共查询到16条相似文献,搜索用时 109 毫秒
1.
由于氮压机级间冷却器严重结垢,氮压机压缩气体的能力大大减小而且喘振现象频繁发生。通过对氮压机水路进行加装反冲洗阀的改造,并采用改进后的循环酸洗法对氮压机进行酸洗,从根本上解决了氮压机级间冷却器严重结垢问题,取得了降本增效的效果。简介氮压机的运行状况,详细阐述改进后的循环酸洗方法及具体实施过程,分析氮压机级间冷却器清洗后的效果,最后介绍循环酸洗法的推广应用。 相似文献
2.
简单介绍了国产三轴齿轮式10000m3/h氮压机的结构特点,分析了氮压机安装调试情况,最后就该氮压机与进口氮压机进行了比较。 相似文献
3.
4.
介绍马钢20000m3/h空分设备膨胀机油冷却器泄漏造成膨胀机进水以及氮压机五级气体冷却器泄漏引发氮压机进水的故障现象,阐述了处理措施及效果。 相似文献
5.
介绍了C90MX5M2型氮压机投运后出现的供气压力偏低,不能满足炼钢需求的现象。分析后认为原因是氮压机进气管路的压力摩擦损失太大,使进气压力不能满足氮压机的工艺要求。改善进气条件后氮压机运行正常。 相似文献
6.
简介了鞍钢35000m3/h空分设备流程,分析了自动变负荷存在的问题和降低氮压机能耗的理论依据,通过改变低压氮气和中压氮气的调节方式,实现增产氮气和降低氮压机能耗。 相似文献
7.
4MSGEP7/15型氮压机因为润滑油温度低而启动成功率低,根据环境温度,采取不同的润滑油加热方法,提高了氮压机润滑油的温度,使氮压机的轴振动值达标,启动成功率达到100%。介绍氮压机轴振动值大的原因分析过程和优化操作的具体实施方案。 相似文献
8.
介绍了因二级汽缸吸气阀螺栓跌入二级汽缸上部造成氮压机机身断裂的事故,分析了事故原因,最后提出了事故的解决方法和预防措施。 相似文献
9.
<正>济南钢铁公司氧气厂现有5台LW-40/8型氮压机,担负着供应总公司氮气的任务。长期以来,氮压机活塞杆带油严重,这一方面给活塞杆用氮气作为密封装置的4M12-59/30型氧压机造成隐患;另一方面增加了操作工定期清油的负担。 相似文献
10.
分析了中间抽气型三轴齿轮式氮压机的特点,对配置单台中间抽气型三轴齿轮式氮压机与配置两台氮压机两种方案进行比较后得出:前者一次性投资成本低、占地面积小、备品备件少、能耗和运行成本低。 相似文献
11.
12.
简介双螺杆空压机与两级螺杆空压机的结构和运行特点,由于两级螺杆空压机采用了两级串联压缩工艺、中间喷油冷却装置和大直径螺杆等,节能效果明显。通过实例计算,得出两级螺杆空压机比双螺杆空压机节能15%。 相似文献
13.
《低温学》2013
Mixed refrigerant Joule–Thomson (MR J–T) cryocoolers have been used to create cryogenic temperatures and are simple, efficient, cheap, and durable. However, compressors for MR J–T cryocoolers still require optimization. As the MR J–T cryocooler uses a commercial scroll compressor developed for air-conditioning systems, compressor overheating due to the use of less optimized refrigerants may not be negligible, and could cause compressor malfunction due to burn-out of scroll tip seals. Therefore, in the present study, the authors propose procedures to optimize compressor operation to avoid the overheating issue when the MR J–T cryocooler is used with a commercial oil lubricated scroll compressor, and the present experimental results obtained for a MR J–T cryocooler. A single stage 1.49 kW (2 HP) scroll compressor designed for R22 utilizing a mixture of nitrogen and hydrocarbons was used in the present study. As was expected, compressor overheating and irreversible high temperatures at a compressor discharge port were found at the beginning of compressor operation, which is critical, and hence, the authors used a water injection cooling system for the compressor to alleviate temperature overshooting. In addition, a portion of refrigerant in the high-pressure stream was by-passed into the compressor suction port. This allowed an adequate compression ratio, prevented excessive temperature increases at the compressor discharge, and eventually enabled the MR J–T cryocooler to operate stably at 121 K. The study shows that commercial oil lubricated scroll compressors can be used for MR J–T cryocooling systems if care is exercised to avoid compressor overheating. 相似文献
14.
对螺杆式制冷机组运行初始阶段的油温控制特点进行分析,发现开机时过低的冷冻油温度会使其溶解制冷剂的能力增强,从而使冷冻油黏度和润滑能力降低,加速螺杆式压缩机运动部件的机械磨损。而目前使用热力膨胀阀的油冷却系统会使供油温度不断大幅波动,并超出使用范围。采用带有加热器的油气分离器,并通过PLC控制器利用PID调节方式对电子膨胀阀开度进行自动调节,从而控制冷冻油温度,可使上述问题得到解决。 相似文献
15.
16.
简介了12000m3/h空分设备的运行状况,通过控制最佳的膨胀空气入上塔量、提高污氮气氮含量等优化操作措施,使空分设备的氧产量提高了2100m3/h,降低了能耗,空压机的运行也更稳定。 相似文献