A reconfigurable passive mixer for multimode multistandard receivers in 0.18 μm CMOS

This paper presents a reconfigurable quadrature passive mixer for multimode multistandard receivers. By using controllable transconductor and transimpedance-amplifier stages, the voltage conversion gain of the mixer is reconfigured according to the requirement of the selected communication standard Other characteristics such as noises figure, linearity and power consumption are also reconfigured consequently. The design concept is verified by implementing a quadrature passive mixer in 0.18 μm CMOS technology. On wafer measurement results show that, with the input radio frequency ranges from 700 MHz to 2.3 GHz, the mixer achieves a controllable voltage conversion gain from 4 to 22 dB with a step size of 6 dB. The measured maximum ⅡP3 is 8.5 dBm and the minimum noise figure is 8.0 dB. The consumed current for a single branch (I or Q) ranges from 3.1 to 5.6 mA from a 1.8 V supply voltage. The chip occupies an area of 0.71 mm² including pads.     

Nonlinear diffusion for orientation estimation

This letter presents an image orientation estimation method which is based on a combination of two techniques： quadrature filtering and nonlinear diffusion. The quadrature filters are used to get the orientation tensors for edges, then the orientation tensors are smoothed through nonlinear diffusion. Experimental resuits and analysis show the robustness of the proposed method.     

应用于DRM/DAB系统的高转换增益及线性度优化的新结构混频器

This paper focuses on a new design of a down-conversion mixer for a low-IF wideband receiver.Based on the folded structure and differential multiple gated transistor(DMGTR) technique,a novel quadrature mixer with a high conversion gain,a moderate linearity,and a moderate NF is proposed.The mixer is designed and implemented in a 0.18-m CMOS process,and can operate in a frequency range from 150 kHz to 1.5 GHz.The circuit performance is confirmed by both simulation and measurement results.The measurement results exhibit a peak conversion gain of 13.35 dB,a high third order input referred intercept point of 14.85 dBm,and a moderate single side band noise figure of 10.67 dB.Moreover,the whole quadrature mixer core occupies a compact die area of 0.122 mm2.It consumes a current of 3.96 mA(excluding the output buffers) under a single supply voltage of 1.8 V.     

A wide band up-conversion mixer for cable television tuner

An up-conversion mixer implemented in a 0.35μm SiGe BiCMOS technology for a double conversion cable TV tuner is described, The mixer converts the 100MHz to 1000MHz band to the Intermediate Frequency of 1GHz above. The mixer meets the linearity and noise figure requirements for a TV tuner. The noise figure （IF） of 19.2-17.5dB, ldB compression of 12.1dBm, and gain of-1-0.7dB in the 900MHz band are achieved at a supply voltage of 5V. The power consumption is 47mW.     

Millimeter-Wave Heterodyne Six-Port Receiver： New Implementation and Demodulation Results

This paper presents a new implementation of a millimeter-wave heterodyne receiver based on six-port technology.The six-port model is implemented in Advanced Design System(ADS) using S-parameter measurements for realistic advanced simulation of a short-range 60 GHz wireless link.Millimeter-wave frequency conversion is performed using a six-port down-converter.The second frequency conversion is performed using conventional means because of low IF.A comparison between the proposed receiver and a conventional balanced millimeter-wave mixer shows that the proposed receiver improves conversion loss and I/Q phase stability over the local oscillator(LO) and RF power ranges.The results of demodulating a V-band quadrature phase-shift keying(QPSK) signal at a high data rate of 100 Mb/s-1 Gb/s are discussed.The results of a bit error rate(BER) and error vector magnitude(EVM) analysis prove that the proposed architecture can be successfully used for wireless link transmission up to 10 m.     

Design and analysis of an energy-efficient O-QPSK coherent IR-UWB transceiver with a 0.52° RMS phase-noise fractional synthesizer

This paper explores an energy-efficient pulsed ultra-wideband (UWB) radio-frequency (RF) front-end chip fabricated in 0.18-μm CMOS technology,including a transmitter,receiver,and fractional synthesizer.The transmitter adopts a digital offset quadrature phase-shift keying (O-QPSK) modulator and passive direct-phase multiplexing technology,which are energy-and hardware-efficient,to enhance the data rate for a given spectrum.A passive mixer and a capacitor cross-coupled (CCC) source-follower driving amplifier (DA) are also designed for the transmitter to further reduce the low power consumption.For the receiver,a power-aware low-noise amplifier (LNA) and a quadrature mixer are applied.The LNA adopts a CCC boost common-gate amplifier as the input stage,and its current is reused for the second stage to save power.The mixer uses a shared amplification stage for the following passive IQ mixer.Phase noise suppression of the phase-locked loop (PLL) is achieved by utilizing an even-harmonics-nulled series-coupled quadrature oscillator (QVCO) and an in-band noise-aware charge pump (CP) design.The transceiver achieves a measured data rate of 0.8 Gbps with power consumption of 16 mW and 31.5 mW for the transmitter and the receiver,respectively.The optimized integrated phase noise of the PLL is 0.52° at 4.025 GHz.     

A multi-mode multi-band RF receiver front-end for a TD-SCDMA/LTE/LTE-advanced in 0.18-μm CMOS process

正A fully integrated multi-mode multi-band directed-conversion radio frequency(RF) receiver front-end for a TD-SCDMA/LTE/LTE-advanced is presented.The front-end employs direct-conversion design,and consists of two differential tunable low noise amplifiers(LNA),a quadrature mixer,and two intermediate frequency(IF) amplifiers.The two independent tunable LNAs are used to cover all the four frequency bands,achieving sufficient low noise and high gain performance with low power consumption.Switched capacitor arrays perform a resonant frequency point calibration for the LNAs.The two LNAs are combined at the driver stage of the mixer,which employs a folded double balanced Gilbert structure,and utilizes PMOS transistors as local oscillator(LO) switches to reduce flicker noise.The front-end has three gain modes to obtain a higher dynamic range.Frequency band selection and mode of configuration is realized by an on-chip serial peripheral interface(SPI) module.The frontend is fabricated in a TSMC 0.18-μm RF CMOS process and occupies an area of 1.3 mm~2.The measured doublesideband (DSB) noise figure is below 3.5 dB and the conversion gain is over 43 dB at all of the frequency bands. The total current consumption is 31 mA from a 1.8-V supply.     

Ka波段对极鳍线混频器和检波器设计

This paper mainly discusses the analysis and design of a finline single-ended mixer and detector. In the circuit, for the purpose of eliminating high-order resonant modes and improving transition loss, metallic via holes are implemented along the mounting edge of the substrate embedded in the split-block of the WG-finline-microstrip transition. Meanwhile, a Ka band slow-wave and bandstop filter, which represents a reactive termination, is designed for the utilization of idle frequencies and operation frequencies energy. Full-wave analysis is carded out to optimize the input matching network of the mixer and the detector circuit using lumped elements to model the nonlinear diode. The exported S-matrix of the optimized circuit is used for conversion loss and voltage sensitivity analysis. The lowest measured conversion loss is 3.52 dB at 32.2 GHz; the conversion loss is flat and less than 5.68 dB in the frequency band of 29-34 GHz. The highest measured zero-bias voltage sensitivity is 1450 mV/mW at 38.6 GHz, and the sensitivity is better than 1000 mV/mW in the frequency band of 38-40 GHz.     

应用于2.4GHz无线传感网的超低功耗射频接收前端设计

This paper presents the design of an ultralow power receiver front-end designed for a wireless sensor network （WSN） in a 0.18 μm CMOS process. The author designs two front-ends working in the saturation region and the subthreshold region respectively. The front-ends contain a two-stage cross-coupling cascaded common-gate （CG） LNA and a quadrature Gilbert IQ mixer. The measured conversion gain is variable with high gain at 24 dB and low gain at 7 dB for the saturation one, and high gain at 22 dB and low gain at 5 dB for the subthreshold one. The noise figure （NF） at high gain mode is 5.1 dB and 6.3 dB for each. The input 1 dB compression point （IPldB） at low gain mode is about -6 dBm and -3 dBm for each. The front-ends consume about 2.1 mA current from 1.8 V power supply for the saturation one and 1.3 mA current for the subthreshold one. The measured results show that, comparing with the power consumption saving, it is worth making sacrifices on the performance for using the subthreshold technology.     

An ultra-broadband distributed passive gate-pumped mixer in 0.18μm CMOS

A broadband distributed passive gate-pumped mixer(DPGM) using standard 0.18μm CMOS technology is presented.By employing distributed topology,the mixer can operate at a wide frequency range.In addition,a fourth-order low pass filter is applied to improve the port-to-port isolation.This paper also analyzes the impedance match and conversion loss of the mixer,which consumes zero dc power and exhibits a measured conversion loss of 9.4—17 dB from 3 to 40 GHz with a compact size of 0.78 mm~2.The input referred 1 dB compression point is higher than 4 dBm at a fixed IF frequency of 500 MHz and RF frequency of 23 GHz,and the measured RF-to-LO, RF-to-IF and LO-to-IF isolations are better than 21,38 and 45 dB,respectively.The mixer is suitable for WLAN, UWB,Wi-Max,automotive radar systems and other millimeter-wave radio applications.     

Software Radio——Software Radio： A Review of Design Considerations and Digital Hardware Choices

This paper reviews the requirements for Software Defined Radio （SDR） systems for high-speed wireless applications and compares how well the different technology choices available- from ASICs, FPGAs to digital signal processors （DSPs） and general purpose processors （GPPs） - meet them.     

EEFA： Energy Efficiency Frame Aggregation Scheduling Algorithm for IEEE 802.11n Wireless Network

Packet size is restricted due to the error-prone wireless channel which drops the network energy utilization. Furthermore, the frequent packet retransmissions also lead to energy waste. In order to improve the energy efficiency of wireless networks and save the energy of wireless devices, EEFA （Energy Efficiency Frame Aggregation）, a frame aggregation based energy-efficient scheduling algorithm for IEEE 802.11n wireless network, is proposed. EEFA changes the size of aggregated frame dynamically according to the frame error rate, so as to ensure the data transmission and retransmissions completed during the TXOP and reduce energy consumption of channel contention. NS2 simulation results show that EEFA algorithm achieves better performance than the original frame-aggregation algorithm.     

SDN-Based Data Offioading for 5G Mobile Networks

The rapid growth of 3G/4G enabled devices such as smartphones and tablets in large numbers has created increased demand formobile data services.Wi-Fi offloading helps satisfy the requirements of data-rich applications and terminals with improved multi-media.Wi-Fi is an essential approach to alleviating mobile data traffic load on a cellular network because it provides extra capaci-ty and improves overall performance.In this paper,we propose an integrated LTE/Wi-Fi architecture with software-defined net-working(SDN)abstraction in mobile backhaul and enhanced components that facilitate the move towards next-generation 5G mo-bile networks.Our proposed architecture enables programmable offloading policies that take into account real-time network condi-tions as well as the status of devices and applications.This mechanism improves overall network performance by deriving real-time policies and steering traffic between cellular and Wi-Fi networks more efficiently.     

应力和电阻率可控的适用于高品质因子MEMS器件的原位掺硼LPCVD多晶硅薄膜

The simultaneous control of residual stress and resistivity of polysilicon thin films by adjusting the deposition parameters and annealing conditions is studied. In situ boron doped polysilicon thin films deposited at 520 ℃ by low pressure chemical vapor deposition （LPCVD） are amorphous with relatively large compressive residual stress and high resistivity. Annealing the amorphous films in a temperature range of 600-800 ℃ gives polysilicon films nearly zero-stress and relatively low resistivity. The low residual stress and low resistivity make the polysilicon films attractive for potential applications in micro-electro-mechanical-systems （MEMS） devices, especially in high resonance frequency （high-f） and high quality factor （high-Q） MEMS resonators. In addition, polysilicon thin films deposited at 570 ℃ and those without the post annealing process have low resistivities of 2-5 mΩ·cm. These reported approaches avoid the high temperature annealing process （〉 1000 ℃）, and the promising properties of these films make them suitable for high-Q and high-f MEMS devices.     

A low power 3-5 GHz CMOS UWB receiver front-end

A novel low power RF receiver front-end for 3-5 GHz UWB is presented. Designed in the 0.13μm CMOS process, the direct conversion receiver features a wideband balun-coupled noise cancelling transconductance input stage, followed by quadrature passive mixers and transimpedance loading amplifiers. Measurement results show that the receiver achieves an input return loss below -8.5 dB across the 3.1-4.7 GHz frequency range, maximum voltage conversion gain of 27 dB, minimum noise figure of 4 dB, IIP3 of -11.5 dBm, and IIP2 of 33 dBm. Working under 1.2 V supply voltage, the receiver consumes total current of 18 mA including 10 mA by on-chip quadrature LO signal generation and buffer circuits. The chip area with pads is 1.1 × 1.5 mm^2.     

适用于双金属栅集成的TaN湿法腐蚀

Wet-etch etchants and the TaN film method for dual-metal-gate integration are investigated. Both HF/HN O3/H2O and NH4OH/H2O2 solutions can etch TaN effectively, but poor selectivity to the gate dielectric for the HF/HNO3/H2O solution due to HF being included in HF/HNO3/H2O, and the fact that TaN is difficult to etch in the NH4OH/H2O2 solution at the first stage due to the thin TaOxNy layer on the TaN surface, mean that they are difficult to individually apply to dual-metal-gate integration. A two-step wet etching strategy using the HF/HNO3/H2O solution first and the NH4OH/H2O2 solution later can fully remove thin TaN film with a photo-resist mask and has high selectivity to the HfSiON dielectric film underneath. High-k dielectric film surfaces are smooth after wet etching of the TaN metal gate and MOSCAPs show well-behaved C-V and Jg-Vg characteristics, which all prove that the wet etching of TaN has little impact on electrical performance and can be applied to dual-metal-gate integration technology for removing the first TaN metal gate in the PMOS region.     

基于非线性DAC的高速直接数字频率合成器

This paper presents a high speed ROM-less direct digital frequency synthesizer （DDFS） which has a phase resolution of 32 bits and a magnitude resolution of 10 bits. A 10-bit nonlinear segmented DAC is used in place of the ROM look-up table for phase-to-sine amplitude conversion and the linear DAC in a conventional DDFS. The design procedure for implementing the nonlinear DAC is presented. To ensure high speed, current mode logic （CML） is used. The chip is implemented in Chartered 0.35μm COMS technology with active area of 2.0 × 2.5 mm^2 and total power consumption of 400 mW at a single 3.3 V supply voltage. The maximum operating frequency is 850 MHz at room temperature and 1.0 GHz at 0℃.     

一种应用于频率综合器的全差分电荷泵的设计与噪声分析

A fully-differential charge pump（FDCP）with perfect current matching and low output current noise is realized for phase-locked loops（PLLs）.An easily stable common-mode feedback（CMFB）circuit which can handle high input voltage swing is proposed.Current mismatch and current noise contribution from the CMFB circuit is minimized.In order to optimize PLL phase noise,the output current noise of the FDCP is analyzed in detail and calculated with the sampling principle.The calculation result agrees well with the simulation.Based on the noise analysis,many methods to lower output current noise of the FDCP are discussed.The fully-differential charge pump is integrated into a 1–2 GHz frequency synthesizer and fabricated in an SMIC CMOS 0.18μm process.The measured output reference spur is–64 dBc to–69 dBc.The in-band and out-band phase noise is–95 dBc/Hz at 3 kHz frequency offset and–123 dBc/Hz at 1 MHz frequency offset respectively.     

Software-Defined Cellular Mobile Network Solutions

The emergency relating to software-defined networking(SDN),especially in terms of the prototype associated with OpenFlow,pro-vides new possibilities for innovating on network design.Researchers have started to extend SDN to cellular networks.Such newprogrammable architecture is beneficial to the evolution of mobile networks and allows operators to provide better services.Thetypical cellular network comprises radio access network(RAN)and core network(CN);hence,the technique roadmap diverges intwo ways.In this paper,we investigate SoftRAN,the latest SDN solution for RAN,and SoftCell and MobileFlow,the latest solu-tions for CN.We also define a series of control functions for CROWD.Unlike in the other literature,we emphasize only software-defined cellular network solutions and specifications in order to provide possible research directions.     

基于代数签名且支持数据动态更新的云数据完整性验证方案(英文)

Cloud storage is one of the main application of the cloud computing. With the data services in the cloud, users is able to outsource their data to the cloud, access and share their outsourced data from the cloud server anywhere and anytime. However, this new paradigm of data outsourcing services also introduces new security challenges, among which is how to ensure the integrity of the outsourced data. Although the cloud storage providers commit a reliable and secure environment to users, the integrity of data can still be damaged owing to the carelessness of humans and failures of hardwares/softwares or the attacks from external adversaries. Therefore, it is of great importance for users to audit the integrity of their data outsourced to the cloud. In this paper, we first design an auditing framework for cloud storage and proposed an algebraic signature based remote data possession checking protocol, which allows a third-party to auditing the integrity of the outsourced data on behalf of the users and supports unlimited number of verifications. Then we extends our auditing protocol to support data dynamic operations, including data update, data insertion and data deletion. The analysis and experiment results demonstrate that our proposed schemes are secure and efficient.