A highly performing electrochemiluminescent biosensor for glucose based on a polyelectrolyte-chitosan modified electrode

A highly performing ECL glucose biosensor was developed by immobilizing glucose oxidase (GOD) onto a membrane modified glassy carbon electrode, which was prepared by using poly(diallyldimethylammonium chloride) (PDDA) doped with chitosan. In order to obtain the optimal performance of the ECL biosensor, the composition of modified membranes and a series of measurement conditions were investigated. Under the optimal conditions, this ECL biosensor was able to detect glucose in the range of 0.5-4.0 × 10⁴ nM with a detection limit of 0.1 nM (defined as the concentration that could be detected at the signal-to-noise ratio of 3). The relative standard deviation was 0.99% for 5 × 10⁻⁸ mol/L glucose in repetitive measurements in the primary 12 potential cycles. This ECL biosensor offered the effectively improved stability of the electron transfer mediator and exhibited excellent properties for the ultrasensitive and selective determination of glucose with good reproducibility and stability. The present biosensor has also been used to determine the glucose concentrations in real serum samples. The recovery value for the assay of glucose ranged from 96.2 to 107% in the serum samples. The present biosensor displayed both specificity for glucose and retention of signal response even in a complex environment. Therefore, it provided an approach to the sensitive determination of glucose.     

Cathodic electrochemiluminescence of luminol in aqueous solutions based on C-doped oxide covered titanium electrode

In the present work, a novel sensor for luminol electrochemiluminescence (ECL) was constructed on the base of a C-doped titanium oxide amorphous semiconductor electrode. The morphology, structural and electrochemical properties of the electrode was characterized by X-Ray diffraction, X-Ray photoelectron spectroscopy and electrochemical methods. The ECL behavior of luminol excited by hot electrons injected from C-doped oxide film-covered electrodes in aqueous medium has been investigated in B-R buffer solution (pH = 9) when linear sweep cyclic voltammetry (CV) was applied. Two ECL peaks were observed at −1.0 V (vs. Ag/AgCl, reduction process) and −0.75 V (vs. Ag/AgCl, oxidation process). The possible mechanism was discussed. The C-doped Ti oxide electrode shows excellent properties for sensitive determination of luminol with good reproducibility and stability. The linear response of luminol was in the range of 1 × 10⁻⁸ to 9 × 10⁻⁸ mol/L with the detection limit of 3 × 10⁻⁹ mol/L (S/N = 3). Since luminol is one of the most useful ECL probe, many bioactive compounds which can be labeled by luminol are able to be detected by using the proposed method.     

Electrochemiluminescent behavior of luminol on the glassy carbon electrode modified with CoTPP/MWNT composite film

A glassy carbon electrode (GCE) modified with cobalt(II) meso-tetraphenylporphrine/multiwall-carbon nanotube (CoTPP/MWNT) was applied to investigate the electrochemiluminescent (ECL) behavior of luminol. The ECL intensity of luminol was found to be increased greatly on this modified electrode. The presence of cobalt(II) meso-tetraphenylporphrine (CoTPP) can catalyze the reduction of oxygen on the electrode surface to produce HOO⁻, which can increase the ECL intensity of luminol. Moreover, MWNT can provide the more effective area of the electrode, and can act as a promoter to enhance the electrochemical reaction. The proposed method enables a detection limit for luminol of 1.0 × 10⁻⁸ mol/L in the neutral solution. Under the optimum condition, the enhanced ECL intensity of luminol by H₂O₂ had a linear relationship with the concentration of H₂O₂ in the range of 1.0 × 10⁻⁷ to 8.0 × 10⁻⁸ mol/L with the detection limit of 5.0 × 10⁻⁹ mol/L.     

Miscibility of C60‐containing poly(methyl methacrylate)/poly(vinylidene fluoride) blends

The miscibility of C₆₀‐containing poly(methyl methacrylate) (PMMA‐C₆₀) with poly(vinylidene fluoride) (PVDF) was studied. Two PMMA‐C₆₀ samples containing 2.6 and 7.4 wt % C₆₀ were found to be miscible with PVDF based on single glass transition temperature criterion and melting point depression of PVDF. However, the interaction parameters of the two blend systems are less negative than that of the PMMA/PVDF blend system, showing that the incorporation of C₆₀ reduces the ability of carbonyl groups of PMMA to interact with PVDF. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 1393–1396, 2000     

An inelastic electron tunnelling spectroscopy (IETS) study of poly(vinylacetate) poly(methyl methacrylate) and poly(vinylalcohol) adsorbed on aluminium oxide

IETS is used to investigate the adsorption of poly(vinylacetate) (PVA), poly(methylmethacrylate) (PMMA), and poly(vinylalcohol) (PVOH) on aluminium oxide. These polymers are of interest in the field of adhesion science, and until now synthetic macromolecules have not been studied in this way. Both commercially available polymers and those synthesized in our laboratory have been used. On the basis of IET spectra presented here, and existing i.r. spectra it is believed that PMMA and PVA undergo ester cleavage at the oxide surface leading to their subsequent adsorption. For PMMA this is thought to be via carboxylate anions generated on the polymer side groups, while PVA is expected to be adsorbed as PVOH. Bonding of PVOH to the oxide is not fully understood, but may occur by the formation of an AlOC bridge. Another possibility for the above polymers, that of intermolecular hydrogen bonding between polar polymer side groups, and adsorbed hydroxyl species present on the oxide surface, cannot be ruled out.     

Solvent effects on the miscibility of poly(methyl methacrylate)/poly(bisphenol a carbonate) blends

Blends of atactic or syndiotactic poly(methyl methacrylate) (designated as aPMMA or sPMMA) and poly(bisphenol A carbonate) (PC) were prepared from solution casting. Tetrahydrofuran (THF) and chloroform were used as solvent. Experimental results indicated that the as‐cast blends from THF were quite different from the chloroform‐cast ones. After film preparation, THF‐cast blends did not show any visible phase separation. However, chloroform‐cast blends formed a phase‐separated structure. The as‐cast PC from either solvent was not completely amorphous, and had a melting point at 239–242°C, indicating a certain degree of crystallinity. In contrast, the quenched samples of aPMMA/PC blends prepared from the two solvents behaved virtually the same. They both showed aPMMA dissolves better in PC, but PC solubility in aPMMA is very little. Using sPMMA instead of aPMMA to blend with PC, different results were obtained. The quenched sPMMA/PC blends cast from THF showed only one T_g. However, immiscibility (i.e., two T_gs) was found in the same blend system when cast from chloroform. THF was believed to cause the observation of single T_g due to the following kinetic reason. sPMMA and PC were still trapped together even after THF removal in a homogeneous, but nonequilibrium state below the glass transition. Therefore, the quenched sPMMA/PC blends were not truly thermodynamically miscible. From the results of aPMMA or sPMMA with PC, increasing syndiotacticity seemed to improve the miscibility between PMMA and PC. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2842–2850, 2001     

Comparison of the phase behaviour of the liquid-crystalline polymer/poly(methyl methacrylate) and poly(vinyl acetate)/poly(methyl methacrylate) blends

The phase behaviour of blends of a liquid-crystalline polymer (LCP) and poly(methyl methacrylate) (PMMA), as well as the phase state of blends of PMMA and poly(vinyl acetate) (PVA) has been investigated using light scattering and phase-contrast optical microscopy. The blends of LCP and PMMA have been obtained by coagulation from ternary solutions. The cloud point curves were determined. It was established that both pairs demix upon heating, ie have an LCST. In the region of intermediate composition, the phase separation proceeds according to a spinodal mechanism; however for LCP/PMMA blends, the decomposition proceeds according to a non-linear regime from the very onset. In the region of small amounts of LCP, the phase separation follows a mechanism of nucleation and growth. For PMMA/PVA blends, the spinodal decomposition proceeds according to a linear regime, in spite of the molecular mobility that PVA chains develop at lower temperatures. Only after prolonged heat treatment does the process transit to a non-linear regime. The data show a similarity between the phase behaviour of blends of liquid-crystalline and of flexible amorphous polymers. The distinction consists of the absence of a linear regime of decomposition for LCP-PMMA blends. © 1999 Society of Chemical Industry     

Effect of tacticity of poly(methyl methacrylate) on the miscibility with poly(vinyl pyrrolidone)

Isotactic, atactic, and syndiotactic poly(methyl methacrylates) (PMMA) (designated iPMMA, aPMMA, and sPMMA) with approximately the same molecular weight were mixed separately with poly(vinyl pyrrolidone) (PVP) primarily in chloroform to make three polymer blend systems. Differential scanning calorimetry (DSC) was used to study the miscibility of these blends. The results showed that the tacticity of PMMA has a definite impact on its miscibility with PVP. The aPMMA/PVP and sPMMA/PVP blends were found to be miscible because all the prepared films showed composition-dependent glass-transition temperatures (T_g). The glass-transition temperatures of the aPMMA/PVP blends are equal to or lower than weight average and can be qualitatively described by the Gordon–Taylor equation. The glass-transition temperatures of the other miscible blends (i.e., sPMMA/PVP blends) are mostly higher than weight average and can be approximately fitted by the simplified Kwei equation. The iPMMA/PVP blends were found to be immiscible or partially miscible based on the observation of two glass-transition temperatures. The immiscibility is probably attributable to a stronger interaction among isotactic MMA segments because its ordination and molecular packing contribute to form a rigid domain. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 3190–3197, 2001     

Synthesis and thermal properties of poly(methyl methacrylate)‐poly(L‐lactic acid)‐poly(methyl methacrylate) tri‐block copolymer

Poly(methyl methacrylate)‐poly(L ‐lactic acid)‐poly(methyl methacrylate) tri‐block copolymer was prepared using atom transfer radical polymerization (ATRP). The structure and properties of the copolymer were analyzed using infrared spectroscopy, gel permeation chromatography, nuclear magnetic resonance (¹H‐NMR, ¹³C‐NMR), thermogravimetry, and differential scanning calorimetry. The kinetic plot for the ATRP of methyl methacrylate using poly(L ‐lactic acid) (PLLA) as the initiator shows that the reaction time increases linearly with ln[M]₀/[M]. The results indicate that it is possible to achieve grafted chains with well‐defined molecular weights, and block copolymers with narrowed molecular weight distributions. The thermal stability of PLLA is improved by copolymerization. A new wash‐extraction method for removing copper from the ATRP has also exhibits satisfactory results. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis and properties of poly(methyl methacrylate)/montmorillonite (PMMA/MMT) nanocomposites

PMMA/MMT nanocomposites were successfully synthesized via in situ intercalative polymerization, and characterized by means of wide‐angle X‐ray diffractometry, transmission electron microscopy, thermal gravimetric analysis, dynamic mechanical analysis and Fourier‐transform infrared analysis. The nanocomposites possess partially exfoliated and partially intercalated structure, in which the silicate layers are exfoliated into nanometre secondary particles with thickness of less than 20 nm and uniformly dispersed in the polymer matrix. In comparison with pure PMMA, the thermal stability, glass transition temperature, and mechanical properties of the polymer are notably improved by the presence of the nanometric silicate layers. It was found that part of the PMMA chains in the nanocomposites are well immobilized inside and/or onto the layered silicates and, therefore, the unique properties of the nanocomposites result from the strong interactions between the nanometric silicate layers and the polymer chains. Copyright © 2003 Society of Chemical Industry     

Morphological and infra-red studies on highly oriented poly(vinylidene fluoride)/poly(methyl methacrylate) blends

Highly oriented melt drawn films of poly(vinylidene fluoride) (PVDF) and blends of poly(vinylidene fluoride) and poly(methyl methacrylate) (PMMA) have been studied by transmission electron microscopy, electron diffraction and infra-red spectroscopy. Infra-red spectra show the second moment of the orientation function for PVDF samples to be greater than 0.94. Using such a sample, the transition dipole directions relative to the chain axis have been calculated. Electron microscopic studies of the PVDF/PMMA blends show a transformation for pure PVDF from a lamellar morphology to a mixture of lamellar and needle-like crystals for the 80/20 blend. The 60/40 blend shows a pure needle-like morphology. The β phase content for this blend is dependent upon the composition and thermal history. An increase in the β phase content is observed with the addition of PMMA. After annealing at 110°C, the 50/50 blend shows a lamellar β phase morphology. A significant increase in the segmental orientation of PVDF is also observed.     

Investigation on crystallization behavior and hydrophilicity of poly(vinylidene fluoride)/poly(methyl methacrylate)/poly(vinyl pyrrolidone) ternary blends by solution casting

Ternary blends composed of matrix polymer poly(vinylidene fluoride) (PVDF) with different proportions of poly(methyl methacrylate) (PMMA)/poly(vinyl pyrrolidone) (PVP) blends were prepared by solution casting. The crystallization behavior and hydrophilicity of ternary blends were characterized by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), wide angle X‐ray diffraction (WAXD), differential scanning calorimetry (DSC), and contact angle test. According to morphological analysis, the surface was full of typical spherulitic structure of PVDF and the average diameter was in the order of 3 μm. The samples presented predominantly β phase of PVDF by solution casting. It indicated that the size of surface spherulites and crystalline phase had little change with the PMMA or PVP addition. Moreover, FTIR demonstrated special interactions among the ternary polymers, which led to the shift of the carbonyl stretching absorption band of PVP. On the other hand, the melting, crystallization temperature, and crystallinity of the blends had a little change compared with the neat PVDF in the first heating process. Except for the content of PVP containing 30 wt %, the crystallinity of PVDF decreased remarkably from 64% to 33% and the value of t_1/2 was not obtained. Besides, the hydrophilicity of PVDF was remarkably improved by blending with PMMA/PVP, especially when the content of PVP reached 30 wt %, the water contact angle displayed the lowest value which decreased from 98.8° to 51.0°. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

聚苯乙烯-聚甲基丙烯酸甲酯核-壳粒子的制备

由种子乳液聚合法制备了聚苯乙烯-聚甲基丙烯酸甲酯核-壳粒子。以过硫酸钾(KPS)为引发剂,辛基酚聚氧乙烯醚(OP-10)为乳化剂,合成了聚苯乙烯(PS)种子核;连续滴加甲基丙烯酸甲酯(MMA),在核表面富集MMA,制备了粒径范围在0.16~0.67μm的核-壳粒子;当单体苯乙烯与甲基丙烯酸甲酯(St/MMA)的比为30∶70(质量比)时,所得粒径在0.18μm,粒径分布为0.012。差示扫描量热(DSC)研究显示,复合粒子的玻璃化转变温度(Tg)为97.2℃,峰形单一,表现出良好的热性能。     

Crystallization behavior and hydrophilicity of poly(vinylidene fluoride)/poly(methyl methacrylate)/poly(vinyl pyrrolidone) ternary blends

Ternary blends composed of matrix polymer poly(vinylidene fluoride) (PVDF) with different proportions of poly(methyl methacrylate) (PMMA)/poly(vinyl pyrrolidone) (PVP) blends were prepared by melt mixing. The miscibility, crystallization behavior, mechanical properties and hydrophilicity of the ternary blends have been investigated. The high compatibility of PVDF/PMMA/PVP ternary blends is induced by strong interactions between the carbonyl groups of the PMMA/PVP blend and the CF₂ or CH₂ group of PVDF. According to the Fourier transform infrared and wide‐angle X‐ray difffraction analyses, the introduction of PMMA does not change the crystalline state (i.e. α phase) of PVDF. By contrast, the addition of PVP in the blends favors the transformation of the crystalline state of PVDF from non‐polar α to polar β phase. Moreover, the crystallinity of the PVDF/PMMA/PVP ternary blends also decreases compared with neat PVDF. Through mechanical analysis, the elongation at break of the blends significantly increases to more than six times that of neat PVDF. This confirms that the addition of the PMMA/PVP blend enhances the toughness of PVDF. Besides, the hydrophilicity of PVDF is remarkably improved by blending with PMMA/PVP; in particular when the content of PVP reaches 30 wt%, the water contact angle displays its lowest value which decreased from 91.4° to 51.0°. Copyright © 2011 Society of Chemical Industry     

Effect of tacticity of poly(methyl methacrylate) on the miscibility with poly(vinyl acetate)

The results of the miscibility between the chemically similar polymers poly(methyl methacrylate) (PMMA) and poly(vinyl acetate) (PVAc) published so far show inconsistent statements concerning miscibility. The problems may be due to differences in molecular weights, tacticity, and preparation methods of the polymers. This investigation was carried out by using either chloroform or tetrahydrofuran (THF) as solvent to prepare the blends, because to our knowledge, nobody has reported any tacticity effect of PMMA on the miscibility with PVAc. Therefore, in this article, different tactic PMMAs were used to mix with PVAc and their miscibility was studied calorimetrically. The results showed little effect of solvent and tacticity. PMMA and PVAc were determined to be almost completely immiscible because of the observation of two T_g's. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 35–39, 2004     

Mechanical properties of soft liner–poly(methyl methacrylate)‐based denture material

In this study, the mechanical properties of two different permanent soft lining materials and their bonding to poly(methyl methacrylate) (PMMA) were compared. Both of the soft liners were heat‐cured commercial materials. The polymerization was carried out by conventional methods suggested by manufacturer, and the curing was done at the temperature of boiling water for 5, 15, 25, and 35 min. The sample groups were tested in the computer‐aided tensile‐testing machine at a rate of 2 mm/min. The slow rate helps the collection of more and more reliable data. At this time, the stress–strain curves were used to calculate ultimate tensile strength, elastic modulus, resilience, and toughness. The measurements were carried for PMMA, Molloplast B, Flexor, and a combination of PMMA/soft liner. After introducing the soft lining material on PMMA of the same thickness, the new material structure was more elastic than the original PMMA. Flexor showed adhesive failure at studied curing periods, but Molloplast B gave larger tear strength values and cohesive rather than adhesive failure at the 25‐min and 35‐min curing times. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 467–474, 2002     

Evaluating chitosan/β‐tricalcium phosphate/poly(methyl methacrylate) cement composites as bone‐repairing materials

This study related to the preparation of chitosan microspheres by means of reacting chitosan with β‐tricalcium phosphate (β‐TCP) and glutaraldehyde by crosslinking reaction in the oil phase, followed by de‐oil and purification processes to get the product. Three cement composites, Pure P, C1P1, and C2P1, were prepared by the polymerization of poly(methyl methacrylate) (PMMA) bone cement in the presence of 0, 50, and 66.7% chitosan/β‐TCP microspheres, respectively. The result revealed the chitosan/β‐TCP microspheres obtained was in the size range of 50–150 μm. The presence of chitosan/β‐TCP microspheres in the prepared composites decreased the ultimate tensile strength, whereas the modulus remained the same as compared with the commercial PMMA bone cement. Addition of chitosan/β‐TCP microspheres into commercial PMMA cement significantly improved the handling property of the cement paste—that is, the increased setting time and less stickiness behavior of this paste was beneficial, in manipulation, to the operation and easier fittings to the shape and gap of the bony defect and interface. The decreased curing temperature was also less harmful to the surrounding tissues. From scanning electron micrograph observations, chitosan/β‐TCP microspheres can completely mix with bone cement powder and the prepared composites could provide scaffold for osteoblast cells growth and thus improve defects of commercial PMMA bone cement. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3897–3904, 2003     

Effect of organoclay in an immiscible poly(ethylene terephtalate) waste/poly(methyl methacrylate) blend

Blends of organically modified montmorillonite (OMMT) with poly(ethylene terephtalate) (PET) waste and poly(methyl methacrylate) (PMMA) were prepared by melt mixing. The morphology of PET/PMMA nanocomposites with different OMMT contents was characterized by transmission electron microscopy (TEM) and X‐ray diffraction (XRD). The nonisothermal crystallization temperatures of nanocomposites were also examined by DSC. TEM observations and XRD patterns revealed that silicate layers were intercalated and well dispersed in the blend. Nanocomposites displayed better mechanical properties when compared with the unfilled blend. DMA analyses also showed efficient mixing of the two immiscible polymers and changes in glass transition temperature with the presence of OMMT. DSC analysis showed an enhancement in crystallization rate of nanocomposites and a decrease in cristallinity. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Fabrication and morphology control of poly(methyl methacrylate) hollow structures via coaxial electrospinning

A modified electrospinning method known as coaxial electrospinning was used to fabricate poly(methyl methacrylate) (PMMA) hollow structures. In this study to understand morphology control, the effect of processing parameters such as concentration of polymer sheath solution, size of core/sheath capillaries, feed rate, and applied voltage had been evaluated. Morphological observations via scanning electron microscope (SEM) revealed that via the control of polymer concentration within the sheath solution, morphologies such as hollow particles and fibers could be obtained. With the use of fine core/sheath capillaries, micron hollow fibers with walls of less than 20 nm were obtained. This study has demonstrated how the investigated processing parameters have a direct influence on the structures and how these parameters have supported the notion that effective encapsulation process is the key to the dual layer bicomponent structures. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Preparation of cadmium sulfide/poly(methyl methacrylate) composites by precipitation with compressed CO2

Cadmium sulfide (CdS) nanoparticles and poly(methyl methacrylate) (PMMA) were first synthesized in methyl methacrylate (MMA)/sodium bis(2‐ethylhexyl) sulfosuccinate (AOT) microemulsion, in which MMA acts as the solvent and monomer. Then compressed CO₂ was used as an antisolvent to precipitate the CdS and PMMA simultaneously. Using this method, a CdS/PMMA composite was successfully prepared. The CdS nanoparticles dispersed in the polymer matrices were characterized by transmission electron microscopy. The higher pressure is favorable to producing CdS nanoparticles of smaller size. The phase structure of the obtained composite was characterized by X‐ray diffraction, which reveals that cubic CdS particles were formed. The FTIR spectra of the composite showed that there is no chemical bonding or strong interaction between CdS and PMMA. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1643–1648, 2004