纳米石墨晶薄膜的场发射特性

研究了纳米石墨晶的场发射特性，介绍了纳米石墨晶薄膜的制备方法，通过扫描电镜和Raman光谱对纳米石墨晶的结构进行了分析，场发射特性测试表明纳米石墨晶薄膜的场发射阈值电场为1.8V/μm。根据实验结果计算出纳米石墨晶的有效功函数在0.75-1.62eV之间，研究表明纳米石墨晶薄膜具有一些独到的特点，也非常适合场发射显示用冷阴极的制备。     

硅纳米线纳米器件的研究进展

硅纳米线作为一类重要的一维半导体纳米材料,在纳米器件方面具有很好的应用前景,可以用于高性能场效应晶体管、单电子探测器和场发射显示器件等纳米器件的制备.介绍了近两年来硅纳米线作为检测细胞、葡萄糖、过氧化氢、牛类血清蛋白和DNA杂交方面的纳米传感器、纳米晶体管、光电探测器等纳米器件的最新进展,并对其研究前景做了展望.     

外延纳米金刚石膜及其场发射特性

研究了纳米金刚石外延薄膜的制备方法及其场发射特性。采用电泳方法将粒径20nm以下的纳米金刚石微品沉积到Ti电极衬底上，用热丝CVD方法在纳米金刚石微晶薄膜上再外延生长一层含非晶碳金刚石薄膜。用Raman光谱研究了外延纳米金刚石薄膜的结构并在高真空条件下研究了其场发射特性。     

电泳工艺制备阵列场发射阴极及其性能的研究

碳纳米管是理想的场发射冷阴极材料,阴极的图形阵列化是实现碳纳米管场发射显示器动态全彩视频显示的核心.三极管结构能够更好地进行矩阵寻址显示图像,且与常规的驱动电路相兼容,降低整体平板显示器件的制作成本.从实验出发,探索利用简单的电泳工艺制备图形化碳基薄膜阴极,采用与阴极成同一水平面的栅极的三极管结构,并对电泳的实验参数进行优化以提高阴极电压电流特性和发射的均匀性等问题,为场发射器件的制造提供优良的工艺基础.研究机械球磨和稀释悬浊液浓度对碳纳米管沉积均匀性的影响.实验结果表明稀薄的悬浊液的条件下可以在玻璃的银浆导电层上沉积较薄而均匀的碳纳米管膜,与丝网印刷工艺制备的阴极相比,均匀性更好,厚度更容易控制,具有更好的发射均匀性.测试图形化的阵列碳纳米阴极的三极管结构的场发射特性,发现当阳极电压保持在600 V,栅极电压接近500 V时,阳极电流能达到2.6 mA/cm2.荧光粉发光均匀,相比二极管结构具有更低的阈值电压,在亮度、均匀性和稳定性方面都有显著的优势.     

场致发射显示技术研究进展

首先回顾了Spindt型微场发射技术，介绍了场发射显示技术的发展过程、器件结构和工作原理，讨论了目前这项技术所面临的问题，着重介绍了近两年来在场发射显示技术研究领域的最新进展，包括纳米碳管和复合材料在FED中应用前景。     

碳纳米球薄膜的场发射特性

利用微波等离子体化学气相沉积法,在Si(100)衬底上制备了碳纳米球薄膜。利用拉曼光谱和场发射扫描电子显微镜研究了薄膜的结构以及表面形貌,表明碳纳米球薄膜是由约2～3μm长、100nm宽的无定形碳纳米片相互缠绕、交织成球状而构成的。在高真空系统中测量了碳纳米球薄膜的场发射特性,结果表明,碳纳米球薄膜具有良好的场发射特性,阈值电场为3.1V/μm,当电场增加到10V/μm时,薄膜的场发射电流密度可达到60.7mA/cm2。通过三区域电场模型合理地解释了碳纳米球薄膜在低电场、中间电场和高电场区域的场发射特性。     

碳纳米管(CNT)场发射显示器的关键技术的研究

对碳纳米管阴极的制备以及场发射显示器的真空封装技术进行了研究.利用一种新的碳纳米管生长工艺制备出了具有优良场发射性能的碳纳米管阴极.并将这种直接生长的碳纳米管薄膜作为阴极,结合一种弹性封装工艺,开发了一种具有简单字符显示功能的场发射显示器.该显示器在较低的工作电压下就可获得高亮度的显示效果,并且器件的亮度与驱动电压成较好的线性关系,这将有利于未来的碳纳米管场发射显示器实现高亮度和多级灰度显示.器件的持续工作寿命测试已经超过5500小时,充分验证了碳纳米管作为场发射阴极的应用潜力.     

纳米碳材料场发射特性研究进展

碳纳米结构材料如纳米碳管、纳米金刚石、纳米碳纤维都具有良好的场电子发射性能,它们低的发射阈值和高发射电流密度极具应用潜力。该文对这几种碳纳米结构材料的场发射特性的研究进展进行了评述,着重讨论了影响场发射材料的性能指标,并讨论了研究中存在的问题。     

热CVD法制备的碳纳米管线阵列的场发射特性

采用半导体光刻技术在硅衬底上获得图形化掩膜,然后用热化学气相淀积(T-CVD)的方法制备了图形化的碳纳米管线阵列,用扫描电镜和拉曼光谱仪对碳纳米管进行了表征.研究了图形化碳纳米管线阵列的场发射特性,并与无图形化处理的碳纳米管薄膜样品的场发射特性进行了比较.当发射电流密度达到10 μA/cm2时,无图形化处理的碳纳米管薄膜、10 μm碳纳米管线阵列以及2 μm碳纳米管线阵列样品的开启电场分别为3 V/μm、2.1 V/μm和1.7 V/μm;而当电场强度达3.67 V/μm时,相应的电流密度分别为2.57 mA/cm2、4.65 mA/cm2和7.87 mA/cm2. 实验结果表明,图形化处理后的碳纳米管作为场发射体,其场发射特性得到了明显的改善.对改善的原因进行了分析和讨论.     

平面型纳米真空三极管的计算机模拟

平面纳米真空三极管只需要平面工艺,与现有的微电子工艺兼容,与基于经典Spindt阴极的真空微电子三极管相比,具有工艺相对简单等特点,同样具备纳米真空电子器件抗辐射、温度稳定性好等优点。本文采用粒子模拟方法对平面型纳米真空三极管的场发射特性进行了计算机模拟研究,模拟中考虑了空间电荷的影响。典型器件的模拟结果表明,平面型纳米真空三极管具有信号响应速度快,工作电压较低等优点。研究了该三极管结构中的尖端曲率半径、尖端相对高度、栅极电压和阳极电压对场发射特性的影响,有助于设计和优化该类器件结构。这种平面型纳米真空三极管可望成为真空集成电路的基础器件,并在卫星等航空航天领域等需要抗辐射领域获得应用。     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Development of the readout system for waveguide multilayer optical card

Waveguide multilayer optical card （WMOC） is a novel storage device of three-dimensional optical information. An advanced readout system fitting for the WMOC is introduced in this paper. The hardware mainly consists of the light source for reading, WMOC, motorized stages addressing unit, microscope imaging unit, CCD detecting unit and PC controlling ＆ processing unit. The movement of the precision motorized stage is controlled by the computer through Visual Basic （VB） language in software. A control panel is also designed to get the layer address and the page address through which the position of the motorized stages can be changed. The WMOC readout system is easy to manage and the readout result is directly displayed on computer monitor.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

Collinear phase-matching study of terahertz-wave generation via difference frequency mixed in GaAs and Inp

The collinearly phase-matching condition of terahertz-wave generation via difference frequency mixed in GaAs and InP is theoretically studied. In collinear phase-matching, the optimum phase-matching wave hands of these two crystals are calculated. The optimum phase-matching wave bands in GaAs and lnP are 0.95-1.38μm and 0.7-0.96μm respectively. The influence of the wavelength choice of the pump wave on the coherent length in THz-wave tuning is also discussed. The influence of the temperature alteration on the phase-matching and the temperature tuning properties in GaAs crystal are calculated and analyzed. It can serve for the following experiments as a theoretical evidence and a reference as well.     

Effects of the alloy compositions on the phonon-polaritons in ternary mixed crystals

Composition dependence of bulk and surface phonon-polaritons in ternary mixed crystals are studied in the framework of the modified random-element-isodisplacement model and the Bom-Huang approximation. The numerical results for Several Ⅱ - Ⅵ and Ⅲ- Ⅴ compound systems are performed, and the polariton frequencies as functions of the compositions for ternary mixed crystals AlxGa1-xAs, GaPxAS1-x, ZnSxSe1-x, GaAsxSb1-x, GaxIn1-xP, and ZnxCd1-xS as examples are given and discussed. The results show that the dependence of the energies of two branches of bulk phonon-polaritons which have phonon-like characteristics, and surface phonon-polaritons on the compositions of ternary mixed crystals are nonlinear and different from those of the corresponding binary systems.     

New insert layer structure OLEDs

An insert layer structure organic electroluminescent device（OLED） based on a new luminescent material （Zn（salen）） is fabricated. The configuration of the device is ITO/CuPc/NPD/Zn（salen）/Liq/LiF/A1/CuPc/NPD/Zn（salen）/Liq/LiF/A1. Effective insert electrode layers comprising LiF（1nm）/Al（5 nm） are used as a single semitransparent mirror, and bilayer cathode LiF（1 nm）/A1（100 nm） is used as a reflecting mirror. The two mirrors form a Fabry-Perot microcavity and two emissive units. The maximum brightness and luminous efficiency reach 674 cd/m^2 and 2.652 cd/A, respectively, which are 2.1 and 3.7 times higher than the conventional device, respectively. The superior brightness and luminous efficiency over conventional single-unit devices are attributed to microcavity effect.