Synthesis and dye-sensitized solar cell performance of nanorods/nanoparticles TiO2 from high surface area nanosheet TiO2

High surface area nanosheet TiO2 with mesoporous structure were synthesized by hydrothermal method at 130 degrees C for 12 h. The samples characterized by XRD, SEM, TEM, SAED, and BET surface area. The nanosheet structure was slightly curved and approximately 50-100 nm in width and several nanometers in thickness. The as-synthesized nanosheet TiO2 had average pore diameter about 3-4 nm. The BET surface area and pore volume of the sample were about 642 m(2)/g and 0.774 cm(3)/g, respectively. The nanosheet structure after calcinations were changed into nanorods/nanoparticles composite with anatase TiO2 structure at 300-500 degrees C (10-15 nm in rods diameter and about 5-10 nm in particles diameter). The solar energy conversion efficiency (eta) of the cell using nanorods/nanoparticles TiO2 (from the nanosheet calcined at 450 degrees C for 2 h) with mesoporous structure was about 7.08% with Jsc of 16.35 mA/cm(2), Voc of 0.703 V and ff of 0.627; while eta of the cell using P-25 reached 5.82% with Jsc of 12.74 mA/cm(2), Voc of 0.704 V, and ff of 0.649.     

Synthesis and photocatalytic property of porous TiO2 microspheres

Porous TiO₂ microspheres were prepared in air atmosphere using sol-gel-adding electrolyte method, which is simple and reproducible. The TEM image shows that the diameter of microspheres is around 550 nm. BET measurement indicates that TiO₂ microspheres are of high specific surface area and have a uniform pore size distribution with a mean pore size of 4.4 nm. The pores of the TiO₂ microspheres are monodispersive, mesoporous and interconnecting. XRD shows that calcination at 500 °C transformed the TiO₂ microspheres from amorphous to anatase phase. The degradation experiment demonstrates that the photocatalytic activity of TiO₂ microspheres toward methylene blue dye photodegradation is more efficient than that of the commercial TiO₂ powder. Moreover, the microspheres can be easily removed from the treated solution.     

Hydrogen evolution from aqueous methanol solution on mesoporous titania prepared by a process combining evaporation induced self-assembly and spray pyrolysis

Mesoporous TiO₂ powders were prepared in 1 min from an aqueous mixture of chelated complex titanium precursor and tri-block copolymer by using a process combining evaporation induced self-assembly (EISA) and spray pyrolysis. Photocatalytic activity was evaluated by measuring the rate of hydrogen evolution from methanol solution. The prepared powders were mainly anatase phase and had worm-like pores. Crystallite size was in the range from 7.8 to 18.6 nm in diameter. The mesoporous TiO₂ powders calcined at 823 K had surface area of 144 m² g⁻¹ and high pore volume of 0.33 cm³ g⁻¹. Pore size distribution was also narrow. In addition, it had high light absorption intensity below 350 nm. The rate of hydrogen evolution was by a factor of six higher than the rate measured with commercial nano-sized TiO₂ powder (Degussa P-25). Unique structural and optical properties, which were mainly originated from our new combined process of EISA and spray pyrolysis, contributed to the enhanced rate of hydrogen evolution.     

An aqueous sol-gel synthesis of chromium(III) doped mesoporous titanium dioxide for visible light photocatalysis

Nanoparticles of titanium dioxide doped with Cr³⁺ ions have been prepared through an aqueous sol-gel method. The mesoporous nature of both pure and Cr³⁺ doped TiO₂ powders, with specific surface area of 7.4 and 6.6 m² g⁻¹, respectively, is maintained even at calcination temperature of 800 °C. The transformation of TiO₂ from the anatase to rutile phase is suppressed up to 800 °C by Cr³⁺ ion doping. Even though surface area values are decreased, the doped materials show improved photocatalytic activity, which may be due to increased crystallinity of the anatase phase without the formation of rutile. Doped materials have a red-shift in the band gap energy and hence, photoactivity under visible light. The rate of photodegradation of methylene blue dye for both pure and doped TiO₂ under visible light has been monitored in this study. The 0.25 mol% Cr(III) doped photocatalyst, calcined at 800 °C, shows the highest photocatalytic activity under visible light with a rate constant of ∼15.8 × 10⁻³ min⁻¹, which is nearly three times higher than that of commercially available Degussa P25 titania (5.8 × 10⁻³ min⁻¹).     

Experimental design in the electrodeposition process of porous composite Ni–P + TiO2 coatings

In this paper, an environmentally friendly electroplating process of the composite Ni–P + TiO₂ coatings was developed. Such coatings were prepared by in situ codeposition of Ni–P with TiO₂ powder (anatase) on a polycrystalline copper substrate from the nickel-plating bath in which titanium dioxide particles were held in suspension. The codeposition was carried out under galvanostatic conditions on a rotating disc electrode. To optimize the production conditions of the Ni–P coatings modified with TiO₂ by the method of mathematical statistics, the Hartley's polyselective quasi D optimum plan of experiments was used. The relationship between the percentage content in the electrodeposited composite Ni–P + TiO₂ coatings (z) and the electrodeposition parameters like cathodic current density (j_dep), bath temperature (T) as well as content of TiO₂ powder suspended in the galvanic bath (c), has been described by the adequate cubic polynomial equation and illustrated graphically. Based on the Hartley's plan it can be stated that the maximal TiO₂ content of 28.7 at.% in the Ni–P + TiO₂ coating can be obtained for the following optimal parameters of the electrodeposition process: j_dep = 0.05 A cm⁻², c = 99 g dm⁻³ and T = 40 °C. The chemical and physical characteristics of the coating obtained under such optimum conditions, have been presented. The deposit exhibits the presence of TiO₂ particles embedded into the amorphous Ni–P matrix. It has been ascertained that embedding of TiO₂ powder to the amorphous Ni–P matrix leads to the production of deposits with large surface area. Such electrochemical codeposition method may be a good alternative in the field of porous composite coatings used in gas evolution.     

High-temperature anomalies of dielectric constant in TiO2 thin films

Anatase and rutile TiO₂ thin films were prepared by chemical vapor deposition with precursors Ti(OPrⁱ)₄ and Ti(dpm)₂(OPrⁱ)₂ (dpm = 2,2,6,6-tetramethylheptane-3,5-dione and Prⁱ = isopropyl), respectively. The dielectric properties of TiO₂ thin films have been studied in 20-1100 K temperature range in air, in controlled Ar/O₂ atmospheres, and in vacuum with silicon-based metal-insulator-semiconductor Au/TiO₂/Si capacitors. High-temperature (T_c ∼ 980 K) anomalous behavior of dielectric constant was observed in both anatase and rutile TiO₂ thin films.     

Microstructure and photocatalytic activity of mesoporous TiO2 film coated on an aluminum foam

A TiO₂ film was synthesized via a surfactant assisted sol-gel process and dip-coated on the surface of an open-celled aluminum foam. The film shows a typical mesoporous structure composed of anatase crystalline grains with the average size of 10 nm, and has the thickness of about 3.5 μm as well as the BET surface area of 78.1 m²/g. It exhibits high photocatalytic efficiency toward the decomposition of formaldehyde at continuous flow mode. The relatively small grain size of TiO₂ and relatively thick mesoporous structure, which is favorable for high photochemical activity and the mass transfer of the reactants, should be responsible for the properties.     

Synthesis of mesoporous β-Ga2O3 nanorods using PEG as template: Preparation, characterization and photocatalytic properties

Mesoporous wide bandgap semiconductors offer high photocatalytic oxidation and mineralization activities. In this study, mesoporous β-Ga₂O₃ diamond nanorods with 200-300 nm in diameter and 1.0-1.2 μm in length were synthesized via a urea-based hydrothermal method using polyethylene glycol (PEG) as template agent. The UV photocatalytic oxidation activity of β-Ga₂O₃ for gaseous toluene was evaluated, and 7 kinds of intermediates were monitored online by a proton transfer reaction mass spectrometry. Photoluminescence spectra manifested that the dosage and molecular weight of PEG are crucial for formation of vacancies and photocatalytic oxidation activities. A PEG-assisted hydrothermal formation mechanism of mesoporous β-Ga₂O₃ diamond nanorods was proposed. Based on the health risk influence index (η) of the intermediates, the calculated health risks revealed that the β-Ga₂O₃ nanorods with a η value of 9.6 are much safer than TiO₂ (η = 17.6).     

Removal of fluoride from aqueous solution by polypyrrole/Fe3O4 magnetic nanocomposite

Highly efficient visible light TiO₂ photocatalyst was prepared by the sol-gel method at lower temperature (≤300 °C), and characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), Fourier-transform infrared spectroscopy (FTIR), UV-vis diffuse reflectance spectroscopy (UV-vis DRS), X-ray photoelectron spectroscopy (XPS), Raman spectroscopy and differential scanning calorimetry-thermogravimetric analysis (DSC-TGA). The effects of the heat treatment temperature and time of the as-prepared TiO₂ on its visible light photocatalytic activity were investigated by monitoring the degradation of methyl orange solution under visible light irradiation (wavelength ≥ 400 nm). Results show that the as-prepared TiO₂ nanoparticles possess an anatase phase and mesoporous structure with carbon self-doping and visible photosensitive organic groups. The visible light photocatalytic activity of the as-prepared TiO₂ is greatly higher than those of the commercial TiO₂ (P-25) and other visible photocatalysts reported in literature (such as PPy/TiO₂, P3HT/TiO₂, PANI/TiO₂, N-TiO₂ and Fe³⁺-TiO₂) and its photocatalytic stability is excellent. The reasons for improving the visible light photocatalytic activity of the as-prepared TiO₂ can be explained by carbon self-doping and a large amount of visible photosensitive groups existing in the as-prepared TiO₂. The apparent optical thickness (τ_app), local volumetric rate of photo absorption (LVRPA) and kinetic constant (k_T) of the photodegradation system were calculated.     

Sol-gel synthesis of titania hollow spheres

TiO₂ hollow spheres are prepared by a convenient sol-gel method at room temperature. The products were characterized by XRD, FESEM, TEM and FT-IR. It was found that these spheres are hollow inside with outer diameters of 200-500 nm. The average mesoporous diameter is about 9.8 nm. And the BET surface area and specific pore volume are about 161.9 m²/g and 0.441 cm³/g, respectively.     

Facile synthesis of mesoporous core-shell TiO2 nanostructures from TiCl3

The present study reports the synthesis and formation process of mesoporous core-shell TiO₂ nanostructures by employing a glucose-assisted solvothermal process using water-ethanol mixture as solvent and subsequent calcination process at 550 °C for 4 h. X-ray diffraction, field emission scanning electron microscopy, transmission electron microscopy and nitrogen adsorption-desorption analysis were used to investigate the structural properties of these nanostructures. By optimizing the preparation conditions, especially the contents of water and ethanol in the mixture solvent, mesoporous core-shell TiO₂ nanostructures were obtained. These mesoporous nanostructures have anatase phase and exhibit the superior photocatalytic activity. This synthesis route is facile due to the usage of stable and low-cost Ti precursor such as TiCl₃ and is thus applicable for large-scale production.     

A low-temperature process to synthesize rutile phase TiO2 and mixed phase TiO2 composites

This works employed K₂Ti₄O₉, a novel Ti source, to prepare TiO₂ powders. By a “low-temperature dissolution-reprecipitation process” (LTDRP), rutile phase TiO₂ was successfully synthesized after reacting at 50 °C for 48 h. The obtained sample showed a specific surface area about 45 m²/g, and excellent activity in photo-destruction of NO_x gas. The coupling of rutile phase TiO₂ with commercial anatase TiO₂ showed significant effect in further enhancing the photocatalytic activity.     

Sonochemical preparation of TiO2 nanoparticles in the ionic liquid 1-(3-hydroxypropyl)-3-methylimidazolium-bis(trifluoromethylsulfonyl)amide

Spherical shaped anatase nanoparticles (ø 5 nm) have been synthesized in the ionic liquid 1-(3-hydroxypropyl)-3-methylimidazolium-bis(trifluoromethanesulfonyl)amide from titanium tetraisopropoxide by ultrasound assisted synthesis under ambient conditions. XRD, EDX, TEM, XPS, Raman, UV–vis, PL and BET measurements have been employed for characterization of the nanostructure of as-prepared TiO₂. XRD and Raman measurements both show that the obtained material is crystalline with anatase structure. The morphology of TiO₂ nanoparticles was characterized by transmission electron microscopy (TEM). The bandgap of the TiO₂ nanocrystals estimated from XRD and UV–vis measurements is about 3.3 eV. The surface area of a typical sample is 177 m² g⁻¹. The synthesized anatase nanocrystals show good photocatalytic activity in the degradation of methylorange.     

Effects of thermal treatment of nanostructured trititanates on their crystallographic and textural properties

Nanostructured titanates (TTNT) with general formula Na_xH_2−xTi₃O₇·nH₂O were synthesized by hydrothermally reacting different TiO₂ anatase (distinct crystal sizes) with NaOH at 120 °C followed by washing with water or diluted acid and drying of the precipitate. The resulting powders with different sodium contents were submitted to various calcination temperatures up to 800 °C and each calcined product was characterized as for its phase structure, composition, crystallite size and textural properties, namely BET surface area, mesopore volume and pore size distribution. Thermal transformations of TTNT samples were investigated by monitoring the modifications on crystallographic (X-ray diffraction) and textural (N₂ desorption isotherms) properties, revealing the influence of the type of starting anatase and sodium content over the stability of TTNT. Moreover, a detailed study on the reduction of the interlayer distance in TTNT samples upon thermal treatment allowed corroborating the formation of an intermediate nanostructured hexatitanate, just before phase transformation into the corresponding TiO₂ polymorphs and/or titanate crystals, depending on the sodium content and calcination temperature.     

Fabrication and photocatalytic activity of porous TiO2 nanowire microspheres by surfactant-mediated spray drying process

A novel, porous TiO₂ nanowire microsphere with a diameter of 3-8 μm was successfully fabricated via spray drying of TiO₂ nanowire suspension with the assistance of surfactant (F127). The products were characterized by FESEM, XRD and N₂ adsorption-desorption analysis and results revealed that the resulting TiO₂ nanowire microspheres possessed a hierarchically macro/mesoporous structure, as well as a high BET surface area of 38.2 m²/g. Systematic studies showed that the presence of surfactant in the suspension feed for spray drying was critical in the formation of porous microspheres. The structure of the fabricated microspheres depends on the nanowire concentration in the feed. The TiO₂ nanowire microspheres exhibited significant photocatalytic degradation of Methylene blue (MB) as compared to commercial TiO₂ nanoparticles (P25). It was also revealed that the microspheres have excellent stability on photocatalytic activity and mechanical strength, which are both crucial factors when considering reuse of these photocatalysts.     

Properties of TiO2 prepared by acid treatment of BaTiO3

TiO₃ powders were prepared by acid treatment of BaTiO₃ and their properties were investigated. The BaTiO₃ powder was subjected to HNO₃ in concentrations ranging from 10⁻³ to 8 M at 90 °C for 0.5-6 h. Dissolution of BaTiO₃ and precipitation of TiO₂ occurred at acid concentrations of 2-5 M. BaTiO₃ dissolves completely to form a clear solution at reaction times of 0.5-1 h, but a rutile precipitate is formed after 2 h of acid treatment. By contrast, anatase is precipitated by adjusting the pH of the clear solution to 2-3 using NaOH or NH₄OH solution. The rutile crystals were small and rod-shaped, consisting of many small coherent domains connected by grain boundaries with small inclination angles and edge dislocations, giving them a high specific surface area (S_BET). With increasing HNO₃ concentration, the S_BET value increased from 100 to 170 m²/g while the crystallite size decreased from 25 to 11 nm. The anatase crystals obtained here were very small equi-axial particles with a smaller crystallite size than the rutile and S_BET values of about 270 m²/g (higher than the rutile samples). The photocatalytic activity of these TiO₂ was determined from the decomposition rate of Methylene Blue under ultraviolet irradiation. Higher decomposition rates were obtained with larger crystallite sizes resulting from heat treatment. The maximum decomposition rates were obtained in samples heated at 500-600 °C. The photocatalytic activity of the TiO₂ was found to depend more strongly on the sample crystallite size than on S_BET.     

Solid-phase reaction synthesis of mesostructured tungsten disulfide material with a high specific surface area

A mesostructured tungsten disulfide (WS₂) material was prepared through a solid-phase reaction utilizing ammonium tetrathiotungstate as the precursor and n-octadecylamine as the template. The as-synthesized WS₂ material was characterized by X-ray powder Diffraction (XRD), Low-temperature N₂ Adsorption (BET method), Scanning Electron Microscopy (SEM), and Transmission Electron Microscopy (TEM). The characterization results indicate that the WS₂ material has the typical mesopore structure (3.7 nm) with a high specific surface area (145.9 m²/g), and large pore volume (0.18 cm³/g). This approach is novel, green and convenient. The plausible mechanism for the formation of the mesostructured WS₂ material is discussed herein.     

An easier method of preparation of mesoporous anatase TiO2 nanoparticles via ultrasonic irradiation

Mesoporous anatase TiO₂ nanopowder was synthesised by the sol–gel method using ultrasonic irradiation. This method is simple and faster for the synthesis of phase pure mesoporous anatase TiO₂ nanopowder. The product is characterised by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron spectroscopy (TEM), thermo gravimetric analysis, Brunauer–Emmett–Teller (BET) surface area, UV–visible diffuse reflectance spectroscopy and Fourier transform infrared spectroscopy. Analysis of XRD patterns, SEM and TEM image shows that the average particles size is of 19.9 nm and has an anatase structure. The mesoporous nature was determined by the BET method using the Barrett–Joyner–Halenda (BJH) model.     

Crystal growth and structure refinement of monoclinic Li2TiO3

Colorless platelet crystals of monoclinic Li₂TiO₃ with a maximum size of 5.0 mm × 5.0 mm × 0.5 mm were successfully grown by a flux method at 1373 K using a LiBO₂-Li₂O system flux. The stoichiometric chemical composition of Li₂TiO₃ was determined by the SEM-EDX, ICP-AES and density measurement using the single crystal samples. The thermal conductivity of the Li₂TiO₃ single crystals was evaluated using hot-disk method. A single-crystal X-ray diffraction study confirmed the monoclinic Li₂SnO₃-type structure, space group C2/c and the lattice parameters of a = 5.0623(5) Å, b = 8.7876(9) Å, c = 9.7533(15) Å, β = 100.212(11)°, and V = 427.01(9) Å³. The crystal structure was refined to the conventional values of R = 2.4% and wR=3.3% for 2187 independent observed reflections. The cationic arrangement of (LiTi₂) layers in Li₂TiO₃ was precisely revealed by the structure analysis.     

Templated synthesis of nanosized mesoporous carbons

Mesoporous carbon materials formed by nanosized particles have been synthesized by means of a nanocasting technique based on the use of mesostructured silica materials as templates. We found that the modification of the chemical characteristics of the surfactant employed allows mesostructured silica materials with particle sizes <100 nm to be synthesised. The mesoporous carbons obtained from these silica materials retain the structural properties of the silica used as template and consequently they have a particle size in the 20-100 nm range. These carbons exhibit large BET surfaces areas (up to 1300 m² g⁻¹) and high pore volumes (up to 2.5 cm³ g⁻¹), a framework confined porosity made up of uniform mesopores (3.6 nm) and an additional textural porosity arising from the interparticle voids between the sub-micrometric particles. The main advantage of nanometer-sized mesoporous carbons in relation to the micrometer-sized carbons is that they have enhanced mass transfer rates, which is important for processes such as adsorption or catalysis.