Blends of bisphenol A‐based cyanate ester and bismaleimide: Cure and thermal characteristics

A dicyanate ester, namely, 2,2‐bis‐(4‐cyanatophenyl)propane, and a bismaleimide, namely, 2,2‐bis[4‐(4‐maleimido phenoxy)phenyl]propane, possessing closely resembling backbone structures, were cured together to derive bismaleimide–triazine network polymers of varying compositions. The blend manifested a eutectic melting behavior at a 1 : 1 composition with a eutectic melting point of 15°C. The cure characterization of the blends was done by DSC and dynamic mechanical analyses (DMA). The near simultaneous cure of the blend could be transformed to a clear sequential one by catalyzing the dicyanate cure to lower temperature using dibutyl tin dilaurate. The two‐stage, independent cure of the components of the blend evidenced in DSC was confirmed by DMA. The cure profile of the bismaleimide component predicted from the kinetic data derived from nonisothermal DSC was found to be in league with the isothermal DMA behavior. Both techniques led to optimization of the cure schedule of the blends. The cured polymers were characterized by FTIR and TGA. The cured blends underwent decomposition in two stages, each corresponding to the polycyanurate and polybismaleimide. Enhancing the bismaleimide component did not alter the initial decomposition temperature, but led to reduced rate of thermal degradation at higher temperature. Interlinking of the two networks and enhancing crosslink density through coreaction of the blend with 4‐cyantophenylmaleimide unaffected the initial decomposition properties but was conducive for increasing the char residue significantly. Computation of activation parameters for the thermal decomposition of the polymers confirmed that the first step in the degradation of the blends is caused by the polycyanurate component. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 3365–3375, 1999     

Effect of blending polyethersulfone on the cure kinetics and physical properties of dicyanate resin

The curing behavior and thermomechanical properties of dicyanate/polyethersulfone (PES) blends were investigated. Differential scanning calorimetry (DSC) was used to study the curing behavior of the dicyanate/PES blends. A second‐order autocatalytic reaction mechanism was used to describe the cure kinetics of the blends. The reaction kinetic parameters were determined by fitting DSC conversion data to the kinetic equation. The main glass‐transition temperatures of the blends decreased with increasing PES content. Two glass‐transition temperatures indicating phase‐separated morphology of the blends were observed. The thermal decomposition behavior of the blends was measured using thermogravimetric analysis. Mechanical and electrical properties of the blends were investigated. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 1952–1962, 2001     

Phase separation,cure kinetics,and morphology of epoxy/poly(vinyl acetate) blends

Epoxy based on diglycidyl ether of bisphenol A + 4,4′diaminodiphenylsulfone blended with poly(vinyl acetate) (PVAc) was investigated through differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA) and environmental scanning electron microscopy (ESEM). The influence of PVAc content on reaction induced phase separation, cure kinetics, morphology and dynamic‐mechanical properties of cured blends at 180°C is reported. Epoxy/PVAc blends (5, 10 and 15 wt % of PVAc content) are initially miscible but phase separate upon curing. DMTA α‐relaxations of cured blends agree with T_g results by DSC. The conversion‐time data revealed the cure reaction was slower in the blends than in the neat system, although the autocatalytic cure mechanism was not affected by the addition of PVAc. ESEM showed the cured epoxy/PVAc blends had different morphologies as a function of PVAc content: an inversion in morphology took place for blends containing 15 wt % PVAc. The changes in the blend morphology with PVAc content had a clear effect on the DMTA behavior. Inverted morphology blends had low storage modulus values and a high capability to dissipate energy at temperatures higher than the PVAc glass‐transition temperature, in contrast to the behavior of neat epoxy and blends with a low PVAc content. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1507–1516, 2007     

Cure kinetics and physical properties of dicyanate/polyetherimide semi‐IPNs

The curing behavior and physical properties of dicyanate/polyetherimide (PEI) semi‐interpenetrating polymer network (IPN) systems were investigated. Differential scanning calorimetry (DSC) was used to study the curing behavior of the dicyanate/PEI semi‐IPN systems. The curing rate of the semi‐IPN system decreased as the PEI content increased. An autocatalytic reaction mechanism can describe well the curing kinetics of the semi‐IPN systems. The reaction kinetic parameters were determined by fitting DSC conversion data to the kinetic equation. The glass transition temperature of the semi‐IPNs decreased with increasing PEI content. Two glass transitions due to phase‐separated morphology were observed for the semi‐IPN containing over 15 phr (parts per hundred parts of dicyanate resin) PEI. The thermal stability and dynamic mechanical properties of the semi‐IPNs were measured by thermal analysis.     

Synthesis and properties of a novel bismaleimide resin containing 1,3,4‐oxadiazole moiety and the blend systems thereof with epoxy resin

A new bismaleimide monomer, 2‐((4‐maleimidophenoxy)methyl)‐5‐(4‐maleimidophenyl)‐1,3,4‐oxadiazole (Mioxd), was designed and synthesized. The chemical structure of the monomer was confirmed by means of Fourier transform infrared (FTIR) spectroscopy, proton nuclear magnetic resonance (¹H NMR) spectroscopy and elemental analysis, and its thermal properties were characterized using differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). Mioxd as a reactive modifier was blended with epoxy resin based on bisphenol A diglycidyl ether (DGEBA) in weight ratio of 5, 10, and 15%, using 4,4′‐diaminodiphenyl sulfone (DDS) as hardener. The effect of Mioxd addition on the cure behavior and thermal properties of the blend resins was studied by DSC, TGA, and dynamic mechanical analysis (DMA). DSC investigations showed that the main exothermic peak temperature (T_p) of the blend systems did not obviously shift with increasing Mioxd content whereas a new shoulder appeared and gradually grew on the high temperature side of the exothermic peak. The results of DMA measurements exhibited the glassy storage modulus (G') and glass transition temperatures (T_g) increased as the Mioxd content was increased, the cured blends investigated were miscible and no phase separation occurred. Further, the thermal decomposition temperature first decreased and then increased, but the char yield at 600°C increased with an increase in Mioxd content. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Mechanical and thermal properties of glass bead–filled nylon‐6

The mechanical and thermal properties of glass bead–filled nylon‐6 were studied by dynamic mechanical analysis (DMA), tensile testing, Izod impact, thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC) tests. DMA results showed that the incorporation of glass beads could lead to a substantial increase of the glass‐transition temperature (T_g) of the blend, indicating that there existed strong interaction between glass beads and the nylon‐6 matrix. Results of further calculation revealed that the average interaction between glass beads and the nylon‐6 matrix deceased with increasing glass bead content as a result of the coalescence of glass beads. This conclusion was supported by SEM observations. Impact testing revealed that the notch Izod impact strength of nylon‐6/glass bead blends substantially decreased with increasing glass bead content. Moreover, static tensile measurements implied that the Young's modulus of the nylon‐6/glass bead blends increased considerably, whereas the tensile strength clearly decreased with increasing glass bead content. Finally, TGA and DSC measurements indicated that the thermal stability of the blend was obviously improved by incorporation of glass beads, whereas the melting behavior of the nylon‐6 remained relatively unchanged with increasing glass bead content. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1885–1890, 2004     

Dynamically cured polypropylene/Novolac blends compatibilized with maleic anhydride‐g‐polypropylene

In this article, the dynamic vulcanization process was applied to polypropylene (PP)/Novolac blends compatibilized with maleic anhydride‐grafted PP (MAH‐g‐PP). The influences of dynamic cure, content of MAH‐g‐PP, Novolac, and curing agent on mechanical properties of the PP/Novolac blends were investigated. The results showed that the dynamically cured PP/MAH‐g‐PP/Novolac blend had the best mechanical properties among all PP/Novolac blends. The dynamic cure of Novolac improved the modulus and stiffness of the PP/Novolac blends. The addition of MAH‐g‐PP into dynamically cured PP/Novolac blend further enhanced the mechanical properties. With increasing Novolac content, tensile strength, flexural modulus, and flexural strength increased significantly, while the elongation at break dramatically deceased. Those blends with hexamethylenetetramine (HMTA) as a curing agent had good mechanical properties at HMTA content of 10 wt %. Scanning electron microscopy (SEM) analysis showed that dynamically cured PP/MAH‐g‐PP/Novolac blends had finer domains than the PP/MAH‐g‐PP/Novolac blends. Thermogravimetric analysis (TGA) results indicated that the incorporation of Novolac into PP could improve the thermal stability of PP. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Miscibility, thermal characterization and crystallization of poly(l-lactide) and poly(tetramethylene adipate-co-terephthalate) blend membranes

Binary blend membranes of biodegradable poly(l-lactide) (PLLA) with poly(tetramethylene adipate-co-terephthalate) (PTAT) copolymer were prepared by solution casting via air evaporation. The miscibility of PLLA/PTAT blends was studied by dynamic mechanical analysis (DMA) and thermal mechanical analysis (TMA) in a tensile mode. Differential scanning calorimetry (DSC) measurement was carried out. The surface microstructure and tensile properties of the blend membranes were examined using atomic force microscopy (AFM) and tensile tester. It was concluded that PLLA/PTAT blends should be partially miscible for all ranges of compositions. Higher roughness and porosity were observed for the blend containing 50% PTAT, suggesting more phase separation occurred. The DSC analysis showed that the fusion enthalpy and crystallinity (X_c) of the PLLA-rich phase decreased with increasing PTAT content. Solidification process strongly suggested that the crystallization rate was accelerated by blending with 25% PTAT content, which served as the nucleation agent. Furthermore, the crystallization rate coefficient (CRC) depended on the blending miscibility and cooling rate in the non-isothermal crystallization process. Besides, PTAT addition could be proved to enhance the thermal stability and elongation of resulting blend membranes, even superior to those properties of poly(lactic acid-co-glycolic acid) (PLGA).     

Ternary blends of acrylic rubber,poly(butylene terephthalate), and liquid crystalline polymer: Influence of interactions on thermal and dynamic mechanical properties

The ternary blends of acrylate rubber (ACM), poly(butylene terephthalate) (PBT), and liquid crystalline polymer (LCP) were prepared by varying the amount of LCP but fixing the ratio of ACM and PBT, using melt mixing procedure. The influence of interactions on thermal and dynamic mechanical properties of the blends was investigated over the complete composition range. The techniques applied were Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), thermogravimetry (TG), and dynamic mechanical analysis (DMA). The FTIR spectroscopy analysis showed reduction in the intensity of the peak corresponding to epoxy groups of ACM with increasing heating time at 290°C. This implies that there is a chemical reaction between the epoxy and end groups of PBT and LCP. Glass transition temperature (T_g) and melting temperature (T_m) of the blends were affected depending on the LCP weight percent in the ACM/PBT blend, respectively. This further suggests the strong interfacial interactions between the blend components. In presence of ACM, the nucleating effect of LCP was more pronounced for the PBT phase. The thermogravimetric study showed improved thermal stability for the blends with the increasing LCP content. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3904–3912, 2006     

Bisphenol A dicyanate–novolac epoxy blend: Cure characteristics,physical and mechanical properties,and application in composites

Reactive blends of bisphenol A dicyanate (BACY) and a novolac epoxy resin (EPN) were investigated for their cure behavior and the mechanical, thermal, and physical properties of the cocured neat resin and glass‐laminate composites. Contrary to the apparent observation in DSC, the dynamic mechanical analysis confirmed a multistep cure reaction of the blend, in league with an established reaction path for similar systems. The cured matrix was found to contain both polycyanurate and oxazolidinone networks that existed in discrete phases exhibiting independent glass transitions in dynamic mechanical analysis (DMA). The flexible and less crosslinked oxazolidinone network contributed to enhanced flexural strength at the cost of the tensile strength of the neat resin. The increased resin flexibility was, however, not translated to the glass‐laminate composite for which the flexural strength decreased with the oxazolidinone content, although the latter was conducive for rendering a stronger interphase. The presence of oxazolidinone adversely affected the thermal stability of the cured resin and the high‐temperature performance of both neat resin and the composites. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1675–1685, 1999     

Mechanical properties of high temperature cyanate ester/BMI blend composites

A new Schiff base functionalized dicyanate ester was synthesized and the monomer was characterized by FTIR, ¹H-NMR, ¹³C-NMR and elemental analysis techniques. This prepared dicyanate ester with catalyst was then blended with BMI resin at different ratios by solution technique. The composites were made by impregnating the fibers with the blend solution followed by curing at various time-temperature schedules. The mechanical properties of the blend composites were tested. The fiber volume fraction of the composites were found to be in the range 41 ± 3%. The mechanical properties such as tensile modulus (32–35 GPa), flexural modulus (56–59 GPa) and Mode I fracture toughness (G_IC = 104–136 J/m²) and impact response (1,121–1,218 J/m) were found to increase with increasing cyanate ester content in the Cy/BMI blends. From the DMA study it was observed that as the cyanate content increases from 3 to 9% in the blend the tan δ value increases from 0.112 to 0.126 and the storage modulus decreases from 24,750 to 22,870 MPa indicating that the crosslink density of the blends decreases. The SEM analysis shows the absence of phase separation. Moisture absorption and chemical resistance of the blend composites increase with increasing cyanate content. POLYM. COMPOS., 2009. © 2009 Society of Plastics Engineers     

Effects of epoxy content on dynamic mechanical behaviour of PEI‐toughened dicyanate–novolac epoxy blends

By varying the cyanate/epoxy ratio, three polyetherimide(PEI)‐modified bisphenol A dicyanate–novolac epoxy resin blends with different epoxy contents were prepared. The effects of epoxy content on the dynamic mechanical behaviour of those blends were investigated by dynamic mechanical thermal analysis. The results showed that the glass transition temperature of the cyanate–epoxy network (T_g1) in the modified blend decreases with epoxy content. When the epoxy content increases, both the width of the glass transition of the cyanate–epoxy network and its peak density are depressed substantially. Although the tangent delta peak value of PEI is basically independent of epoxy content, the T_g of PEI (T_g2) decreases with epoxy content. T_g1 is independent of the PEI loading. When T_g1 is lower than T_g2, however, the T_g1 in the blend with revised phase structure is substantially lower than other blends. Copyright © 2004 Society of Chemical Industry     

Viscoelastic and adhesion properties of EVA/tackifier/wax ternary blend systems as hot-melt adhesives

Two types of wax were added to a ethylene vinyl acetate (EVA) copolymer/aromatic hydrocarbon resin (tackifier) blend in the molten state and the miscibility, viscoelastic and adhesion properties of ternary blends as hot-melt adhesives (HMAs) were investigated. Miscibility and viscoelastic properties were studied using differential scanning calorimetry (DSC), Brookfield viscometry and dynamic mechanical thermal analysis (DMTA), and their adhesion strength was determined in terms of single lap shear strength. DSC thermograms of both types of waxes showed their melting peaks in a similar region to that of EVA/tackfier blend. It was difficult to evaluate the miscibility of ternary blends using DSC because the melting peaks of the waxes overlapped with those of the EVA/tackifier blend, although the glass transition temperature (T _g) of the ternary blend systems slightly increased with increasing wax concentration. However, their storage modulus (E′) increased slightly and loss tangent (tan δ) showed different peaks when two types of wax were added to the EVA/tackifier blend. Therefore, the miscibility of EVA/tackifier blend altered with addition of waxes. In addition, their melt viscosity decreased with increasing wax concentration. Furthermore, the adhesion strength of the ternary blends decreased with increasing wax concentration, despite the increment of storage modulus. These results suggested that the ternary blends of EVA/tackifier/wax were heterogeneous.     

Blends of poly[3,3-bis(chloromethyl)oxetane] with poly(vinyl acetate). I. Thermal and mechanical properties

Blends of poly[3,3-bis(chloromethyl)oxetane] (Penton) with poly(vinyl acetate) were prepared. Compatibility, morphology, thermal behavior, and mechanical properties of blends with various compositions were studied using differential scanning calorimetry (DSC), dynamic mechanical measurements (DMA), tensile tests, and scanning electron microscopy (SEM). DMA study showed that the blends have two glass transition temperatures (T_g). The T_g of the PVAc rich phase shifts significantly to lower temperatures with increasing Penton content, suggesting that a considerable amount of Penton dissolves in the PVAc rich phase, but that the Penton rich phase contains little PVAc. The Penton/PVAc blends are partially compatible. DSC results suggest that PVAc can act as a β-nucleator for Penton in the blend. Marked negative deviations from simple additivity were observed for the tensile strength at break over the entire composition range. The Young's modulus curve appeared to be S-shaped, implying that the blends are heterogeneous and have a two-phase structure. This was confirmed by SEM observations. © 1992 John Wiley & Sons, Inc.     

Rheology and thermal properties of liquid crystalline copolyester and poly(ethylene 2,6-naphthalate) blends

Blends of a poly(ethylene 2,6-naphthalate) (PEN) and a liquid crystalline copolyester (LCP), poly(benzoate-naphthoate) were prepared in a twin-screw extruder. Specimens for thermal properties were investigated by means of an instron capillary rheometer (ICR) and scanning electron microscopy (SEM). The blend viscosity showed a minimum at 10 wt% of LCP and increased with increasing LCP content above 10 wt% of LCP. Above 50% of LCP and at higher shear rate, phase inversion occured and the blend morphology was fibrous and similar to pure LCP. The ultimate fibrillar structure of LCP phase appeared to be closely related to the extrusion temperature. By employing a suitable deformation history, the LCP phase may be elongated and oriented such that a microfibrillar morphology can be retained in the solid state. Thermal properties of the LCP/PEN blends were studied using DSC and a Rheovibron viscoelastomer. These blends were shown to be incompatible in the entire range of the LCP content. For the blends, the T_g and Tm were unchanged. The half time of crystallization for the LCP/PEN blends decreased with increasing LCP content. Therefore, the LCP acted as a nucleating agent for the crystallization of PEN. The dimensional and thermal stability of the blends were increased with increasing LCP content. In studies of dynamic mechanical properties, the storage modulus (E′) was improved with increasing LCP content and synergistic effects were observed at 70 wt% of LCP content. The storage modulus for the LCP/PEN 70/30 blend is twice that of PEN matrix and exceeded pure LCP.     

Polymerization kinetics and thermal properties of dicyanate/clay nanocomposites

The polymerization kinetics and thermal properties of dicyanate/clay nanocomposites were investigated. A type of organically modified clay was used as nanometer‐size fillers for the thermosetting dicyanate resin. Differential scanning calorimetry (DSC) was used to study the curing behavior of the dicyanate/clay nanocomposite systems. The polymerization rate of the nanocomposite systems increased with increasing clay content. An autocatalytic reaction mechanism could adequately describe the polymerization kinetics of the dicyanate/clay nanocomposite systems. The polymerization kinetic parameters were determined by fitting the DSC conversion data to the proposed kinetic equation. The glass‐transition temperature of the dicyanate/clay nanocomposites increased with increasing clay content. The thermal decomposition behavior of the dicyanate/clay nanocomposites was investigated by thermogravimetric analysis. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1955–1960, 2004     

Preparation and properties of high performance phthalide‐containing bismaleimide modified epoxy matrices

A series of intercrosslinked networks formed by diglycidyl ether of bisphenol A epoxy resin (DGEBA) and novel bismaleimide containing phthalide cardo structure (BMIPP), with 4,4′‐diamino diphenyl sulfone (DDS) as hardener, have been investigated in detail. The curing behavior, thermal, mechanical and physical properties and compatibility of the blends were characterized using differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA), notched Izod impact test, scanning electron microscopy (SEM) and water absorption test. DSC investigations showed that the exothermic transition temperature (T_p) of the blend systems shifted slightly to the higher temperature with increasing BMIPP content and there appeared a shoulder on the high‐temperature side of the exothermic peak when BMIPP content was above 15 wt %. TGA and DMA results indicated that the introduction of BMIPP into epoxy resin improved the thermal stability and the storage modulus (G′) in the glassy region while glass transition temperature (T_g) decreased. Compared with the unmodified epoxy resin, there was a moderate increase in the fracture toughness for modified resins and the blend containing 5 wt % of BMIPP had the maximum of impact strength. SEM suggested the formation of homogeneous networks and rougher fracture surface with an increase in BMIPP content. In addition, the equilibrium water uptake of the modified resins was reduced as BMIPP content increased. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Mechanical and thermal properties of poly(butylene succinate)/poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) biodegradable blends

Biodegradable polymer blends of poly(butylene succinate) (PBS) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV) were prepared with different compositions. The mechanical properties of the blends were studied through tensile testing and dynamic mechanical thermal analysis. The dependence of the elastic modulus and strength data on the blend composition was modeled on the basis of the equivalent box model. The fitting parameters indicated complete immiscibility between PBS and PHBV and a moderate adhesion level between them. The immiscibility of the parent phases was also evidenced by scanning electron observation of the prepared blends. The thermal properties of the blends were studied through differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). The DSC results showed an enhancement of the crystallization behavior of PBS after it was blended with PHBV, whereas the thermal stability of PBS was reduced in the blends, as shown by the TGA thermograms. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42815.     

Properties and morphologies of elastomer blends modified with EPDM‐g‐poly[2‐dimethylamino ethylmethacrylate]

The graft copolymerization of 2‐dimethylamino ethylmethacrylate (DMAEMA) onto ethylene propylene diene mononer rubber (EPDM) was carried out in toluene via solution polymerization technique at 70°C, using dibenzoyl peroxide as initiator. The synthesized EPDM rubber grafted with poly[DMAEMA] (EPDM‐g‐PDMAEMA) was characterized with ¹H‐NMR spectroscopy, gel permeation chromatography (GPC), differential scanning calorimetry (DSC), and thermal gravimetric analysis (TGA). The EPDM‐g‐PDMAEMA was incorporated into EPDM/butadiene acrylonitrile rubber (EPDM/NBR) blend with different blend ratios, where the homogeneity of such blends was examined with scanning electron microscopy and DSC. The scanning electron micrographs illustrate improvement of the morphology of EPDM/NBR rubber blends as a result of incorporation of EPDM‐g‐PDMAEMA onto that blend. The DSC trace exhibits one glass transition temperature (T_g) for EPDM/NBR blend containing EPDM‐g‐PDMAEMA, indicating improvement of homogeneity. The physico‐mechanical properties after and before accelerated thermal aging of the homogeneous, and inhomogeneous EPDM/NBR vulcanizates with different blend ratios were investigated. The physico‐mechanical properties of all blend vulcanizates were improved after and before accelerated thermal aging, in presence of EPDM‐g‐PDMAEMA. Of all blend ratios under investigation EPDM/NBR (75/25) blend possesses the best physico‐mechanical properties together with the best (least) swelling (%) in brake fluid. Swelling behavior of the rubber blend vulcanizates in motor oil and toluene was also investigated. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Characterization and Properties of Reactive Poly(lactic acid)/Polyamide 610 Biomass Blends

A low molecular weight bisphenol‐A type epoxy resin was used as a reactive compatibilizer for poly(lactic acid) (PLA)/polyamide 610 (PA 610) biomass blends. To the best of our knowledge, this blend is the first biomass PA 610 blend in the literature. The epoxy functional groups could react with the terminal groups of both PLA and PA 610. An ester–amide interchange reaction led to a polyester–polyamide copolymer formation, and improved the compatibility of PLA and PA 610. The blends with epoxy resin showed an enhancement in the phase dispersion and interfacial adhesion compared with the blend without epoxy resin. The differential scanning calorimetry (DSC) analysis showed that the crystallization peak temperatures decreased with increasing epoxy content. The melting temperature of PA 610 decreased with the addition of PLA, but remained unchanged with increased compatibilizer dosages. The dynamic mechanical analysis (DMA) showed that the glass transition temperature (T_g) of the blend, with the addition of 0.5 phr epoxy resin, slightly increased compared with that of neat PLA. However, the T_g of the blends remained unchanged with increasing epoxy resin content, and the higher content of epoxy resin in the blends resulted in improved mechanical properties and higher melt viscosity. The unnotched impact test showed that PA 610 could toughen PLA with the addition of epoxy resin. Moreover, the no‐break unnotched impact behavior was observed with the medium content of the compatibilizer, improving the notch sensitivity of PLA. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 2563–2571, 2013