Removal of nickel from aqueous solutions by sawdust

The main parameters influencing Nickel (II) metal sorption on maple sawdust were: initial metal ion concentration, amount of adsorbent, and pH value of solution. The maximum percent metal removal was attained after about 1h. The greatest increase in the rate of adsorption of metal ions on sawdust was observed for pH changes from 2 to 5. An empirical relationship has been obtained to predict the percentage Nickel (II) removal at any time for known values of sorbent and initial sorbate concentration. The experimental results provided evidence for chelation ion exchange as the major adsorption mechanisms for binding metal ions to the sawdust. The adsorbent can be effectively regenerated using 0.1 M strong acid and reused.     

Removal of nickel(II) ions from aqueous solution using crab shell particles in a packed bed up-flow column

This paper investigates the ability of crab shell to remove nickel(II) ions from aqueous solution in a packed bed up-flow column with an internal diameter of 2 cm. The experiments were performed with different bed heights (15-25 cm) and using different flow rates (5-20 ml/min) in order to obtain experimental breakthrough curves. The bed depth service time (BDST) model was used to analyze the experimental data and the model parameters were evaluated. The column regeneration studies were carried out for seven sorption-desorption cycles. The elutant used for the regeneration of the sorbent was 0.01 M EDTA (disodium) solution at pH 9.8 adjusted using NH4OH. Due to continuous usage of crab shell, a performance loss was observed as the breakthrough curves become more flattened also indicated by the broadened mass transfer zone. The breakthrough time decreased uniformly from 28.1 to 9.5 h as the cycles progressed from one to seven, whereas nickel uptake remained approximately constant throughout the seven cycles. The life-factors for crab shell in terms of critical bed length and breakthrough time were found to be 1.1 cm/cycle and 0.17 per cycle, respectively. The elution efficiency was greater than 99.1% in all the seven cycles. The pH profiles during both sorption and desorption process were also reported. In sorption cycles, there was a sudden raise in pH in the early part of the process and then the pH decreased as the time progressed. In desorption cycles, pH decreased in initial stages and followed by gradual increase in pH, which eventually reached the pH of the inlet elutant.     

Effective removal of zinc ions from aqueous solutions using crab carapace biosorbent

The carapace of the crab (Cancer pagurus), a waste material disposed of by the seafood industry, has recently been shown to have potential as a biosorbent for the removal of metals from aqueous media. Crab carapace in the particle size ranges 0.25-0.8mm and 0.8-1.5mm were used to investigate the effects of agitation speed, contact time, metal concentration and initial pH on the removal of Zn(2+). In sequential-batch process Zn(2+) uptakes of 105.6 and 67.6 mg/g were recorded for 0.25-0.8 mm and 0.8-1.5 mm particles, respectively, while values of 141.3 and 76.9 mg/g were recorded in fixed-bed column studies. Binary-metal studies showed that the presence of Cu(2+) or Pb(2+) significantly suppressed Zn(2+) uptake. This study confirms that crab carapace may be considered a viable and cost-effective alternative to commercial activated carbon or ion-exchange resins for the removal of metals from aqueous media.     

Biosorption of Hg from aqueous solutions by crab carapace

Carapace from the edible crab was assessed for the biosorption of Hg from aqueous solutions. Batch adsorption studies were used to determine the effects of contact time, pH, concentration, particle size and Cu(II) as a co-ion. The removal of Hg was fast and efficient, attaining >80.0% from 500 mg/L by 60 min. Specific uptake increased from 0.1 to 13.0mg/g as initial concentration increased from 0.5 to 1000 mg/L while the removal efficiency decreased from 100.0% over the 0.5-10.0mg/L range to 65.0% at 1000 mg/L. As particle size decreases from >2.5 to <0.15 mm, the Hg uptake increased from 1.4 to 8.3mg/g. In binary metal solutions, Cu(II) reduced the Hg removal by 80.0% while the presence of Hg increased Cu(II) removal by approximately 7.0%. Crab carapace is a readily available alkaline waste and easily processed into durable granular forms. Therefore, it offers potential as a low-cost alternative to commercial adsorbents or as a complimentary polishing process for the removal of Hg from acidic solutions.     

Removal of heavy metal ions from aqueous solutions using various low-cost adsorbents

The removal of single heavy metals Co and Zn from aqueous solutions using various low-cost adsorbents (Fe(2)O(3), Fe(3)O(4), FeS, steel wool, Mg pellets, Cu pellets, Zn pellets, Al pellets, Fe pellets, coal, and GAC) was investigated. Experiments were performed at different solution pH values (1.5-9) and metal concentrations (0.67-333 mg/l). The effect of solution pH on metal adsorption using Fe(2)O(3) and Fe(3)O(4) was significant, but was negligibly small using steel wool, Mg pellets, Fe pellets, and Al pellets over the entire pH range. Steel wool and Mg pellets were the most excellent adsorbents; for example, the removal of Zn and Co from dilute solutions (<35 mg/l) was greater than 94% at an adsorbent dose of 1.7 g/l. A mass transfer model, which involves two parameters tau (50% breakthrough time) and k (proportionality constant), was proposed to describe breakthrough data of Co in the fixed beds packed with steel wool and Mg pellets. The calculated breakthrough curves agreed well with the measured data (standard deviation < 6%). The value of tau decreased with increasing the flow rate. The effects of flow rates on the value of k and adsorption capacity are discussed.     

Removal of cadmium from aqueous solutions by palygorskite

The sorption characteristics of palygorskite with respect to cadmium were studied with the aim of assessing its use in water purification systems. Using a batch method the influence of time (0.5-48 h), initial Cd concentration (5-150 mg/l or 0.044-1.34 mmol/l), ionic strength ([Ca(II)]: 0-0.1 mol/l), pH (3-7) and mineral dose (1-20 g/l) on Cd removal was evaluated. The sorption of Cd on palygorskite appeared as a fast process, with equilibrium being attained within the first half an hour of interaction. This process could be described by the Langmuir model and gave a maximum Cd sorption of 4.54 mg/g. This sorption capacity value was greatly affected by both pH and ionic strength. Thus, Cd sorption decreased as initial pH lessened, especially at proton concentrations similar to those of Cd, at which competition for variable charge sites (silanol groups on palygorskite surface) appeared to be important. High competing electrolyte concentrations also decreased significantly (close to 60%) the amount of sorbed Cd, suggesting a great contribution of replacement of exchange cations in this metal removal by palygorskite. The increase of mineral dose provoked a Cd removal raise; removal values in the range 85-45% were attained for Cd initial concentrations of 10-150 mg/l (0.089-1.34 mmol/l) when a palygorskite dose of 20 g/l was employed. Column studies were also performed in order to estimate the potential of palygorskite to be used in continuous flow purification systems, showing the effectiveness of this mineral to purify down to the legal limit of waste moderate volumes of Cd-containing solutions with a similar concentration (50mg/l or 0.445 mmol/l) to those mostly found in the upper range of concentrations usually present in industrial wastewaters.     

Removal of phosphate from aqueous solutions by electro-coagulation

The aim of this paper was to investigate the feasibility of the removal of phosphate from aqueous solution by electro-coagulation (EC). The current density (CD) between 2.5 and 10 mA cm(-2) and duration in the limits of 5-20 min were tried for different concentrations. In order to determine optimal operating conditions, the EC process used for the phosphate removal was examined in dependence with the CD, initial concentrations and time. The results of the experimental batch processing showed high effectiveness of the EC method in removing phosphate from aqueous solutions.     

Investigations of nickel(II) removal from aqueous solutions using tea factory waste

This paper presents the data for the effect of adsorbent dose, initial metal concentration, solution pH, agitating rate and temperature on the adsorption of nickel(II) on waste tea. Batch adsorption studies have been carried out. The equilibrium nature of nickel(II) adsorption at different temperature (25-60 degrees C) has been described by the Freundlich and Langmuir isotherm. The adsorption capacity (Q(0)) calculated from Langmuir isotherm was 15.26 mg Ni(II) g(-1) at initial pH of 4.0 at 25 degrees C. The results of the thermodynamic investigations indicate that the adsorption reactions are spontaneous (DeltaG degrees <0), slightly endothermic (DeltaH degrees > 0) and irreversible (DeltaS degrees > 0).     

Removal of tiemonium methylsulfate,from aqueous solutions using activated carbon prepared from date stones

The retention of a pharmaceutical compound, tiemonium methylsulfate (TIM), from aqueous solutions by adsorption onto activated carbon prepared from date stones (AC–DS) was investigated. Physical and chemical characteristics of this material were also determined. Results showed that pH 8 was optimal for TIM adsorption. Among the kinetic models considered, the pseudo-second-order model was the most appropriate to describe experimental data. Regarding adsorption isotherms, it was shown that the Sips model accurately describe the sorption of TIM onto AC–DS with a correlation factor R²?>?0.98. The adsorption capacity of AC–DS was found to be 42.2?mg?g^?1 at 10°C and 60.5?mg?g^?1 at 25°C, confirming its efficiency for the removal of this compound from aqueous solutions. The values of ΔG⁰ and ΔH⁰ confirmed that the adsorption of TIM onto AC–DS was spontaneous and endothermic in nature and hence more effective at high temperatures. An irregular increase in the randomness was suggested at the AC–DS solution interface during the adsorption process for positive values of ΔS⁰.     

Removal of lead from aqueous solutions using an immobilized biomaterial derived from a plant biomass

Because of the severity of heavy metal contamination and potential adverse health impact on the public, a tremendous effort has taken place to purify waters containing toxic metal ions. Traditional methods which have been employed prove to be costly and prohibitive for low level waste remediation. Biosorption is presented as an alternative to traditional physicochemical means for removing toxic metals from ground and wastewaters. Most recently, plant based biomaterials have been of interest. The bark of Hemidesmus indicus, an extensively available plant biomass commonly called as Indian sarsaparilla was used as biomaterial for removal of lead from aqueous streams. Batch experiments were carried out with immobilized biomass of H. indicus (IPBFIX) to optimize the experimental parameters like effect of contact time, initial metal concentration, initial IPBFIX concentration and co-metal ion effect on biosorption of lead from contaminated waters. Column experiments were performed under flow conditions for regeneration and recycle efficiency of IPBFIX and was found to be effective for three cycles. Elution experiments were carried out to remove lead ions from loaded IPBFIX and 100% elution was achieved with a 0.1M HNO(3) solution. The effectiveness of the IPBFIX for biosorption of lead ions was demonstrated using the wastewater samples emanating from a non-ferrous metal industry and the results are presented in this paper. The results from these studies will be useful for a novel phytofiltration technology to remove and recover lead from wastewaters and this can also be well adapted for secondary treatment or polishing of wastewaters. An attempt has been made to remove lead from the lead polluted waters (both ground and surface) from an industrially contaminated sites.     

Removal of cadmium from aqueous solutions using clinoptilolite: influence of pretreatment and regeneration

In this study, Cd removal from aqueous solutions via clinoptilolite was investigated in terms of the effect of pretreatment and regeneration. Four different chemicals (NaCl, KCl, CaCl₂ and HCl) were tested for this purpose. Samples treated by a total of 20 bed volume (BV) of 1 M NaCl solution prepared in tap water with no pH adjustment were found to perform satisfactorily. Five exhaustion and regeneration cycles were then carried out, revealing an increasing Cd removal capacity, coupled with constant Cd elution efficiency in progressing cycles. Furthermore, the change of pH and the presence of exchangeable (Na, K, Ca and Mg) and framework cations (Si and Al) in the aqueous phase were investigated. Subsequently, these were discussed in terms of progressive conversion of clinoptilolite to its homoionic Na-form, and the presence of different Cd removal mechanisms in the system. This study emphasizes the potential of clinoptilolite to be a part of sustainable wastewater treatment technologies, enabling the recovery of both the sorbent and the metal, via demonstration of effective Cd removal and clinoptilolite recovery, besides successful concentration of metal in the regenerant solution.     

Removal of lead from aqueous solutions by activated phosphate

The potential of using activated phosphate as a new adsorbent for the removal of Pb from aqueous solutions was investigated. The kinetic of lead adsorption and the adsorption process were compared for natural phosphate (NP) and activated phosphate (AP). The results indicate that equilibrium was established in about 1h for NP and 3 h for AP. The effect of the pH was examined in the range 2-6. The maximum removal obtained is between two and three for NP and between three and four for AP. The maximum adsorption capacities at 25 degrees C are 155.04 and 115.34 mg/g for AP and NP, respectively. The effect of temperature has been carried out at 25, 35 and 45 degrees C. The data obtained from adsorption isotherms of lead at different temperatures fit to linear form of Langmuir adsorption equation. The thermodynamic parameters such as enthalpy (DeltaH), free energy (DeltaG) and entropy (DeltaS) were calculated. They show that adsorption of lead on NP and AP is an endothermic process more effective at high temperatures. These results show that AP is a good adsorbent for heavy metals from aqueous solutions and could be used as a purifier for water and wastewater.     

Removal of ammonium from aqueous solutions with volcanic tuff

This paper presents kinetic and equilibrium data concerning ammonium ion uptake from aqueous solutions using Romanian volcanic tuff. The influence of contact time, pH, ammonium concentration, presence of other cations and anion species is discussed. Equilibrium isotherms adequately fit the Langmuir and Freundlich models. The results showed a contact time of 3h to be sufficient to reach equilibrium and pH of 7 to be the optimum value. Adsorption capacities of 19 mg NH(4)(+)/g were obtained in multicomponent solutions (containing NH(4)(+), Zn(2+), Cd(2+), Ca(2+), Na(2+)). The presence of Zn and Cd at low concentrations did not decrease the ammonium adsorption capacity. Comparison of Romanian volcanic tuff with synthetic zeolites used for ammonium removal (5A, 13X and ZSM-5) was carried out. The removal efficiciency of ammonium by volcanic tuff were similar to those of zeolites 5A and 13X at low initial ammonium concentration, and much higher than those of zeolite ZSM-5.     

竹活性炭负载二氧化钛光催化降解水溶液中甲醛的研究

采用竹活性炭作为载体,通过溶胶-凝胶法制备二氧化钛/竹活性炭复合光催化剂,并考察其对水溶液中甲醛的去除效果.分别考察了预吸附时间、催化剂投加量、初始反应浓度等对去除效果的影响,结果表明预吸附1h,催化剂投加量为1g时,初始浓度为5mg/L甲醛溶液在17W紫外灯照射480min时,去除率达95.96%.同时,对制备所得的...     

Removal of Cr(VI) from aqueous solutions using modified red pine sawdust

The adsorption of Cr(VI) from aqueous solutions on sawdust (SD), base extracted sawdust (BESD) and tartaric acid modified sawdust (TASD) of Turkish red pine tree (Pinus nigra), a timber industry waste, was studied at varying Cr(VI) concentrations, adsorbent dose, modifier concentration and pH. Batch adsorption studies have been carried out. Sawdust was collected from waste timber industry and modified with various amount of tartaric acid (TA) (0.1-1.5M). The batch sorption kinetics has been tested and the applicability of the Langmuir and Freundlich adsorption isotherms for the present system has been tested at 25+/-2 degrees C. Under observed test conditions, the equilibrium adsorption data fits the linear Freundlich isotherms. An initial pH of 3.0 was most favorable for Cr(VI) removal by all adsorbents. Maximum Cr(VI) was sequestered from the solution within 120 min after the beginning for every experiment. The experimental result inferred that chelation and ion exchange is one of the major adsorption mechanisms for binding metal ions to the SD. Percentage removal of Cr(VI) was maximum at the initial pH of 3.0 (87.7, 70.6 and 55.2% by TASD, BESD, and SD, respectively). Adsorption capacities range from 8.3 to 22.6 mg/g for SD samples.     

Removal of heavy metal ions from aqueous solutions using carbon aerogel as an adsorbent

The removal of Cd(II), Pb(II), Hg(II), Cu(II), Ni(II), Mn(II) and Zn(II) by carbon aerogel has been found to be concentration, pH, contact time, adsorbent dose and temperature dependent. The adsorption parameters were determined using both Langmuir and Freundlich isotherm models. Surface complexation and ion exchange are the major removal mechanisms involved. The adsorption isotherm studies clearly indicated that the adsorptive behaviour of metal ions on carbon aerogel satisfies not only the Langmuir assumptions but also the Freundlich assumptions, i.e. multilayer formation on the surface of the adsorbent with an exponential distribution of site energy. The applicability of the Lagergren kinetic model has also been investigated. Thermodynamic constant (K(ad)), standard free energy (DeltaG(0)), enthalpy (DeltaH(0)) and entropy (DeltaS(0)) were calculated for predicting the nature of adsorption. The results indicate the potential application of this method for effluent treatment in industries and also provide strong evidence to support the adsorption mechanism proposed.     

Removal of Cr(VI) from aqueous solutions using agricultural waste 'maize bran'

Novel biosorbent 'maize bran' has been successfully utilized for the removal of Cr(VI) from aqueous solution. The effect of different parameters such as contact time, sorbate concentration, pH of the medium and temperature were investigated and maximum uptake of Cr(VI) was 312.52 (mgg(-1)) at pH 2.0, initial Cr(VI) concentration of 200mgL(-1) and temperature of 40 degrees C. Effect of pH showed that maize bran was not only removing Cr(VI) from aqueous solution but also reducing toxic Cr(VI) into less toxic Cr(III). The sorption kinetics was tested with first order reversible, pseudo-first order and pseudo-second order reaction and it was found that Cr(VI) uptake process followed the pseudo-second order rate expression. Mass transfer of Cr(VI) from bulk to the solid phase (maize bran) was studied at different temperatures. Different thermodynamic parameters, viz., DeltaG degrees , DeltaH degrees and DeltaS degrees have also been evaluated and it has been found that the sorption was feasible, spontaneous and endothermic in nature. The Langmuir and Freundlich equations for describing sorption equilibrium were applied and it was found that the process was well described by Langmuir isotherm. Desorption studies was also carried out and found that complete desorption of Cr(VI) took place at pH of 9.5.     

Removal of nickel from aqueous solution by the bacterium Bacillus thuringiensis

The biosorption of the toxic metal (nickel) from aqueous solutions on dried vegetative cell and spore-crystal mixture of Bacillus thuringiensis var. thuringiensis was tested under laboratory conditions as a function of pH, initial metal ion concentration and temperature. The characteristics of the adsorption process were investigated using Scatchard analysis. Scatchard analysis of the equilibrium binding data for metal ions on vegetative cell and spore-crystal mixture of B. thuringiensis gave rise to a linear plot, indicating that the Langmuir model could be applied successfully. Adsorption behaviour of nickel(II) ion on B. thuringiensis is expressed by both Langmuir and Freundlich isotherms. The adsorption data with respect to the metal provided an excellent fit to both isotherms. Ni(II) ion uptake of B. thuringiensis's spore-crystal mixture at 250 mg l(-1) was 15.7%, whereas its vegetative cell metal uptake was 10%. The best temperature for ion uptake was found to be at 35 degrees C.     

Removal of phosphate from aqueous solutions and sewage using natural and surface modified coir pith

Iron impregnated coir pith (CP-Fe-I) can be effectively used for the removal of phosphate from aqueous streams and sewage. Iron impregnation on natural coir pith was carried out by drop by drop addition method. The effect of various factors such as pH, initial concentration of phosphate, contact time and adsorbent dose on phosphate adsorption was studied by batch technique. The pH at 3.0 favored the maximum adsorption of phosphate from aqueous solutions. The effect of pH on phosphate adsorption was explained by pH(zpc), phosphate speciation in solution and affinity of anions towards the adsorbent sites. A comparative study of the adsorption of phosphate using CP-Fe-I and CP (coir pith) was made and results show that the former one is five to six times more effective than the latter. Kinetic studies revealed that the adsorption process followed a pseudo-second order kinetic model. Adsorption followed Langmuir isotherm model. Column studies were conducted to examine the utility of the investigated adsorbent for the removal of phosphate from continuously flowing aqueous solutions.     

Removal of boron from aqueous solutions by batch adsorption on calcined alunite using experimental design

In the present paper, boron removal from aqueous solutions by batch adsorption was investigated and 2(3) full factorial design was applied. Calcined alunite was used as adsorbent. In the study, three parameters affected the performance and two levels of these parameters were investigated. The chosen parameters were temperature (25 and 45 degrees C, respectively), pH (3 and 10) and mass of adsorbent (0.5 g adsorbent per 25 mL solution and 1g adsorbent per 25 mL solution). The significance of the effects was checked by analysis of variance (statistical software, MINITAB-Version 15). The model-function equation for boron adsorption on calcined alunite was obtained. The results showed that temperature, pH and mass of adsorbent affected boron removal by adsorption. Boron removal increased with increasing pH and adsorbent dosage, but decreased with increasing temperature. The optimum conditions were found as pH 10, adsorbent dosage=1g of calcined alunite per 25 mL solution and temperature=25 degrees C by using factorial design. In addition, the effects of parameters such as calcination temperature, pH, temperature, adsorbent dosage and initial boron concentration on boron removal were investigated. The adsorption isotherm studies were also performed. Maximum adsorbent capacity (q(0)) was calculated as 3.39 mg/g. Thermodynamic parameters such as change in free energy (DeltaG degrees), enthalpy (DeltaH degrees) and entropy (DeltaS degrees) were also determined.