching DC–DC converter

A high‐efficiency zero‐voltage‐zero‐current‐switching DC–DC converter with ripple‐free input current is presented. In the presented converter, the ripple‐free boost cell provides ripple‐free input current and zero‐voltage switching of power switches. The resonant flyback cell provides zero‐voltage switching of power switches and zero‐current switching of the output diode. Also, it has a simple output stage. The proposed converter achieves high efficiency because of the reduction of the switching losses of the power switches and the output diode. Detailed analysis and design of the proposed converter are carried out. A prototype of the proposed converter is developed and its experimental results are presented for validation. Copyright © 2011 John Wiley & Sons, Ltd.     

A novel low‐loss control strategy for bidirectional DC–DC converter

Bidirectional DC–DC converter with phase‐shift control is commonly used for hybrid electric vehicle and fuel‐cell vehicle applications. This converter is characterized by simple circuit topology and soft‐switching implementation without additional devices. Despite these advantages, the efficiency is poor at light load condition because of high switching and conduction losses caused by high RMS inductor current. To achieve zero‐voltage switching (ZVS) for all power MOSFETs, a constant offset inductor current is maintained to conduct the antiparallel body diodes before MOSFETs turn on. A control strategy of combining duty ratio and phase‐shift modulation is proposed to reach the constant offset current. By reaching the constant offset current, the RMS inductor current can be reduced significantly, and ZVS can be achieved in all load variation ranges, resulting in high efficiency. A 2.5‐kW prototype is implemented to verify the control scheme, and a minimum efficiency of 97.3% is achieved at light load condition. Copyright © 2017 John Wiley & Sons, Ltd.     

具有低输入电流纹波带耦合电感的双向DC-DC变换器

针对燃料电池发电系统输出电压低和输入电流纹波大的问题,本文设计了一种新型带耦合电感的双向DC-DC变换器。该变换器利用超级电容器减少电流纹波对燃料电池的冲击从而提高燃料电池的发电效率,同时通过改变占空比和耦合电感的匝数比来提高输出电压增益。在Matlab/Simulink软件中创建仿真模型,采用平均电流模式搭建控制电路,并详细地分析升压和降压模式下变换器的开关状态与工作特性。仿真结果为：变换器的输入电流纹波约为1%,在耦合电感变比为1时升压电压增益最高为16。结果表明本文所提变换器可以在满足燃料电池发电系统对低频电流纹波的要求同时实现高电压增益,验证了所提出拓扑的可行性。     

Series resonant high‐voltage DC–DC converter with reduced component count

This paper proposes a novel zero‐current‐switching series resonant high‐voltage DC–DC converter with reduced component count. The series resonant inverter in the proposed topology has two power switches (insulated‐gate bipolar transistors, IGBTs), two resonant capacitors, and only one high‐voltage transformer (HVT) with center‐tapped primary windings. The power switches are connected in the form of a half‐bridge network. The leakage inductances of the transformer's primary windings together with the resonant capacitors form two series resonant circuits. The series resonant circuits are fed alternately by operating the power switches with interleaved half switching cycle. The secondary winding of the HVT is connected to a bridge rectifier circuit to rectify the secondary voltage. The converter operates in the discontinuous conduction mode (DCM) and its output voltage is regulated by pulse frequency modulation. Therefore, all the power switches turn on and off at the zero‐current switching condition. The main features of the proposed converter are its lower core loss, lower cost, and smaller size compared to previously proposed double series resonant high voltage DC–DC converters. The experimental results of a 130‐W prototype of the proposed converter are presented. The results confirm the excellent operation and performance of the converter. © 2016 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

Analysis and implementation of a step–up power converter with input current ripple cancelation

This paper proposes a power electronics converter capable of canceling the input current ripple at preselected duty cycle. The proposed converter is an extended topology of a buck–boost converter aided by a boost‐type converter that improves the quality of the current drawn from the direct current source. The voltage gain of the proposed converter is increased as well, with a minimum of extra component added to the original buck–boost power converter. These features make the proposed converter ideal for low voltage generation sources, such as photovoltaic panel and fuel cell applications. Along this paper, the state space mathematical model is developed to provide the key design guidelines. The theoretical analysis is validated through computer simulation and hardware prototyping.     

一种低输入纹波电流的高增益软开关Boost变换器

针对新能源应用系统中输出电压低的问题,提出一种低输入纹波电流的高增益软开关Boost变换器。该变换器通过在二次型Boost电路的基础上加入耦合电感和倍压电路来提高增益。理论分析与实验结果表明该变换器具有高增益的同时还具有以下优点:1)输入电流为Boost电感电流,相对于耦合电感型变换器来说,其纹波得到大幅降低;2)所有开关管均实现了软开关,降低了开关损耗;3)由于漏感的作用,倍压电路中的二极管反向恢复损耗几乎为0;4)所有元器件的电压应力均低于输出电压,可采用低耐压元器件来降低导通损耗;5)耦合电感在开关导通和关断期间均传递了能量,提高了利用率,从而可提高功率密度。     

Non‐isolated large step‐down voltage conversion ratio converter with non‐pulsating output current

A non‐isolated dual half‐bridge large step‐down voltage conversion ratio converter with non‐pulsating output current, utilizing one coupled inductor, one energy‐transferring capacitor, and one output inductor, is presented herein. The coupled inductor is connected between the input voltage and the output inductor and plays a role to step down the input voltage. Furthermore, the output inductor is used not only to further step down the voltage but also to provide a non‐pulsating output current. Moreover, the proposed converter can achieve zero‐voltage switching. In this study, detailed theoretical deductions and some experimental results of a prototype with 48 V input voltage, 3.3 V output voltage, and 10 A output current are provided to demonstrate the feasibility and effectiveness of the proposed converter. Copyright © 2015 John Wiley & Sons, Ltd.     

A non‐isolated high step‐up DC‐DC converter with integrated 3 winding coupled inductor and reduced switch voltage stress

In this paper, a non‐isolated high step‐up dc‐dc converter based on coupled inductor is proposed. The proposed converter can be used in renewable energy applications. In suggested converter, the high voltage is achieved using 3‐winding coupled inductor, which leads to low voltage rate of the switch. A clamp circuit is used to recycle the leakage inductance energy. Also, the clamp circuit prevents the creation of voltage spikes on semiconductor devices and causes the voltage stress of elements are limited to less than the output voltage. The presented theoretical analyses show that the operation of suggested converter in continuous conduction mode needs to small magnetic inductor. Therefore, the size of coupled inductor's core is reduced, and so the size and cost of presented converter will be decreased. Analysis of the proposed converter is provided with laboratory results to verify its performance.     

A high step‐up half‐bridge DC/DC converter with a special coupled inductor for input current ripple cancelation and extended voltage doubler circuit for power conditioning of fuel cell systems

This paper presents a high step‐up soft switched dc–dc converter having the feature of current ripple cancelation in the input stage that is specialized for power conditioning of fuel cell systems. The converter comprises a special half‐bridge converter and a rectifier stage based upon the voltage‐doubler circuit, in which the coupled‐inductor technology is amalgamated with switched‐capacitor circuit. The input current with no ripple is the principal characteristics of this topology that is achieved by utilizing a small coupled inductor. In addition, the low clamped voltage stress across both power switches and output diodes is another advantage of the proposed converter, which allows employing the metal–oxide–semiconductor field‐effect transistors with minuscule on‐state resistance and diodes with lower forward voltage‐drop, and thereby, the semiconductors' conduction losses diminish considerably. The inherent nature of this topology handles the switching scheme based on the asymmetrical pulse width modulation in order for switches to establish the zero voltage switching, leading to lower switching losses. Besides, because of the absence of the reverse‐recovery phenomenon, all diodes turn off with zero current switching. At last, a 250‐W laboratory prototype with the input voltage 24 V and output voltage 380 V is implemented to verify the especial features of the proposed converter. Copyright © 2015 John Wiley & Sons, Ltd. Copyright © 2015 John Wiley & Sons, Ltd.     

A gain/efficiency‐enhanced bidirectional switched‐capacitor DC‐DC converter

A closed‐loop gain/efficiency‐enhanced bidirectional switched‐capacitor converter (BSCC) is proposed by combining an adaptive‐conversion‐ratio (ACR) phase generator and pulse‐width‐modulation (PWM) controller for bidirectional step‐up/down DC‐DC conversion and regulation. For realizing gain‐enhanced, the power part consists of one m_c‐stage cell and one n_c‐stage cell in cascade between low‐voltage (LV) and high‐voltage (HV) sides to boost HV voltage into m_c × n_c times voltage of LV source at most, or convert LV voltage into 1/(m_c × n_c) times voltage of HV source at most. For realizing efficiency‐enhanced, the ACR idea with adapting stage number m, n is built in the phase generator to obtain a suitable step‐up/down gain: m × n or 1/(m × n) (m = 1, 2, …, m_c, n = 1, 2, …, n_c). Further, the output regulation and robustness to source/loading variation can be enhanced by PWM on the LV/HV sides. Some theoretical analysis and control design are included as: modeling, steady‐state analysis, conversion ratio, efficiency, capacitance selection, and control design. Finally, the performance of this scheme is verified experimentally on a BSCC prototype, and all results are illustrated to show the efficacy of this scheme. Copyright © 2012 John Wiley & Sons, Ltd.     

LLC resonant DC–DC converter with series‐connected primary windings of transformer

This paper proposes a zero‐voltage switching (ZVS) LLC resonant step up DC–DC converter with series‐connected primary windings of the transformer. The series resonant inverter in the proposed topology has two power switches (MOSFETs), two resonant capacitors, two resonant inductors, and only one transformer with center‐tapped primary windings. The power switches are connected in the form of a half‐bridge network. Resonant capacitors and inductors along with the primary windings of the transformer form two series resonant circuits. The series resonant circuits are fed alternately by operating the power switches with an interleaved half switching cycle. The secondary winding of transformer is connected to a bridge rectifier circuit to rectify the output voltage. The converter operates within a narrow frequency range below the resonance frequency to achieve ZVS, and its output power is regulated by pulse frequency modulation. The converter has lower conduction and switching losses and therefore higher efficiency. The experimental results of a 500‐W prototype of proposed converter are presented. The results confirm the good operation and performance of the converter. © 2014 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

Single switch quadratic boost converter with continuous input current for high voltage applications

In this paper, a novel non-isolated very high step-up DC-DC converter is presented. The introduced converter benefits from various advantages, namely, very high voltage gain, low voltage stress on the active switch, and continuous input current with low ripple. Therefore, the presented converter is suitable for renewable energy applications. In addition, the energy of the leakage inductance of the coupled inductor is successfully recovered, and the voltage spike of the active switch is clamped during the turn-off process. Hence, a switch with low can be used, which decreases the conduction losses as well as cost of the converter. Furthermore, the voltage stress of the output diode is decreased, which reduces the reverse recovery problem. The steady-state analysis and design considerations of the proposed converter are discussed. Finally, the theoretical analysis is validated with the experimental results at an output power of 150 W.     

Expandable interleaved high voltage gain boost DC-DC converter with low switching stress

In this paper, an interleaved DC-DC step-up boost converter with high voltage conversion ratio and low voltage stresses on switches and diodes is proposed. The proposed converter has low average current passing through the diodes and switches and low input current ripple as a feature of interleaved converters. The voltage gain of the proposed converter can be increased by adding more diode-capacitor modules; therefore, the proposed converter has expandable structure. In addition, by implementing more diode-capacitor modules, the switching stresses would be more decreased. Also, to evaluate the performance of the proposed converter, it is compared with other similar presented circuits in the literature. The proposed converter is not only able to provide higher voltage gain but also has lower voltage stresses on switches and diodes. Consequently, switches and diodes with low voltage ratings can be selected. Theoretical analysis is provided in this study for each operation mode and the average current through the switches, diodes and inductors, voltage stresses on switches and diodes, voltage gain, and input current ripple are calculated. Finally, to demonstrate the accuracy performance of the proposed converter, a 450-W prototype is implemented practically.     

Design and implementation of a high‐efficiency bidirectional DC‐DC Converter for DC micro‐grid system applications

This paper studies the design and implementation of a non‐isolated dual‐half‐bridge bidirectional DC‐DC converter for DC micro‐grid system applications. High efficiency can be achieved under wide‐range load variations by the zero‐voltage‐switching features and an adaptive phase‐shift control method. A three‐stage charging scheme is designed to meet the fast‐charging demand and prolong the lifetime of LiFePO₄ batteries. A digital‐signal‐processing control IC is used to realize the power flow control, DC‐bus voltage regulation, and battery charging/ discharging of the studied bidirectional DC‐DC converter. Finally, a 10 kW prototype converter with Enhanced Controller Area Network communication function is built and tested for micro‐grid system applications. A light‐load efficiency over 96% and a rated‐load efficiency over 98% can be achieved. Copyright © 2013 John Wiley & Sons, Ltd.