Photoluminescence of phosphorous doped Ge on Si (100)

Photoluminescence (PL) of selectively grown phosphorus (P) doped germanium (Ge) is investigated. 350–600 nm thick P-doped Ge is grown on 100 nm thick P-doped Ge buffer layer, which is annealed at 800 °C before the main part of Ge deposition. In the case of Ge deposited at 325 °C, approximately two times higher PL intensity is observed by P doping of ~3.2×10¹⁹ cm⁻³. Further increase of PL intensity by a factor of 1.5 is observed by increasing the growth temperature from 325 °C to 400 °C due to improved crystal quality. Varying PH₃ partial pressure at 400 °C, red shift of the PL occurred with increasing P concentration due to higher bandgap narrowing. With increasing P concentration up to ~1.4×10¹⁹ cm⁻³ at 400 °C the PL peak intensity increases by filling electrons into the L valley and decreases due to enhanced point defect concentration and degraded crystallinity. By post-annealing at 500–800 °C, the PL intensity is further increased by a factor of 2.5 because of increased active P concentration and improved crystal quality. Reduced direct bandgap energy by introducing tensile strain is also observed.     

Evaporated iron disulfide thin films with sulfurated annealing treatments

FeS₂ thin films were grown on a glass substrate using a physical vapor deposition technique at room temperature. Subsequently, the thin films were annealed in two different atmospheres: vacuum and vacuum-sulfur. In the vacuum-sulfur atmosphere a graphite box was used as sulfur container and the films were sulfurated successfully at 200–350 ºC. It was found that annealing in a vacuum-sulfur atmosphere was indispensable in order to obtain polycrystalline FeS₂ thin films. The polycrystalline nature and pure phase were determined by XRD and Raman techniques and the electrical properties by the Hall effect. Using the sulfurating technique, the n-type semiconductor was prepared at 200–350 °C and a p-type at 500 °C. The carrier concentrations were between 1.19×10²⁰ and 2.1×10²⁰ cm⁻³. The mobility was 9.96–5.25 cm² V⁻¹ s⁻¹ and the resistivity was 6.31×10⁻² to 1.089×10⁻² Ω cm. The results obtained from EDS showed that the films prepared in the vacuum-sulfur atmosphere were close to stoichiometric and that the indirect band gap varied between 1.03 and 0.945 eV.     

Dependence of the optoelectronic properties of selenium-hyperdoped silicon on the annealing temperature

Selenium-hyperdoped silicon was prepared by ion implantation at 100 eV to a dose of 6×10¹⁵ Se/cm², followed by furnace annealing at 500–900 °C for 30 min. A phase transition from amorphous to crystalline was observed for the sample annealed at 600 °C. Carrier density in the Se doping layer gradually increases with the annealing temperature and a high carrier/donor ratio of 7.5% was obtained at 900 °C. The effects of annealing temperature on the rectifying behavior and external quantum efficiency of n⁺p junctions formed on Se-hyperdoped silicon were also investigated. We found that 700 °C was the optimal annealing temperature for improving the crystallinity, below-bandgap absorption, junction rectification and external quantum efficiency of Se-doped samples.     

Investigations on the annealing behavior of high-energy carbon irradiated Au/n-GaAs Schottky barrier diodes

Au Schottky barrier diodes (SBDs) have been irradiated using high-energy carbon ion fluences of 1×10¹¹, 1×10¹² and 1×10¹³ cm⁻². Current–voltage characteristics of unirradiated and irradiated diodes have been analyzed. The change in reverse leakage current increases with increasing ion fluence due to the irradiation-induced defects at the interface. The diodes were annealed at 523 and 623 K to study the effect of annealing. The rectifying behavior of the irradiated SBDs improves at 523 K. But at 623 K, the diode behavior deteriorates irrespective of the fluences. Better enhancement in the barrier height and also improvement in the ideality factor of the diodes has been observed at the annealing temperature of 523 K. Scanning Electron Microscopic analysis was carried out on the irradiated samples to delineate the projected range of the defects by high-energy carbon ion irradiation.     

Effects of RTA temperatures on conductivity and micro-structures of boron-doped silicon nanocrystals in Si-rich oxide thin films

In this work, the B-doped Si rich oxide (SRO) thin films were deposited and then annealed using rapid thermal annealing (RTA) to form SiO₂-matrix silicon nanocrystals (Si NCs). The effects of the RTA temperatures on the structural properties, conduction mechanisms and electrical properties of B-doped SRO thin films (BSF) were investigated systematically using Hall measurements, Fourier transform infrared spectroscopy and Raman spectroscopy. Results showed that the crystalline fraction of annealed BSF increased from 41.3% to 62.8%, the conductivity was increased from 4.48×10⁻³ S/cm to 0.16 s/cm, the carrier concentration was increased from 8.74×10¹⁷ cm⁻³ to 4.9×10¹⁸ cm⁻³ and the carrier mobility was increased from 0.032 cm² V⁻¹ s⁻¹ to 0.2 cm² V⁻¹ s⁻¹ when the RTA temperatures increased from 1050 °C to 1150 °C. In addition, the fluctuation induced tunneling (FIT) theory was applicable to the conduction mechanisms of SiO₂-matrix boron-doped Si-NC thin films.     

Ultraviolet-assisted annealing for low-temperature solution-processed p-type gallium tin oxide (GTO) transparent semiconductor thin films

Solution-processed p-type gallium tin oxide (GTO) transparent semiconductor thin films were prepared at a low temperature of 300 °C using ultraviolet (UV)-assisted annealing instead of conventional high-temperature annealing (> 500 °C). We report the effects of UV irradiation time on the structural, optical, and electrical properties of sol-gel derived GTO thin films and a comparison study of the physical properties of UV-assisted annealed (UVA) and conventional thermally annealed (CTA) GTO thin films. The Ga doping content was fixed at 15 at% in the precursor solution ([Ga]/[Sn]+[Ga] = 15%). After a spin-coating and preheating procedure was performed two times, the dried sol-gel films were heated on a hotplate at 300 °C under UV light irradiation for 1–4 h. Each UVA GTO thin film had a dense microstructure and flat free surface and exhibited an average optical transmittance approaching 85.0%. The level of crystallinity, crystallite size, and hole concentration density of the GTO thin films increased with increasing UV irradiation time. In this study, the UVA 4 h thin film samples exhibited the highest hole concentration (9.87 × 10¹⁷ cm⁻³) and the lowest resistivity (1.8 Ω cm) and had a hole mobility of 5.1 cm²/Vs.     

Influence of thermal annealing on electrical and optical properties of indium tin oxide thin films

Transparent conducting indium tin oxide (ITO) thin films with the thickness of 300 nm were deposited on quartz substrates via electron beam evaporation, and five of them post-annealed in air atmosphere for 10 min at five selected temperature points from 200 °C to 600 °C, respectively. An UV–vis spectrophotometer and Hall measurement system were adopted to characterize the ITO thin films. Influence of thermal annealing in air atmosphere on electrical and optical properties was investigated in detail. The sheet resistance reached the minimum of 6.67 Ω/sq after annealed at 300 °C. It increased dramatically at even higher annealing temperature. The mean transmittance over the range from 400 nm to 800 nm reached the maximum of 89.03% after annealed at 400 °C, and the figure of merit reached the maximum of 17.79 (Unit: 10⁻³ Ω⁻¹) under the same annealing condition. With the annealing temperature increased from 400 °C to 600 °C, the variations of transmittance were negligible, but the figure of merit decreased significantly due to the deterioration of electrical conductivity. With increasing the annealing temperature, the absorption edge shifted towards longer wavelength. It could be explained on the basis of Burstein–Moss shift. The values of optical band gap varied in the range of 3.866–4.392 eV.     

Effects of annealing treatment on the high temperature performance of 4H-SiC metal-semiconductor-metal ultraviolet photodiodes

The high temperature performance plays a crucial role in the high-temperature harsh environment detection. In this paper, the electrical and optical characteristics of 4H-SiC metal-semiconductor-metal (MSM) ultraviolet photodiodes (PDs) were investigated at high temperatures. The C-V measurement indicates that the 4H-SiC Schottky barrier diode is partially depleted at 40 V bias. Analysis of I-V data based on the thermionic emission theory demonstrates that the annealing treatment at 400 °C can effectively improve the homogeneity of Ni/4H-SiC Schottky barrier height. Experimental results confirm that the annealing treatment is beneficial not only to reduce the dark current and improve the photoresponse, but also to enhance the sensitivity for 4H-SiC MSM PDs. The sensitivity of 400 °C annealed MSM PDs (6.2 × 10³) is five times larger than that of as-deposited MSM PDs (1.3 × 10³) at 200 °C.     

Sol–gel derived nanocrystalline TiO2 thin films: A promising candidate for self-cleaning smart window applications

In the present work, anatase TiO₂ films are prepared by sol–gel spin coating method. The structural and optical properties of the films have been studied at different post-annealing temperatures. The photocatalytic activity and electrochromic performance of the films are investigated. The films annealed at 400 °C exhibit the highest photocatalytic activity with a rate constant of 4.56×10⁻³ min⁻¹. The electrochromic performance for the films annealed at 400 °C expressed in terms of difference in optical density (ΔOD) at 550 nm between coloured and bleached state is 0.5493. This combination of photocatalysis and electrochromism makes the sol–gel derived titania thin films as promising candidates for self-cleaning smart window applications.     

Annealing effects on physical properties of doped CdTe thin films for photovoltaic applications

Polycrystalline Cadmium Telluride (CdTe) thin films were prepared on glass substrates by thermal evaporation at the chamber ambient temperature and then annealed for an hour in vacuum ~1×10⁻⁵ mbar at 400 °C. These annealed thin films were doped with copper (Cu) via ion exchange by immersing these films in Cu (NO₃)₂ solution (1 g/1000 ml) for 20 min. Further these films were again annealed at different temperatures for better diffusion of dopant species. The physical properties of an as doped sample and samples annealed at different temperatures after doping were determined by using energy dispersive x-ray analysis (EDX), x-ray diffraction (XRD), Raman spectroscopy, transmission spectra analysis, photoconductivity response and hot probe for conductivity type. The optical band gap of these thermally evaporated Cu doped CdTe thin films was determined from the transmission spectra and was found to be in the range 1.42–1.75 eV. The direct energy band gap was found annealing temperatures dependent. The absorption coefficient was >10⁴ cm⁻¹ for incident photons having energy greater than the band gap energy. Optical density was observed also dependent on postdoping annealing temperature. All samples were found having p-type conductivity. These films are strong potential candidates for photovoltaic applications like solar cells.     

High thermal annealing effect on structural and optical properties of ZnO–SiO2 nanocomposite

The effect of annealing temperature on photoluminescence (PL) of ZnO–SiO₂ nanocomposite was investigated. The ZnO–SiO₂ nanocomposite was annealed at different temperatures from 600 °C to 1000 °C with a step of 100 °C. High Resolution Transmission Electron Microscope (HR-TEM) pictures showed ZnO nanoparticles of 5 nm are capped with amorphous SiO₂ matrix. Field Emission Scanning Electron Microscope (FE-SEM) pictures showed that samples exhibit spherical morphology up to 800 °C and dumbbell morphology above 800 °C. The absorption spectrum of ZnO–SiO₂ nanocomposite suffers a blue-shift from 369 nm to 365 nm with increase of temperature from 800 °C to 1000 °C. The PL spectrum of ZnO–SiO₂ nanocomposite exhibited an UV emission positioned at 396 nm. The UV emission intensity increased as the temperature increased from 600 °C to 700 °C and then decreased for samples annealed at and above 800^°C. The XRD results showed that formation of willemite phase starts at 800 °C and pure willemite phase formed at 1000 °C. The decrease of the intensity of 396 nm emission peak at 900 °C and 1000 °C is due to the collapse of the ZnO hexagonal structure. This is due to the dominant diffusion of Zn into SiO₂ at these temperatures. At 1000 °C, an emission peak at 388 nm is observed in addition to UV emission of ZnO at 396 nm and is believed to be originated from the willemite.     

Low-temperature formation of self-assembled Ge quantum dots on Si(100) under high carbon mediation via solid-phase epitaxy

CMOS-compatible low-temperature formation of self-assembled Ge quantum dots (QDs) by carbon (C) mediation via a solid-phase epitaxy (SPE) has been demonstrated. The samples were prepared by a solid-source molecular beam epitaxy (MBE) system. C and Ge were successively deposited on Si(100) at 200 °C and Ge/C/Si heterostructure was annealed in the MBE chamber. Sparse Volmer-Weber mode Ge dots without a wetting layer were formed for C coverage (θ_C) of 0.25 and 0.5 ML by lowering SPE temperature (T_S) to 450 °C, but small and dense Stranski-Krastanov (SK)-mode Ge QDs with the wetting layer were obtained with increasing C coverage of 0.75 ML even at 450 °C. From the investigation of SPE temperature effect on Ge QD formation for θ_C of 0.75 ML, SK-mode Ge QDs of about 10 nm in diameter and of about 4.5×10¹¹ cm⁻² in density were formed at T_S≥400 °C. The wetting layer of SK-mode QDs was almost constant 0.2-nm thick at T_S≥450 °C. Measurements of chemical binding states of C in Ge QDs and at Ge/Si interface revealed that a large amount of C–Ge bonds were formed in the wetting layer for high C coverage, and the formation of C–Ge bonds, together with the formation of C–Si bonds, enabled the low-temperature formation of small and dense Ge QDs. These results suggest that the C-mediated solid-phase epitaxy is effective to form small and dense SK-mode QDs at low temperature.     

Investigation of structural and optoelectronic properties of annealed nickel phthalocyanine thin films

Thin films of nickel phthalocyanine (NiPc) were prepared by thermal evaporation and the effects of annealing temperature on the structural and optical properties of the samples were studied using different analytical methods. Structural analysis showed that the grain size and crystallinity of NiPc films improved as annealing temperature increased from 25 to 150 °C. Also, maximum grain size (71.3 nm) was obtained at 150 °C annealing temperature. In addition, NiPc films annealed at 150 °C had a very smooth surface with an RMS roughness of 0.41 nm. Optical analysis indicated that band gap energy of films at different annealing temperatures varied in the range of 3.22–3.28 eV. Schottky diode solar cells with a structure of ITO/PEDOT:PSS/NiPc/Al were fabricated. Measurement of the dark current density–voltage (J–V) characteristics of diodes showed that the current density of films annealed at 150 °C for a given bias was greater than that of other films. Furthermore, the films revealed the highest rectification ratio (23.1) and lowest barrier height (0.84 eV) demonstrating, respectively, 23% and 11% increase compared with those of the deposited NiPc films. Meanwhile, photoconversion behavior of films annealed at 150 °C under illumination showed the highest short circuit current density (0.070 mA/cm²) and open circuit voltage of (0.55 V).     

Effect of thermal annealing on the structural,morphological and super capacitor behavior of MnO2 nanocrystals

Precursors of nanosized manganese dioxide were prepared through a chemical precipitation method. The synthesized precursors of MnO₂ were subjected to thermo gravimetric analysis. The thermal analysis results showed the MnO₂ formation at 500 °C. To study the effect of thermal treatments on the capacitive behavior of MnO₂, the precursors were annealed at different temperatures (300, 400 and 500 °C). The annealed products were characterized by X-ray diffraction (XRD), Fourier transforms infra-red spectroscopy (FT-IR) and cyclic Voltammetry (CV) analysis. Among the annealed products, MnO₂ annealed at 400 °C exhibits high specific capacitance. The morphologies of the products annealed at 400 and 500 °C were analyzed by a scanning electron microscope (SEM) and atomic force microscopy (AFM). The sample annealed at 500 °C shows spherical morphology with the inclusion of nanorods. To confirm the morphology of the annealed products, field emission transmission electron microscope (FE-TEM) measurements were carried out.     

Defect modification in ZnInSnO transistor with solution-processed Al2O3 dielectric by annealing

The properties of solution-processed Al₂O₃ thin films annealed at different temperatures were thoroughly studied through thermogravimetry–differential thermal analysis, UV–vis-NIR spectrophotometer measurements, scanning electron microscopy, X-ray diffraction, atomic force microscopy and a series of electrical measurements. The solution-processed ZnInSnO thin films transistors (TFTs) with the prepared Al₂O₃ dielectric were annealed at different temperatures. The TFTs annealed at 600 °C have displayed excellent electrical performance such as the field-effect mobility of 116.9 cm² V⁻¹ s⁻¹ and a subthreshold slope of 93.3 mV/dec. The performance of TFT device could be controlled by adjusting the annealing temperature. The results of two-dimensional device simulations demonstrate that the improvement of device performance are closely related with the reduction of interface defects between channel and dielectric and subgap density of stats (DOS) in the channel layer.     

Interaction of ion-implantation-induced interstitials in B-doped SiGe

B-doped Si_0.77Ge_0.23 of various surface-doping levels was used to investigate the evolution of implant damage and the corresponding transient enhanced diffusion of boron as a function of boron concentration. These layers were implanted with a non-amorphizing 60 keV, 1×10¹⁴ cm⁻² Si, and annealed at 750 °C. Plan-view transmission electron microscopy (PTEM) confirmed the formation and dissolution of dislocation loops. Transient enhanced diffusion (TED) is evident in the surface doped SiGe, but the low diffusivity of interstitials in Si_0.77Ge_0.23 and the presence of interstitial traps inhibited TED at the deeper B marker layer.     

Contact resistivity of amorphous and crystalline GeCu2Te3 to W electrode for phase change random access memory

We have investigated the contact resistivity of GeCu₂Te₃ (GCT) phase change material to a W electrode using the circular transfer length method (CTLM). The contact resistivity ρ_c of as-deposited amorphous GCT to W was 3.9×10⁻² Ω cm². The value of ρ_c drastically decreased upon crystallization and crystalline GCT that annealed at 300 °C showed a ρ_c of 4.8×10⁻⁶ Ω cm². The ρ_c contrast between amorphous (as-deposited) and crystalline (annealed at 300 °C) states was larger in GCT than in conventional Ge₂Sb₂Te₅ (GST). Consequently, it was suggested from a calculation based on a simple vertical structure memory cell model that a GCT memory cell shows a four times larger resistance contrast than a GST memory cell.     

Structural and electrical characterization of CoNiO monolayer as copper diffusion barrier in integrated circuits

Diffusion barrier properties of CoNiO monolayer, deposited by Langmuir Blodgett (LB) technique, were studied against the diffusion of copper through SiO₂. Cu/CoNiO/SiO₂/Si and Cu/SiO₂/Si test structures were prepared and compared for this purpose. These test structures were annealed at temperatures starting from 100 °C up to 650 °C in vacuum. Samples were characterized using Energy Dispersive X-ray Spectroscopy (EDS), Atomic force microscopy (AFM), X-ray diffraction (XRD), scanning electron microscope (SEM), four probe resistivity measurement, Capacitance-Voltage (C‒V), Current-Voltage (I‒V) characterization techniques. EDS and AFM confirmed the composition and structure of the deposited monolayer. Thermal stability was studied using X-ray diffraction (XRD), Scanning Electron Microscope (SEM) and four probe techniques. Results indicated that structure with barrier was stable up to 600 °C whereas its counterpart could sustain only up to 300 °C. Sheet resistance of Cu/SiO₂/Si structure starts increasing at 300 °C and that of Cu/CoNiO/SiO₂/Si test structure was almost unchanged up to 600 °C in. SEM analysis of samples annealed at different temperatures also confirmed the XRD and four probe results. Biased Thermal Stress (BTS) was applied to the samples and its effect was observed using C‒V analysis. C‒V curves showed that in the presence of CoNiO barrier layer there was no shift in the C‒V curve even after 120 min of BTS while in the absence of barrier there was a significant shift in the C‒V curve even after 30 min of BTS. Leakage current density (j_L) was plotted against the BTS duration under same BTS conditions. It was found that the Cu/CoNiO/SiO₂/Si stack could survive about two times more than the Cu/SiO₂/Si stack.     

Characteristics of RF reactive sputter-deposited Pt/SiO2/n-InGaN MOS Schottky diodes

All RF sputtering-deposited Pt/SiO₂/n-type indium gallium nitride (n-InGaN) metal–oxide–semiconductor (MOS) diodes were investigated before and after annealing at 400 °C. By scanning electron microscopy (SEM), the thickness of Pt, SiO_2, n-InGaN layer was measured to be ~250, 70, and 800 nm, respectively. AFM results also show that the grains become a little bigger after annealing, the surface topography of the as-deposited film was smoother with the rms roughness of 1.67 nm and had the slight increase of 1.92 nm for annealed sample. Electrical properties of MOS diodes have been determined by using the current–voltage (I–V) and capacitance–voltage (C–V) measurements. The results showed that Schottky barrier height (SBH) increased slightly to 0.69 eV (I–V) and 0.82 eV (C–V) after annealing at 400 °C for 15 min in N₂ ambient, compared to that of 0.67 eV (I–V) and 0.79 eV (C–V) for the as-deposited sample. There was the considerable improvement in the leakage current, dropped from 6.5×10⁻⁷ A for the as-deposited to 1.4×10⁻⁷ A for the 400 °C-annealed one. The annealed MOS Schottky diode had shown the higher SBH, lower leakage current, smaller ideality factor (n), and denser microstructure. In addition to the SBH, n, and series resistance (R_s) determined by Cheungs׳ and Norde methods, other parameters for MOS diodes tested at room temperature were also calculated by C–V measurement.     

Effect of molybdenum electrode annealing on the interface properties between metal and pentacene

Contact resistance between molybdenum (Mo) electrode and pentacene was studied with transmission line method (TLM). The Mo electrodes were annealed at 200 °C, 400 °C, 600 °C and 800 °C for 1 h and pentacene layer of 300 Å thickness was vacuum deposited on patterned Mo to form Mo–pentacene contact. Current–voltage measurement for Mo–pentacene contact showed linear relationship and it was confirmed that ohmic contact was formed. XRD and AFM measurements showed that Mo could be crystallized at annealing temperatures above 600 °C. 800 °C annealed Mo showed larger grains and work function was increased from 4.60 eV to 4.80 eV due to the decrease in defect density. The contact resistance was reduced down to 11.2 MΩ cm from 37.8 MΩ cm of as-deposited Mo. Also the pentacene film deposited on annealed Mo was denser with better crystallinity. Bottom contact organic field-effect transistor made with 800 °C annealed Mo showed better performance than as deposited Mo.