Mesoporous polyaniline or polypyrrole/anatase TiO2 nanocomposite as anode materials for lithium-ion batteries

A functional composite as anode materials for lithium-ion batteries, which contains highly dispersed TiO₂ nanocrystals in polyaniline matrix and well-defined mesopores, is fabricated by employing a novel one-step approach. The as-prepared mesoporous polyaniline/anatase TiO₂ nanocomposite has a high specific surface area of 224 m² g⁻¹ and a predominant pore size of 3.6 nm. The electrochemical performance of the as-prepared composite as anode material is investigated by cyclic voltammograms and galvanostatic method. The results demonstrate that the polyaniline/anatase nanocomposite provides larger initial discharge capacity of 233 mAh g⁻¹ and good cycle stability at the high current density of 2000 mA g⁻¹. After 70th cycles, the discharge capacity is maintained at 140 mAh g⁻¹. The excellent electrochemical performance of the polyaniline/TiO₂ nanocomposite is mainly attributed to its special structure. Furthermore, it is accessible to extend the novel strategy to other polymer/TiO₂ composites, and the mesoporous polypyrrole/anatase TiO₂ is also successfully fabricated.     

Ag-TiO2多孔薄膜及其非紫外光辐照下的超亲水特性

采用溶胶凝胶法，以钛酸丁酯为前驱体、硝酸银络合物为银源、聚乙二醇2000（PEG2000）作为结构导向剂，制备超亲水多孔Ag-TiO₂复合薄膜。用X射线衍射仪、X射线光电子能谱仪、扫描电镜、原子力显微镜表征薄膜晶相结构、化学成分以及表面形貌。根据静态水接触角、动态润湿时间、超亲水长效稳定性综合评价不同Ag含量及PEG2000添加量薄膜的超亲水性能。研究发现，掺杂Ag与PEG2000对薄膜在非紫外光下的超亲水特性具有协同作用，掺杂Ag明显提高薄膜动态润湿速度及可见光响应，表面粗糙多孔结构有利于避光条件下的长效超亲水特性。Ag含量10%、PEG2000掺杂量5%的Ag-TiO₂复合薄膜在自然光条件下已具备优良的超亲水性能；水滴0.2 s内即可在表面完全铺展到0°；避光条件下保存，超亲水时效性可达到30 d以上。在可见光活化下即可强化超亲水性能，具有良好的防雾效果。     

Visible light photocatalytic degradation of thiophene using Ag–TiO2/multi-walled carbon nanotubes nanocomposite

Ag–TiO₂ nanocatalyst, supported on multi-walled carbon nanotubes, was synthesized successfully via a modified sol–gel method, and the prepared photocatalyst was used to remediate aqueous thiophene environmentally by photocatalytic oxidation under visible light. The prepared Ag–TiO₂/multi-walled carbon nanotubes nanocomposite photocatalyst was characterized through X-ray diffraction, Brunauer–Emmett–Teller (BET), transmission electron microscopy, and UV–vis spectra (UV–vis). The results showed that both Ag and TiO₂ nanoparticles were well-dispersed over the MWCNTs and formed a uniform nanocomposite. Ag doping can eliminate the recombination of electron–hole pairs in the catalyst, and the presence of MWCNTs in the TiO₂ composite can change surface properties to achieve sensitivity to visible light. The optimum mass ratio of MWCNT:TiO₂:Ag was 0.02:1.0:0.05, which resulted in the photocatalyst's experimental performance in oxidizing about 100% of the thiophene in a 600 mg/L solution within 30 min and with 1.4 g L⁻¹ amount of catalyst used.     

Facile synthesis of mesoporous Ag-loaded TiO2 thin film and its photocatalytic properties

Ag nanoparticles highly dispersed into TiO₂ thin films are synthesized via a remarkably simple one-pot route in the presence of a P123 triblock copolymer as template directing and reducing agents, where the reduction of Ag⁺ to Ag⁰ by in situ heat-induced reduction through the oxidation of template at 400 °C and the controlled polymerization of TiO₂ take place simultaneously. The obtained mesoporous Ag/TiO₂ films deposited on soda-lime glass were optically transparent and crack-free. SEM and Kr adsorption clearly prove that Ag/TiO₂ films at different Ag contents are mesoporous with large surface area and regularly ordered mesopores and the thickness of the obtained films is ∼280 ± 20 nm. The pristine TiO₂ film exhibits a specific surface area of 63 cm²/cm² and specific pore volume of 0.013 mm³/cm² that it is decreased to 42 cm²/cm² and 0.010 mm³/cm² respectively as a result of Ag-loaded mesoporous TiO₂. The newly prepared photocatalysts Ag/TiO₂ films were evaluated for their photocatalytic degradation of 2-chlorophenol as a model reaction. It was found that the meso-ordered Ag/TiO₂ films are more photoactive 8 times than nonporous commercial photocatalysts Pilkington Glass Activ™. The recycling tests indicated that Ag/TiO₂ films was quite stable during that liquid-solid heterogeneous photocatalysis since no significant decrease in activity was observed even after being used repetitively for 10 times, showing a good potential in practical application. In general, the cubic mesoporous Ag/TiO₂ nanocomposites are stable and can be recycled without loss of their photochemical activity.     

Onset coarsening-coalescence kinetics of ZrO2 and less refractory TiO2 nanoparticles: Effect of homologous temperature and phase transformation

Specific surface area change of ZrO₂ (predominant tetragonal - (t) symmetry, 30-50 nm) and less refractory TiO₂ anatase nanoparticles (20-50 nm) upon isothermal firing at 700-1000 °C in air was determined by N₂ adsorption-desorption hysteresis isotherm. The nanoparticles underwent onset coarsening-coalescence within minutes without appreciable phase transformation for TiO₂, but with extensive transformation into monoclinic (m-) symmetry for ZrO₂. The apparent activation energy of such a process being not much higher for ZrO₂ (77 ± 23 kJ/mol) than TiO₂ (56 ± 3 kJ/mol) nanoparticles can be attributed to transformation plasticity. The minimum temperature for coarsening/coalescence of the present ZrO₂ and TiO₂ nanoparticles was estimated as 710 and 641 °C, respectively.     

Lithium-ion battery anode properties of TiO2 nanotubes prepared by the hydrothermal synthesis of mixed (anatase and rutile) particles

From mixed (anatase and rutile) bulk particles, anatase TiO₂ nanotubes are synthesized in this study by an alkaline hydrothermal reaction and a consequent annealing at 300-400 °C. The physical and electrochemical properties of the TiO₂ nanotube are investigated for use as an anode active material for lithium-ion batteries. Upon the first discharge-charge sweep and simultaneous impedance measurements at local potentials, this study shows that interfacial resistance decreases significantly when passing lithium ions through a solid electrolyte interface layer at the lithium insertion/deinsertion plateaus of 1.75/2.0 V, corresponding to the redox potentials of anatase TiO₂ nanotubes. For an anatase TiO₂ nanotube containing minor TiO₂(B) phase obtained after annealing at 300 °C, the high-rate capability can be strongly enhanced by an isotropic dispersion of TiO₂ nanotubes to yield a discharge capacity higher than 150 mAh g⁻¹, even upon 100 cycles of 10 C-rate discharge-charge operations. This is suitable for use as a high-power anode material for lithium-ion batteries.     

Nafion-TiO2 composite DMFC membranes: physico-chemical properties of the filler versus electrochemical performance

TiO₂ nanometric powders were prepared via a sol-gel procedure and calcined at various temperatures to obtain different surface and bulk properties. The calcined powders were used as fillers in composite Nafion membranes for application in high temperature direct methanol fuel cells (DMFCs). The powder physico-chemical properties were investigated by X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and pH measurements. The observed characteristics were correlated to the DMFC electrochemical behaviour. Analysis of the high temperature conductivity and DMFC performance reveals a significant influence of the surface characteristics of the ceramic oxide, such as oxygen functional groups and surface area, on the membrane electrochemical behaviour. A maximum DMFC power density of 350 mW cm⁻² was achieved under oxygen feed at 145 °C in a pressurized DMFC (2.5 bar, anode and cathode) equipped with TiO₂ nano-particles based composite membranes.     

CNT@TiO2 nanohybrids for high-performance anode of lithium-ion batteries

This work describes a potential anode material for lithium-ion batteries (LIBs), namely, anatase TiO₂ nanoparticle-decorated carbon nanotubes (CNTs@TiO₂). The electrochemical properties of CNTs@TiO₂ were thoroughly investigated using various electrochemical techniques, including cyclic voltammetry, electrochemical impedance spectroscopy, galvanostatic cycling, and rate experiments. It was revealed that compared with pure TiO₂ nanoparticles and CNTs alone, the CNT@TiO₂ nanohybrids offered superior rate capability and achieved better cycling performance when used as anodes of LIBs. The CNT@TiO₂ nanohybrids exhibited a cycling stability with high reversible capacity of about 190 mAh g^-1 after 120 cycles at a current density of 100 mA g^-1 and an excellent rate capability (up to 100 mAh g^-1 at a current density of 1,000 mA g^-1).     

Effect of annealing on the phase transition and morphology of Ag NPs on/in TiO2 rods synthesized by a polyol method

In this study, we report the effect of annealing (250–700 ^oC) on the phase transition and morphology of silver (Ag) nanoparticles (NPs) on/in titanium dioxide (TiO₂) rods prepared using a polyol method. The annealed samples showed not only morphological change, i.e., a solid-to-liquid (melting) transition of Ag NPs due to its partial dissolution into the TiO₂ rods, but also early stage anatase crystallization and anatase–rutile transformation of TiO₂ rods under low annealing temperatures. Such findings, together with XRD and FE-SEM analyses, confirm that, upon higher annealing treatment, diffusion and coalescence leads to changes in the size and shape of the metal particles not only in the outermost regions, but also a random distribution and progressive growth of Ag clusters in the inner interface region. Here, it was shown that annealing can induce changes in morphology, as well as the chemical state and structure of Ag–TiO₂. The present polyol-synthesized Ag–TiO₂ composite also showed improved thermal stability.     

Hydrothermal preparation of Ag-TiO2 nanostructures with exposed {001}/{101} facets for enhancing visible light photocatalytic activity

Nano-composite materials of Ag nanoparticles dispersed TiO₂ nanocubes with exposed {001}/{101} crystal faces were fabricated mainly via a flexible one-step method of hydrothermal treatment with different content of Ag from 1 up to 3 mol%. Prepared photocatalysts were characterized by X-ray diffraction, scanning electron microscope, transmission electron microscopy, UV–vis absorption spectroscopy, X-ray photoelectron spectroscopy and Raman spectroscopy. These analysis was carried out for understanding the contribution of different content of silver for enhancing the photocatalytic activity of TiO₂ nanocubes. Prepared silver nanoparticles had small particle size and grafted to the {101} crystal face of TiO₂ with the role of template control agent and linking agent. The photocatalytic performance of Ag-TiO₂ nanocubes were researched via Rhodamine B dye removal under visible light irradiation ( ≧420 nm). Ag-TiO₂ composite materials with the content of 2 mol% Ag showed the best photocatalytic activity for degradation of Rhodamine B, which was five times more than bare TiO₂ and associated with the localized surface plasmon resonance (LSPR) propelled effect. The mechanism by which silver enhanced the photocatalytic activity of TiO₂ was also demonstrated.     

The preparation and characterization of Li4Ti5O12/carbon nano-tubes for lithium ion battery

Li₄Ti₅O₁₂/carbon nano-tubes (CNTs) composite was prepared by sol-gel method while Ti(OC₄H₉)₄, LiCH₃COO·2H₂O and the n-heptane containing CNTs were used as raw materials. The characters of Li₄Ti₅O₁₂/CNTs composite were determined by XRD, SEM, and TG methods. Its electrochemical properties were measured by charge-discharge cycling and impedance tests. It was found that the prepared Li₄Ti₅O₁₂/CNTs presented an excellent rate capability and capacity retention. At the charge-discharge rate of 5C and 10C, its discharge capacities were 145 and 135 mAh g⁻¹, respectively. After 500 cycles at 5C, the discharge capacity retained as 142 mAh g⁻¹. It even could be cycled at the rate of 20C. The excellent electrochemical performance of Li₄Ti₅O₁₂/CNTs electrode could be attributed to the improvement of electronic conductivity by adding conducting CNTs and the nano-size of Li₄Ti₅O₁₂ particles in the Li₄Ti₅O₁₂/CNTs composite.     

Microwave-polyol synthesis of nanocrystalline ruthenium oxide nanoparticles on carbon nanotubes for electrochemical capacitors

The ruthenium oxide nanoparticles dispersed on multi-wall carbon nanotubes (CNTs) were successfully synthesized via microwave-polyol process combined with forced hydrolysis without additional thermal oxidation or electrochemical oxidation treatment. The HRTEM, Raman spectra and TGA curve indicate that CNTs were uniformly coated with crystalline and partially hydrous RuO₂·0.64H₂O nanoparticles of 2 nm diameter and the loading amount of ruthenium oxide in the composite could be controlled up to 70 wt.%. The specific capacitance was 450 Fg⁻¹ of ruthenium oxide/CNT composite electrode with 70 wt.% ruthenium oxide at the potential scan rate of 10 mV s⁻¹ and it decreased to 362 Fg⁻¹ by 18% at 500 mV s⁻¹. The specific capacitance of ruthenium oxide in the composite was 620 Fg⁻¹ of ruthenium oxide at 10 mV s⁻¹. The ruthenium oxide nanoparticles in ruthenium oxide/CNT nanocomposite electrode had a high ratio of outer charge to total charge of 0.81, which confirmed its high-rate capability of the composite through the preparation of the nano-sized ruthenium oxide particles on the external surface of CNTs.     

Enhanced photoresponse and photocatalytic activities of graphene quantum dots sensitized Ag/TiO2 thin film

TiO₂ thin films were fabricated through hydrothermal method. Silver nanoparticles were loaded on TiO₂ thin films via photoreduction technique. Subsequently, the graphene quantum dots (GQDs) were spin‐coated on the Ag/TiO₂ nanocomposites thin films. The crystal structure, surface morphology and UV‐vis absorbance were tested by XRD, SEM and ultraviolet‐visible spectrophotometer. These results indicated that Ag nanoparticles and GQDs are anchored on the TiO₂ nanorods. Absorbance of Ag/TiO₂ and GQDs/Ag/TiO₂ nanocomposite thin films have been extended into the visible region. Visible‐light response of the samples were investigated by electrochemical workstation. The photoresponse of the sample can be enhanced by sensitization of the Ag nanoparticles and GQDs. The enhanced visible‐light response may be due to the surface plasmon resonance of silver nanoparticles and visible absorbance of GQDs. The highest photocatalytic activity has been observed in the 9‐GQDs/Ag/TiO₂ composite thin film. The efficient charge separation and transportation can be achieved by introducing the Ag nanoparticles and GQDs in the TiO₂ thin film.     

Electrochemical impedance spectroscopy and corrosion behaviour of Al2O3-Ni nano composite coatings

In this paper, the results on the electrochemical impedance spectroscopy and corrosion properties of electrodeposited nanostructured Al₂O₃-Ni composite coatings are presented. The nanocomposite coatings were obtained by codeposition of alumina nanoparticles (13 nm) with nickel during plating process. The coating thickness was 50 μm on steel support and an average of nano Al₂O₃ particles inside of coatings at 15 vol.% was present. The structure of the coatings was investigated by scanning electron microscopy (SEM). It has been found that the codeposition of Al₂O₃ particles with nickel disturbs the nickel coating's regular surface structure. The electrochemical behavior of the coatings in the corrosive solutions was investigated by polarization potentiodynamic and electrochemical impedance spectroscopy methods. As electrochemical test solutions 0.5 M sodium chloride and 0.5 M potassium sulphate were used in a three electrode open cell. The corrosion potential is shifted to more negative values for nanostructured coatings in 0.5 M sodium chloride. The polarization resistance in 0.5 M sodium chloride decreases in 24 h, but after that increases slowly. In 0.5 M potassium sulphate solution the polarization resistance decreases after 2 h and after 30 h of immersion the polarization resistance is higher than that of the beginning value. The corrosion rate calculated by polarization potentiodynamic curves obtained after 30 min from immersion in solution is smaller for nanostructured coatings in 0.5 M potassium sulphate (4.74 μm/year) and a little bit bigger in 0.5 M sodium chloride (5.03 μm/year).     

Photoelectro-Fenton combined with photocatalytic process for degradation of an azo dye using supported TiO2 nanoparticles and carbon nanotube cathode: Neural network modeling

In this work, treatment of an azo dye solution containing C.I. Basic Red 46 (BR46) by photoelectro-Fenton (PEF) combined with photocatalytic process was studied. Carbon nanotube-polytetrafluoroethylene (CNT-PTFE) electrode was used as cathode. The investigated photocatalyst was TiO₂ nanoparticles (Degussa P25) having 80% anatase and 20% rutile, specific surface area (BET) 50 m²/g, and particle size 21 nm immobilized on glass plates. A comparison of electro-Fenton (EF), UV/TiO₂, PEF and PEF/TiO₂ processes for decolorization of BR46 solution was performed. Results showed that color removal follows the decreasing order: PEF/TiO₂ > PEF > EF > UV/TiO₂. The influence of the basic operational parameters such as initial pH of the solution, initial dye concentration, the size of anode, applied current, kind of ultraviolet (UV) light and initial Fe³⁺ concentration on the degradation efficiency of BR46 was studied. The mineralization of the dye was investigated by total organic carbon (TOC) measurements that showed 98.8% mineralization of 20 mg/l dye at 6 h using PEF/TiO₂ process. An artificial neural network (ANN) model was developed to predict the decolorization of BR46 solution. The findings indicated that artificial neural network provided reasonable predictive performance (R² = 0.986).     

Electrochemical performance of arc-produced carbon nanotubes as anode material for lithium-ion batteries

The effects of etching process on the morphology, structure and electrochemical performance of arc-produced multiwalled carbon nanotubes (CNTs) as anode material for lithium-ion batteries were systematically investigated by TEM and a variety of electrochemical testing techniques. It was found that the etched CNTs exhibited four times higher reversible capacity than that of raw CNTs, and possessed excellent cyclability with almost 100% capacity retention after 30 cycles. The kinetic properties of three kinds of CNTs electrodes involving the pristine (CNTs-1), etched (CNTs-2) as well as etch-carbonized samples (CNTs-3) were characterized via ac impedance measurement. It was indicated that, after 30 cycles the exchange current density i₀ of etched CNTs ((7.6-7.8) × 10⁻³ A cm⁻²) was higher than that of the raw CNTs (5.9 × 10⁻³ A cm⁻²), suggesting the electrochemical activity of CNTs was enhanced by the etching treatment. The storage characteristics of the CNTs electrodes at room temperature and 50 °C were particularly compared. It was found that the film resistance on CNTs electrode generally tended to become large with the elongation of storage time, especially storage at high temperature. In comparison with CNTs-1 and CNTs-3, CNTs-2 exhibited more distinctly increase of film resistance, which is related with the surface properties.     

Synthesis and electrochemical studies of a layered spheric TiO2 through low temperature solvothermal method

This paper demonstrates a low temperature solvothermal method for the synthesis of a layered spheric TiO₂. The crystal structure and morphology of the material were characterized by using X-ray diffraction (XRD) and scanning electron miscopy (SEM). Electrochemical performances of the TiO₂ when used as anode material in lithium ion batteries were investigated by galvanostatic charge/discharge and cyclic voltammetry experiments. A discharge capacity of 179 mAh g⁻¹ was obtained in the potential range between 3.0 and 1.5 V. No significant capacity decay was observed in the successive 30 cycles showing satisfactory cycling performance of the electrode.     

Controllable preparation of Ti/TiO2-NTs/PbO2–CNTs–MnO2 layered composite materials with excellent electrocatalytic activity for the OER in acidic media

High oxygen evolution overpotential and low corrosion resistance are the main challenges for oxygen evolution materials in acidic media. In this study, a novel composite material, Ti/TiO₂-NTs/PbO₂–CNTs–MnO₂, with high oxygen evolution electrocatalytic activity was successfully prepared. First, TiO₂ nanotubes (TiO₂-NTs) were synthesized in situ on a Ti sheet via anodization and used as an intermediate layer. Subsequently, the adhesion and conductivity of the TiO₂-NTs layer were increased through additional anodization, annealing, and electrochemical reduction. Finally, PbO₂ was electrodeposited with a constant current in a lead acetate medium and doped with carbon nanotubes (CNTs) and MnO₂. The surface morphology, phase composition, and electrochemical performance of the composite materials were investigated. Notably, in an acidic electrolyte (150 g/L H₂SO₄), Ti/TiO₂-NTs/PbO₂–CNTs–MnO₂ exhibited good stability (30 h) and a low oxygen evolution overpotential of 410 mV at 50 mA/cm², which is almost equivalent to that of precious metals (RuO₂ and IrO₂) and 499 mV lower than that of the industrial Pb–0.76 wt% Ag alloy. The outstanding performance is mainly attributed to the high aspect ratio of the TiO₂-NT structure, synergistic effects of the active particles, and inherently good electrochemical properties of the active particles. Therefore, this study provides a new synthetic route for oxygen evolution materials in acidic media.     

High performance electrode for electrochemical oxygen generator cell based on solid electrolyte ion transport membrane

A double-layer composite electrode based on Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ + Sm_0.2Ce_0.8O_1.9 (BSCF + SDC) and BSCF + SDC + Ag was investigated to be a promising cathode and also anode for the electrochemical oxygen generator based on samaria doped ceria electrolyte. The Ag particles in the second layer were not only the current collector but also the improver for the oxygen adsorption at the electrode. a.c. impedance results indicated that the electrode polarization resistance, as low as 0.0058 Ω cm² was reached at 800 °C under air. In oxygen generator cell performance test, the electrode resistance dropped to half of the value at zero current density under an applied current density of 2.34 A cm⁻² at 700 °C, and on the same conditions the oxygen generator cell was continual working for more than 900 min with a Faradic efficiency of ∼100%.     

Strategy for the syntheses of isolated fine silver nanoparticles and polypyrrole/silver nanocomposites on gold substrates

In this work, isolated fine silver nanoparticles and polypyrrole/silver nanocomposites with diameters of about 10 nm on gold substrates were first prepared by electrochemical methods. First, an Ag substrate was cycled in a deoxygenated aqueous solution containing 0.1 M HCl from −0.30 to +0.30 V versus Ag/AgCl at 5 mV/s with 30 scans. Subsequently the Ag working electrode was immediately replaced by an Au electrode and a cathodic overpotential of 0.2 V was applied under controlled sonication to synthesize Ag nanoparticles on the Au electrode. Then pyrrole monomers were encouragingly found to be polymerized on the deposited Ag nanoparticles. This polymerization is distinguishable from the known chemical or electrochemical one, due to the electrochemical activity of unreduced species of Ag_n⁺ clusters inside the nanoparticles. Also, this polymerization may be ascribed to the oxidizing agent of AuCl₄⁻, which is present on the Au electrode.