共查询到20条相似文献,搜索用时 78 毫秒
1.
利用脉冲激光沉积法(PLD)制备了Ga掺杂的Zn0.9Mg0.1O(ZMOGa)宽带隙透明导电薄膜.采用各种分析手段研究了沉积温度和真空退火处理对薄膜结构、表面形貌及光电性能的影响.结果表明,制备的薄膜具有ZnO(002)择优取向;200℃下沉积的薄膜通过3×10-3Pa的真空400℃退火2h后,其电阻率由8.12×10-4Ω·cm减小到4.74×10-4Ω·cm,禁带宽度则由原来的3.83eV增加到3.90eV.退火处理增强了薄膜的择优取向和结晶度、增加了禁带宽度、提高了载流子浓度并使其透射谱线的光学吸收边发生蓝移现象. 相似文献
2.
用光电流作用谱、光电流-电势图等光电化学方法研究了ITO/聚3-甲基噻吩(PMeT)膜电极和ITO/TiO2/PMET复合膜电极的光电转换性质.结果表明,PMET膜导带位置为-3.44eV,禁带宽度为1.93eV.修饰ITO/TiO2电极可使光电流发生明显的红移,从而提高了宽禁带半导体的光电转换效率. 相似文献
3.
以硅烷 (SiH4 )和硼烷 (B2 H6)为气相反应先驱体 ,采用等离子体增强化学气相沉积法 (PECVD)制备出轻掺硼非晶氢硅薄膜。X射线衍射、原子力显微镜和光、暗电导测试表明 ,一定程度的硼掺杂提高了非晶氢硅薄膜的电导率 ,降低了非晶氢硅薄膜的光、暗电导比 ,并促进了非晶氢硅薄膜中硅微晶粒的生长。红外吸收谱研究预示了大量的硼原子与硅、氢原子之间能形成某些形式的复合体 ,仅有少量硼元素对P型掺杂有贡献。 相似文献
4.
研究了电子束法沉积ZnIn_2Se_4薄膜的工艺条件,所得致密、均匀膜的导电类型可以通过不同气氛处理得到控制。该膜的最佳参数为:电阻率ρ为2.35×10~(-1)Ω·cm,Hall迁移率μ_H为106cm~2·V~(-1)·S~(-1),载流子浓度N是1.51×10~(17)cm~(-3),禁带宽度E_(?)为2.23eV。采用XPS技术研究了膜的组成、结构、价态。 相似文献
5.
掺硼非晶硅薄膜的微结构和电学性能研究 总被引:3,自引:0,他引:3
以硅烷(SiH4)和硼烷(B2H6)为气相反应先驱体,采用等离子体增强化学气相沉积法,(PECVD)制备出能应用于液晶光阀光导层的硼掺杂非晶氢硅薄膜。X射线衍射、原子力显微镜和光、暗电导测试表明,一定程度的硼掺杂提高了非晶氢硅薄膜的电导率、降低了非晶氢硅薄膜的光、暗电导比;硼掺杂促进薄膜晶态率的增加和硅晶粒尺寸的增大,薄膜的结晶状态将逐渐从非晶硅过渡到纳米硅,最后发展为多晶硅。红外吸收谱研究表明了大量的硼原子与硅、氢原子之间能形成某些形式的复合体,仅有少量硼元素对受主掺杂有贡献。 相似文献
6.
我们用热丝辅助MW ECRCVD系统,在热丝温度分别为0、1350、1400、1450、1500、1600和1700℃时制备出a-SiH薄膜.通过膜厚测定,红外光谱分析光、暗电导测量等手段,分析了其沉积速率、光敏性及光学带隙的变化规律.结果表明沉积速率和薄膜质量均得到明显的提高,沉积速率超过3nm/s,光暗电导之比提高到6×105.找到最佳辅助热丝温度为1450℃.通过对带隙值的分析,发现当带隙值在1.6~1.7范围内时,薄膜几乎都具有105以上的光暗电导之比. 相似文献
7.
硼掺杂对非晶硅薄膜微结构和光电性能的影响 总被引:2,自引:0,他引:2
以硅烷(SiH4)和硼烷(B2H6)为气相应反应先驱体,采用等离子体增强化学气相沉积法(PECVD)制备出轻掺硼非昌氢硅薄膜,X射线衍射,原子力显微镜和光,暗电导测试表明,一定程度的硼掺杂提高了非晶氢硅薄膜的电导率,降低了非晶氢硅薄膜的光,暗电导比,并促进了非晶氢硅薄膜中硅微晶粒的生长,红外吸为研究预示了大量的硼原子与硅,氢原子之间能形成某些形式的复合体,仅有少量硼元素对P型掺杂有贡献。 相似文献
8.
利用常规的层状结构的空间电荷限制电流法,测得了具有一定厚度 d 的 GD-a-Si_(1-x)C_x∶H 和 GD-a-Si_(1-x)N_x∶H 膜不同含量 x 时的隙态分布 N(E):对 GD-a-Si_(1-x)C_x∶H 膜(d(?)1μm),当 x 为0、0.1、0.8时,平衡费米能级附近处的隙态密度 N(E_(?)~o)分别为2×10~(15)、4×10~(15)、6.2×10~(16)/cm~3·eV,对 GD-a-Si_(1-x)N_x∶H 膜(d(?)1μm),当 x 为0、0.05、0.2时,N(E_F~o)分别为2×10~(15)、3×10~(15)、4.5×10~(16)/cm~3·eV;得到了 GD-a-Si∶H 膜的隙态分布与膜厚度的关系,发现随着膜厚度的增加 N(E_F~o)在减小,当 d<1μm 时,N(E_F~o)约为10~(16)/cm~3·eV 的数量级,当 d>1μm 时,N(E_F~o)约为10~(15)/cm~3·eV 的数量级。对共面电极结构的样品,用温度调制空间电荷限制电流法(TM-SCLC),测得了 GD-a-Si∶H 膜的隙态分布,并对光处理前后的样品进行比较,发现强光照后存在有光诱导效应。我们对所得结果作了初步说明。 相似文献
9.
10.
聚3-己基噻吩的光电性能研究 总被引:4,自引:0,他引:4
利用光电化学方法研究了聚3-己基噻吩的光电化学性质,其禁带宽度为1.89eV,同时确定了它的价带位置(-3.6eV)、导带位置(-5.4eV).研究发现聚3-己基噻吩属于直接跃迁型半导体,在本文条件下得到的最高IPCE值达5.2% 相似文献
11.
《International journal for numerical methods in engineering》2018,113(9):1488-1506
In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method. 相似文献
12.
Standards are the basis for production enterprises to organize production ex-factory inspection trade 《中国标准化(英文版)》2008,25(1):24-25
Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.…… 相似文献
13.
14.
A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa. 相似文献
15.
Steffen Müller-Probandt 《材料科学与工程:中英文B版...》2018,(4):161-177
We associate a variety of innovations with the term "Industry 4.0". The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di... 相似文献
16.
On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.…… 相似文献
17.
Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß. 相似文献
18.
Janet Lang 《Materials and Manufacturing Processes》2017,32(7-8):857-866
ABSTRACTThe production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them. 相似文献
19.
C. Qihong W. Zhan‐Wen J. Yi J. Yehua L. Fei F. Hanguang 《Materialwissenschaft und Werkstofftechnik》2014,45(7):582-590
In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M2(B,C), (W,Mo)2(B,C), M3(B,C), M23(B,C)6 type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm2. The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K1 mill housing of bar mill. 相似文献
20.
《中国标准化(英文版)》2014,(4)
正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from 相似文献