低温沉积SiO2薄膜工艺的研究

利用等离子体增强化学气相沉积系统（PECVD）研究SiO2薄膜低温制备工艺,分析工艺条件对薄膜性能参数影响,通过调节射频功率优化薄膜应力,在150℃低温下获得接近零应力SiO2薄膜,薄膜沉积速率约为40nm／min,片内均匀性优于3％,折射率为1．46±0．003,并具有良好的附着力和抗蚀性能。由于沉积温度低,薄膜性能好,因此可以作为绝缘层或介质层,应用于柔性电子领域。     

热丝CVD大面积金刚石薄膜的生长动力学研究

在传统工业型热丝化学气相沉积（HFCVD）反应腔内，相关工艺参数取模拟计算优化值的条件下，采用XRD，SEM及Raman光谱等分析手段研究了单晶Si（100）上较大面积金刚石薄膜的动力学生长行为，讨论了晶格取向的变化规律。结果表明：优化工艺参数条件下，在模拟计算的衬底温度和气体温度分布均匀的区域内，沉积的金刚石薄膜虽存在一定的内应力，但整体薄膜连续、均匀，几何晶形良好，质量较高，生长速率达1．8μm／h。薄膜生长过程中晶形显露面受衬底温度和活性生长基团浓度的影响较大。     

微波等离子体化学气相沉积法生长非晶碳化硅薄膜

利用SiH4(80%Ar稀释)和CH4作为源气体,通过改变源气体流量比、基片温度、沉积气压等参量,使用微波电子回旋共振化学气相沉积法生长非晶碳化硅薄膜。实验结果表明碳化硅薄膜沉积速率随气体流量比R(CH4/(CH4+SiH4))的增加而减小、随基片温度的升高明显减小、随沉积气压的增加先增大后减小。红外结构表明:在较低流量比R下,薄膜主要由硅团簇和非晶碳化硅两相组成,而当R>0.5时,薄膜的结构主要由非晶碳化硅组成,薄膜中键合的H主要是Si和C的封端原子。同时,沉积温度的升高使碳化硅薄膜中Si-H,C-C和C-H键的含量减少,而薄膜中Si-C含量明显增加且峰位发生了红移。薄膜相结构的转变是薄膜光学带隙变化的原因。     

MPCVD法在Si衬底上生成β—C3N4晶态薄膜的研究

以Ｎ２,ＣＨ４作为反应气体,采用微波等离子体化学气相沉积法（ＭＰＣＶＤ）进行碳氮膜的合成研究。通过控制反应温度、气体流量、微波功率、反应气压,在Ｓｉ（１１１）和Ｓｉ（１００）基底上气相合成β－Ｃ３Ｎ４晶态薄膜。扫描电子显微镜（ＳＥＲＭ）下观察到生长在Ｓｉ基底上的薄膜具有六角晶棒的密结构。ＥＤＸ分析胡沉积条件的不同,六角晶棒中Ｎ／Ｃ在１．０～２．０之间。Ｘ射线衍射分析（ＸＲＤ）发现薄膜中含有β－Ｃ３     

PECVD法低温制备二氧化硅薄膜(英文)

针对金属层间介质以及MEMS等对氧化硅薄膜的需求,介绍了采用等离子增强型化学气相沉积(PECVD)技术,以SiH4和N2O为反应气体,低温制备SiO2薄膜的方法.利用椭偏仪和应力测试系统对制得的SiO2薄膜的厚度、折射率、均匀性以及应力等性能指标进行了测试,探讨了射频功率、反应腔室压力、气体流量比等关键工艺参数对SiO2薄膜性能的影响.结果表明:SiO2薄膜的折射率主要由N2O/SiH4的流量比决定,而薄膜均匀性主要受电极间距以及反应腔室压力的影响.通过优化工艺参数,在低温260℃下制备了折射率为1.45～1.52、均匀性为±0.64%、应力在-350～-16MPa可控的SiO2薄膜.采用该方法制备的SiO2薄膜均匀性好、结构致密、沉积速率快、沉积温度低且应力可控,可广泛应用于集成电路以及MEMS器件中.     

电化学制备有序聚苯胺／聚苯乙烯复合材料

利用垂直沉积自组装技术在氧化铟锡（ITO）导电玻璃基底上制备出高度有序的聚苯乙烯（PS）薄膜,以此为模板,在三电极体系中应用循环伏安法,控制电势在-0．3-0．9V之间,以20mV／S的扫描速度,在有序排列PS薄膜的表面电化学沉积聚苯胺（PANI）,成功制备出了聚苯胺／聚苯乙烯（PS／PANI）有序导电高分子复合材料,通过紫外-可见光分光光度计、循环伏安法、场发射扫描电镜、x射线衍射仪进行表征,结果表明,制得的PS／PANI复合材料粒径均匀、排列有序、呈密堆积结构,可为制备具有有序中空或大孔膜产物提供较理想的模板。     

ECR-CVD制备氟化非晶碳低k介质薄膜

采用电子回旋共振等离子体化学气相沉积(ECR-CVD)方法,以C4F8和CH4为源气体在不同气体流量比R(R=[CH4]/{[CH4] [C4F8]})条件下成功地沉积了氟化非晶碳(a-C:F)低介电常数(低k)材料.采用X光电子能谱和椭圆光谱方法分析了a-C:F薄膜的化学组分和光学性质.沉积的a-C:F薄膜介电常数约为2.1～2.4,热稳定性优于350℃.随着气体流量比的增大,沉积a-C:F薄膜中的碳含量增大,CF、CF2、CF3含量减少,C-C交链成分增加,从而使得π-π(*)吸收增强,并引起薄膜光学带隙下降.氮气气氛下350℃温度退火后应力释放引起a-C:F薄膜厚度变化,变化量小于4%.450℃温度退火后,由于热分解作用薄膜厚度变化量在30%左右.     

新型铅离子选择电极的制备及应用

本文研究了以二（苯并[d]噻唑-2-硫基）甲烷为载体的新型的PVC膜铅离子选择电极的响应行为。室温下,所制得的电极对Ph2＋在1．0×10-3-1．0×10—2mol／L浓度范围内呈现能斯特响应,响应斜率为30．2mV／decade,检测下限为9．0×10-6mol／L。该膜电极响应较快,响应时间在1ls以内可连续使用两个月。电极具有良好的稳定性和重现性。在优化条件下,电极对Pb：‘具有较好的选择性。该电极可在≤20％（V／V）的甲醇水溶液中使用。制备的铅离子选择电极可作为准确滴定铅离子的电位滴定指示电极,并能用于膨化食品及汽车驶过的土中铅含量的直接测定,结果令人满意。     

PCVD法对碳化硅陶瓷的表面改性研究

利用等离子辉光放电化学气相沉积技术（ＰＣＶＤ），控制甲烷与磋烷质量流量比、硅烷与氨质量流量比，在碳化硅基体表面分别沉积上无定形碳化硅和氨化硅薄膜，研究其膜的组成、沉积工艺、厚度等对碳化硅陶瓷的强度改性影响．在一定的沉积条件下沉积的碳化硅薄膜可以使基体强度提高２０％达到８５０ＭＰａ，沉积氮化硅薄膜使强度提高３０％达到９００ＭＰａ，改性的效果很明显．     

功率和温度对a-C:F:H膜表面形貌和结构的影响

分析薄膜的表面形貌对其生长机理和光学性质研究有着十分重要的作用。本文使用CF4和CH4为源气体，利用射频等离子体增强化学气相沉积（RF—PECVD）法在不同射频功率和沉积温度下制备了掺氟氢化无定形碳（a—C：F：H）薄膜，并在N2气氛中进行了不同温度的退火处理。用原子力显微镜（AFM）和扫描电子显微镜（SEM）观察了薄膜表面形貌，发现低功率下沉积的薄膜表面均匀性好、缺陷少；在低温下沉积的薄膜表面光滑，而高温下粗糙；真空低温退火可使薄膜表面形貌得到改善，但薄膜内空洞增加，退火温度过高，薄膜的结构发生变化，且在薄膜表面发生皲裂现象。用Raman光谱对薄膜内的结构变化进行了进一步的分析。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...