用Timoshenko梁修正理论研究泡沫金属铝合金梁的动力响应

采用Timoshenko梁修正理论研究了泡沫金属铝合金梁的动力响应问题。应用Timoshenko梁修正理论建立了泡沫金属铝合金梁的振动方程,求得了其自振频率表达式及其在简谐荷载作用下强迫振动的解析解。通过实例计算,把球形泡沫铝合金梁与其它泡沫铝合金梁进行了对比分析,得出了球形泡沫金属铝合金梁的动力性能优于其它泡沫铝合金梁的动力性能。     

功能梯度材料Timoshenko型剪切梁的自由振动分析

基于Timoshenko梁理论,研究各向异性功能梯度材料梁的自由振动。假设材料参数沿梁厚度方向按同一函数规律变化,建立了功能梯度材料梁的振动方程,求得简支条件下其自振频率表达式。通过算例,给出指数函数梯度变化Timoshenko梁的自振频率和模态图,结果表明不同梯度变化对材料结构动力响应有较大影响。该方法为发展功能梯度材料梁的设计与数值计算提供了理论依据。     

热冲击下轴向运动FGM梁的自由振动分析

基于Timoshenko梁理论研究两端夹紧、一端夹紧一端简支、两端简支三种不同边界条件下的轴向运动功能梯度材料(FGM)梁在热冲击载荷作用下的自由振动响应。利用Hamilton原理推导热冲击下轴向运动FGM梁的自由振动控制微分方程,并采用分离变量法求解一维热传导方程。通过微分求积法(DQM)在梁的长度方向进行离散,将原方程转化为四阶广义特征值问题,求解FGM梁自由振动的无量纲固有频率并进行特性分析。考虑了不同热冲击载荷,不同梯度指数和不同轴向运动无量纲速度对FGM梁自振频率的影响。结果表明:热冲击载荷越大,对降低FGM梁的固有频率的效果越明显;在轴向运动速度和热流输入不改变的情况下,逐渐增大材料梯度指数会使FGM梁的固有频率随之减小;FGM梁对热冲击短时间内有减缓作用,相对于均匀材料一阶失稳所需时间更长,受到热冲击的FGM梁在轴向运动时也更快达到失稳状态。     

基于能量有限元法的功能梯度梁振动分析

功能梯度材料(Functionally Graded Material,FGM)由于其优良的结构性能和重要的应用价值,近些年来得到了广泛的研究和关注。采用能量有限元法对功能梯度梁和耦合梁的弯曲振动特性进行研究,推导了功能梯度材料梁的能量密度控制方程、能量有限元矩阵方程以及耦合梁的能量有限元方程,从而得到梁中的能量密度和能量流。以一简支功能梯度梁为例,分别采用该方法和传统有限元法计算了梁弯曲振动时的能量密度,通过对比验证了能量有限元法求解的准确性。在此基础上进一步对耦合功能梯度梁结构的能量密度和能量流进行了求解,得到其能量分布特征。该研究为基于能量有限元法分析复杂功能梯度材料结构的振动特性提供了理论基础。     

热冲击作用下轴向运动梁的振动特性研究

研究了两端简支不可移、轴向运动梁在热冲击作用下的横向振动特性,根据Timoshenko梁理论和Hamilton原理建立了梁的横向振动控制方程,采用微分求积法求解了梁的横向振动问题,分析了热冲击和轴向运动效应对梁固有特性的影响。研究发现:热冲击引起的梁的等效热轴力、热弯矩和弹性模量变化三因素中,热轴力对梁固有频率的影响起主导作用,材料的弹性模量变化和热弯矩起次要作用;当热冲击载荷大于或等于梁的临界压力时,达到梁的第一阶失稳模态;热冲击和轴向运动效应都会降低梁的固有频率,它们的联合作用会导致模态之间的耦合现象,使梁更易达到失稳状态。     

轴向运动黏弹性Timoshenko梁横向非线性强受迫振动

研究轴向运动黏弹性Timoshenko梁横向非线性强受迫振动的稳态响应。由广义Hamilton变分原理推导出轴向运动黏弹性Timoshenko梁横向振动的控制方程及相应的边界条件。模型中考虑剪切模量、转动惯量对梁的影响。黏弹性本构关系中运用Kelvin模型并引入物质时间导数。对控制方程施用直接多尺度法,建立强受迫共振的可解性条件,得到稳态响应振幅与激励频率关系曲线。应用Routh-Hurwitz判据判断稳态响应振幅的稳定性。利用数值结果给出不同参数下,如非线性系数、激励振幅与黏弹性阻尼等对稳态幅频响应及稳定性影响。     

沿轴向指数分布的功能梯度Timoshenko梁的频率精确解

通过对状态空间变量进行变量替换,求得了沿轴向指数分布的功能梯度Timoshenko梁的状态空间传递矩阵方程。通过传递矩阵法计算了多种边界条件下结构固有频率的精确解,并与解析解进行对比。通过分析梯度参数对结构固有频率与模态振型的影响,该计算结果表明频率与材料梯度变量之间的关系曲线是连续光滑的,并未出现部分文献中的跳跃现象,并且采用有限元法该计算结果进行验证。通过对比不同梁理论的计算结果,定量的分析了剪切刚度和转动惯量对结构固有频率的影响。计算结果表明,该方法物理概念清晰,降低问题求解难度的同时可以减少计算量。     

功能梯度材料梁在后屈曲构型附近的自由振动

基于轴线可伸长杆的几何非线性理论,建立了由陶瓷和金属两种材料组成的功能梯度(FGM)梁在轴向载荷作用下后屈曲横向自由振动的精确模型,采用打靶法数值求解了一端可移简支一端固定的功能梯度梁在后屈曲附近的小振幅自由振动,获得了线性振动的响应,给出了不同梯度指标下FGM梁前三阶固有频率与载荷之间的特征关系曲线.数值结果表明,屈曲前各阶频率随轴向力的增加而降低,而屈曲后轴向力对各阶频率影响不同     

周期结构空腹梁的动态特性研究

设计了一种内部周期性挖空的梁，它在中高频具有良好的带通和带阻特性，带阻频率范围内的弹性波不能传播。空腹梁由周期单元串联而成，把周期单元分解成薄梁和刚性联接杆等子结构，推导了Timoshenko梁纵向、弯曲振动导纳，给出了刚性联接杆振动导纳，利用传递矩阵法计算得到了周期结构空腹梁的力传递率和带隙位置。数值模拟计算表明，当激励频率在周期结构的阻带之内时，周期结构空腹梁上的位移响应和传递到基础的力响应将大大衰减。     

一阶剪切理论下功能梯度梁与均匀梁静态解之间的相似关系

基于一阶剪切理论,研究了功能梯度材料Timoshenko 梁的静态弯曲解与对应的均匀材料梁的解的线性转换关系。通过比较功能梯度材料梁和均匀材料梁的无量纲控制方程,发现了它们弯曲解的线性相关性。在给定材料弹性模量沿横向非均匀变化规律后,可将功能梯度材料Timoshenko 梁在静载荷作用下的弯曲变形解用相同尺寸、相同载荷以及相同边界条件下的均匀材料Timoshenko 梁的弯曲变形解线性表示。这样,可将非均匀Timoshenko 梁弯曲问题的求解转化为对应的均匀材料Timoshenko 梁弯曲问题的求解和转换系数的计算,从而使得求解过程得以简化。     

Free vibration analysis of size-dependent functionally graded microbeams based on the strain gradient Timoshenko beam theory

Investigated herein is the free vibration characteristics of microbeams made of functionally graded materials (FGMs) based on the strain gradient Timoshenko beam theory. The material properties of the functionally graded beams are assumed to be graded in the thickness direction according to the Mori–Tanaka scheme. Using Hamilton’s principle, the equations of motion together with corresponding boundary conditions are obtained for the free vibration analysis of FGM microbeams including size effect. A detailed parametric study is performed to indicate the influences of beam thickness, dimensionless length scale parameter, and slenderness ratio on the natural frequencies of FGM microbeams. Moreover, a comparison between the various beam models on the basis of the classical theory (CT), modified couple stress theory (MCST), and strain gradient theory (SGT) is presented for different values of material property gradient index. It is observed that the value of gradient index play an important role in the vibrational response of the microbeams of lower slenderness ratios. It is further observed that by increasing the length-to-thickness ratio of the microbeam, the value of dimensionless natural frequency tends to decrease for all amounts of the gradient index.     

Free vibration analysis of size-dependent functionally graded microbeams based on the strain gradient Timoshenko beam theory

Investigated herein is the free vibration characteristics of microbeams made of functionally graded materials (FGMs) based on the strain gradient Timoshenko beam theory. The material properties of the functionally graded beams are assumed to be graded in the thickness direction according to the Mori–Tanaka scheme. Using Hamilton’s principle, the equations of motion together with corresponding boundary conditions are obtained for the free vibration analysis of FGM microbeams including size effect. A detailed parametric study is performed to indicate the influences of beam thickness, dimensionless length scale parameter, and slenderness ratio on the natural frequencies of FGM microbeams. Moreover, a comparison between the various beam models on the basis of the classical theory (CT), modified couple stress theory (MCST), and strain gradient theory (SGT) is presented for different values of material property gradient index. It is observed that the value of gradient index play an important role in the vibrational response of the microbeams of lower slenderness ratios. It is further observed that by increasing the length-to-thickness ratio of the microbeam, the value of dimensionless natural frequency tends to decrease for all amounts of the gradient index.     

Vibration analysis of a functionally graded beam under a moving mass by using different beam theories

Vibration of a functionally graded (FG) simply-supported beam due to a moving mass has been investigated by using Euler–Bernoulli, Timoshenko and the third order shear deformation beam theories. The material properties of the beam vary continuously in the thickness direction according to the power-law form. The system of equations of motion is derived by using Lagrange’s equations. Trial functions denoting the transverse, the axial deflections and the rotation of the cross-sections of the beam are expressed in polynomial forms. The constraint conditions of supports are taken into account by using Lagrange multipliers. In this study, the effects of the shear deformation, various material distributions, velocity of the moving mass, the inertia, Coriolis and the centripetal effects of the moving mass on the dynamic displacements and the stresses of the beam are discussed in detail. To validate the present results, the dynamic deflections of the beam under a moving mass are compared with those of the existing literature and a comparison study for free vibration of an FG beam is performed. Good agreement is observed. The results show that the above-mentioned effects play a very important role on the dynamic responses of the beam and it is believed that new results are presented for dynamics of FG beams under moving loads which are of interest to the scientific and engineering community in the area of FGM structures.     

基于物理中面FGM梁的非线性力学行为

当坐标面置于功能梯度材料(FGM)梁的物理中面上时,其本构方程中,面内力与弯矩并不耦合,这使得问题的控制方程以及边界条件得以简化.该文利用物理中面概念,基于一阶非线性梁理论,导出了FGM梁的基本方程,分析研究了热载荷作用下FGM梁的过屈曲、弯曲以及在这些构形上的振动等问题.假设功能梯度材料性质只沿梁厚度方向,并按成分含...     

The modified couple stress functionally graded Timoshenko beam formulation

In this paper, a size-dependent formulation is presented for Timoshenko beams made of a functionally graded material (FGM). The formulation is developed on the basis of the modified couple stress theory. The modified couple stress theory is a non-classic continuum theory capable to capture the small-scale size effects in the mechanical behavior of structures. The beam properties are assumed to vary through the thickness of the beam. The governing differential equations of motion are derived for the proposed modified couple-stress FG Timoshenko beam. The generally valid closed-form analytic expressions are obtained for the static response parameters. As case studies, the static and free vibration of the new model are respectively investigated for FG cantilever and FG simply supported beams in which properties are varying according to a power law. The results indicate that modeling beams on the basis of the couple stress theory causes more stiffness than modeling based on the classical continuum theory, such that for beams with small thickness, a significant difference between the results of these two theories is observed.     

轴向运动功能梯度悬臂梁动力学分析

针对轴向运动悬臂梁振动会影响系统的安全性、稳定性问题,对功能梯度悬臂梁振动特性进行分析,利用广义哈密尔顿原理及假设模态法导出系统动力学方程。结果表明,功能梯度悬臂梁的横向位移与轴向位移耦合,功能梯度材料在厚度方向按体积分数函数呈指数变化,且梁自由端有集中质量块。并讨论材料指数及末端集中质量大小对振动影响,分析梁在伸展、收缩时的运动特性。所得结论可为类似结构的动力学分析、设计提供依据。     

Dynamic behaviour of edge-cracked shear deformable functionally graded beams on an elastic foundation under a moving load

This paper studies the dynamic response of functionally graded beams with an open edge crack resting on an elastic foundation subjected to a transverse load moving at a constant speed. It is assumed that the material properties follow an exponential variation through the thickness direction. Theoretical formulations are based on Timoshenko beam theory to account for the transverse shear deformation. The cracked beam is modeled as an assembly of two sub-beams connected through a linear rotational spring. The governing equations of motion are derived by using Hamilton’s principle and transformed into a set of dynamic equations through Galerkin’s procedure. The natural frequencies and dynamic response with different end supports are obtained. Numerical results are presented to investigate the influences of crack location, crack depth, material property gradient, slenderness ratio, foundation stiffness parameters, velocity of the moving load and boundary conditions on both free vibration and dynamic response of cracked functionally graded beams.     

压电功能梯度层合梁的力-电-热耦合梁单元及最优振动控制

给出了一个压电功能梯度层合梁振动分析的两节点力-电-热耦合梁单元,并将其用于功能梯度层合梁的振动最优控制。在这个多场耦合梁单元中,功能梯度材料的等效力学性能用Voigt或Mori-Tanaka模型表征;梁的位移场用Shi改进的三阶剪切变形板理论描述;压电层的电势场用Layer-wise理论分层表征,且呈高阶非线性电势场的压电层可离散成数个子层。用Hamilton原理推导了压电功能梯度梁的力-电-热耦合单元列式,用拟协调元法给出了多场耦合梁单元的高计算效率的显式单元刚度矩阵,以及采用线性二次型(LQR)最优控制算法进行压电功能梯度层合梁的最优振动控制。使用所得力-电-热耦合梁单元进行了压电功能梯度层合梁的静力和动力分析。数值算例表明,所得力-电-热耦合梁单元可靠、准确和高效,LQR最优控制算法得到最优控制电压可有效抑制功能梯度梁的振动且实现控制系统能量的优化。     

Size effect on dynamic stability of functionally graded microbeams based on a modified couple stress theory

Dynamic stability of microbeams made of functionally graded materials (FGMs) is investigated in this paper based on the modified couple stress theory and Timoshenko beam theory. This non-classical Timoshenko beam model contains a material length scale parameter and can interpret the size effect. The material properties of FGM microbeams are assumed to vary in the thickness direction and are estimated though Mori–Tanaka homogenization technique. The higher-order governing equations and boundary conditions are derived by using the Hamilton’s principle. The differential quadrature (DQ) method is employed to convert the governing differential equations into a linear system of Mathieu–Hill equations from which the boundary points on the unstable regions are determined by Bolotin’s method. Free vibration and static buckling are also discussed as subset problems. A parametric study is conducted to investigate the influences of the length scale parameter, gradient index and length-to-thickness ratio on the dynamic stability characteristics of FGM microbeams with hinged–hinged and clamped–clamped end supports. Results show that the size effect on the dynamic stability characteristics is significant only when the thickness of beam has a similar value to the material length scale parameter.