Visible light induced photocatalytic reduction of Cr(VI) over polymer-sensitized TiO2 and its synergism with phenol oxidation

In this study, both Cr(VI) reduction and phenol oxidation induced by polymer-sensitized TiO₂ were investigated under visible light. Study of the reaction mechanism indicated that poly(fluorene-co-thiophene) (PFT) acted as a semiconductor and was by itself able to reduce Cr(VI) under visible light irradiation. When coupled with TiO₂, PFT served not only as the electron donor for Cr(VI) reduction, but also as a sensitizer. Upon irradiation by visible light, electrons in the sensitizing PFT polymer are excited and are transferred to the conduction band of TiO₂. PFT-catalyzed reduction of Cr(VI) was significantly promoted by the presence of phenol, and synergism between Cr(VI) reduction and phenol degradation was demonstrated both by analysis of the FT-IR spectrum of PFT/TiO₂ and by measuring the effect of repeated use of PFT/TiO₂ on its photocatalytic efficiency. The results provide a cost-effective method to remove organic and inorganic pollutants simultaneously in the complex wastewater.     

Preliminary trial on degradation of waste activated sludge and simultaneous hydrogen production in a newly-developed solar photocatalytic reactor with AgX/TiO2-coated glass tubes

A solar fluidized tubular photocatalytic reactor (SFTPR) with simple and efficient light collector was developed to degrade waste activated sludge (WAS) and simultaneously produce hydrogen. The photocatalyst was a TiO₂ film doped by silver and silver compounds (AgX). The synthesized photocatalyst, AgX/TiO₂, exhibited higher photocatalytic activity than TiO₂ (99.5% and 30.6% of methyl orange removal, respectively). The installation of light collector could increase light intensity by 26%. For WAS treatment using the SFTPR, 69.1% of chemical oxygen demand (COD) removal and 7866.7 μmol H₂/l-sludge of hydrogen production were achieved after solar photocatalysis for 72 h. The SFTPR could be a promising photocatalysis reactor to effectively degrade WAS with simultaneous hydrogen production. The results can also provide a useful base and reference for the application of photocatalysis on WAS degradation in practice.     

A comparison of several nanoscale photocatalysts in the degradation of a common pollutant using LEDs and conventional UV light

A comparative study on the photocatalytic activities of four different catalysts, P-25 TiO₂, TiO₂ nanofibers, tin-doped TiO₂ nanofibers under UV light irradiation at 350 nm, and coumarin (C-343) coated TiO₂ nanofibers at 436 nm light emitting diodes (LED) is reported. Catalysts performance has been compared based on their reflectance spectrum and activity. A common water contaminant 4-chlorophenol was used as a substrate to compare the activity of the different catalysts under both direct and dye sensitized conditions. Results indicated that amongst the four different catalysts the activity of P-25 was the highest. However the activity of C-343 coated TiO₂ nanofibers in the LED (436 nm) based reactor was competitive. Identification of reaction intermediates implied that the reaction pathways under UV (band gap) and visible (dye sensitized) irradiation were different. Nonetheless, ring opening took place in all reactions with both maleic and dihydroxymaleic have been identified as intermediates. The study indicates that ordered arrays of TiO₂ irradiated by panels of arrays of low cost high intensity LEDs might be used for the design of reactors. The near monochromaticity, long life, and operation under direct currents are advantages of using LEDs.     

Concurrent filtration and solar photocatalytic disinfection/degradation using high-performance Ag/TiO2 nanofiber membrane

A facile polyol synthesis was used for the deposition of Ag nanoparticles on electrospun TiO₂ nanofibers for the subsequent fabrication of Ag/TiO₂ nanofiber membrane. The permeate flux of the Ag/TiO₂ nanofiber membrane was remarkably high compared to commercial P25 deposited membrane. The Ag/TiO₂ nanofiber membrane achieved 99.9% bacteria inactivation and 80.0% dye degradation under solar irradiation within 30 min. The Ag/TiO₂ nanofiber membrane also showed excellent antibacterial capability without solar irradiation. Considering the excellent intrinsic antibacterial activity and high-performance photocatalytic disinfection/degradation under solar irradiation, this novel membrane proved to have promising applications in water purification industry.     

Coupling membrane separation and photocatalytic oxidation processes for the degradation of pharmaceutical pollutants

The coupling of membrane separation and photocatalytic oxidation has been studied for the removal of pharmaceutical pollutants. The retention properties of two different membranes (nanofiltration and reverse osmosis) were assessed. Comparable selectivity on the separation of pharmaceuticals were observed for both membranes, obtaining a permeate stream with concentrations of each pharmaceutical below 0.5 mg L⁻¹ and a rejected flux highly concentrated (in the range of 16–25 mg L⁻¹ and 18–32 mg L⁻¹ of each pharmaceutical for NF-90 and BW-30 membranes, respectively), when an initial stream of six pharmaceuticals was feeding to the membrane system (10 mg L⁻¹ of each pharmaceutical). The abatement of concentrated pharmaceuticals of the rejected stream was evaluated by means of heterogeneous photocatalytic oxidation using TiO₂ and Fe₂O₃/SBA-15 in presence of hydrogen peroxide as photo-Fenton system. Both photocatalytic treatments showed remarkable removals of pharmaceutical compounds, achieving values between 80 and 100%. The nicotine was the most refractory pollutant of all the studied pharmaceuticals. Photo-Fenton treatment seems to be more effective than TiO₂ photocatalysis, as high mineralization degree and increased nicotine removal were attested. This work can be considered an interesting approach of coupling membrane separation and heterogeneous photocatalytic technologies for the successful abatement of pharmaceutical compounds in effluents of wastewater treatment plants.     

Visible-light-induced photocatalysis of low-level methyl-tertiary butyl ether (MTBE) and trichloroethylene (TCE) using element-doped titanium dioxide

While the photocatalytic degradation of various volatile organic compounds in conjunction with UV light has been widely reported, visible-light-induced photocatalytic degradation of low-levels of the pollutants MTBE and TCE, which have been linked to potential adverse health effects, is rarely reported. The present study examined whether visible-light-activated S- or N-doped TiO₂ photocatalytic technology can be used to control indoor concentrations of MTBE and TCE. This study consists of the characterization of the doped TiO₂ powders, as well as an investigation of their photocatalytic activities. In regards to both powders, a shift of the absorbance spectrum towards the visible light region was observed. An activity test suggested that these photocatalysts exhibited reasonably high degradation efficiencies towards MTBE and TCE under visible light irradiation. The degradation efficiencies of MTBE and TCE by S- and N-doped photocatalysts exceeded 75 and 80%, respectively, at input concentrations (IC) of 0.1 ppm. Degradation efficiency was dependent on both IC and relative humidity. TCE could enhance the degradation efficiency of MTBE even under visible-light irradiation. The estimated mineralization efficiencies (MEs) were comparable to those of previous studies conducted with UV/TiO₂ systems. Similar to the relative degradation efficiencies, the ME of TCE was higher in comparison to that of MTBE. The CO production measured during the photocatalytic processes represented a negligible addition to indoor CO levels. These results suggest that visible-light-activated S- and N-doped TiO₂ photocatalysts may prove a useful tool in the effort to improve indoor air quality.     

Bio-reduction of soluble chromate using a hydrogen-based membrane biofilm reactor

Hexavalent chromium (Cr(VI)) is a mutagen and carcinogen that is a significant concern in water and wastewater. A simple and non-hazardous means to remove Cr(VI) is bioreduction to Cr(III), which should precipitate as Cr(OH)3(s). Since Cr(VI)-reducing bacteria can use hydrogen (H2) as an electron donor, we tested the potential of the H2-based membrane biofilm reactor (MBfR) for chromate reduction and removal from water and wastewater. When Cr(VI) was added to a denitrifying MBfR, Cr(VI) reduction was immediate and increased over 11 days. Short-term experiments investigated the effects of Cr(VI) loading, H2 pressure, and nitrate loading on Cr(VI) reduction. Increasing the H2 pressure improved Cr(VI) reduction. Cr(VI) reduction also was sensitive to pH, with an optimum near 7.0, a sharp drop off below 7.0, and a gradual decline to 8.2. Cr(III) precipitated after a small upward adjustment of the pH. These experiments confirm that a denitrifying, H2-based MBfR can be used to reduce Cr(VI) to Cr(III) and remove Cr from water. The research shows that critical operational parameters include the H2 concentration, nitrate concentration, and pH.     

Effects of water parameters on the degradation of microcystin-LR under visible light-activated TiO2 photocatalyst

A study was performed to determine the effect of pH, alkalinity, natural organic matter (NOM) and dissolved oxygen in the performance of nitrogen and fluorine doped TiO₂ (NF-TiO₂) for the degradation of hepatotoxin microcystin-LR (MC-LR) in synthetic and natural water under visible light irradiation. The initial degradation rate of MC-LR was fastest under acidic conditions (3.50 ± 0.02 × 10⁻³ μM min⁻¹ at pH 3.0) and decreased to 2.29 ± 0.07 × 10⁻³ and 0.54 ± 0.02 × 10⁻³ μM min⁻¹ at pH 5.7 and 7.1, respectively. Attractive forces between the opposite charged MC-LR and NF-TiO₂ are likely responsible for the enhancement in the photocatalytic decomposition of MC-LR resulting from increased interfacial adsorption. For carbonate buffered solutions, the photocatalytic activity of NF-TiO₂ was reduced when increasing the carbonate concentration up to 150 mg CaCO₃ L⁻¹. The scavenging of radical species by the bicarbonate ion at pH 7.1 is discussed. In the presence of NOM, the degradation rates decreased as pH and initial concentration of the NOM increased. The inhibition was higher with fulvic acid than humic acid under alkaline conditions. Oxygenated solution yields higher NF-TiO₂ photocatalytic degradation of MC-LR compared to nitrogen sparged solution at pH 5.7. The involvement of specific reactive oxygen species implicated in the photodegradation is proposed. Finally, no significant degradation is observed with various natural waters spiked with MC-LR under visible light (λ > 420 nm) but high removal was achieved with simulated solar light. This study provides a better understanding of the interactions and photocatalytic processes initiated by NF-TiO₂ under visible and solar light. The results indicate solar photocatalytic oxidation is a promising technology for the treatment of water contaminated with cyanotoxins.     

Antifungal capability of TiO2 coated film on moist wood

Photocatalytic oxidation by TiO₂ has been shown to deactivate biological pollutants. Most previous studies evaluated TiO₂'s antimicrobial performance using bacteria, with Escherichia coli most commonly applied as the test microbe. There have not been concentrated studies focusing on the photocatalytic disinfection of fungi which widely exist in buildings and cause health problems. In this study, the antifungal activity of TiO₂ photocatalytic reaction against Aspergillus niger was investigated for moist wood boards during periods of several weeks. TiO₂ coated film in the presence of UVA (365 nm) irradiation exhibited antifungal capability. No visible growth was observed on specimens during the photo-process. Re-growth appeared in subsequent dark, indicating that the photocatalytic reaction was not sufficient for total disinfection against mold fungi but did suppress fungi growth. The study sheds light on conditions and potential applications of photocatalytic deactivation of fungi.     

Electrochemical degradation of chlortetracycline using N-doped Ti/TiO2 photoanode under sunlight irradiations

The appearance and the persistence of pharmaceutical products in the aquatic environment urgently call for the development of an innovative and practical water treatment technology. This study deals with the development of nanostructured nitrogen-doped TiO₂ photoanodes and their subsequent use for chlortetracycline (CTC) photoelectrocatalytic oxidation under visible light. The N-doped TiO₂ photoanodes with different nitrogen contents were prepared by means of a radiofrequency magnetron sputtering (RF-MS) process, with the objective to tune shift their optical absorption from the UV towards the visible. The N-doped TiO₂ consist of nanostructured anatase phase with average TiO₂ nanocrystallite size of 29 nm. The nitrogen doping is clearly shown to produce the desired red shift of the absorption onset of the TiO₂ coatings (from ∼380 nm to ∼550 nm). Likewise, the N-doped TiO₂ are found to be highly photo-electroactive not only under the UV light but most interestingly under the visible light as well. Using the optimal N-doped photoanodes, 99.6% of CTC (100 μg/L) was successfully degraded after 180 min of treatment time with a current intensity of 0.6 A. Under these conditions, a relatively high mineralization of CTC (92.5% ± 0.26% of TOC removal and 90.3% ± 1.1% of TN removal) was achieved.     

Photocatalytic degradation of 2,4-dinitrophenol (DNP) by multi-walled carbon nanotubes (MWCNTs)/TiO2 composite in aqueous solution under solar irradiation

Nanosized multi-walled carbon nanotubes (MWCNTs)/TiO₂ composite and neat TiO₂ photocatalysts were synthesized by sol-gel technique using tetrabutyl titanate as a precursor. The as prepared photocatalysts were characterized using XRD, SEM, FTIR and UV-vis spectra. The samples were evaluated for their photocatalytic activity towards the degradation of 2,4-dinitrophenol (DNP) under solar irradiation. The results indicated that the addition of an appropriate amount of MWCNTs could remarkably improve the photocatalytic activity of TiO₂. An optimal MWCNTs:TiO₂ ratio of 0.05% (w/w) was found to achieve the maximum rate of DNP degradation. The effects of pH, irradiation time, catalyst concentration, DNP concentration, etc. on the photocatalytic activity were studied and the results obtained were fitted to the Langmuir-Hinshelwood model to study the degradation kinetics. The optimal conditions were an initial DNP concentration of 38.8 mg/L at pH 6.0 with catalyst concentration of 8 g/L under solar irradiation for 150 min with good recyclisation of catalyst. The degree of photocatalytic degradation of DNP increased with an increase in temperature. The MWCNTs/TiO₂ composite was found to be very effective in the decolorization and COD reduction of real wastewater from DNP manufacturing. Thus, this study showed the feasible and potential use of MWCNTs/TiO₂ composite in degradation of various toxic organic contaminants and industrial effluents.     

Membrane vis-LED photoreactor for simultaneous penicillin G degradation and TiO2 separation

The hybrid membrane photoreactor (MPR) combining a photoreactor irradiated with visible-light-emitting diode (vis-LED) and a cross-flow microfiltration (MF) membrane module was investigated in both closed-loop and continuous flow-through modes for the simultaneous degradation of penicillin G (PG) and separation of visible-light responsive TiO₂ particles, namely C-sensitized-N-doped TiO₂ (T300) and C-N-S tridoped TiO₂ (T0.05-450). The turbidity of permeate water was <0.2 NTU for both T300 and T0.05-450 suspensions in the MPR system operated at different transmembrane pressures (TMPs) and cross-flow velocities (CFVs), indicating effective separation of TiO₂ particles by the MF membrane. The operations at a higher TMP or lower CFV were more prone to induce TiO₂ deposition on the membrane surface without backwashing, which resulted in the membrane fouling, the loss of TiO₂ from the photoreactor and the decrease of PG photocatalytic degradation efficiency. 75% and 84% of PG were degraded in the closed-loop MPR without backwashing operated at 10 kPa and 0.15 m s⁻¹ after 4 h of vis-LED irradiation using 1.0 g L⁻¹ of T300 and T0.05-450, respectively. With backwashing of the membrane, the PG photocatalytic degradation efficiencies in the closed-loop MPR could be significantly enhanced to achieve 93% and 95% using 1.0 g L⁻¹ of T300 and T0.05-450, respectively, which were almost comparable to those achieved in the batch photoreactor. Due to its shorter hydraulic residence time in the photoreactor, the PG degradation efficiency in the continuous flow-through MPR with backwashing was lower than that achieved in the closed-loop MPR.     

Chromate reduction by zero-valent Al metal as catalyzed by polyoxometalate

In spite of a high reduction potential of zero-valent Al (ZVAl), its ability to reduce Cr(VI), a widespread pollutant, to less toxic Cr(III) remains to be uncovered. In the present study, Cr(VI) reduction by ZVAl was conducted to evaluate the potential application of Al as a reductant for Cr(VI). Polyoxometalate (POM, HNa₂PW₁₂O₄₀), a catalyst, was used to accelerate Cr(VI) reduction by Al. The reaction of 0.192 mM Cr(VI) on ZVAl was investigated in the presence of N₂ or O₂ at pH 1. A slight decrease in Cr(VI) concentration was observed on as-received (uncleaned) ZVAl due to the presence of oxide layer with a low surface area (ca. 3.4 × 10⁻³ m²/g) of ZVAl. On addition of 0.1 mM POM, Cr(VI) reduction on uncleaned ZVAl increased significantly. This is attributed to the unique properties of POM, which has a Brφnsted acidity higher than usual inorganic acids such as H₂SO₄ and HCl. Thus, POM could remove rapidly the oxidize layer on ZVAl, followed by acting as a shuttle for electron transfer from ZVAl to Cr(VI). Under a N₂ atmosphere, one- or two-electron reduction of POM by ZVAl was responsible for Cr(VI) reduction in the early stage of the reaction. However, during reaction with ZVAl over 120 min, three-electron reduction of POM predominated over Cr(VI) reduction. On interaction of O₂ with reduced POM, the formation of H₂O₂ was responsible for subsequent Cr(VI) reduction. The results suggest that POM is an efficient catalyst for Cr(VI) reduction by Al due to the extremely rapid consumption of reduced POM or H₂O₂ by Cr(VI).     

Influences of humic acid, bicarbonate and calcium on Cr(VI) reductive removal by zero-valent iron

The influences of various geochemical constituents, such as humic acid, HCO₃⁻, and Ca²⁺, on Cr(VI) removal by zero-valent iron (Fe⁰) were investigated in a batch setting. The collective impacts of humic acid, HCO₃⁻, and Ca²⁺ on the Cr(VI) reduction process by Fe⁰ appeared to significantly differ from their individual impacts. Humic acid introduced a marginal influence on Fe⁰ reactivity toward Cr(VI) reduction, whereas HCO₃⁻ greatly enhanced Cr(VI) removal by maintaining the solution pH near neutral. The Cr(VI) reduction rate constants (k_obs) were increased by 37.8% and 78.3%, respectively, with 2 mM and 6 mM HCO₃⁻ in solutions where humic acid and Ca²⁺ were absent. Singly present Ca²⁺ did not show a significant impact to Cr(VI) reduction. However, probably due to the formation of passivating CaCO₃, further addition of Ca²⁺ to HCO₃⁻ containing solutions resulted in a decrease of k_obs compared to solutions containing HCO₃⁻ alone. Ca²⁺ enhanced humic acid adsorption led to a minor decrease of Cr(VI) reduction rates. In Ca²⁺-free solutions, humic acid increased the amount of total dissolved iron to 25 mg/l due to the formation of soluble Fe-humate complexes and stably dispersed fine Fe (oxy)hydroxide colloids, which appeared to suppress iron precipitation. In contrast, the coexistence of humic acid and Ca²⁺ significantly promoted the aggregation of Fe (oxy)hydroxides, with which humic acid co-aggregated and co-precipitated. These aggregates would progressively be deposited on Fe⁰ surfaces and impose long-term impacts on the permeability of PRBs.     

Photocatalytic reduction of Cr(VI) in aqueous solutions by UV irradiation with the presence of titanium dioxide

The reduction of Cr(VI) in aqueous solution by UV/TiO2 reduction process was studied under various solution pH values, TiO2 dosages, light intensities, dissolved oxygen levels and other operating conditions. The reduction rates of Cr(VI) by photocatalytic-induced elections were significantly higher for acidic solutions than those for alkaline solutions. Increasing the light intensity would drastically increase the reduction rate of Cr(VI), but was ultimately influenced by the amount of TiO2 present in solutions. The presence of dissolved oxygen had minimum effect on the reduction of Cr(VI) by UV/TiO2 process in acidic solutions. The presence of ethanol might act as scavenger for holes and promoted the photocatalytic reduction of Cr(VI) by electrons. The Cr(VI) adsorbed on the surface of TiO2 particles was observed to be photoreduced to Cr(III) almost completely.     

Photocatalytic transformation and mineralization of 2,4,6-trinitrotoluene (TNT) in TiO2 slurries

An analysis of the photodegradation of TNT in a TiO₂ slurry reactor is presented. The rates and extent of TNT transformation and mineralization are compared for photocatalytic and direct photolytic reactions under conditions of varying light energies and in the presence and absence of oxygen. Certain initial organic transformation products are identified for both photocatalytic and photolytic reactions. Nitrate, nitrite, and ammonium ions are analyzed and the possibility of semiconductor sensitization by colored compounds is considered. TNT was transformed rapidly under each set of photochemical conditions but destruction was faster and more complete with TiO₂ photocatalysis. Transformation by-products were destroyed readily under oxygenated photocatalytic conditions and were observed to be more refractory under direct photolytic conditions. Mass balances performed on carbon and nitrogen revealed that when the TiO₂ photocatalyst was utilized in the presence of oxygen and near u.v. radiation (λ > 340 nm) approx. 90% of the TNT was mineralized and 35% of the total nitrogen was recovered as ammonium ion after 120 min. Among the large number of organic transformation products produced photocatalytically, trinitrobenzoic acid, trinitrobenzene and trinitrophenol have been identified as oxidative intermediate species and dinitroaniline as a reduction product. The photocatalytic transformation of TNT appears to involve both oxidative and reductive steps and sensitization by colored compounds plays no detectable role in degradation.     

Impact of Hydrogen Peroxide on Photocatalytic Destruction of Anionic SAS in a Reactor with Immobilized TiO<Subscript>2</Subscript>

Using sodium dodecylbenzenesulfonate the article showed high efficiency of photocatalytic system H₂O₂/TiO₂/UV for deep destruction (~ 90% in terms of TOC) of anionic SAS in a aqueousmedium (C₀ = 50 mg/dm³, pH₀ 5.9) in a reactor containing wide–porous ceramic block with immobilized TiO₂ on its surface. The TiO₂ film for a long time preserved a stable photocatalytic activity     

Energy efficiency for the removal of non-polar pollutants during ultraviolet irradiation,visible light photocatalysis and ozonation of a wastewater effluent

This study aims to assess the removal of a set of non-polar pollutants in biologically treated wastewater using ozonation, ultraviolet (UV 254 nm low pressure mercury lamp) and visible light (Xe-arc lamp) irradiation as well as visible light photocatalysis using Ce-doped TiO₂. The compounds tracked include UV filters, synthetic musks, herbicides, insecticides, antiseptics and polyaromatic hydrocarbons. Raw wastewater and treated samples were analyzed using stir-bar sorptive extraction coupled with comprehensive two-dimensional gas chromatography (SBSE–CG × GC–TOF–MS). Ozone treatment could remove most pollutants with a global efficiency of over 95% for 209 μM ozone dosage. UV irradiation reduced the total concentration of the sixteen pollutants tested by an average of 63% with high removal of the sunscreen 2-ethylhexyl trans-4-methoxycinnamate (EHMC), the synthetic musk 7-acetyl-1,1,3,4,4,6-hexamethyltetrahydronaphthalene (tonalide, AHTN) and several herbicides. Visible light Ce–TiO₂ photocatalysis reached ∼70% overall removal with particularly high efficiency for synthetic musks. In terms of power usage efficiency expressed as nmol kJ⁻¹, the results showed that ozonation was by far the most efficient process, ten-fold over Xe/Ce–TiO₂ visible light photocatalysis, the latter being in turn considerably more efficient than UV irradiation. In all cases the efficiency decreased along the treatments due to the lower reaction rate at lower pollutant concentration. The use of photocatalysis greatly improved the efficiency of visible light irradiation. The collector area per order decreased from 9.14 ± 5.11 m² m⁻³ order⁻¹ for visible light irradiation to 0.16 ± 0.03 m² m⁻³ order⁻¹ for Ce–TiO₂ photocatalysis. The toxicity of treated wastewater was assessed using the green alga Pseudokirchneriella subcapitata. Ozonation reduced the toxicity of treated wastewater, while UV irradiation and visible light photocatalysis limited by 20–25% the algal growth due to the accumulation of reaction by-products. Three transformation products were identified and tracked along the treatments.     

Gas‐phase removal of indoor volatile organic compounds and airborne microorganisms over mono‐ and bimetal‐modified (Pt,Cu, Ag) titanium(IV) oxide nanocomposites

The photocatalytic deactivation of volatile organic compounds and mold fungi using TiO₂ modified with mono‐ and bimetallic (Pt, Cu, Ag) particles is reported in this study. The mono‐ and bimetal‐modified (Pt, Cu, Ag) titanium(IV) oxide photocatalysts were prepared by chemical reduction method and characterized using XRD, XPS, DR/UV‐Vis, BET, and TEM analysis. The effect of incident light, type and content of mono‐ and bimetallic nanoparticles deposited on titanium(IV) oxide was studied. Photocatalytic activity of as‐prepared nanocomposites was examined in the gas phase using LEDs array. High photocatalytic activity of Ag/Pt‐TiO₂ and Cu/Pt‐TiO₂ in the reaction of toluene degradation resulted from improved efficiency of interfacial charge transfer process, which was consistent with the fluorescence quenching effect revealed by photoluminescence (PL) emission spectra. The photocatalytic deactivation of Penicillium chrysogenum, a pathogenic fungi present in the indoor environment, especially in a damp or water‐damaged building using mono‐ and bimetal‐modified (Pt, Cu, Ag) titanium(IV) oxide was evaluated for the first time. TiO₂ modified with mono‐ and bimetallic NPs of Ag/Pt, Cu, and Ag deposited on TiO₂ exhibited improved fungicidal activity under LEDs illumination than pure TiO₂.     

Combined permeable pavement and photocatalytic titanium dioxide oxidation system for urban run‐off treatment and disinfection

Permeable pavement systems (PPS) are frequently associated with high removal efficiencies for water quality parameters. Their effluent can, therefore, be recycled, for example, for sprinkling onto gardens. Nevertheless, some stakeholders fear that potentially pathogenic organisms within the treated run‐off could be too high, and therefore they request disinfection before recycling. The aim of this paper is, therefore, to assess the efficiency of a batch flow combined titanium dioxide (TiO₂) and ultraviolet (UV) light photocatalytic reactor in removing water‐borne microbial contaminants from the effluent of PPS. Combined TiO₂ and UV photocatalytic reaction times between 80 and 100 min were required for the complete removal of Escherichia coli, total coliforms and faecal Streptococci, which had mean initial counts of 1.5 × 10⁷, 4.4 × 10⁶ and 6.9 × 10⁵ colony‐forming units (CFU) per 100 mL, respectively. In comparison, UV disinfection alone resulted in insignificant microbial removal. Suspended TiO₂ powder was more effective than small immobilised TiO₂ crystals.