One-step microwave synthesis and characterization of carbon-modified nanocrystalline LiFePO4

The precursors of LiFePO₄ were prepared by a sol-gel method using lithium acetate dihydrate, ferrous sulfate, phosphoric acid, citric acid and polyethylene glycol as raw materials, and then the carbon-modified nanocrystalline LiFePO₄ (LiFePO₄/C) cathode material was synthesized by a one-step microwave method with the domestic microwave oven. The effect of microwave time and carbon content on the performance of the resulting LiFePO₄/C material was investigated. Structural characterization by X-ray diffraction and scanning electron microscopy proved that the olivine phase LiFePO₄ was synthesized and the grain size of the samples was several hundred nanometers. Under the optimal conditions of microwave time and carbon content, the charge-discharge performance indicated that the nanosized LiFePO₄/C had a high electrochemical capacity at 0.2 C (152 mAh g⁻¹) and improved capacity retention; the exchange current density was 1.6977 mA cm⁻². Furthermore, the rate capability was improved effectively after LiFePO₄ was modified with carbon, with 59 mAh g⁻¹ being obtained at 20 C.     

Improving the rate performance of LiFePO4 by Fe-site doping

LiFePO₄ doped by bivalent cation in Fe-sites show improved rate performance and cyclic stability. Under 10 C rate at room temperature, the capacities of LiFe_0.9M_0.1PO₄ (M = Ni, Co, Mg) maintain at 81.7, 90.4 and 88.7 mAh/g, respectively, in comparison with 53.7 mAh/g for undoped LiFePO₄ and 54.8 mAh/g for carbon-coated LiFePO₄ (LiFePO₄/C). The capacity retention is 95% after 100 cycles for doped samples while this value is only 70% for LiFePO₄ and LiFePO₄/C. Such a significant improvement in electrochemical performance should be partially related to the enhanced electronic conductivities (from 2.2 × 10⁻⁹ to <2.5 × 10⁻⁷ S cm⁻¹) and probably the mobility of Li⁺ ions in the doped samples.     

Electrochemical properties of carbon-mixed LiFePO4 cathode material synthesized by the ceramic granulation method

LiFePO₄/carbon composite cathode material was prepared using polyvinyl alcohol (PVA) as carbon source by pelleting and subsequent pyrolysis in N₂. The samples were characterized by XRD, SEM and TGA. Their electrochemical performance was investigated in terms of charge–discharge cycling behavior. It consists of a single LiFePO₄ phase and amorphous carbon. The special micro-morphology via the process is favorable for electrochemical properties. The discharge capacity of the LiFePO₄/C composite was 145 mAh/g, closer to the theoretical specific capacity of 170 mAh/g at 0.1 C low current density. At 3 C modest current density, the specific capacity was about 80 mAh/g, which can satisfy for transportation applications if having a more planar discharge flat.     

LiFePO4 cathode power with high energy density synthesized by water quenching treatment

A water quenching (WQ) method was developed to synthesize LiFePO₄ and C-LiFePO₄. Our results indicate that this synthesis method ensures improved electrochemical activity and small crystal grain size. The synthetic conditions were optimized using orthogonal experiments. The LiFePO₄ sample prepared at the optimized condition showed a maximum discharge capacity of 149.8 mAh g⁻¹ at a C/10 rate. C-LiFePO₄ with a low carbon content of 0.93% and a high discharge specific capacity of 163.8 mAh g⁻¹ has also been obtained using this method. Water quenching treatment shows outstanding improvement of the electrochemical performance of LiFePO₄.     

Improved electrochemical performance of LiFePO4 by increasing its specific surface area

Cathode material LiFePO₄ with an excellent rate capability has been successfully prepared by a simple solid state reaction method using LiCH₃COO·2H₂O, FeC₂O₄·2H₂O and (NH₄)₂HPO₄ as the starting materials. We have investigated the effects of the sintering temperature and mixing time of the starting materials on the physical properties and electrochemical performance of LiFePO₄. It was found that the rate capability of LiFePO₄ is mainly controlled by its specific surface area and it is an effective way to improve the rate capability of the sample by increasing its specific surface area. In the present study, our prepared LiFePO₄ with a high specific surface area of 24.1 m² g⁻¹ has an excellent rate capability and can deliver 115 mAh g⁻¹ of reversible capacity even at the 5 C rate. Moreover, we have prepared lithium ion batteries based on LiFePO₄ as the cathode material and MCMB as the anode material, which showed an excellent cycling performance.     

Optimization of electrochemical properties of LiFePO4/C prepared by an aqueous solution method using sucrose

LiFePO₄ can be used as a positive electrode material for lithium-ion batteries by making composite with electrical conductive carbonaceous materials. In this study, LiFePO₄/C (carbon) composite was prepared by a soft chemistry route, in which sucrose was used as a carbon source of a low price. We tried to optimize a Li/(LiFePO₄/C) cell performance through changing synthetic conditions and discussed the factors affecting the electrochemical performances of the cell, such as the amount of the carbon source, synthetic temperature, gas flow rate of pyrolysis and the formation of secondary phases. It was found that the connection of the residual carbon and Fe₂P to LiFePO₄ particles and the amount of these two phases were important factors. In our experimental conditions, LiFePO₄/C including 9.72 wt.% of residual carbon, prepared at 800 °C for 12 h showed the highest reversible capacity and the best C rate performance among the synthesized materials; 130 mAh g⁻¹ at 10C rate and 50 °C.     

Emulsion drying synthesis of olivine LiFePO4/C composite and its electrochemical properties as lithium intercalation material

The electroactive LiFePO₄/C nano-composite has been synthesized by an emulsion drying method. During burning-out the oily emulsion precipitates in an air-limited atmosphere at 300 °C, amorphous or low crystalline carbon was generated along with releasing carbon oxide gases, and trivalent iron as a cheap starting material was immediately reduced to the divalent one at this stage as confirmed by X-ray photoelectron spectroscopy, leading to a low crystalline LiFePO₄/C composite. Heat-treatment of the low crystalline LiFePO₄/C in an Ar atmosphere resulted in a well-ordered olivine structure, as refined by Rietveld refinement of the X-ray diffraction pattern. From secondary electron microscopic and scanning transmission electron microscopic observations with the corresponding elemental mapping images of iron and phosphorous, it was found that the LiFePO₄ powders are modified by fine carbon. The in situ formation of the nano-sized carbon during crystallization of LiFePO₄ brought about two advantages: (i) an optimized particle size of LiFePO₄, and (ii) a uniform distribution of fine carbon in the product. These effects of the fine carbon on LiFePO₄/C composite led to high capacity retention upon cycling at 25 and 50 °C and high rate capability, resulting from a great enhancement of electric conductivity as high as 10⁻⁴ S cm⁻¹. That is, the obtained capacity was higher than 90 mAh (g-phosphate)⁻¹ by applying a higher current density of about 1000 mA g⁻¹ (11 C) at 50 °C.     

Enhanced electrochemical performance of nano-sized LiFePO4/C synthesized by an ultrasonic-assisted co-precipitation method

A simple and effective method, the ultrasonic-assisted co-precipitation method, was employed to synthesize nano-sized LiFePO₄/C. A glucose solution was used as the carbon source to produce in situ carbon to improve the conductivity of LiFePO₄. Ultrasonic irradiation was adopted to control the size and homogenize the LiFePO₄/C particles. The sample was characterized by X-ray powder diffraction, field-emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM) and high-resolution transmission electron microscopy (HRTEM). FE-SEM and TEM show that the as-prepared sample has a reduced particle size with a uniform size distribution, which is around 50 nm. A uniform amorphous carbon layer with a thickness of about 4-6 nm on the particle surface was observed, as shown in the HRTEM image. The electrochemical performance was demonstrated by the charge-discharge test and electrochemical impedance spectra measurements. The results indicate that the nano-sized LiFePO₄/C presents enhanced discharge capacities (159, 147 and 135 mAh g⁻¹ at 0.1, 0.5 and 2 C-rate, respectively) and stable cycling performance. This study offers a simple method to design and synthesis nano-sized cathode materials for lithium-ion batteries.     

Enhanced electrochemical performance of carbon nanospheres-LiFePO4 composite by PEG based sol-gel synthesis

The carbon nanospheres-LiFePO₄ (CNSs-LiFePO₄) composite has been synthesized by PEG (polyethylene glycol, mean molecular weight of 30,000) based sol-gel route. Highly conductive CNSs (30-40 nm) were adopted to improve the electronic conductivity of LiFePO₄. PEG was used to promote the dispersion of CNSs with the surface functionalization of CNSs, which could facilitate the coating of CNSs on the surface of the LiFePO₄ particles. The sample was characterized by X-ray diffraction, field emission scanning electron microscopy, transmission electron microscopy, and Raman scattering. Electrochemical performance of the CNSs-LiFePO₄ composite was characterized by the charge-discharge test and electrochemical impedance spectra measurement. The results indicated that LiFePO₄ particles were well coated with the conductive CNSs to overcome the intrinsic low electronic conductivity problem of LiFePO₄. The CNSs-LiFePO₄ composite delivered an enhanced rate capability (146, 128 and 113 mAh g⁻¹ at 0.1 C, 1 C and 5 C rate). The PEG based sol-gel route enables LiFePO₄ networked with CNSs, which offered a higher electrochemical performance.     

In situ construction of carbon nano-interconnects between the LiFePO4 grains using ultra low-cost asphalt

LiFePO₄/C composite cathode materials with carbon nano-interconnect structures were synthesized by one-step solid state reaction using low-cost asphalt as both carbon source and reducing agent. Based on the thermogravimetry, differential scanning calorimetry, transmission electron microscopy and high-resolution transmission electron microscopy, a growth model was proposed to illustrate the formation of the carbon nano-interconnect between the LiFePO₄ grains. The LiFePO₄/C composite shows enhanced discharge capacity (150 mAh g⁻¹) with excellent capacity retention compared with the bare LiFePO₄ (41 mAh g⁻¹) due to the electronically conductive nanoscale networking provided by the asphalt-based carbon. The results prove that the asphalt is a perfect carbon source and reduction agent for cost-effective production of high performance LiFePO₄/C composite.     

Rechargeable Li/LiFePO4 cells using N-methyl-N-butyl pyrrolidinium bis(trifluoromethane sulfonyl)imide-LiTFSI electrolyte incorporating polymer additives

We have incorporated polymer additives such as poly(ethylene glycol) dimethyl ether (PEGDME) and tetra(ethylene glycol) dimethyl ether (TEGDME) into N-methyl-N-butylpyrrolidinium bis(trifluoromethane sulfonyl)imide (PYR₁₄TFSI)-LiTFSI mixtures. The resulting PYR₁₄TFSI + LiTFSI + polymer additive ternary electrolyte exhibited relatively high ionic conductivity as well as remarkably low viscosity over a wide temperature range compared to the PYR₁₄TFSI + LiTFSI binary electrolytes. The charge/discharge cyclability of Li/LiFePO₄ cells containing the ternary electrolytes was investigated. We found that Li/PYR₁₄TFSI + LiTFSI + PEGDME (or TEGDME)/LiFePO₄ cells containing the two different polymer additives showed very similar discharge capacity behavior, with very stable cyclability at room temperature (RT). Li/PYR₁₄TFSI + LiTFSI + TEGDME/LiFePO₄ cells can deliver about 127 mAh/g of LiFePO₄ (74.7% of theoretical capacity) at 0.054 mA/cm² (0.2C rate) at RT and about 108 mAh/g of LiFePO₄ (63.4% of theoretical capacity) at 0.023 mA/cm² (0.1C rate) at −1 °C for the first discharge. The cell exhibited a capacity fading rate of approximately 0.09-0.15% per cycle over 50 cycles at RT. Consequently, the PYR₁₄TFSI + LiTFSI + polymer additive ternary mixture is a promising electrolyte for cells using lithium metal electrodes such as the Li/LiFePO₄ cell reported here. These cells showed the capability of operating over a significant temperature range (∼0-∼30 °C).     

Synthesis and characterization of high-density LiFePO4/C composites as cathode materials for lithium-ion batteries

To achieve a high-energy-density lithium electrode, high-density LiFePO₄/C composite cathode material for a lithium-ion battery was synthesized using self-produced high-density FePO₄ as a precursor, glucose as a C source, and Li₂CO₃ as a Li source, in a pipe furnace under an atmosphere of 5% H₂-95% N₂. The structure of the synthesized material was analyzed and characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM). The electrochemical properties of the synthesized LiFePO₄/carbon composite were investigated by cyclic voltammetry (CV) and the charge/discharge process. The tap-density of the synthesized LiFePO₄/carbon composite powder with a carbon content of 7% reached 1.80 g m⁻³. The charge/discharge tests show that the cathode material has initial charge/discharge capacities of 190.5 and 167.0 mAh g⁻¹, respectively, with a volume capacity of 300.6 mAh cm⁻³, at a 0.1C rate. At a rate of 5C, the LiFePO₄/carbon composite shows a high discharge capacity of 98.3 mAh g⁻¹ and a volume capacity of 176.94 mAh cm⁻³.     

Process investigation, electrochemical characterization and optimization of LiFePO4/C composite from mechanical activation using sucrose as carbon source

LiFePO₄/C composite was synthesized by mechanical activation using sucrose as carbon source. High-energy ball milling facilitated phase formation during thermal treatment. TG-DSC and TPR experiments demonstrated sucrose was converted to CH_x intermediate before completely decomposed to carbon. Ball milling time, calcination temperature and dwelling time all had significant impact on the discharge capacity and rate performance of the resulted power. The optimal process parameters are high-energy ball milling for 2-4 h followed by thermal treatment at 700 °C for 20 h. The product showed a capacity of 174 mAh/g at 0.1C rate and around 117 mAh/g at 20C rate with the capacity fade less than 10% after 50 cycles. Too low calcination temperature or insufficient calcination time, however, could result in the residual of CH_x in the electrode and led to a decrease of electrode performance.     

Synthesis and characterization of LiFePO4/(Ag + C) composite cathodes with nano-carbon webs

LiFePO₄/(Ag + C) composite cathodes with a new type of nano-sized carbon webs were synthesized by two methods of an aqueous co-precipitation and a sol-gel process, respectively. Simultaneous thermogravimetric-differential thermal analysis indicates that the crystallization temperature of LiFePO₄ is about 455-466 °C, which is close to the pyrolysis temperature of polypropylene, 460 °C. The silver and carbon co-modifying does not affect the olivine structure of LiFePO₄ but improves its kinetics in terms of discharge capacity and rate capability. Discharge capacities were improved from 153.4 mA h g^− 1 of LiFePO₄/C to 160.5 mA h g^− 1and 162.1 mA h g^− 1 for LiFePO₄/(Ag + C) cathodes synthesized by the co-precipitation and sol-gel methods, respectively. The possible reasons for the small difference in discharge capacity of two LiFePO₄/(Ag + C) cathodes were discussed. AC impedance measurements show that the Ag + C co-modification decreases the charge transfer resistance of LiFePO₄/(Ag + C) cathodes.     

Preparation and characterization of nano-sized LiFePO4 by low heating solid-state coordination method and microwave heating

The precursors of LiFePO₄ were prepared by low heating solid-state coordination method using lithium acetate, ammonium dihydric phosphate, ferrous oxalate and citric acid as raw materials. Olivine phase LiFePO₄ as a cathode material for lithium-ion batteries was successfully synthesized by microwave heating in a few minutes. X-ray diffraction (XRD) and transmission electron microscope (TEM) were used to characterize its structure and morphology. Cyclic voltammetry (CV) and charge-discharge cycling performance were used to characterize its electrochemical properties. The results showed that the grain size of the optimal sample was about 40-50 nm, and the as-prepared particles were homogeneous. The nano-sized LiFePO₄ obtained has a high electrochemical capacity (125 mAh g⁻¹) and stable cycle ability.     

Preparation and characterization of nano-particle LiFePO4 and LiFePO4/C by spray-drying and post-annealing method

Pure, nano-sized LiFePO₄ and LiFePO₄/C cathode materials are synthesized by spray-drying and post-annealing method. The influence of the sintering temperature and carbon coating on the structure, particle size, morphology and electrochemical performance of LiFePO₄ cathode material is investigated. The optimum processing conditions are found to be thermal treatment for 10 h at 600 °C. Compared with LiFePO₄, LiFePO₄/C particles are smaller in size due to the inhibition of crystal growth to a great extent by the presence of carbon in the reaction mixture. And that the LiFePO₄/C composite coated with 3.81 wt.% carbon exhibits the best electrode properties with discharge capacities of 139.4, 137.2, 133.5 and 127.3 mAh g⁻¹ at C/5, 1C, 5C and 10C rates, respectively. In addition, it shows excellent cycle stability at different current densities. Even after 50 cycles at the high current density of 10C, a discharge capacity of 117.7 mAh g⁻¹ is obtained (92.4% of its initial value) with only a low capacity fading of 0.15% per cycle.     

Influence of carbon sources on LiFePO4/C composites synthesized by the high-temperature high-energy ball milling method

Carbon-coated LiFePO₄ composites were synthesized by a new method of high-temperature high-energy ball milling (HTHEBM). Fe₂O₃ and LiH₂PO₄ were used as raw materials. Glucose, sucrose, citric acid and active carbon were used as reducing agents and carbon sources, respectively. In this method, high-energy ball milling and carbon coating worked together and, therefore, fine and homogeneous LiFePO₄/C particles with excellent properties were obtained in a relatively short synthesis time of 9 h. Moreover, the synthesis process could be completely finished at a relatively lower temperature of 600 °C for high-energy ball milling transforming mechanical energy into thermal energy. The results of X-ray diffraction (XRD) analysis, scanning electron microscopy (SEM), transmission electron microscopy (TEM) and electrochemical performance tests indicated that carbon source had an important influence on the properties of LiFePO₄/C composites synthesized by the HTHEBM method. It was proved that the LiFePO₄ composites coated with glucose had the best properties with 1 μm geometric mean diameter and 150.3 mA h g⁻¹ initial discharge capacity at a current rate of 0.1 C. After the 20th cycle test, the reversible capacity was 148 mA h g⁻¹ at 0.1 C, showing a retention ratio to the initial capacity of 98.5%.     

Carbon coated Li3V2(PO4)3 cathode material prepared by a PVA assisted sol-gel method

Carbon coated Li₃V₂(PO₄)₃ cathode material was prepared by a poly(vinyl alcohol) (PVA) assisted sol-gel method. PVA was used both as the gelating agent and the carbon source. XRD analysis showed that the material was well crystallized. The particle size of the material was ranged between 200 and 500 nm. HRTEM revealed that the material was covered by a uniform surface carbon layer with a thickness of 80 Å. The existence of surface carbon layer was further confirmed by Raman scattering. The electrochemical properties of the material were investigated by charge-discharge cycling, CV and EIS techniques. The material showed good cycling performance, which had a reversible discharge capacity of 100 mAh g⁻¹ when cycled at 1 C rate. The apparent Li⁺ diffusion coefficients of the material ranged between 9.5 × 10⁻¹⁰ and 0.9 × 10⁻¹⁰ cm² s⁻¹, which were larger than those of olivine LiFePO₄. The large lithium diffusion coefficient of Li₃V₂(PO₄)₃ has been attributed to its special NASICON-type structure.     

Comparative studies on C-coated and uncoated LiFePO4 cycling at various rates and temperatures using synchrotron based in situ X-ray diffraction

The structural changes of LiFePO₄ and C-coated LiFePO₄ during charging at various C-rates and temperatures are investigated using synchrotron based in situ X-ray diffraction technique. The XRD patterns collected during cycling show the structural evidence of the positive effects of carbon coating on LiFePO₄ for the electrochemical performance improvements at different temperatures, especially at low temperatures. At −10 °C, the C-coated LiFePO₄ shows comparable capacities with the sample cycled at room temperature when cycled at C/5 rate with a slight shift of the plateau to a higher voltage during charging. The in situ XRD patterns collected simultaneously show a complete phase transformation from triphylite to heterosite. At −20 °C, the C-coated LiFePO₄ delivers 55.6% of its theoretical capacities at C/5 rate. However, the plateau in the charging curve becomes sloppy and shifts to a higher voltage. The in situ XRD patterns show that the phase transformation from triphylite to heterosite is not completed when charged to 4.5 V due to the larger polarization when charged at −20 °C.     

Effect of milling method and time on the properties and electrochemical performance of LiFePO4/C composites prepared by ball milling and thermal treatment

Effects of ball milling way and time on the phase formation, particulate morphology, carbon content, and consequent electrode performance of LiFePO₄/C composite, prepared by high-energy ball milling of Li₂CO₃, NH₄H₂PO₄, FeC₂O₄ raw materials with citric acid as organic carbon source followed by thermal treatment, were investigated. Three ball milling ways and five different milling durations varied from 0 to 8 h were compared. LiFePO₄/C composites could be obtained from all synthesis processes. TEM examinations demonstrated LiFePO₄/C from ball milling in acetone resulted in sphere shape grains with a size of ∼60 nm, similar size was observed for LiFePO₄/C from dry ball milling but in a more irregular shape. The ball milling in benzene resulted in a much larger size of ∼250 nm. The LiFePO₄/C composites prepared from dry ball milling and ball milling in acetone showed much better electrochemical performance than that from ball milling in benzene. SEM examinations and BET measurements demonstrated that the high-energy ball milling effectively reduced the grain size. A ball milling for 4 h resulted in the best electrochemical performance, likely due to the proper amount of carbon and proper carbon structure were created.