基于滑模观测器的永磁同步电机模型预测电流控制研究

针对永磁同步电机无位置传感器高动态性能控制问题,对传统矢量控制存在电流内环PI控制器对系统性能的影响以及传统滑模观测器中动态转子位置角估计不准、稳态转速估计不精确等观测器性能进行了改进,提出了一种基于改进滑模观测器的永磁同步电机模型预测电流控制方法。根据永磁同步电机在同步旋转坐标系下的数学模型,选择了电机d、q电流作为状态变量,利用前向欧拉法推导出永磁同步电机d、q轴电流的预测模型。通过实时评估价值函数选出使得下一时刻电流跟踪效果最好的电压矢量,将其对应的开关状态作用于逆变器。同时,推导表贴式永磁同步电机的滑模观测器模型并对其观测出的转子位置角和转速进行补偿,得到较为精确的估算值。最后将算法在Matlab/Simulink进行了仿真试验。研究结果表明:所提出的控制方法动态性能好、稳态精度高。     

一种新型永磁同步电机高阶滑模转速观测器的研究

针对面贴式永磁同步电机无位置传感器速度控制系统存在的速度检测延迟、检测误差较大、动态响应不够快等问题,对永磁同步电机无位置传感器速度控制系统模型和传统滑模速度观测器结构和原理进行了分析,对高阶滑模算法理论进行了推导,结合永磁同步电机数学模型,提出了一种以位置信号为滑模变量,以高阶滑模变结构算法为基础的新型滑模转速观测器,利用Simulink软件构建了基于新型滑模速度观测器永磁同步电机矢量控制系统,对电机的起动特性、速度跟踪特性、抗外界干扰性能进行了研究。研究结果表明,由于新的滑模观测器将转子位置与反电势信号的关系进行了分离,消除了反电势信号处理滤波器对速度估算的延迟,提高了速度检测精度,从而改善了系统的稳态和动态性能。     

基于自适应观测器的复式永磁同步电机控制仿真

为了解决复式永磁同步电机(PMSM)的可靠运行及速度控制等问题.提出了一种基于自适应观测器的无传感器控制方案.利用Matlab这一工具搭建了复式永磁同步电机的自适应观测器的控制仿真模型,并对算法进行了分析验证,同时为了提高该系统的稳定性,对电机的电阻和磁链也进行了参数辨识.仿真运行的结果验证了自适应观测器作为复式水磁同...     

基于扰动观测器的永磁同步电机电流环自适应滑模控制

针对扰动对永磁同步电机转速伺服系统性能的影响,提出了基于扰动观测器的电流环自适应滑模控制方法。设计了自适应律在线估计系统的内部参数摄动以补偿模型不确定性扰动。同时,设计了滑模扰动观测器实时估计系统外部负载扰动,并将观测值前馈补偿到电流环自适应滑模控制器,在提高系统鲁棒性的同时降低滑模控制系统的抖振。实验结果显示,采用基于扰动观测器的电流环自适应滑模控制方法,系统可快速、准确、无超调地跟踪900r/min的速度指令,调节时间为0.08s,稳态误差为±5r/min。加入0.6N·m的负载扰动,该控制方法的最大转速波动为21r/min,比PI控制方法的转速波动减小了3.4%。仿真和实验结果表明,基于扰动观测器的电流环自适应控制方法提高了永磁同步电机转速伺服系统的鲁棒性和动态响应性能,同时可有效抑制滑模控制系统的抖振。     

电动汽车永磁同步电机无位置传感器控制的研究

针对电动汽车永磁同步电机无位置传感器控制系统,在两相静止坐标系（d—B）内将滑模观测器法与MRAS结合,提出了基于模型参考自适应的滑模观测器,并利用自适应律估计永磁同步电机的转子速度。仿真和试验表明无位置传感器控制方法是切实可行的。     

直联压缩机两种不同控制方法的比较研究

建立了空压机的负载数学模型,对其负载进行了分析。建立了永磁同步电机的数学模型,给出了一种用于交流永磁同步电机速度控制的滑模控制器。根据永磁同步电机的控制特点和空压机负载特点进行Simulink仿真,仿真结果表明,加滑模控制器时,电机转速波动较小。最后,对用永磁同步电机驱动直联便携式空压机做实验。实验结果表明,与常规的PI控制策略相比,滑模变结构控制改善了系统的动态性能,有较强的鲁棒性。永磁同步电机驱动空压机效率高,转速波动小。     

自适应车用永磁同步电机在线参数辨识

车用永磁同步电机在运行过程中复杂的工况和恶劣的工作条件会影响电机的参数进而影响电机控制性能。本文采用自适应的参数辨识算法,对永磁同步电机参数进行在线辨识并反馈回电机控制系统,改进原有控制参数。该算法基于永磁同步电机的数学模型,根据转速电流反馈信号,借助Lyapunov稳定理论建立负载转矩和交直轴电感的辨识模型并推导其自适应律。基于MTPA算法的仿真和实验结果表明本文提出的参数辨识算法能够在较短时间内实现高效的参数辨识,且估计值与真实值的误差较小。     

基于负载观测器的PMSM分数阶滑模位置控制

针对永磁同步电机位置控制系统,设计分数阶滑模变结构控制器,以代替传统PID三闭环串级控制结构的转速环和位置环控制器。针对电机运行时负载转矩会受到外界干扰的问题,设计负载转矩观测器。仿真结果表明分数阶滑模控制器有良好的动态和稳态性能以及良好的鲁棒性。     

周视扫描成像系统的转台转速高精度控制

为实现基于转台的像移补偿型周视扫描成像系统的高分辨率稳定成像,提出了一种复合控制算法对永磁同步电机驱动的扫描转台进行转速跟踪控制。根据转台的载荷特点及电机的数学模型,建立了包含机械参数不确定性和快变转矩扰动的单采样率控制系统模型;采用快速非奇异终端滑模和扩张高增益观测器复合控制实现了转速跟踪控制;采用快速非奇异终端滑模实现了最大转矩电流比控制;最后,分析并验证了基于上述复合算法的转速跟踪控制性能。实验表明:在转台转速设定为120 r/min或240 r/min时,采用该复合算法的转速跟踪误差均小于0.1%。与PI控制、快速非奇异终端滑模控制及线性滑模+观测器控制相比,采用该复合算法的转台转速响应具有无超调、抗扰动性能更强、跟踪精度更高的优点,能保证所述周视成像系统获得清晰稳定的周视全景图像。     

基于MRAS的新型永磁同步电机的速度辨识方案

速度辨识一直是永磁同步电机无速度传感器控制系统中的一个核心问题,本文以永磁同步电机本身为参考模型,变换数学模型构造并联模型,并由转矩和转速的基本的机械运动方程和转矩方程推导出速度辨识率,结合模型参考自适应控制理论得到速度辨识方案。本方案控制过程简单,对电机参数不敏感,并将其应用在永磁同步电机矢量控制系统当中,仿真得到的结果验证了本方案的正确性和可行性,同时,与基于POPOV理论的模型参考自适应方案的仿真结果进行比较,分析本方案的优劣。     

Minimal Realization of Linear Graph Models for Multi-physics Systems

An engineering system may consist of several different types of components,belonging to such physical"domains"as mechanical,electrical,fluid,and thermal.It is t...     

INTEGRAL EQUATION METHOD＇S APPLICATION IN HOLE-EDGE STRESS OF COMPOSITE MATERIAL PLATE WITH DIFFERENT SHAPED HOLES

The strength of composite plate with different hole-shapes is always one of the most important but complicated issues in the application of the composite material. The holes will lead to mutations and discontinuity to the structure. So the hole-edge stress concentration is always a serious phenomenon. And the phenomenon makes the structure strength decrease very quickly to form dangerous weak points. Most partial damage begins from these weak points. According to the complex variable functions theory, the accurate boundary condition of composite plate with different hole-shapes is founded by conformal mapping method to settle the boundary condition problem of complex hole-shapes. Composite plate with commonly hole-shapes in engineering is studied by several complex variable stress fimction. The boundary integral equations are founded based on exact boundary conditions. Then the exact hole-edge stress analytic solution of composite plate with rectangle holes and wing manholes is resolved. Both of offset axis loadings and its influences on the stress concentration coefficient of the hole-edge are discussed. And comparisons of different loads along various offset axis on the hole-edge stress distribution of orthotropic plate with rectangle hole or wing manhole are made. It can be concluded that hole-edge with continuous variable curvatures might help to decrease the stress concentration coefficient; and smaller angle of outer load and fiber can decrease the stress peak value.     

Non-monotonic material contrast in scanning ion and scanning electron images

30 keV Ga⁺ focused ion beam induced secondary electron (iSE) imaging was used to determine the relative contrast between several materials. The iSE signal compared from C, Si, Al, Ti, Cr, Ni, Cu, Mo, Ag, and W metal layers does not decrease with an increase in target atomic number Z₂, and shows a non-monotonic relationship between contrast and Z₂. The non-monotonic relationship is attributed to periodic fluctuations of the stopping power and sputter yield inherent to the ion–solid interactions. In addition, material contrast from electron-induced secondary electron (eSE) and backscattered electron (BSE) images using scanning electron microscopy (SEM) also shows non-monotonic contrast as a function of Z₂, following the periodic behavior of the stopping power for electron–solid interactions. A comparison of the iSE and eSE results shows similar relative contrast between the metal layers, and not complementary contrast as conventionally understood. These similarities in the contrast behavior can be attributed to similarities in the periodic and non-monotonic function defined by incident particle–solid interaction theory.     

Application of Feature Extraction through Convolution Neural Networks and SVM Classifier for Robust Grading of Apples

This paper proposes a novel grading method of apples,in an automated grading device that uses convolutional neural networks to extract the size,color,texture,an...     

分布动态载荷识别的抗噪处理

针对正交多项式频域法在用多种响应对矩形薄板进行载荷识别中抗噪性较差的问题,综合运用平均法、矩阵预处理和奇异值截断法等方法对之进行改善,并引入空间映射的思想,将该方法的应用范围拓展为复杂的模型.利用仿真算例,证实了该方法具有较好的抗噪性.     

基于MELTAC-N平台的核电厂安全级DCS环网研究与测试

针对工程实践中环网通讯相关问题的处理缺乏理论基础及国产化安全级DCS平台的开发缺乏成熟经验借鉴问题,对基于MELTAC-N平台核电厂安全级DCS环网的软硬件实现进行了研究。提出了安全级DCS环网双环网冗余设计、光切换开关设计等硬件设计方法,以及以RPR协议为基础,采用全数据收发策略的软件设计方法。在CPR1000安全级DCS平台上对安全级DCS环网的可靠性及实时性进行了评价,并进行了容错能力、响应时间及响应时间稳定性测试验证实验。结果表明,基于MELTAC-N平台安全级DCS环网软硬件设计具有较好的容错能力及响应时间稳定性。     

Short-Term Relay Quality Prediction Algorithm Based on Long and Short-Term Memory

The fraction defective of semi-finished products is predicted to optimize the process of relay production lines, by which production quality and productivity ar...     

End-to-End Multiview Gesture Recognition for Autonomous Car Parking System

The use of hand gestures can be the most intuitive human-machine interaction medium.The early approaches for hand gesture recognition used device-based methods....     

The laboratory simulation of abrasive wear

Abrasive wear has long been recognised as one of the most potentially serious tribological problems facing the operators of many types of plant and machinery; several industrial surveys have indicated that wear by abrasion can be responsible for more than 50% of unscheduled machine and plant stoppages. Locating the operating point of a tribological contact in an appropriate operational ‚map’︁ can provide a useful guide to the likely nature and origins of the surface degradation experienced in use, though care must be exercised in choosing the most suitable parameters for the axes of the plot. Laboratory testing of materials and simulations of machine contacts are carried out for a number of purposes; at one level for the very practical aims of ranking candidate materials or surface hardening treatments in order of their wear resistance, or in an attempt to predict wear lives under field conditions. More fundamentally, tests may be aimed at elucidating the essential physical mechanisms of surface damage and loss, with the longer term aim of building an analytical and predictive model of the wear process itself. In many cases, component surface damage is brought about by the ingress of hard, particulate matter into machine bearing or sealing clearances. These may be running dry although, more usually, a lubricant or service fluid is present at the interface. A number of standardised wear test geometries and procedures have been established for both two- and three-body wear situations, and these are briefly described. Although abrasive wear is often modelled as following an ‚Archard’︁ equation (i.e. a linear increase in material loss with both load and time, and an inverse dependence on specimen hardness) both industrial experience and laboratory tests of particularly lubricated contacts show that this is not always the case: increasing the hardness differential in an abrasively contaminated lubricated pair may not always reduce the rate of damage to the harder surface.     

Limits of topographic measurement by the scanning tunnelling and atomic force microscopes

Parameters describing the topographic character of a surface (height, surface wavelength, slope and curvature) can be derived from equivalent sinusoidal profiles. The response of a surface-measuring instrument may be modelled in terms of instrument parameters such as stylus radius, and scanning range and resolution. The performance of the instrument may then be mapped as a zone in amplitude-wavelength (AW) space to show the sinusoidal profiles it is capable of measuring. In a first-order analysis the STM and AFM are considered as equivalent to contact-stylus instruments with a notional stylus radius equal to the tip radius plus the gap. Comparisons between different instruments and types of instrument are readily made by mapping in AW space. The error arising from convolution of the sinusoidal profile with that of the finite tip may be quantified and plotted as contours in AW space.