A study of the Fe(III)/Fe(II)-triethanolamine complex redox couple for redox flow battery application

The electrochemical behavior of the Fe(III)/Fe(II)-triethanolamine(TEA) complex redox couple in alkaline medium and influence of the concentration of TEA were investigated. A change of the concentration of TEA mainly produces the following two results. (1) With an increase of the concentration of TEA, the solubility of the Fe(III)-TEA can be increased to 0.6 M, and the solubility of the Fe(II)-TEA is up to 0.4 M. (2) In high concentration of TEA with the ratio of TEA to NaOH ranging from 1 to 6, side reaction peaks on the cathodic main reaction of the Fe(III)-TEA complex at low scan rate can be minimized. The electrode process of Fe(III)-TEA/Fe(II)-TEA is electrochemically reversible with higher reaction rate constant than the uncomplexed species. Constant current charge-discharge shows that applying anodic active materials of relatively high concentrations facilitates the improvement of cell performance. The open-circuit voltage of the Fe-TEA/Br₂ cell with the Fe(III)-TEA of 0.4 M, after full charging, is nearly 2.0 V and is about 32% higher than that of the all-vanadium batteries, together with the energy efficiency of approximately 70%. The preliminary exploration shows that the Fe(III)-TEA/Fe(II)-TEA couple is electrochemically promising as negative redox couple for redox flow battery (RFB) application.     

Investigation of Ir-modified carbon felt as the positive electrode of an all-vanadium redox flow battery

Porous graphite felts have been used as electrode materials for all-vanadium redox flow batteries due to their wide operating potential range, stability as both an anode and a cathode, and availability in high surface area. In this paper, the carbon felt was modified by pyrolysis of Ir reduced from H₂IrCl₆. ac impedance and steady-state polarization measurements showed that the Ir-modified materials have improved activity and lowered overpotential of the desired V(IV)/V(V) redox process. Ir-modification of carbon felt enhanced the electro-conductivity of electrode materials. The Ir-material, when coated on the graphite felt electrode surface, lowered the cell internal resistance. A test cell was assembled with the Ir-modified carbon felt as the activation layer of the positive electrode, the unmodified raw felt as the activation layer of the negative electrode. At an operating current density of 20 mA cm⁻², a voltage efficiency of 87.5% was achieved. The resistance of the cell using Ir-modified felt decreased 25% compared to the cell using non-modified felt.     

Nickel foam and carbon felt applications for sodium polysulfide/bromine redox flow battery electrodes

The first use of nickel foam (NF) as electrocatalytic negative electrode in a polysulfide/bromine battery (PSB) is described. The performance of a PSB employing NF and polyacrylonitrile (PAN)-based carbon felt (CF) as negative and positive electrode materials, respectively, was evaluated by constant current charge-discharge tests in a single cell. Charge/discharge curves of the cell, positive and negative electrodes show that the rapid fall in cell voltage is due to the drop of positive potential caused by depletion of Br₂ dissolved in the catholyte at the end of discharge. Cell voltage efficiency was limited by the relatively high internal ohmic resistance drop (iR drop). Polarization curves indicated that both NF and CF have excellent catalytic activity for the positive and negative redox reactions of PSB. The average energy efficiency of the single cell designed in this work could be as high as 77.2% at 40 mA cm⁻² during 48 charge-discharge cycles.     

A study of the Ce(III)/Ce(IV) redox couple for redox flow battery application

In this study, the electrochemical behavior of the Ce(III)/Ce(IV) redox couple in sulfuric acid medium with various concentrations and the influence of the operating temperature were investigated. A change of the concentration of sulfuric acid mainly produced the following two results. (1) With an increase of the concentration of sulfuric acid the redox peak currents decreased. (2) The peak potential separation for the redox reactions increased with rising concentration of sulfuric acid from 0.1 to 2 M and then decreased with further increase of the concentration. Elevated temperature was electrochemically favorable for Ce(III)/Ce(IV) couple, which caused an increase of the peak currents for the redox reactions and a decrease of the peak potentials separation. Constant-current electrolysis shows that the current efficiency was 73% for the oxidation process of Ce(III) and 78% for the reduction process at 298 K, and could be improved by elevating the temperature. The open-circuit voltage of the Ce-V cell, after full charging, remained constant at 1.870±0.005 V for more than 48 h, and is about 29% higher than that of the all-vanadium batteries. The coulombic efficiency was approximately 87%, showing that self-discharge of the Ce-V battery was small. The preliminary exploration shows that the Ce(III)/Ce(IV) couple is electrochemically promising for redox flow battery (RFB) application.     

全钒氧化还原液流电池用石墨毡电极的稳定性

为了探究全钒氧化还原液流电池用石墨毡电极的稳定性,采用循环伏安、质量分析法、SEM和充放电实验研究了石墨毡的电化学性能、质量及形貌的变化。研究结果表明：实验选用的石墨毡电极在实验时间内因氧化而发生失重,同时吸附电解液,使电极质量随时间变化呈先减少后增加的趋势。但是,石墨毡的电化学性能仍然保持稳定,单片电池的能量效率及库仑效率维持在80%与96%左右。     

Highly hydroxylated carbon fibres as electrode materials of all-vanadium redox flow battery

A highly effective hydroxylated-functionalization of carbon fibres for use as electrodes of all-vanadium redox flow battery (VRFB) was developed. Carbon paper made of carbon fibres was hydroxylated ultrasonically with mixed acids (H₂SO₄/HNO₃, V_H2SO4/V_HNO3 = 3/1) in a Teflon-lined stainless steel autoclave for different time at 80 °C. The structure, composition, and electrochemical properties of the treated samples for positive and negative electrodes of VRFB were characterized with Fourier transformation infrared spectroscopy, thermogravimetric analysis, X-ray photoelectron spectrometry, scanning electron microscopy, X-ray diffraction, cyclic voltammetry, electrochemical impedance spectroscopy, and cell charge and discharge tests. The content of hydroxyl group changes from 3.8% for the untreated sample to 14.3% for the carbon paper treated in mixed acids for 10 h. The highly hydroxylated sample shows its high activity toward the redox reactions of V(II)/V(III) and V(IV)/V(V). The VRFB using the carbon paper treated for 8 h as the electrodes exhibits excellent performance under a current density of 10 mA cm⁻². The average voltage efficiency reaches 91.3%, and the average energy efficiency reaches 75.1%. The mechanisms for the high hydroxylation of the carbon fibres with the mixed acids and the high activity of the treated sample toward the vanadium redoxs are discussed.     

The characterization and bioelectrocatalytic properties of hemoglobin by direct electrochemistry of DDAB film modified electrodes

Direct electrochemistry of hemoglobin can be performed in acidic and basic aqueous solutions in the pH range 1-13, using stable, electrochemically active films deposited on a didodecyldimethylammonium bromide (DDAB) modified glassy carbon electrode. Films can also be produced on gold, platinum, and transparent semiconductor tin oxide electrodes. Hemoglobin/DDAB films exhibit one, two, and three redox couples when transferred to strong acidic, weak acidic and weak basic, and strong basic aqueous solutions, respectively. These redox couples, and their formal potentials, were found to be pH dependent. An electrochemical quartz crystal microbalance and cyclic voltammetry were used to study the in situ deposition of DDAB on gold disc electrodes and hemoglobin deposition on DDAB film modified electrodes. A hemoglobin/DDAB/GC modified electrode is electrocatalytically reduction active for oxygen and H₂O₂, and electrocatalytically oxidation active for S₂O₄²⁻ through the Fe(III)/Fe(II) redox couple. In the electrocatalytic reduction of S₄O₆²⁻, S₂O₄²⁻, and SO₃²⁻, and the dithio compounds of 2,2′-dithiosalicylic acid and 1,2-dithiolane-3-pentanoic acid, the electrocatalytic current develops from the cathodic peak of the redox couple at a potential of about −0.9 V (from the Fe(II)/Fe(I) redox couple) in neutral and weakly basic aqueous solutions. Hemoglobin/DDAB/GC modified electrodes are electrocatalytically reduction active for trichloroacetic acid in strong acidic buffered aqueous solutions through the Fe(III)/Fe(II) redox couple. However, the electrocatalytic current developed from the cathodic peak of the redox couple at a potential of about −0.9 V (from the Fe(II)/Fe(I) redox couple) in weak acidic and basic aqueous solutions. The electrocatalytic properties were investigated using the rotating ring-disk electrode method.     

Electrochemical synthesis of Cr(II) at carbon electrodes in acidic aqueous solutions

The electrochemical synthesis of Cr(II) has been investigated on a vitreous carbon rotating disc electrode and a graphite felt electrode using cyclic voltammetry, impedance spectroscopy and chronoamperometry. The results show that in 0.1 M Cr(III) + 0.5 M sulphuric acid and in 0.1 M Cr(III) + 1 M hydrochloric acid over an electrode potential range of –0.8 to 0.8 V vs SCE, the electrochemical reaction at carbon electrodes is essentially a surface process of proton adsorption and desorption, without significant hydrogen evolution and chromium(II) formation. At electrode potentials more negative than –0.8 V vs SCE, both hydrogen evolution and chromium(II) formation occurred simultaneously. At electrode potentials –0.8 to –1.2 V vs SCE, the electrochemical reduction of Cr(III) on carbon electrodes is controlled mainly by charge transfer rather than mass transport. Measurements on vitreous carbon and graphite felt electrodes in 1 M HCl, with and without 0.1 M CrCl₃, allowed the exchange current density and Tafel slope for hydrogen evolution, and for the reduction of Cr(III) to Cr(II), to be determined. The chromium(III) reduction on vitreous carbon and graphite electrodes can be predicted by the extended high field approximation of the Butler–Volmer equation, with a term reflecting the conversion rate of Cr(III) to Cr(II).     

Poly(o-aminophenol) film prepared in the presence of sodium dodecyl sulfate: Application for nickel ion dispersion and the electrocatalytic oxidation of methanol and ethylene glycol

Poly(o-aminophenol) (POAP) was formed by successive cyclic voltammetry in monomer solution in the presence of sodium dodecyl sulfate (SDS) on the surface of a carbon paste electrode. The electrochemical behavior of the SDS-POAP carbon paste electrode has been investigated by cyclic voltammetry in 0.5 M HClO₄ and 5 mM K₄[Fe(CN)₆]/0.1 M KCl solutions as the supporting electrolyte and model system, respectively. Ni(II) ions were incorporated into the electrode by immersion of the polymeric modified electrode having amine groups in 0.1 M Ni(II) ion solution. Cyclic voltammetric and chronoamperometric experiments were used for the electrochemical study of this modified electrode. A good redox behavior of the Ni(III)/Ni(II) couple at the surface of electrode can be observed. The electrocatalytic oxidations of methanol and ethylene glycol (EG) at the surface of the Ni/SDS-POAP electrode were studied in a 0.1 M NaOH solution. Compared to bare carbon paste and POAP-modified carbon paste electrodes, the SDS-POAP electrode significantly enhanced the catalytic efficiency of Ni ions for methanol oxidation. Finally, using a chronoamperometric method, the catalytic rate constants (k) for methanol and ethylene glycol were found to be 2.04 × 10⁵ and 1.05 × 10⁷ cm³ mol⁻¹ s⁻¹, respectively.     

Chromium redox couples for application to redox flow batteries

Both anodic and cathodic chromium-EDTA (ethylenediaminetetra-acetate) complex redox processes have been studied using cyclic voltammetry. Their potential use in a redox battery has been evaluated by comparing the charge and discharge performance of a simple redox battery employing several redox couples including the conventional Fe-Cr redox couples. The cyclic voltammetry experiments suggested that oxidation of Cr(III)-EDTA formed Cr(V)-EDTA rather than a hexavalent chromium species. It was found that the kinetics of the Cr(III)-EDTA/Cr(II)-EDTA redox reaction are fast at a graphite rod electrode, whereas the Cr(V)-EDTA/Cr(III)-EDTA redox reaction is relatively slow. In spite of the slow kinetics, the battery employing solely these chromium-EDTA based redox couples provided higher energy output and longer life than the conventional Fe-Cr redox system.     

Electrocatalytic oxidation of methanol on carbon paste electrode modified by nickel ions dispersed into poly (1,5-diaminonaphthalene) film

Poly (1,5-diaminonaphthalene) film was prepared by using the repeated potential cycling technique in an acidic solution at the surface of carbon paste electrode. Then transition metal ions of Ni(II) were incorporated to the polymer by immersion of the modified electrode in a 1.0 M nickel chloride solution. The electrochemical characterization of this modified electrode exhibits stable redox behavior of the Ni(III)/Ni(II) couple. Also, cyclic voltammetric experiments showed that methanol electrooxidized at the surface of this Ni(II) dispersed polymeric modified carbon paste electrode [Ni/P-1,5-DAN/MCPE]. The mechanism of methanol oxidation changes from diffusion control at low concentration to a catalytic reaction at higher methanol concentration. The effects of both scan rate and methanol concentration on the anodic peak height of the methanol oxidation were discussed.     

Improved performance of iron-chromium flow batteries using SnO2-coated graphite felt electrodes

Polyacrylonitrile-based graphite felt has the properties of high temperature resistance, corrosion resistance, low thermal conductivity, large surface area and excellent electrical conductivity. It has become the preferred material for flow battery electrodes, but its chemical activity is poor. In order to improve the electrochemical activity of graphite felt electrodes, the electrodes were prepared by SnO₂-coated graphite felt. Scanning electron microscopy and X-ray photoelectron spectroscopy were used to analyze the microscopic morphology of SnO₂-coated graphite felt electrodes. Electrochemical impedance spectroscopy, cyclic voltammetry and charge-discharge tests were performed using an electrochemical workstation to investigate the electrocatalytic activity of SnO₂-coated graphite felt electrodes and their cell performance. The results show that the SnO₂ coating on the graphite felt surface forms a convex and concave microstructure, which further increases the specific surface area of the electrode, and at the same time successfully introduces oxygen-containing functional groups to the electrode surface, increasing the electrochemically active spots on the surface. In addition, the presence of oxygen defects in the SnO₂ crystal structure provides more electrochemically active sites and improves the electrochemical performance of the graphite felt electrode. At a current density of 142 mA cm^?2, the charge-discharge capacity of the battery assembled with the SnO₂-coated graphite felt electrode was significantly improved; when the current density was 250 mAcm^?2, the Coulombic efficiency of the electrode (TGF-2) coated with a concentration of 0.1 M could reach 84%.     

The Redox Chemistry of Manganese(III) and -(IV) Complexes

The oxidation-reduction thermodynamics for the manganese(III), -(IV), and -(II) ions, and their various complexes, are reviewed for both aqueous and aprotic media. In aqueous solutions the reduction potential for the manganese(III)/(II) couple has values that range from +1.51 V vs. NHE (hydrate at pH 0) to −0.95 V (glucarate complex at pH 13.5). The Mn(IV)/(III) couple has values that range from +1.0 V (solid Mn^IVO₃ at pH 0) to −0.04 V (tris gluconate complex at pH 13.5). With anhydrous media the propensity for the Mn(III) ion to disproportionate to solid Mn^IVO₂ and Mn(II) ion is avoided. For aprotic systems the range of redox potentials for various manganese complexes is from +2.01 V and +1.30 for the Mn(IV)/(III) and Mn(III)/(II) couples (bis terpyridyl tri-N-oxide complex in MeCN), respectively, to −0.96 V for the Mn(IV)/(III) couple (tris 3,5,-di-tert-butylcatecholate complex in Me₂SO). The redox reactions between manganese complexes and dioxygen species (O₂, O₂, and H₂O₂) also are reviewed.     

Effect of Bi(III) concentration on the stripping voltammetric response of in situ bismuth-coated carbon paste and gold electrodes

The effect of Bi(III) concentration (over the wide concentration range of 10⁻⁷ to 10⁻⁴ M) on the determination of Pb and Cd metal ions (in the 10⁻⁸ to 10⁻⁵ M range), by means of anodic stripping voltammetry (ASV) at in situ bismuth-coated carbon paste (CPE) and gold electrodes, has been studied. It is shown that in square wave anodic stripping voltammetry (SWASV) experiments the sensitivity of the technique generally depends on the Bi(III)-to-metal ion concentration ratio. It was found that, unlike the usually recommended at least 10-fold Hg(II) excess in anodic stripping experiments at in situ prepared mercury film electrodes, Bi(III)-to-metal ion ratios less than 10 are either optimal or equally effective at CPE and Au electrode substrates. Detection limits down to 0.1 μg L⁻¹ for Pb(II) and 0.15 μg L⁻¹ for Cd(II) were estimated at CPEs under conditions of small or moderate Bi(III) excess. Depending on Bi(III) concentration and deposition time, multiple stripping peaks attributed to Bi were recorded (especially in the case of Au substrates), indicating various forms of Bi deposits.     

全钒液流电池石墨毡电极的Ga2O3修饰

为提高全钒液流电池石墨毡电极的电化学性能, 采用热分解法将纳米Ga₂O₃沉积在全钒液流电池石墨毡电极表面。通过循环伏安测试、动电位极化曲线测试、扫描电镜测试(SEM)、X射线光电子能谱分析(XPS)和充放电实验考察了Ga₂O₃对石墨毡电化学性能和表面形貌的影响。研究结果表明:Ga₂O₃对电极反应具有显著的催化作用, 当用Ga₂O₃电极修饰石墨毡时, 电池正负极反应活性较未处理前分别提高13%和18%, 同时也导致全钒液流电池的容量更大, 电流效率和能量效率更高。     

The mediation reaction between the external couple Ferri/Ferrocyanide and Os(II) bipyridile poly-vinylpyridile films coated onto glassy carbon electrodes

The oxidation-reduction of the Ferri/Ferrocyanide couple in solution onto modified glassy carbon Rotating Disk Electrodes (RDE) covered by Os(II) bipyridile poly-vinylpyridile (OsBPP) polymer was studied at room temperature. Steady state polarization curves were carried out as a function of the rotation speed, the polymer thickness and the concentration of redox centers within the polymer. This system has the characteristic that the formal redox potentials of both the external redox couple (E⁰′(Fe(CN)₆^3−/4−) = + 0.225 V vs. SCE) and the mediator polymer (E⁰′(OsBPP) = 0.260 V vs. SCE) lie very close. It is demonstrated that diffusion of the Ferri/Ferrocyanide inside the polymer can be ruled out. Since the processes of charge transfer at the metal/polymer and the mediating reaction are fast, the experimental results can be interpreted in terms of a kinetics in which the charge transport in the polymer or the diffusion in the solution may be the rate determining step, according to the experimental conditions. A simple model is considered that allows interpreting the experimental results quantitatively. Application of this model allows the determination of the diffusion coefficient of the electrons within the film, D_e ≈ 10⁻¹⁰ cm² s⁻¹.     

Electrochemical studies on the redox mechanism of uranium chloride in molten LiCl-KCl eutectic

The reduction and oxidation processes on platinum and glassy carbon electrodes in molten LiCl-KCl eutectic containing UCl₃ were investigated by cyclic voltammetry (CV), chronopotentiometry and electrochemical impedance spectroscopy (EIS) in the temperature range 660-780 K. Two redox peaks have been observed in the cyclic voltammograms corresponding to the two redox reactions U(IV)/U(III) and U(III)/U which are found to be reversible and quasi-reversible, respectively. The reduction potentials of U(IV)/U(III) and U(III)/U are −0.325 and −1.490 V versus reference electrode (0.1 mol% AgCl in the LiCl-KCl), respectively at 700 K. Chronopotentiometric measurements confirm the three-electron transfer during the reduction of U(III) to U metal. Electrochemical impedance spectroscopy data at various potentials were interpreted either as diffusion, adsorption or reduction process by nonlinear fit of the impedance data to the simulated equivalent circuits.     

Hydrated Mn(IV) oxide-exfoliated graphite composites for electrochemical capacitor

Commercially available low cost exfoliated graphite (EG, nominal diameter 130 μm) was used as a conductive substrate for electrochemical capacitor of hydrated Mn(IV) oxide, MnO₂·nH₂O. The MnO₂·nH₂O-EG composites were prepared by addition of EG to potassium permanganate solution, followed by 1 h stirring and then slow addition of manganese(II) acetate solution. By this procedure submicrometer or smaller sized MnO₂·nH₂O particles having mesopores of 6-12 nm in diameter were formed on the graphite sheets of EG. Although EG alone showed only about 2 F g⁻¹, the composites showed good rectangular cyclic voltammograms at 2-20 mV s⁻¹ in 1 mol L⁻¹ Na₂SO₄. The capacitance per net amount of MnO₂ increased proportionally with EG content, that is, utilization ratio of MnO₂ increased with EG content. The composites of MnO₂·nH₂O and smaller diameter of EG (nominal diameter 45 μm) or artificial graphite powder (average diameter 3.7 μm) showed fairly good performance at 2 mV s⁻¹, but with increasing potential scan rate the rectangular shape was distorted and capacitance decreased drastically. The results implies that sheet-like structure is more effective than small particles as conductive materials, when the formation procedure of composite is the same. Large sized EG may be a promising conductive material for electrochemical capacitors.     

Electrosynthesis and efficient electrocatalytic performance of poly(neutral red)/ordered mesoporous carbon composite

A novel composite film which contains ordered mesoporous carbon (OMC) along with the incorporation of poly(neutral red) (PNR) has been synthesized on glassy carbon electrode by potentiostatic method. This composite film was characterized by scanning electron microscope (SEM) and cyclic voltammetry (CV). Two pairs of the redox peaks appear at formal potential E^0′ = +0.045 V (peak I) and E^0′ = −0.49 V (peak II) at the PNR/OMC/GC electrode. And it is found that only the redox waves (peak I) exhibits good electrocatalytic activity towards nicotinamide adenine dinucleotide (NADH) and 2-mercaptoethanol (2-ME). Under a lower operation potential of +0.07 V, amperometry method was used to determine the concentration of NADH and 2-ME, respectively. In pH 7.0, sensors for two molecules under their corresponding optimized conditions were developed with acceptable sensitivity and low detection limits in large determination ranges. In addition, these sensors have good reproducibility and stability.     

Preparation and capacitive properties of cobalt-nickel oxides/carbon nanotube composites

In this paper, nickel-cobalt oxides/carbon nanotube (CNT) composites were prepared by adding and thermally decomposing nickel and cobalt nitrates directly onto the surface of carbon nanotube/graphite electrode to form nickel and cobalt oxides. Carbon nanotubes used in this paper were grown directly on graphite substrate by chemical vapor deposition technique. The capacitive behavior of nickel-cobalt oxides/CNT electrode was investigated by cyclic voltammetry and galvanostatic charge-discharge method in 1 M KOH aqueous solutions. The results show that nickel-cobalt oxides/CNT composite electrode has excellent charge-discharge cycle stability (0.2% and 3.6% losses of the specific capacitance are found at the 1000th and 2000th charge-discharge cycles, respectively) and good charge-discharge properties at high currrent density. Additionally, the effect of Ni/Co molar ratio on specific capacitance of the composite electrode was investigated and the highest specific capacitance (569 F g⁻¹ at 10 mA cm⁻²) is obtained at Ni/Co molar ratio = 1:1.