Effect of the addition of hydrophobic clay on the electrochemical property of polyacrylonitrile/LiClO4 polymer electrolytes for lithium battery

In this study, an organoclay, ALA-MMT, was prepared by the ionic exchange reaction of montmorillonite (MMT) with 12-aminododecanoic acid (ALA). ALA-MMT was then used as a filler to prepare a series of composite polymer electrolytes based on polyacrylonitrile (PAN) and LiClO₄. The effect of the addition of ALA-MMT on the properties of the composite polymer electrolytes (CPEs) was investigated by XRD, FT-IR, DSC, tensile strength, AC impedance, and cyclic voltammetry measurements. It was found that the ALA-MMT particles were well dispersed in the CPEs. Owing to the incorporation of ALA-MMT, a higher fraction of the free anions was obtained, indicating that the lithium salt dissolved in the PAN matrix more effectively for the CPE than in the PAN/LiClO₄ polymer electrolyte. Moreover, the glass-transition temperature was reduced, benefiting the ion transport. The best ionic conductivity at room temperature was obtained from the CPE with 7 wt% of the modified clay and 0.6 M LiClO₄ per PAN repeat unit (CPE-7) and was more than seven times higher than that from the corresponding PAN/LiClO₄ polymer electrolyte (CPE-0). The mechanical property and the cation transference number, t₊, of CPE-7 are largely increased compared to that of CPE-0. Besides, the CPEs were electrochemically stabilized up to 4.75 V and the corresponding cell exhibited excellent electrochemical stability and cyclability over the potential range between 0 V and 4.0 V vs. Li/Li⁺.     

A highly conductive organic-inorganic hybrid electrolyte based on co-condensation of di-ureasil and ethylene glycol-containing alkoxysilane

Organic-inorganic hybrid electrolytes based on di-ureasil backbone structures by reacting poly(propylene glycol)-block-poly(ethylene glycol)-block-poly(propylene glycol) bis(2-aminopropyl ether) (ED2000) with 3-(triethoxysilyl)propyl isocyanate (ICPTES), followed by co-condensation with methoxy(polyethylenoxy)propyl trimethoxysilane (MPEOP) in the presence of LiClO₄ were prepared and characterized by a variety of techniques. The hybrid electrolytes showed good resistance to crystallization and excellent conductivity for use in lithium-ion batteries, as determined by differential scanning calorimetry (DSC) and impedance measurements, respectively. The temperature dependence of the ionic conductivity exhibited a VTF (Vogel-Tamman-Fulcher)-like behavior for all the compositions studied and a maximum ionic conductivity value of 6.9 × 10⁻⁵ S cm⁻¹, a relatively high value for solid polymer electrolytes, was achieved at 30 °C for the hybrid electrolyte with a [O]/[Li] ratio of 16. A microscopic view of the dynamic behavior of the polymer chains (¹³C) and the ionic species (⁷Li) was provided by the ¹H and ⁷Li line widths measured from 2D ¹H-¹³C WISE (Wideline Separation) and variable temperature ⁷Li static NMR, respectively, to elucidate the influence of the mobility of the polymer chains and the charge carriers on the observed ionic conductivity. The present salt-free hybrid electrolyte after plasticization with 1 M LiClO₄ in EC/PC solution exhibited a swelling ratio of 275% and reached an ionic conductivity value up to 8.3 × 10⁻³ S cm⁻¹ at 30 °C, which make it a good candidate for the further development of advanced rechargeable lithium-ion batteries.     

Influence of solvent on the poly (acrylic acid)-oligo-(ethylene glycol) polymer gel electrolyte and the performance of quasi-solid-state dye-sensitized solar cells

The influence of solvents on the property of poly (acrylic acid)-oligo-(ethylene glycol) polymer gel electrolyte and photovoltaic performance of quasi-solid-state dye-sensitized solar cells (DSSCs) were investigated. Solvents or mixed solvents with large donor number enhance the liquid electrolyte absorbency, which further influences the ionic conductivity of polymer gel electrolyte. A polymer gel electrolyte with ionic conductivity of 4.45 mS cm⁻¹ was obtained by using poly (acrylic acid)-oligo-(ethylene glycol) as polymer matrix, and absorbing 30 vol.% N-methyl pyrrolidone and 70 vol.% γ-butyrolactone with 0.5 M NaI and 0.05 M I₂. By using this polymer gel electrolyte coupling with 0.4 M pyridine additive, a quasi-solid-state dye-sensitized solar cell with conversion efficiency of 4.74% was obtained under irradiation of 100 mW cm⁻² (AM 1.5).     

Electrospun hydrophilic fumed silica/polyacrylonitrile nanofiber-based composite electrolyte membranes

Hydrophilic fumed silica (SiO₂)/polyacrylonitrile (PAN) composite electrolyte membranes were prepared by electrospinning composite solutions of SiO₂ and PAN in N,N-dimethylformamide (DMF). Among electrospinning solutions with various SiO₂ contents, the 12 wt% SiO₂ in PAN solution has highest zeta potential (−40.82 mV), and exhibits the best dispersibility of SiO₂ particles. The resultant 12 wt% SiO₂/PAN nanofiber membrane has the smallest average fiber diameter, highest porosity, and largest specific surface area. In addition, this membrane has a three-dimensional network structure, which is fully interconnected with combined mesopores and macropores because of a good SiO₂ dispersion. Composite electrolyte membranes were prepared by soaking these porous nanofiber membranes in 1 M lithium hexafluorophosphate (LiPF₆) in ethylene carbonate (EC)/dimethyl carbonate (DMC) (1:1 vol%). It is found that 12 wt% SiO₂/PAN electrolyte membrane has the highest conductivity (1.1 × 10⁻² S cm⁻¹) due to the large liquid electrolyte uptake (about 490%). In addition, the electrochemical performance of composite electrolyte membranes is also improved after the introduction of SiO₂. For initial cycle, 12 wt% SiO₂/PAN composite electrolyte membrane delivers the discharge capacity of 139 mAh g⁻¹ as 98% of theoretical value, and still retains a high value of 127 mAh g⁻¹ as 89% at 150th cycle, which is significantly higher that of pure PAN nanofiber-based electrolyte membranes.     

Electric double layer capacitors with gelled polymer electrolytes based on poly(ethylene oxide) cured with poly(propylene oxide) diamines

Using a gel electrolyte for electric double layer capacitors usually encountered a drawback of poor contact between the electrolyte and the electrode surface. A gel electrolyte consisting of poly(ethylene oxide) crosslinked with poly(propylene oxide) as a host, propylene carbonate (PC) as a plasticizer, and LiClO₄ as a electrolytic salt was synthesized for double layer capacitors. Diglycidyl ether of bisphenol-A was blended with the polymer precursors to enhance the mechanical properties and increase the internal free volume. This gel electrolyte showed an ionic conductivity as high as 2 × 10⁻³ S cm⁻¹ at 25 °C and was electrochemically stable over a wide potential range (ca. 5 V). By sandwiching this gel-electrolyte film with two activated carbon cloth electrodes (1100 m² g⁻¹ in surface area), we obtained a capacitor with a specific capacitance of 86 F g⁻¹ discharged at 0.5 mA cm⁻², while the capacitance was 82 F g⁻¹ for a capacitor equipped with a liquid electrolyte of 1 M LiClO₄/PC. The capacitance decrease with the current density was less significant for the gel-electrolyte capacitor. We found that the less restricted ion diffusion near the electrolyte/electrode interface led to the smaller overall resistance of the gel-electrolyte capacitor. The high performance of the gel-electrolyte capacitor has demonstrated that the developed polymer network not only facilitated ion motion in the electrolyte bulk phase but also gave an intimate contact with the carbon surface. The side chains of the polymer in the amorphous phase could stretch across the boundary layer at the electrolyte/electrode interface to come into contact with the carbon surface, thus improving transport of Li⁺ ions by the segmental mobility in polymer.     

Li NMR spectroscopy and ion conduction mechanism of composite gel polymer electrolyte: A comparative study with variation of salt and plasticizer with filler

Microporous composite gel polymer electrolyte (CGPE) has been prepared by incorporating the home-made silica aerogel (SAG) particles into the poly(vinylidene fluoride-co-hexafluoropropylene) (PVdF-HFP) copolymer/LiClO₄ matrix. The ionic transport behavior of the electrolyte is studied with various experimental techniques such as AC impedance, X-ray diffraction (XRD), infrared (IR) spectra, nuclear magnetic resonance (NMR), scanning electron microscopy (SEM), differential scanning calorimetry (DSC) and thermogravimetric analyzer (TGA), etc. The results reveal that the SAG particles are well dispersed in the electrolytes and incorporate with the other components of the CGPEs. The solid-state ⁷Li NMR study has confirmed the interactions of lithium ion with SAG, polymer and plasticizers, causing to form the microporous structure and reduce the glass transition temperature and crystallinity, resulting in an increase in ionic conductivity of the CGPE. The best ionic conductivity (1.04 × 10⁻² S/cm at room temperature) is obtained from the composite polymer electrolyte containing 4 wt% of SAG, which is approximately four times higher than the ionic conductivity of the electrolyte without the filler.     

Effect of zwitterionic salt on the electrochemical properties of a solid polymer electrolyte with high temperature stability for lithium ion batteries

In this study, we prepare a kind of solid polymer electrolyte (SPE) based on N-ethyl-N′-methyl imidazolium tetrafluoroborate (EMIBF₄), LiBF₄ and poly(vinylidene difluoride-co-hexafluoropropylene) [P(VdF-HFP)] copolymer. The resultant SPE displays high thermal stability above 300 °C and high room temperature ionic conductivity near to 10⁻³ S cm⁻¹. Its electrochemical properties are improved with incorporation of a zwitterionic salt 1-(1-methyl-3-imidazolium)propane-3-sulfonate (MIm3S). When the SPE contains 1.0 wt% of the MIm3S, it has a high ionic conductivity of 1.57 × 10⁻³ S cm⁻¹ at room temperature, the maximum lithium ions transference number of 0.36 and the minimum apparent activation energy for ions transportation of 30.9 kJ mol⁻¹. The charge-discharge performance of a Li₄Ti₅O₁₂/SPE/LiCoO₂ cell indicates the potential application of the as-prepared SPE in lithium ion batteries.     

Effect of surface modified porous inorganic-organic hybrid polyphosphazene nanotubes on the properties of polyethylene oxide based solid polymer electrolytes

2-(2-methyloxyethoxy)ethanol modified poly (cyclotriphosphazene-co-4,4′-sufonyldiphenol) (PZS) nanotubes were synthesized and solid composite polymer electrolytes based on the surface modified polyphosphazene nanotubes added to PEO/LiClO₄ model system were prepared. Differential Scanning Calorimetry (DSC) and Scanning Electron Microscopy (SEM) were used to investigate the characteristics of the composite polymer electrolytes (CPE). The ionic conductivity, lithium ion transference number and electrochemical stability window can be enhanced after the addition of surface modified PZS nanotubes. The electrochemical investigation shows that the solid composite polymer electrolytes incorporated with PZS nanotubes have higher ionic conductivity and lithium ion transference number than the filler SiO₂. Maximum ionic conductivity values of 4.95 × 10⁻⁵ S cm⁻¹ at ambient temperature and 1.64 × 10⁻³ S cm⁻¹ at 80 °C with 10 wt % content of surface modified PZS nanotubes were obtained and the lithium ion transference number was 0.41. The good chemical properties of the solid state composite polymer electrolytes suggested that the inorganic-organic hybrid polyphosphazene nanotubes had a promising use as fillers in solid composite polymer electrolytes and the PEO₁₀-LiClO₄-PZS nanotubes solid composite polymer electrolyte can be used as a candidate material for lithium polymer batteries.     

The conductivity and characterization of the plasticized polymer electrolyte based on the P(AN-co-GMA-IDA) copolymer with chelating group (II): The effect of free ion in the plasticized polymer electrolyte

A new gel-type polymer electrolyte (GPE) was made by the copolymerizing acrylonitrile (AN) and (2-methylacrylic acid 3-(bis-carboxymethylamino)-2-hydroxy-propyl ester) (GMA-IDA). The copolymer mixed with a plasticizer—propylene carbonate (PC) and lithium salt to form GPE. The lithium salts are LiCF₃SO₃, LiBr and LiClO₄. FT-IR spectra show that the lithium ion in the LiClO₄ system has the strongest interaction with the group based on the plasticized polymer. FT-IR spectra also indicate that CF₃SO₃⁻ prefers producing anion-cation association. Moreover, the ¹³C solid state NMR spectra for the carbons attached to the PC of GPE exhibited different level of chemical shift (158.5 ppm) when the different lithium salts were added to the electrolyte. The results of differential scanning calorimeter (DSC) also indicate that the LiClO₄ system has more free lithium ions; therefore, it has the maximum conductivity. In this study, the highest conductivity 2.98 × 10⁻³ S cm⁻¹ exists in AG2/PC = 20/80 wt.% system which contain 3 mmole (g-polymer)⁻¹ LiClO₄. Additionally, the polymer electrolytes, which contain GMA-IDA have better interfacial resistance stability with lithium electrode.     

1-Alkyl-2,3-dimethylimidazolium bis(trifluoromethanesulfonyl)imide ionic liquids as highly safe electrolyte for Li/LiFePO4 battery

Several 1-alkyl-2,3-dimethylimidazolium bis(trifluoromethanesulfonyl)imide ionic liquids (alkyl-DMimTFSI) were prepared by changing carbon chain lengths and configuration of the alkyl group, and their electrochemical properties and compatibility with Li/LiFePO₄ battery electrodes were investigated in detail. Experiments indicated the type of ionic liquid has a wide electrochemical window (−0.16 to 5.2 V vs. Li⁺/Li) and are theoretically feasible as an electrolyte for batteries with metallic lithium as anode. Addition of vinylene carbonate (VC) improves the compatibility of alkyl-DMimTFSI-based electrolytes towards lithium anode and LiFePO₄ cathode, and enhanced the formation of solid electrolyte interface to protect lithium anodes from corrosion. The electrochemical properties of the ionic liquids obviously depend on carbon chain length and configuration of the alkyl, including ionic conductivity, viscosity, and charge/discharge capacity etc. Among five alkyl-DMimTFSI-LiTFSI-VC electrolytes, Li/LiFePO₄ battery with the electrolyte-based on amyl-DMimTFSI shows best charge/discharge capacity and reversibility due to relatively high conductivity and low viscosity, its initial discharge capacity is about 152.6 mAh g⁻¹, which the value is near to theoretical specific capacity (170 mAh g⁻¹). Although the battery with electrolyte-based isooctyl-DMimTFSI has lowest initial discharge capacity (8.1 mAh g⁻¹) due to relatively poor conductivity and high viscosity, the value will be dramatically added to 129.6 mAh g⁻¹ when 10% propylene carbonate was introduced into the ternary electrolyte as diluent. These results clearly indicates this type of ionic liquids have fine application prospect for lithium batteries as highly safety electrolytes in the future.     

A polymeric solid electrolyte based on a binary blend of poly(ethylene oxide), poly(methyl vinyl ether-maleic acid) and LiClO4

A new polymeric solid electrolyte based on a PEO/PMVE-MAc blend, complexed with LiClO₄, was obtained and characterized by differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), polarized light optical microscopy, electrochemical impedance and cyclic voltammetry. DSC traces indicated miscibility for all the PSE samples. Crystallinity was suppressed for samples with LiClO₄ concentrations higher than 2.5 wt%. FTIR associated with DSC studies indicated that there is a preferential formation of complexes PEO/Li⁺/PMVE-MAc in all PSE samples studied here. The ionic conductivity of PSE reaches a maximum of about 10⁻⁵ S/cm at ambient temperature and 7.5 wt% LiClO₄. The electrochemical stability window is 4.5 V and associated with the other characteristics, make the PSE studied here suitable for applications in ‘smart-windows’, batteries, sensors, etc.     

Influence of ionic additives NaI/I2 on the properties of polymer gel electrolyte and performance of quasi-solid-state dye-sensitized solar cells

The ionic additives NaI/I₂ in polymer gel electrolyte not only provide cations, but also affect the liquid electrolyte absorbency of the poly(acrylic acid)-poly(ethylene glycol) hybrid, which results in the change of ionic conductivity of polymer gel electrolyte and the photovoltaic performance of quasi-solid-state dye-sensitized solar cell. With the optimized components of liquid electrolyte containing 0.5 M NaI, 0.05 M I₂, 0.4 M pyridine, 70 vol.% γ-butyrolactone and 30 vol.% N-methylpyrrolidone, a 4.74% power conversion efficiency of quasi-solid-state dye-sensitized solar cell was obtained under 100 mW cm⁻² (AM 1.5) irradiation.     

Relationship between glass network structure and conductivity of Li2O-B2O3-P2O5 solid electrolyte

Solid state glass electrolyte, xLi₂O-(1 − x)(yB₂O₃-(1 − y)P₂O₅) glasses were prepared with wide range of composition, i.e. x = 0.35 - 0.5 and y = 0.17 - 0.67. This material system is one of the parent compositions for chemically and electrochemically stable solid-state electrolyte applicable to thin film battery. Lithium ion conductivity of Li₂O-B₂O₃-P₂O₅ glasses was studied in the correlation to the structural variation of glass network by using FTIR and Raman spectroscopy. The measured ionic conductivity of the electrolyte at room temperature increased with x and y. The maximum conductivity of this glass system was 1.6 × 10⁻⁷ Ω⁻¹ cm⁻¹ for 0.45Li₂O-0.275B₂O₃-0.275P₂O₅ at room temperature. It was shown that the addition of P₂O₅ reduces the tendency of devitrification and increases the maximum amount of Li₂O added into glass former without devitrification. As Li₂O and B₂O₃ contents increased, the conductivity of glass electrolyte increased due to the increase of three-coordinated [BO₃] with a non-bridging oxygen (NBO).     

Ionic conductivity in polyethylene-b-poly(ethylene oxide)/lithium perchlorate solid polymer electrolytes

The ionic conductivity and phase arrangement of solid polymeric electrolytes based on the block copolymer polyethylene-b-poly(ethylene oxide) (PE-b-PEO) and LiClO₄ have been investigated. One set of electrolytes was prepared from copolymers with 75% of PEO units and another set was based on a blend of copolymer with 50% PEO units and homopolymers. The differential scanning calorimetry (DSC) results, for electrolytes based on the copolymer with 75% of PEO units, were dominated by the PEO phase. The PEO block crystallinity dropped and the glass transition increased with salt addition due to the coordination of the cation by PEO oxygen. The conductivity for copolymers 75% PEO-based electrolyte with 15 wt% of salt was higher than 10⁻⁵ S/cm at room temperature and reached to 10⁻³ S/cm at 100 °C on a heating measurement. The blend of PE-b-PEO (50% PEO)/PEO/PE showed a complex thermal behavior with decoupled melting of the blocks and the homopolymers. Upon salt addition the endotherms associated with PEO domains disappeared and the PE crystals remained untouched. The conductivity results were limited at 100 °C to values close to 10⁻⁴ S/cm and at room temperature values close to 3 × 10⁻⁶ S/cm were obtained for the 15 wt% salt electrolyte. Raman study showed that the ionic association of the highly concentrated blend electrolytes at room temperature is not significant. Therefore, the lower values of conductivity in the case of the blend with 50% PEO can be assigned to the higher content of PE domains leading to a morphology with lower connectivity for ionic conduction both in the crystalline and melted state of the PE domains.     

Polymer electrolytes based on a ternary miscible blend of poly(ethylene oxide), poly(bisphenol A-co-epichlorohydrin) and poly(vinyl ethyl ether)

Ternary blends of poly(ethylene oxide) (PEO), poly(bisphenol A-co-epichlorohydrin) (PBE) and poly(vinyl ethyl ether) (PVEE) were obtained as films and characterized by differential scanning calorimetry (DSC) and vibrational spectroscopy (FTIR). From the DSC results, phase diagrams for the ternary blends were determined, where the variation of the viscoelastic phase extent as a function of the polymers composition was determined. The DSC results also indicated miscibility of the system, exhibiting only one glass transition temperature (T_g) and decrease in the crystallinity of the system, as well as decrease in the crystallinity of PEO present in the blends. Vibrational spectroscopy (FTIR) provided information on the intermolecular interactions between the pairs PBE/PEO and PBE/PVEE, via hydrogen bond interaction. From the FTIR analyses, molecular model systems of equilibrium among the interacting structures were proposed as a molecular basis for the miscibility of the system.Polymer electrolytes based on the ternary blend containing 60/25/15 (PEO/PBE/PVEE) mass percent and lithium perchlorate (LiClO₄) were obtained and characterized by DSC, FTIR, optical microscopy and electrochemical impedance spectroscopy (EIS). Solid electrolytes containing up to 10 wt% LiClO₄ exhibited a single-phase behavior, evidenced by the DSC results. For these electrolytes, FTIR spectra indicated the formation of polymer-ion complexes, in which the cation (Li⁺) acts favoring the polymer-polymer miscibility. Electrolytes containing LiClO₄ higher than 10 wt% exhibit a multiple phase behavior, in which a PEO-rich, salt-containing phase is present in equilibrium with PBE or PVEE-rich phases. Maximum ionic conductivity at room temperature, for the electrolyte containing 20 wt% LiClO₄, reached 4.23 × 10⁻³ Ω⁻¹ cm⁻¹, while all samples exhibited conductivity of approximately 10⁻¹ Ω⁻¹ cm⁻¹ at 80 °C.     

Redox induced switching dynamics of a three colour electrochromic metallopolymer film

Thin films of a novel Ru-phenolate based metallopolymer, [Ru(terpy)(box)PVP₂₀]PF₆, in which one in every twenty of the 4-vinyl pyridine monomer units is labelled with the ruthenium complex have been formed on glassy carbon electrodes, terpy is 2,2′:6′,2″-terpyridine, box is 2-(2-hydroxyphenyl)benzoxazole, and PVP is poly(4-vinylpyridine). Cyclic voltammetry and Raman spectroscopy reveal that the Ru^2+/3+ couple is electrochemically reversible but that the phenolate ligand based oxidation is irreversible. These redox processes are associated with reversible colour changes from wine red (reduced) to red orange (mixed composition) then to light green (oxidized) in the visible region and an irreversible change in the near-IR region, respectively. Scanning electron microscopy reveals that repeated switching in LiClO₄ aqueous solution does not induce any significant structural change within the deposit films. Cyclic voltammetry has been used to determine the electrochromic switching rate under semi-infinite linear diffusion conditions. In aqueous LiClO₄, the homogeneous charge transport diffusion coefficient, D_CT, decreases from 3.6 ± 0.3 × 10⁻¹³ to 2.7 ± 0.2 × 10⁻¹³ cm² s⁻¹ as the LiClO₄ concentration increases from 0.1 to 1.0 M. This weak dependence of D_CT on electrolyte concentration suggests that counterion availability is not rate-determining and that the overall rate of charge transport through the metallopolymer film is limited by the rate of segmental polymer chain motion necessary to bring adjacent centres sufficiently close to allow electron transfer to occur. Also the impact of changing the identity of the charge compensating anion of the redox electrochromic switching rate has been investigated. Finally, the electronic conductivity has been determined using interdigitated array electrodes (IDAs).     

Electrochemical properties of novel ionic liquids for electric double layer capacitor applications

An aliphatic quaternary ammonium salt which has a methoxyethyl group on the nitrogen atom formed an ionic liquid (room temperature molten salt) when combined with the tetrafluoroborate (BF₄⁻) and bis(trifluoromethylsulfonyl)imide [TFSI; (CF₃SO₂)₂N⁻] anions. The limiting oxidation and reduction potentials, specific conductivity, and some other physicochemical properties of the novel ionic liquids, N,N-diethyl-N-methyl-N-(2-methoxyethyl)ammonium tetrafluoroborate (DEME-BF₄) and DEME-TFSI have been evaluated and compared with those of 1-ethyl-3-methylimidazolium tetrafluoroborate. DEME-BF₄ is a practically useful ionic liquid for electrochemical capacitors as it has a quite wide potential window (6.0 V) and high ionic conductivity (4.8 mS cm⁻¹ at 25 °C). We prepared an electric double layer capacitor (EDLC) composed of a pair of activated carbon electrodes and DEME-BF₄ as the electrolyte. This EDLC (working voltage ∼2.5 V) has both, a higher capacity above room temperature and a better charge-discharge cycle durability at 100 °C when compared to a conventional EDLC using an organic liquid electrolyte such as a tetraethylammonium tetrafluoroborate in propylene carbonate.     

New mechanism of gas transport at the interface solid/liquid

It was recently shown that an abnormally fast transport of CO molecules takes place at the electrode/electrolyte interface of Pt and PtRu electrodes in H₂SO₄ and HClO₄ solutions. In the present paper, this phenomenon is tested for other gases, such as hydrogen and oxygen. The fast transport is also observed at the solid/electrolyte solution interface of other electrode materials and at the glass/electrolyte interface. Several experiments are shown, demonstrating that mass transfer takes place at a velocity, which is more than one order of magnitude higher than expected for usual diffusion conditions.Assuming radial mass transfer at the interface of a Pt disc, the activation energy, E_a = 23 kJ mol⁻¹, was calculated from Arrhenius plots. The same value was measured in H₂SO₄ and HClO₄ as supporting electrolytes. The mass transport parameter, Y, at 298 K was 4.8 × 10⁻³ cm² s⁻¹ and 2.9 × 10⁻³ cm² s⁻¹ in 0.5 M H₂SO₄ and 1 M HClO₄ respectively.     

Solid-state electrochromic devices with Nb2O5:Mo thin film and gelatin-based electrolyte

A gelatin-based electrolyte has been developed and characterized by impedance spectroscopy, X-ray diffraction, UV-vis-NIR spectroscopy and atomic force microscopy (AFM). The heat treatment temperature was found the key factor affecting its ionic conductivity that increases from 1.5 × 10⁻⁵ S/cm to 4.9 × 10⁻⁴ S/cm by heating from room temperature up to 80 °C. The temperature dependence of the ionic conductivity exhibits an Arrhenius behavior. EC-devices with the configuration K-glass/Nb₂O₅:Mo EC-layer/gelatin-based electrolyte/(CeO₂)_x(TiO₂)_1−x ion-storage (IS) layer/K-glass, have been assembled and characterized. They show a good long time cyclic stability, but the change of the optical density measured at 550 nm after 25 000 cycles was only 0.13.     

Nano-size LiAlO2 ceramic filler incorporated porous PVDF-co-HFP electrolyte for lithium-ion battery applications

The optimized composition of PVdF-co-HFP-LiAlO₂ based micro-porous nano-composite polymer electrolyte membranes (MPNCPEMs) was prepared with a preferential polymer dissolution process. Nitrogen adsorption isotherms and SEM micrographs showed that the enhanced ionic conductivity of polymer electrolyte was due to increase in pore-size, surface area and pore density, results an increase in the electrolyte uptake. The ac-impedance spectroscopy showed that the room temperature ionic conductivity of PVdF-co-HFP-LiAlO₂ based polymer electrolyte membranes increased with the removal of PVA content and attained the maximum ionic conductivity of 8.12 × 10⁻³ S cm⁻¹. The prepared MPNCPEM of high ionic conductivity was subjected into LSV study. Finally, the electrode/electrolyte interfacial resistance was evaluated by monitoring the impedance response at different time intervals.