Epoxidized natural rubber/epoxy blends: Phase morphology and thermomechanical properties

Epoxidized natural rubbers (ENRs) were prepared. ENRs with different concentrations of up to 20 wt % were used as modifiers for epoxy resin. The epoxy monomer was cured with nadic methyl anhydride as a hardener in the presence of N,N‐dimethyl benzyl amine as an accelerator. The addition of ENR to an anhydride hardener/epoxy monomer mixture gave rise to the formation of a phase‐separated structure consisting of rubber domains dispersed in the epoxy‐rich phase. The particle size increased with increasing ENR content. The phase separation was investigated by scanning electron microscopy and dynamic mechanical analysis. The viscoelastic behavior of the liquid‐rubber‐modified epoxy resin was also evaluated with dynamic mechanical analysis. The storage moduli, loss moduli, and tan δ values were determined for the blends of the epoxy resin with ENR. The effect of the addition of rubber on the glass‐transition temperature of the epoxy matrix was followed. The thermal stability of the ENR‐modified epoxy resin was studied with thermogravimetric analysis. Parameters such as the onset of degradation, maximum degradation temperature, and final degradation were not affected by the addition of ENR. The mechanical properties of the liquid‐natural‐rubber‐modified epoxy resin were measured in terms of the fracture toughness and impact strength. The maximum impact strength and fracture toughness were observed with 10 wt % ENR modified epoxy blends. Various toughening mechanisms responsible for the enhancement in toughness of the diglycidyl ether of the bisphenol A/ENR blends were investigated. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39906.     

Morphology of rubber‐modified vinyl ester resins cured at different temperatures

The morphologies of styrene (St) crosslinked divinylester resins (DVER) modified with elastomers were analyzed. The primary focus of this study was on the effect of the molecular weight of the resins, the reactivity of the elastomeric modifiers, and the temperature of curing. All of these variables have a strong influence on both the miscibility and the viscosity of the system, affecting the phase‐separation process that takes place in the unreacted and the reacting mixture. The selected liquid rubbers were carboxyl‐terminated poly(butadiene‐co‐acrylonitrile) (CTBN), a common toughening agent for epoxy resins, and an almost unreactive rubber with the DVER; and St comonomers and vinyl‐terminated poly(butadiene‐co‐acrylonitrile (VTBN), a reactive rubber. Different morphologies potentially appear in these systems: structures formed by DVER–St nodules surrounded by elastomer and spanning the whole sample; dual cocontinuous micron‐size domains formed by elastomer‐rich or resin‐rich domains; and a continuous DVER–St‐rich phase with included complex nodular domains. These microstructures can be varied by just changing the nature and concentration of the elastomer, the molecular weight of the resin, or the curing temperature. The appearance of these morphologies is discussed as a function of the above variables. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 274–283, 2003     

Enhanced fracture toughness of epoxy resins with novel amine‐terminated poly(arylene ether sulfone)–carboxylic‐terminated butadiene‐acrylonitrile–poly(arylene ether sulfone) triblock copolymers

Amine‐terminated poly(arylene ether sulfone)–carboxylic‐terminated butadiene‐acrylonitrile–poly(arylene ether sulfone) (PES‐CTBN‐PES) triblock copolymers with controlled molecular weights of 15,000 (15K) or 20,000 (20K) g/mol were synthesized from amine‐terminated PES oligomer and commercial CTBN rubber (CTBN 1300x13). The copolymers were utilized to modify a diglycidyl ether of bisphenol A epoxy resin by varying the loading from 5 to 40 wt %. The epoxy resins were cured with 4,4′‐diaminodiphenylsulfone and subjected to tests for thermal properties, plane strain fracture toughness (K_IC), flexural properties, and solvent resistance measurements. The fracture surfaces were analyzed with SEM to elucidate the toughening mechanism. The properties of copolymer‐toughened epoxy resins were compared to those of samples modified by PES/CTBN blends, PES oligomer, or CTBN. The PES‐CTBN‐PES copolymer (20K) showed a K_IC of 2.33 MPa m^0.5 at 40 wt % loading while maintaining good flexural properties and chemical resistance. However, the epoxy resin modified with a CTBN/8K PES blend (2:1) exhibited lower K_IC (1.82 MPa m^0.5), lower flexural properties, and poorer thermal properties and solvent resistance compared to the 20K PES‐CTBN‐PES copolymer‐toughened samples. The high fracture toughness with the PES‐CTBN‐PES copolymer is believed to be due to the ductile fracture of the continuous PES‐rich phases, as well as the cavitation of the rubber‐rich phases. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1556–1565, 2002; DOI 10.1002/app.10390     

Toughening of epoxy resin by functional‐terminated polyurethanes and/or semicrystalline polymer powders

Hydroxyl‐, amine‐, and anhydride‐terminated polyurethane (PU) prepolymers, which were synthesized from polyether [poly(tetramethylene glycol)] diol, 4,4′‐diphenylmethane diisocyanate, and a coupling agent, bisphenol‐A (Bis‐A), 4,4′‐diaminodiphenyl sulphone (DDS), or benzophenonetetracarboxylic dianhydride, were used to modify the toughness of Bis‐A diglycidyl ether epoxy resin cured with DDS. Besides the crystalline polymers, poly(butylene terephthalate) (PBT) and poly(hexamethylene adipamide) (nylon 6,6), with particle sizes under 40 μm were employed to further enhance the toughness of PU‐modified epoxy at a low particle content. As shown by the experimental results, the modified resin displayed a significant improvement in fracture energy and also its interfacial shear strength with polyaramid fiber. The hydroxyl‐terminated PU was the most effective among the three prepolymers. The toughening mechanism is discussed based on the morphological and the dynamic mechanical behavior of the modified epoxy resin. Fractography of the specimen observed by the scanning electron microscopy revealed that the modified resin had a two‐phase structure. The fracture properties of PBT‐particle‐filled epoxy were better than those of nylon 6,6‐particle‐filled epoxy. Nevertheless, the toughening effect of these crystalline polymer particles was much less efficient than that of PU modification. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 2903–2912, 2001     

Mechanical and thermal properties of novel rubber‐toughened epoxy blend prepared by in situ pre‐crosslinking

A novel method is used for preparing liquid rubber‐toughened epoxy blend, in which an initiator was added to the liquid rubber–epoxy mixture to initiate crosslinking reaction of liquid rubber, and then curing agent was added to form the thermoset. Two epoxy blends with carboxyl‐terminated butadiene‐acrylonitrile copolymers were prepared using traditional and novel methods respectively. Results indicated that the novel rubber‐toughened epoxy blend exhibited much better mechanical properties than its traditional counterpart. The morphologies of the blends were explored by transmission electron microscopy (TEM), it was revealed that the use of the novel method formed a local interpenetrating network structure in the blend, which substantially improved the interfacial adhesion. The impact fracture surfaces of the two blends were observed by scanning electron microscopy (SEM) to explore the toughening mechanism, it was found that crack pinning was the major toughening mechanism for the novel rubber‐toughened epoxy blend. Dynamic mechanical analysis (DMA) was applied to determine the T_g values of the blends, which were found to be close. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41110.     

Fracture behavior of core‐shell rubber–modified clay‐epoxy nanocomposites

Morphology and fracture mechanisms in two nanoclay‐filled epoxy systems were investigated using both microscopy and spectroscopy tools. Clay exfoliation was achieved using a series of sample preparation steps, and confirmed using wide angle X‐ray diffraction (XRD) and transmission electron microscopy (TEM) techniques. Significant improvement in modulus was obtained when clay exfoliation was achieved. Incorporation of core‐shell rubber (CSR) in both caly‐filled epoxy systems leads to greatly enhanced fracture toughness. Optical microscopy and TEM observations of the CSR‐modified nanocomposites suggest that CSR cavitation. shear yielding of the matrix, clay layer delamination. CSR bridging, crack bifurcation. and crack deflection are among the operative toughening mechanisms observed, depending on the nature of the epoxy matrix utilized.     

Fracture behavior of styrene‐ethylene‐propylene rubber‐toughened polypropylene

The morphology and fracture behavior of isotactic polypropylene toughened by styrene‐ethylene‐propylene (PP/SEP) were investigated. The SEP rubber, having an average particle size of 0.2 µm, is found to be well dispersed in the PP matrix. The fracture toughness of SEP‐modified PP is greatly improved. The toughening mechanism investigation shows that a widespread crazing zone is generated in the crack tip damage zone. An intense narrow damage band in the center of crazed zone is formed. Crazing and shear yielding are found to be the dominant toughening mechanisms in PP/SEP. The crazes are initiated only by large SEP particles in the blend. The small SEP particles (< 0.3 µm) can neither cavitate nor trigger crazing. As a result, large scale shear deformation is suppressed in this blend. These findings are consistent with the notion that the crack tip plane strain constraint has to be relieved in magnitude in order for the deviatoric stress to reach a critical value for widespread shear banding.     

橡胶增韧环氧树脂低温韧性的研究

以低分子量聚酰胺(PA300)为固化剂,以液体端羧基丁腈橡胶(CTBN)为增韧剂增韧改性双酚A型环氧树脂,考察了橡胶增韧剂、固化剂、稀释剂和无机填料对环氧树脂低温韧性的影响。通过对增韧体系应力应变特性和动态力学性能的研究表明,该体系具有优异的低温韧性。     

Role of core‐shell rubber particle cavitation resistance on toughenability of epoxy resins

The role of rubber particle cavitation resistance on toughening of epoxy resins is still unresolved. In this research, the role of rubber particle cavitation resistance was exclusively studied. Two types of core‐shell rubber (CSR) particles with different cavitation resistances were utilized for modifying epoxy resin. Matrix crosslink density (XLD) was varied by using nonstoichiometric amounts of hardener. Fracture toughness values of neat and CSR‐modified epoxy samples decreased with lowering of XLD via deviation from stoichiometric point. It was resulted by higher modulus and lower elongation at break of the nonstoichiometric samples, and also antiplasticization of epoxy networks resulted from suppression of β‐transition relaxation motions. In all XLDs, the CSR particles with higher core T_g and modulus yielded higher fracture energy. Results showed that core properties such as T_g and modulus of CSR particles had a significant effect on toughening of the epoxy networks. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Preparation of poly(1,4‐cyclohexylenedimethylene phthalate)s and their use as modifiers for aromatic diamine‐cured epoxy resin

Poly(1,4‐cyclohexylenedimethylene phthalate) s, prepared by the reaction of phthalic anhydride and 1,4‐cyclohexane dimethanol (35/65 or 73/27 mol % cis/trans or trans alone), have been used to improve the toughness of bisphenol‐A diglycidyl ether epoxy resin cured with 4,4′‐diaminodiphenyl sulfone. The aromatic polyesters include poly(cis/trans‐1,4‐cyclohexylenedimethylene phthalate) (PCP) based on a commercial cyclohexanedimethanol, poly(trans‐1,4‐cyclohexylenedimethylene phthalate) (trans‐PCP) and poly(cis/trans‐1,4‐cyclohexylenedimethylene phthalate) (cis‐rich PCP) prepared from a cis‐rich diol. The polyesters used were soluble in the epoxy resin without solvents and were effective as modifiers for toughening the cured epoxy resin. For example, the inclusion of 20 wt% of PCP (MW 6400 g mol⁻¹) led to an 80% increase in the fracture toughness (K_IC) of the cured resin with no loss of mechanical and thermal properties. The toughening mechanism is discussed in terms of morphological and dynamic viscoelastic behaviours of the modified epoxy resin system. © 2000 Society of Chemical Industry     

Morphology and properties of an epoxy alloy system containing thermoplastics and a reactive rubber

A novel approach for toughening thermosetting epoxy matrices using both thermoplastics and liquid reactive rubbers as modifiers has been investigated. The network structure of the modified epoxy systems was characterized using dynamic mechanical analysis, and the morphology of the multiphase structure was examined using scanning electron microscopy (SEM). To investigate the continuity of the phase domains, the constituents in the phase domains were positively identified using solving etching and RuO₄ staining techniques for transmission electron microscopy (TEM). The fracture toughness of the modified and basic epoxy samples was measured using compact tension (CT) specimens. Quite limited toughness improvement was achieved for the epoxy modified with only the PSu thermoplastic, or the liquid rubber by itself. However, the fracture toughness was found to increase dramatically when a proper combination of both the liquid reactive rubber and thermoplastic was simultaneously incorporated into the epoxy. Toughening by using dual modifiers resulted in maximum improvement of fracture toughness with minimal compromises in processability and T_g depression by rubbers.     

Temperature effects on rigid nano‐silica and soft nano‐rubber toughening in epoxy under impact loading

The rigid nano‐silica and soft nano‐rubber toughening effects on neat epoxy under impact loading in a range of ?50 to 80 °C were investigated. Nanosilica particles (20 nm) toughened neat epoxy at all temperatures with a maximum toughening efficiency at ?50 °C and lower efficiency at elevated temperatures. In contrast, except at ?50 °C, nano‐rubber particles (100 nm) showed the deterioration effect on the impact fracture toughness of epoxy resin. Scanning electron microscopy examinations revealed that the crack pinning and local epoxy deformation induced by rigid particles in term of nano‐silica/epoxy and nano‐rubber/epoxy interfacial debonding (at ?50 °C) led to positive toughening efficiency on neat epoxy. However, at 20 and 80 °C, the rubber cavitations/void plastic growth was significantly suppressed under the impact loading, which led to the negative toughening efficiency on epoxy. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 45319.     

Control of morphologies and mechanical properties of thermoplastic‐modified epoxy matrices by addition of a second thermoplastic

Ternary mixtures based on stoichiometric mixtures of the diglycidyl ether of bisphenol‐A (DGEBA) and 4,4′‐diaminodiphenyl sulfone (DDS) and two miscible thermoplastics, poly(methyl methacrylate) (PMMA) and the poly(hydroxy ether of bisphenol‐A) (phenoxy), were investigated by optical microscopy (OM), atomic force microscopy (AFM) and dynamic mechanical analysis (DMA). Mechanical testing was used to study the ultimate behavior. All the modified epoxy mixtures were heterogeneous. DMA has been shown to be an excellent technique for detecting the morphologies generated after curing when the loss modulus is used for analysis. Morphology varied with the thermoplastic content on the mixtures. The addition of a second thermoplastic in small amounts changed the morphological features from particulated to co‐continuous and from that to phase‐inverted morphologies. A significant increase in fracture toughness was observed above all for the mixtures with some level of co‐continuity within the epoxy‐rich matrix. Phase inversion led to poor strength and also fracture toughness. Copyright © 2003 Society of Chemical Industry     

环氧树脂/ABS复合材料的制备及性能表征

以环氧树脂为基体,苯乙烯-丙烯腈-丁二烯（ABS）树脂为增韧剂,制备了环氧树脂/ABS复合材料,讨论了增韧剂对复合材料的热性能和机械性能的影响。结果表明,ABS的添加可提高复合材料的断裂韧性。扫描电镜结果显示,基体的剪切屈服和橡胶颗粒的微孔洞是ABS增韧环氧树脂的主要增韧机理。     

Mechanical properties of epoxy resin/hydroxyl‐terminated polyester blends: effect of two‐phase structure

In this paper, the effect of two‐phase structure on the mechanism of rubber‐toughening of epoxy resins was studied. Three types of hydroxyl‐terminated polyesters with different molecular weights were synthesized in order to modify epoxy resins to obtain single‐phase (P‐1), critical phase separation (P‐2) and two‐phase (P‐3) structures. The results of dynamical mechanical analysis and scanning electron microscopy distinguished the dissolved and phase‐separated polyesters in the epoxy matrix. The P‐1 system showed the highest dissolved content of polyester in the epoxy matrix, while the P‐3 system exhibited the lowest content. Both dissolved and phase‐separated polyesters proved to be capable of increasing the toughness of modified epoxy resins. The phase‐separated polyester was found to contribute much more to the improvement of toughness. Copyright © 2005 Society of Chemical Industry     

Thermal and mechanical properties of PPO filled epoxy resins compatibilized by triallylisocyanurate

A series of blends has been prepared by adding a poly(phenylene oxide) (PPO), in varying proportions, to an epoxy resin cured with dicyandiamide. All the materials show two‐phase morphology when characterized by SEM and DMA. SEM and DMA indicate that partial mixing exists in all the blends especially with high PPO content. This implies that the epoxy oligomer or low crosslinking density epoxy exists in the PPO phase after curing. The tensile strength and modulus of these blends are nearly independent of the PPO content, while the fracture toughness (G_IC) is improved by PPO. However, the two‐phase particulate morphology is not uniform. In order to improve the uniformity and miscibility, triallylisocyanurate (TAIC) has been used as an in situ compatibilizer for the polymer blends of epoxy and PPO. SEM and DMA reveal improvement of miscibility and solvent resistance for this system. The fracture toughness of these TAIC‐modified systems are also improved by adding TAIC (0–20 phr). © 2000 Society of Chemical Industry     

Preparation and properties of high performance phthalide‐containing bismaleimide modified epoxy matrices

A series of intercrosslinked networks formed by diglycidyl ether of bisphenol A epoxy resin (DGEBA) and novel bismaleimide containing phthalide cardo structure (BMIPP), with 4,4′‐diamino diphenyl sulfone (DDS) as hardener, have been investigated in detail. The curing behavior, thermal, mechanical and physical properties and compatibility of the blends were characterized using differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA), notched Izod impact test, scanning electron microscopy (SEM) and water absorption test. DSC investigations showed that the exothermic transition temperature (T_p) of the blend systems shifted slightly to the higher temperature with increasing BMIPP content and there appeared a shoulder on the high‐temperature side of the exothermic peak when BMIPP content was above 15 wt %. TGA and DMA results indicated that the introduction of BMIPP into epoxy resin improved the thermal stability and the storage modulus (G′) in the glassy region while glass transition temperature (T_g) decreased. Compared with the unmodified epoxy resin, there was a moderate increase in the fracture toughness for modified resins and the blend containing 5 wt % of BMIPP had the maximum of impact strength. SEM suggested the formation of homogeneous networks and rougher fracture surface with an increase in BMIPP content. In addition, the equilibrium water uptake of the modified resins was reduced as BMIPP content increased. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preparation and properties of MWCNTs/poly(acrylonitrile‐ styrene‐butadiene)/epoxy hybrid composites

Poly(acrylonitrile‐styrene‐butadiene) (ABS) was used to modify diglycidyl ether of bisphenol‐A (DGEBA) type epoxy resin, and the modified epoxy resin was used as the matrix for making multiwaled carbon tubes (MWCNTs) reinforced composites and were cured with diamino diphenyl sulfone (DDS) for better mechanical and thermal properties. The samples were characterized by using infrared spectroscopy, pressure volume temperature analyzer (PVT), thermogravimetric analyzer (TGA), dynamic mechanical analyzer (DMA), thermo mechanical analyzer (TMA), universal testing machine (UTM), and scanning electron microscopy (SEM). Infrared spectroscopy was employed to follow the curing progress in epoxy blend and hybrid composites by determining the decrease of the band intensity due to the epoxide groups. Thermal and dimensional stability was not much affected by the addition of MWCNTs. The hybrid composite induces a significant increase in both impact strength (45%) and fracture toughness (56%) of the epoxy matrix. Field emission scanning electron micrographs (FESEM) of fractured surfaces were examined to understand the toughening mechanism. FESEM micrographs reveal a synergetic effect of both ABS and MWCNTs on the toughness of brittle epoxy matrix. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Influences of liquid elastomer additive on the behavior of short glass fiber reinforced epoxy

In this study, improvements in mechanical and thermal behavior of short glass fiber (GF) reinforced diglycidyl ether of bisphenol-A (DGEBA) based epoxy with hydroxyl terminated polybutadiene (HTPB) modification have been studied. A silane coupling agent (SCA) with a rubber reactive group was also used to improve the interfacial adhesion between glass fibers and an epoxy matrix. 10, 20, and 30 wt% GF reinforced composite specimens were prepared with and without silane coupling agent treatment of fibers and also HTPB modification of epoxy mixture. In the ruber modified specimens, hardener and HTPB were premixed and left at room temperature for 1 hr before epoxy addition. In order to observe the effects of short glass fiber reinforcement of epoxy matrix, silane treatment of fiber surfaces, and also rubber modification of epoxy on the mechanical behavior of specimens, tension and impact tests were performed. The fracture surfaces and thermal behavior of all specimens were examined by scanning electron microscope (SEM), and dynamic mechanical analysis (DMA), respectively. It can be concluded that increasing the short GF content increased the tensile and impact strengths of the specimens. Moreover, the surface treatment of GFs with SCA and HTPB modification of epoxy improved the mechanical properties because of the strong interaction between fibers, epoxy, and rubber. SEM studies showed that use of SCA improved interfacial bonding between the glass fibers and the epoxy matrix. Moreover, it was found that HTPB domains having relatively round shapes formed in the matrix. These rubber domains led to improved strength and toughness, due mainly to the “rubber toughening” effect in the brittle epoxy matrix.     

Preparation and properties of TiO2‐filled poly(acrylonitrile‐butadiene‐styrene)/epoxy hybrid composites

Poly (acrylonitrile‐butadiene‐styrene) (ABS) was used to modify diglycidyl ether of bisphenol‐A type of epoxy resin, and the modified epoxy resin was used as the matrix for making TiO₂ reinforced nanocomposites and were cured with diaminodiphenyl sulfone for superior mechanical and thermal properties. The hybrid nanocomposites were characterized by using thermogravimetric analyzer (TGA), dynamic mechanical analyzer (DMA), universal testing machine (UTM), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The bulk morphology was carefully analyzed by SEM and TEM and was supported by other techniques. DMA studies revealed that the DDS‐cured epoxy/ABS/TiO₂ hybrid composites systems have two T_gs corresponding to epoxy and ABS rich phases and have better load bearing capacity with the addition of TiO₂ particles. The addition of TiO₂ induces a significant increase in tensile properties, impact strength, and fracture toughness with respect to neat blend matrix. Tensile toughness reveals a twofold increase with the addition of 0.7 wt % TiO₂ filler in the blend matrix with respect to neat blend. SEM micrographs of fractured surfaces establish a synergetic effect of both ABS and TiO₂ components in the epoxy matrix. The phenomenon such us cavitation, crack path deflection, crack pinning, ductile tearing of the thermoplastic, and local plastic deformation of the matrix with some minor agglomerates of TiO₂ are observed. However, between these agglomerates, the particles are separated well and are distributed homogeneously within the polymer matrix. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013