Voltammetric studies of a cobalt(II)-4-methylsalophen modified carbon-paste electrode and its application for the simultaneous determination of cysteine and ascorbic acid

A carbon-paste electrode (CPE) chemically modified with the cobalt(II)-4-methylsalophen (CoMSal) as a Schiff base complex was used as a highly sensitive and fairly selective electrochemical sensor for simultaneous determination of minor mounts of ascorbic acid (AA) and cysteine. This modified electrode shows very efficient electrocatalytic activity for anodic oxidation of both AA and cysteine via substantially decreasing of anodic overpotentials for both compounds. The mechanism of electrochemical oxidation of both AA and cysteine using CoMSal-modified electrode was thoroughly investigated by cyclic voltammetry and polarization studies. Results of cyclic voltammetry (CV) and differential pulse voltammetry (DPV) using this modified electrode show two well-resolved anodic waves for the oxidation of AA and cysteine, which makes it possible for simultaneous determination of both compounds. A linear range of 1 × 10⁻⁴ to 5 × 10⁻⁷ M for cysteine in a constant concentration of 1 × 10⁻⁴ M AA in buffered solution (as a background electrolyte) was obtained from DPV measurements using this electrode. The linear range, which is obtained for AA in the presence of 1 × 10⁻⁴ M cysteine, was in the range of 1 × 10⁻⁴ to 1 × 10⁻⁶ M. The modified electrode has good reproducibility (RSD ≤ 2.5%), low detection limit (sub-micromolar) and high sensitivity for the detection of both AA and cysteine with a very high stability in its voltammetric response. Differential pulse voltammetry using the modified electrode exhibited a reasonable recovery for a relatively wide concentration range of cysteine spiked to a synthetic human serum sample.     

Electrocatalytic oxidation and simultaneous determination of uric acid and ascorbic acid on the gold nanoparticles-modified glassy carbon electrode

A new gold nanoparticles-modified electrode (GNP/LC/GCE) was fabricated by self-assembling gold nanoparticles to the surface of the l-cysteine-modified glassy carbon electrode. The modified electrode showed an excellent character for electrocatalytic oxidization of uric acid (UA) and ascorbic acid (AA) with a 0.306 V separation of both peaks, while the bare GC electrode only gave an overlapped and broad oxidation peak. The anodic currents of UA and AA on the modified electrode were 6- and 2.5-fold to that of the bare GCE, respectively. Using differential pulse voltammetry (DPV), a highly selective and simultaneous determination of UA and AA has been explored at the modified electrode. DPV peak currents of UA and AA increased linearly with their concentration at the range of 6.0 × 10⁻⁷ to 8.5 × 10⁻⁴ mol L⁻¹ and 8.0 × 10⁻⁶ to 5.5 × 10⁻³ mol L⁻¹, respectively. The proposed method was applied for the detection of UA and AA in human urine with satisfactory result.     

Investigation of photoelectrocatalytic activity of Cu2O nanoparticles for p-nitrophenol using rotating ring-disk electrode and application for electrocatalytic determination

A cuprous oxide (Cu₂O) nanoparticles modified Pt rotating ring-disk electrode (RRDE) was successfully fabricated, and the electrocatalytic determination of p-nitrophenol (PNP) using this electrode was developed. Cu₂O nanoparticles were obtained by reducing the copper-citrate complex with hydrazine hydrate (N₂H₄·H₂O) in a template-free process. The hydrodynamic differential pulse voltammetry (HDPV) technique was applied for in situ monitor the photoelectrochemical behavior of PNP under visible light using nano-Cu₂O modified Pt RRDE as working electrode. PNP undergoes photoelectrocatalytic degradation on nano-Cu₂O modified disk to give electroactive p-hydroxylamino phenol species which is compulsive transported and can only be detected at ring electrode at around 0.05 V with oxidation signal. The effects of illumination time, applied bias potential, rotation rates and pH of the reaction medium have been discussed. Under optimized conditions for electrocatalytic determination, the anodic current is linear with PNP concentration in the range of 1.0 × 10⁻⁵ to 1.0 × 10⁻³ M, with a detection limit of 1.0 × 10⁻⁷ M and good precision (RSD = 2.8%, n = 10). The detection limit could be improved to 1.0 × 10⁻⁸ M by given illumination time. The proposed nano-Cu₂O modified RRDE can be potentially applied for electrochemical detection of p-nitrophenol. And it also indicated that modified RRDE technique is a promising way for photoelecrocatalytic degradation and mechanism analysis of organic pollutants.     

Determination of picomolar silver concentrations by differential pulse anodic stripping voltammetry at a carbon paste electrode modified with phenylthiourea-functionalized high ordered nanoporous silica gel

This study introduces the design of an anodic stripping voltammetric (ASV) method for the silver ion determination at a carbon paste electrode (CPE), chemically modified with phenylthiourea-nanoporous silica gel (Tu-SBA-15-CPE). The electroanalytical pro includes two steps: preconcentration of metal ions at an electrode surface, followed by quantification of the accumulated species by differential pulse anodic stripping voltammetric methods. Factors affecting the performance of the anodic stripping were investigated, including the modifier quantity in the paste, the electrolyte concentrations, the solution pH and the accumulation potential or time. The most sensitive and reliable electrode contained 10% Tu-SBA-15 and 90% carbon paste. The accumulation potential and time were set at, −200 mV and 300 s, respectively, and the scan rate at 50 mV s⁻¹ in the scan range of −200 to 700 mV. The resulting electrode demonstrated a linear response over range of silver ion concentration of 8.0-80 pmol/L with detection limit (S/N = 3) of 5 pmol/L. The prepared electrodes were used for the silver determination in sea and tap water samples and very good recovery results were obtained. The accuracy was assessed through recovery experiments and independent analysis by graphite furnace atomic absorption spectrometry.     

Structural and electrochemical characterization of a cobalt phthalocyanine bulk-modified SiO2/SnO2 carbon ceramic electrode

A cobalt phthalocyanine bulk-modified carbon ceramic composite has been prepared by using sol-gel processing, and characterized by BET surface area, X-ray photoelectron spectroscopy, scanning electron microscopy and atomic force microscopy. A water-soluble 3-n-propylpyridinium chloride silsesquioxane (SiPyCl), an ion exchanger polymer, was employed to attach cobalt(II) tetrasulfophthalocyanine (CoTsPc) and prevent its leakage, as well as, to ensure adequate dispersion in the sol-gel network. The modified electrode built in a rigid disk-format displayed good electrocatalytic behavior towards the oxidation of oxalic acid at 0.84 V (SCE), as evidenced by the enhancement of the anodic current peak intensity when the concentration of oxalic acid was increased. A linear response was found in the range of 1.6 × 10⁻⁵ to 1.5 × 10⁻³ mol l⁻¹ with a detection limit of 7.1 × 10⁻⁶ mol l⁻¹.     

Voltammetric determination of ascorbic acid and dopamine in the same sample at the surface of a carbon paste electrode modified with polypyrrole/ferrocyanide films

Functionalized polypyrrole film were prepared by incorporation of [Fe(CN)₆]⁴⁻ as a doping anion, during the electropolymerization of pyrrole onto a carbon paste electrode in an aqueous solution by potentiostatic method. The electrochemical behavior of dopamine (DA) and ascorbic acid (AA) in one solution was studied at the surface of bare and modified carbon paste electrodes using cyclic voltammetry (CV), linear sweep voltammetry (LSV) and differntial pulse voltammetry (DPV) methods. The well separated anodic peaks for oxidation of DA and AA were observed at the surface of the modified carbon paste electrode under optimum condition (pH 6.00), which can be used for determination of these species simultaneously in mixture by LSV and DPV methods. The linear analytical curves were obtained in the ranges of 0.10-1.00 mM and 0.10-0.95 mM for ascorbic acid and 0.10-1.20 mM and 0.20-0.95 mM for dopamine concentrations using LSV and DPV methods, respectively. The detection limits (2σ) were determined as 3.38 × 10⁻⁵ M and 1.34 × 10⁻⁵ M of ascorbic acid and 3.86 × 10⁻⁵ M and 1.51 × 10⁻⁵ M of dopamine by CV and DPV methods.     

Microwave-polyol synthesis of nanocrystalline ruthenium oxide nanoparticles on carbon nanotubes for electrochemical capacitors

The ruthenium oxide nanoparticles dispersed on multi-wall carbon nanotubes (CNTs) were successfully synthesized via microwave-polyol process combined with forced hydrolysis without additional thermal oxidation or electrochemical oxidation treatment. The HRTEM, Raman spectra and TGA curve indicate that CNTs were uniformly coated with crystalline and partially hydrous RuO₂·0.64H₂O nanoparticles of 2 nm diameter and the loading amount of ruthenium oxide in the composite could be controlled up to 70 wt.%. The specific capacitance was 450 Fg⁻¹ of ruthenium oxide/CNT composite electrode with 70 wt.% ruthenium oxide at the potential scan rate of 10 mV s⁻¹ and it decreased to 362 Fg⁻¹ by 18% at 500 mV s⁻¹. The specific capacitance of ruthenium oxide in the composite was 620 Fg⁻¹ of ruthenium oxide at 10 mV s⁻¹. The ruthenium oxide nanoparticles in ruthenium oxide/CNT nanocomposite electrode had a high ratio of outer charge to total charge of 0.81, which confirmed its high-rate capability of the composite through the preparation of the nano-sized ruthenium oxide particles on the external surface of CNTs.     

Electrocatalytic hydrazine oxidation on quinizarine modified glassy carbon electrode

The electrocatalytic oxidation of hydrazine has been studied on glassy carbon modified by electrodeposition of quinizarine, using cyclic voltammetry and chronoamperometry techniques. It has been shown that the oxidation of hydrazine to nitrogen occurs at a potential where oxidation is not observed at the bare glassy carbon electrode. The apparent charge transfer rate constant and transfer coefficient for electron transfer between the electrode surface and immobilized quinizarine were calculated as 4.44 s⁻¹ and 0.66, respectively. The heterogenous rate constant for oxidation of hydrazine at the quinizarine modified electrode surface was also determined and found to be about 4.83 × 10³ M⁻¹ s⁻¹. The diffusion coefficient of hydrazine was also estimated as 1.1 × 10⁻⁶ cm² s⁻¹ for the experimental conditions, using chronoamperometry.     

Electrocatalytic oxidation of ascorbic acid by [Fe(CN)6] redox couple electrostatically trapped in cationic N,N-dimethylaniline polymer film electropolymerized on diamond electrode

Multinegatively charged metal complex, hexacyanoferrate ([Fe(CN)₆]⁴⁻), was electrostatically trapped in the cationic polymer film of N,N-dimethylaniline (PDMA) which was electrochemically deposited on the boron-doped diamond (BDD) electrode by controlled-potential electro-oxidation of the monomer. This ferrocyanide-trapped PDMA film was used to catalyze the oxidation of ascorbic acid (AA). Increase in the oxidation current response with a negative shift of the anodic peak potential was observed at the cationic PDMA film-coated BDD (PDMA|BDD) electrode, compared with that at the bare BDD electrode. A more drastic enhancement in the oxidation peak current as well as more negative shift of oxidation potential was found at the ferrocyanide-trapped PDMA film-coated BDD ([Fe(CN)₆]^3−/4−|PDMA|BDD) electrode. This [Fe(CN)₆]^3−/4−|PDMA|BDD electrode can be used as an amperometric sensor of AA. Ferrocyanide, electrostatically trapped in the polymer film shows more electrocatalytic activity than that coordinatively attached to the polymer film or dissolved in the solution phase. The electrocatalytic current depends on the surface coverage of ferricyanide, Γ_Fe, within the polymer film. Diffusion coefficient (D) of AA in the solution was estimated by rotating disk electrode voltammetry: D = (5.8 ± 0.3) × 10⁻⁶ cm² s⁻¹. The second-order rate constant for the catalytic oxidation of AA by ferricyanide was also estimated to be 9.0 × 10⁴ M⁻¹ s⁻¹. In the hydrodynamic amperometry using the [Fe(CN)₆]^3−/4−|PDMA|BDD electrode, a successive addition of 1 μM AA caused the successive increase in current response with equal amplitude and the sensitivity was calculated as 0.233 μA cm⁻² μM⁻¹.     

Electrochemical determination of bisphenol A at Mg-Al-CO3 layered double hydroxide modified glassy carbon electrode

The electrochemical behavior of bisphenol A (BPA) was investigated on Mg-Al layered double hydroxide (LDH) modified glassy carbon electrode (GCE) by cyclic voltammetry (CV), differential pulse voltammetry (DPV), linear sweep voltammetry (LSV) and chronocoulometry (CC). The cyclic voltammogram of BPA on the modified electrode exhibited a well defined anodic peak at 0.454 V in 0.1 M pH 8.0 phosphate buffer solution (PBS). The experimental parameters were optimized and the kinetic parameters were investigated. The probable oxidation mechanism was proposed. Under the optimized conditions, the oxidation peak current was proportional to BPA concentration in the range from 1 × 10⁻⁸ to 1.05 × 10⁻⁶ M with the correlation coefficient of 0.9959. The detection limit was 5.0 × 10⁻⁹ M (S/N = 3). The fabricated electrode showed good reproducibility, stability and anti-interference. The proposed method was successfully applied to determine BPA in plastic products and the results were satisfactory.     

Simultaneous voltammetric determination of ascorbic acid, dopamine and uric acid by methylene blue adsorbed on a phosphorylated zirconia-silica composite electrode

This paper describes the preparation, characterization and application of a composite electrode based on methylene blue adsorption to phosphorylated zirconia-silica mixed oxide particles prepared by a sol-gel process. This electrode electrocatalytically oxidizes ascorbic acid (AA), dopamine (DA) and uric acid (UA), allowing their simultaneous voltammetric detection. Well-defined and -separated oxidation peaks were observed by differential pulse voltammetry in a 0.35 mol l⁻¹ Tris-HCl buffer solution (pH 7.4) containing 0.5 mol l⁻¹ KCl. The anodic peak currents observed at −74, 94 and 181 mV increased with increasing concentrations of AA, DA and UA, respectively. Linear calibration plots were obtained over the range of 100-1600 μmol l⁻¹ for ascorbic acid, 6-100 μmol l⁻¹ for dopamine and 22-350 μmol l⁻¹ for uric acid with detection limits of 8.3 ± 0.1, 1.7 ± 0.1 and 3.7 ± 0.2 μmol l⁻¹, respectively. DA and UA concentrations could also be determined under conditions of excess AA (1 mmol l⁻¹).     

Electrochemical sensor for sulfite determination based on a nanostructured copper-salen film modified electrode

The electrochemical preparation described herein involved the electrocatalytic oxidation of sulfite on a platinum electrode modified with nanostructured copper salen (salen = N,N′-ethylenebis(salicylideneiminato)) polymer films. The complex was prepared and electropolymerized at a platinum electrode in a 0.1 mol L⁻¹ solution of tetrabutylammonium perchlorate in acetonitrile by cyclic voltammetry between 0 and 1.4 V vs. SCE. After cycling the modified electrode in a 0.50 mol L⁻¹ KCl solution, the estimated surface concentration was found to be equal to 2.2 × 10⁻⁹ mol cm⁻². This is a typical behavior of an electrode surface immobilized with a redox couple that can usually be considered as a reversible single-electron reduction/oxidation of the copper(II)/copper(III) couple. The potential peaks of the modified electrode in the electrolyte solution (aqueous) containing the different anions increase with the decrease of the ionic radius, demonstrating that the counter-ions influence the voltammetric behavior of the sensor. The potential peak was found to be linearly dependent upon the ratio [ionic charge]/[ionic radius]. The oxidation of the sulfite anion was performed at the platinum electrode at +0.9 V vs. SCE. However, a significant decrease in the overpotential (+0.45 V) was obtained while using the sensor, which minimized the effect of oxidizable interferences. A plot of the anodic current vs. the sulfite concentration for chronoamperometry (potential fixed = +0.45 V) at the sensor was linear in the 4.0 × 10⁻⁶ to 6.9 × 10⁻⁵ mol L⁻¹ concentration range and the concentration limit was 1.2 × 10⁻⁶ mol L⁻¹. The reaction order with respect to sulfite was determined by the slope of the logarithm of the current vs. the logarithm of the sulfite concentration.     

Adsorption of phosphate species on poly-oriented Pt and Pt(1 1 1) electrodes over a wide range of pH

The adsorption of phosphate anions from phosphate solutions at poly-oriented and single-crystal platinum electrodes, primarily Pt(1 1 1), was studied over a wide range of pH by cyclic voltammetry. The features observed at the poly-oriented Pt electrode in phosphate solution may be related to the different crystalline facets, the (1 1 1) orientation presenting the most significant behavior in terms of phosphate adsorption. On the reversible hydrogen electrode (RHE) scale, the phosphate adsorption strength decreases with increasing alkalinity of the solution. Qualitatively, three different pH regions can be distinguished. At pH < 6 only a broad reversible peak is observed, corresponding to the adsorption of H₂PO₄⁻ and further deprotonation to adsorbed HPO₄⁻. For 6 < pH < 11 a butterfly feature followed by one or two anodic peaks (depending on scan rate) is observed, ascribed to the adsorption of HPO₄⁻ followed by its subsequent deprotonation to adsorbed PO₄³⁻. The splitting into two or three voltammetric features, and the irreversibility of the two features at more positive potential, is ascribed to the deprotonation reaction leading to a surface species (i.e. phosphate) which needs to change its surface coordination. At pH > 11 a reversible pre-wave and a sharp spike are observed, ascribed to the co-adsorption of phosphate and hydroxide.     

Electrochemical behaviors of thymine on a new ionic liquid modified carbon electrode and its detection

A new electrochemical method was proposed for the determination of thymine, which relied on the oxidation of thymine at a carbon ionic liquid electrode (CILE) in a pH 5.0 Britton-Robinson buffer solution. CILE was fabricated by using ionic liquid 1-(3-chloro-2-hydroxy-propyl)-3-methylimidazole acetate as the binder, which showed strong electrocatalytic ability to promote the oxidation of thymine. A single well-defined irreversible oxidation peak appeared with adsorption-controlled process and enhanced electrochemical response on the CILE, which was due to the presence of high conductive ionic liquid on the electrode. The reaction parameters of thymine were calculated with the electron transfer coefficient (α) as 0.27, the electron transfer number (n) as 1.23, the apparent heterogeneous electron transfer rate constant (k_s) as 6.87 × 10⁻⁶ s⁻¹ and the surface coverage (Г_T) as 5.71 × 10⁻⁸ mol cm⁻². Under the selected conditions the oxidation peak current was proportional to thymine concentration in the range from 3.0 to 3000.0 μM with the detection limit as 0.54 μM (3σ) by differential pulse voltammetry. The proposed method showed good selectivity to the thymine detection without the interferences of coexisting substances.     

A voltammetric and nanogravimetric study of Te underpotential deposition on Pt in perchloric acid medium

This work describes the study of Te underpotential deposition on Pt in acid media using cyclic voltammetry, rotating ring-disc electrode and electrochemical quartz crystal microbalance techniques. The voltammetric results indicate the presence of two dissolution peaks in the positive scan with a total charge density of 420 μC cm⁻². These phenomena are attributed to the deposition of one Te monolayer with the occupancy of two active Pt sites by each ad-atom. This is confirmed by rotating ring-disc electrode results. The electrochemical quartz crystal microbalance (EQCM) experiments yielded the small mass variation of −32 ng cm⁻² (while the theoretical one is −140.4 ng cm⁻² for a complete Te monolayer). This low value can be attributed to the simultaneous adsorption of water, perchlorate anions and the formation of platinum oxide.     

Effects of complex agents on the anodic deposition and electrochemical characteristics of cobalt oxides

The anodic deposition rate of cobalt oxide from CoCl₂·6H₂O is strongly affected by the type of complex agents (acetate ion (AcO⁻), citrate ion, EDTA) added into the deposition solutions. The oxidation potential of CoCl₂·6H₂O, examined by linear sweep voltammetry (LSV), is negatively shifted from ca. 1.1 V to about 0.8, 0.5, and 0.2 V by adding AcO⁻, citrate ion, and EDTA, respectively. The deposition rate of cobalt oxide is found to depend not only on the coordinating strength between Co and ligands but also on the conversion rate of the Co-L complexes (L: ligand) into the oxy-hydroxyl-Co species after electron transfer. The textural and electrochemical characteristics of resultant Co oxides, examined by X-ray photoelectron spectroscopic (XPS), scanning electron microscopic (SEM), open-circuit potential versus time, and cyclic voltammetric analyses, are also influenced by varying the complex agents. The deposition rate is the highest when the Co oxide is deposited from the precursor solution containing AcO⁻, which also exhibits the highest specific capacitance of ca. 230 F g⁻¹ among all Co oxide deposits (as the oxide loading ≥0.05 mg cm⁻²), demonstrating its most promising applicability in the electrochemical supercapacitors.     

In situ FTIRS and EQCM studies of glycine adsorption and oxidation on Au(1 1 1) electrode in alkaline solutions

Dissociative adsorption and oxidation of glycine on Au(1 1 1) single crystal electrodes in alkaline solutions were studied in the present paper using cyclic voltammetry (CV), in situ FTIR spectroscopy (FTIRS) and electrochemical quartz crystal microbalance (EQCM). In situ FTIRS results demonstrated that adsorbates derived from glycine dissociative adsorption are adsorbed cyanide anions (CN_ad⁻). The CN_ad⁻ species are stable on Au(1 1 1) surface in the potential region from −0.8 to 0.0 V, and can be oxidized when electrode potential is increased above 0.1 V. The oxidation of CN_ad⁻ releases surface active sites for further glycine oxidation. The products of CN_ad⁻ oxidation were determined by in situ FTIRS as cyanate (OCN⁻), aurous cyanide (AuCN) and aurous di-cyanide (Au(CN)₂⁻). The formation of Au(CN)₂⁻ may initiate a dissolution of Au(1 1 1) surface atoms, which has been confirmed by a loss of surface mass determined in EQCM studies. It has revealed also that at high electrode potential region glycine may be split on Au(1 1 1) surface to form AuCH₂NH₂ and AuCOO⁻ adsorbates. Further oxidation of these species yielded CO₂ and -NH₂, and the AuCH₂NH₂ may be also combined with surface Au oxide to form methylamine. The CO₂ species produced in glycine oxidation are all retained in alkaline solutions to generate carbonate (CO₃²⁻) and bicarbonate (HCO₃⁻) species that were clearly determined by in situ FTIRS studies.     

Voltammetric determination of bisoprolol fumarate in pharmaceutical formulations and urine using single-wall carbon nanotubes modified glassy carbon electrode

The electrochemistry of bisoprolol fumarate (BF) has been investigated by differential pulse voltammetry at a single-wall carbon nanotubes (SWNTs) modified glassy carbon electrode (GCE). The prepared electrode showed an excellent electrocatalytic activity towards the oxidation of BF leading to a marked improvement in sensitivity as compared to bare glassy carbon electrode where electrochemical activity for the analyte cannot be observed. The SWNTs-modified GCE exhibited a sharp anodic peak at a potential of ∼950 mV for the oxidation of BF. Under optimum conditions linear calibration curve was obtained over the BF concentration range 0.01-0.1 mM in 0.5 M phosphate buffer solution (pH 7.2) with a correlation coefficient of 0.9789 and detection limit of 8.27 × 10⁻⁷ M. The modified electrode has been applied for the drug determination in human urine with no prior extraction and in commercial tablets. The proposed method has also been validated.     

Synthesis, characterization and electroanalytical application of a new SiO2/SnO2 carbon ceramic electrode

A new SiO₂/SnO₂ carbon ceramic composite was prepared by the sol-gel method, and its potential application in electrochemistry as a novel electrode material has been studied. The prepared xerogel was structurally and electrochemically characterized by scanning electron microscopy coupled to energy dispersive spectroscopy, X-ray photoelectron spectroscopy, X-ray diffraction and cyclic voltammetry. The composite was pressed in a rigid disk-shape and used as a conductive substrate to immobilize a water-soluble organic-inorganic hybrid polymer, 3-n-propyl-4-picolinium chloride silsesquioxane. The oxidation of nitrite was studied on this polymer film coated electrode in aqueous solution using cyclic voltammetry and differential pulse voltammetry. This modified electrode exhibited a better defined voltammetric peak shifted negatively about 60 mV. The linear detection limit found for nitrite was from 1.3 × 10⁻⁵ to 1.3 × 10⁻³ mol l⁻¹ and the detection limit was 3.3 × 10⁻⁶ mol l⁻¹.     

Direct voltammetric determination of gold nanoparticles using graphite-epoxy composite electrode

A new voltammetric method for a direct determination of gold nanoparticles, based on adsorption and electrochemical detection of colloidal gold, is described. In this protocol, the absorption of gold nanoparticles onto the rough surface of graphite-epoxy composite electrode is followed by their electrochemical oxidation in 0.1 M HCl medium at a potential of +1.25 V. The resulting tetrachloroaurate ions generated near the electrode surface are detected by differential pulse voltammetry (DPV). The DPV response is linear in the range from 4.7 × 10⁸ to 4.7 × 10¹¹ nanoparticles cm⁻³ with a limit of detection of 1.8 × 10⁸ gold nanoparticles cm⁻³. The surface characteristics of the composite electrode are investigated and the parameters that affect the complete analytical detection process of gold nanoparticles are optimized.