Sintering and dielectric properties of 0.88Al2O3-0.12TiO2 microwave ceramics by glass addition

The microwave characteristics and the microstructures of 0.88Al₂O₃-0.12TiO₂ with various amounts of MgO-CaO-SiO₂-Al₂O₃ (MCAS) glass sintered at different temperatures have been investigated. The sintering temperature can be lowered to 1300 °C by the addition of MCAS glass. The densities, dielectric constants (ε_r) and quality values (Q×f) of the MCAS-added 0.88Al₂O₃-0.12TiO₂ ceramics decrease with the increase of MCAS glass content. The temperature coefficients of the resonant frequency (τ_f) are shifted to more negative values as the MCAS content or the sintering temperatures increase. The change of the crystalline phases of Al₂TiO₅ phase and rutile-TiO₂ phase has profound effects on the microwave dielectric properties of the MCAS-added Al₂O₃-TiO₂ ceramics. As sintered at 1250 °C, 0.88Al₂O₃-0.12TiO₂ ceramics with 2 wt.% MCAS glass addition exists a ε_r value of 8.63, a Q×f value of 9578 and a τ_f value of +5 ppm/°C.     

Microwave dielectric properties and microstructures of CuO- and ZnO-doped LaAlO3 ceramics

The microwave dielectric properties and the microstructures of 0.25 wt.% CuO-doped LaAlO₃ ceramics with ZnO additions have been investigated. The sintered LaAlO₃ ceramics are characterized by X-ray diffraction spectra and scanning electron microscopy (SEM). Tremendous reduction in sintering temperature can be achieved with the addition of sintering aids CuO and ZnO. The ceramic samples show that dielectric constants (ε_r) of 22−24 and Q×f values of 33,000−57,000 (at 9.7 GHz) can be obtained at low sintering temperatures 1340−1460°C. The temperature coefficient of resonant frequency varies from −24 to −48 ppm/°C. At the level of 0.25 wt.% CuO and 1 wt.% ZnO additions, LaAlO₃ ceramics possesses a dielectric constant (ε_r) of 23.4, a Q×f value of 57,000 (at 9.7 GHz) and a τ_f value of −38 ppm/°C at 1400°C for 2 h.     

Influence of Bi2O3 and CuO addition on low-temperature sintering and dielectric properties of Ba0.6Sr0.4TiO3 ceramics

In this study, we tried to lower the sintering temperature of Ba_0.6Sr_0.4TiO₃ (BST) ceramics by several kinds of adding methods of Bi₂O₃, CuO and CuBi₂O₄ additives. The effects of different adding methods on the microstructures and the dielectric properties of BST ceramics have been studied. In the all additive systems, the single addition of CuBi₂O₄ was the most effective way for lowering the sintering temperature of BST. When CuBi₂O₄ of 0.6 mol% was mixed with starting BST powders and sintered at 1100 °C, the derived ceramics demonstrated dense microstructure with a low dielectric constant (? = 4240), low dielectric loss (tan δ = 0.0058), high tunability (Tun = 38.3%) and high Q value (Q = 251). It was noteworthy that the sintering temperature was significantly lowered by 350 °C compared with no-additive system, and the derived ceramics maintained the excellent microwave dielectric properties corresponding to pure BST.     

Low-temperature firing and microwave dielectric properties of ZnO-Nb2O5-TiO2-SnO2 ceramics with CuO-V2O5

The effects of CuO-V₂O₅ addition on the sintering temperature and microwave dielectric properties of ZnO-Nb₂O₅-TiO₂-SnO₂ were investigated. The CuO-V₂O₅ addition lowered the sintering temperature of ZnO-Nb₂O₅-TiO₂-SnO₂ ceramics effectively from 1150 to 860 °C due to the liquid-phase effect of Cu₂V₂O₇ and Cu₃(VO₄)₂, as observed by XRD. The microwave dielectric properties were found to strongly correlate with the sintering temperature and the amount of CuO-V₂O₅ addition. The maximum Qf values decreased with increasing CuO-V₂O₅ content, due to the formation of the second phase, Cu₃(VO₄)₂ and CuNbO₃. Zero τ_f value can be obtained by properly adjusting the sintering temperature. At 860 °C, ZnO-Nb₂O₅-TiO₂-SnO₂ ceramics with 1.5 wt.% CuO-V₂O₅ gave excellent microwave dielectric properties: ?_r = 42.3, Qf = 9000 GHz and τ_f = 8 ppm/°C.     

Effect of B2O3-Bi2O3-SiO2-ZnO glass on the sintering and microwave dielectric properties of 0.83ZnAl2O4-0.17TiO2

The 0.83ZnAl₂O₄-0.17TiO₂ (ZAT) ceramics were synthesized by solid state ceramic route. The effect of 27B₂O₃-35Bi₂O₃-6SiO₂-32ZnO (BBSZ) glass on the microwave dielectric properties of ZAT was investigated. The crystal structure and the microstructure of the ceramic-glass composites were studied by X-ray diffraction and scanning electron microscopic techniques. The low frequency dielectric loss was measured at 1 MHz. The dielectric properties of the sintered samples were measured in the microwave frequency range by the resonance method. Addition of 0.2 wt% of BBSZ improved the dielectric properties with quality factor (Q_u × f) > 120,000 GHz, temperature coefficient of resonant frequency (τ_f) = −7.3 ppm/°C and dielectric constant (?_r) = 11.7. Addition of 10 wt% of BBSZ lowered the sintering temperature to about 950 °C with Q_u × f > 10,000 GHz, ?_r = 10 and τ_f = −23 ppm/°C. The reactivity of 10 wt% BBSZ added ZAT with silver was also studied. The results show that ZAT doped with suitable amount of BBSZ glass is a possible material for low-temperature co-fired ceramic (LTCC) application.     

Processing, dielectric properties and impedance characteristics of Na0.5Bi0.5Cu3Ti4O12 ceramics

Na_0.5Bi_0.5Cu₃Ti₄O₁₂ (NBCTO) ceramics were prepared by conventional solid-state reaction method. The phase structure, microstructure and dielectric properties of NBCTO ceramics sintered at various temperatures with different soaking time were investigated. Pure NBCTO phase could be obtained with increasing the temperature and prolonging the soaking time. High dielectric permittivity (13,495) and low dielectric loss (0.031) could be obtained when the ceramics were sintered at 1000 °C for 7.5 h. The ceramics sintered at 1000 °C for 7.5 h also showed good temperature stability (−4.00 to −0.69%) over a large temperature range from −50 to 150 °C. Complex impedances results revealed that the grain was semiconducting and the grain boundaries was insulating. The grain resistance (R_g) was 12.10 Ω cm and the grain boundary resistance (R_gb) was 2.009 × 10⁵ Ω cm when the ceramics were sintered at 1000 °C for 7.5 h.     

(5 − x)BaO-xMgO-2Nb2O5 ceramics prepared using a reaction-sintering process

(5 − x)BaO-xMgO-2Nb₂O₅ (x = 0.5 and 1; 5MBN and 10MBN) microwave ceramics prepared using a reaction-sintering process were investigated. Without any calcinations involved, the mixture of BaCO₃, MgO, and Nb₂O₅ was pressed and sintered directly. MBN ceramics were produced after 2-6 h of sintering at 1350-1500 °C. The formation of (BaMg)₅Nb₄O₁₅ was a major phase in producing 5MBN ceramics, and the formation of Ba(Mg_1/3Nb_2/3)O₃ was a major phase in producing 10MBN ceramics. As CuO (1 wt%) was added, the sintering temperature dropped by more than 150 °C. We produced 5MBN ceramics with these dielectric properties: ?_r = 36.69, Qf = 20,097 GHz, and τ_f = 61.1 ppm/°C, and 10MBN ceramics with these dielectric properties: ?_r = 39.2, Qf = 43,878 GHz, and τ_f = 37.6 ppm/°C. The reaction-sintering process is a simple and effective method for producing (5 − x)BaO-xMgO-2Nb₂O₅ ceramics for applications in microwave dielectric resonators.     

Improved microwave dielectric properties of B2O3-doped Nd(Co1/2Ti1/2)O3 ceramics with near zero temperature coefficient of resonant frequency

The microwave dielectric properties and the microstructures of Nd(Co_1/2Ti_1/2)O₃ ceramics prepared by conventional solid-state route have been studied. The prepared Nd(Co_1/2Ti_1/2)O₃ exhibited a mixture of Co and Ti showing 1:1 order in the B-site. It is found that low-level doping of B₂O₃ (up to 0.75 wt.%) can significantly improve the density and dielectric properties of Nd(Co_1/2Ti_1/2)O₃ ceramics. Nd(Co_1/2Ti_1/2)O₃ ceramics with additives could be sintered to a theoretical density higher than 98.5% at 1320 °C. Second phases were not observed at the level of 0.25-0.75 wt.% B₂O₃ addition. The temperature coefficient of resonant frequency (τ_f) was not significantly affected, while the dielectric constants (?_r) and the unloaded quality factors Q were effectively promoted by B₂O₃ addition. At 1320 °C/4 h, Nd(Co_1/2Ti_1/2)O₃ ceramics with 0.75 wt.% B₂O₃ addition possesses a dielectric constant (?_r) of 27.2, a Q × f value of 153,000 GHz (at 9 GHz) and a temperature coefficient of resonant frequency (τ_f) of 0 ppm/°C. The B₂O₃-doped Nd(Co_1/2Ti_1/2)O₃ ceramics can find applications in microwave devices requiring low sintering temperature.     

Structural and impedance properties of KBa2V5O15 ceramics

The polycrystalline sample of KBa₂V₅O₁₅ ceramics was prepared by a mixed oxide method at low temperature (i.e., at 560 °C). The formation of the compound was confirmed using an X-ray diffraction technique at room temperature. Scanning electron micrograph of the material showed uniform grain distribution on the surface of the sample. Detailed studies of dielectric properties of the compound as a function of temperature at different frequencies suggest that the compound has a dielectric anomaly of ferroelectric to paraelectric type at 323 °C, and exhibits diffuse phase transition. Electrical properties of the material were analyzed using a complex impedance technique. The Nyquists plot showed the presence of both grain (>10³ Hz) and the grain boundary (<10³ Hz) effects in the material. Studies of electrical conductivity over a wide temperature range suggest that the compound exhibits the negative temperature coefficient of resistance behavior. The ac conductivity spectrum was found to obey Jonscher's universal power law.     

Low temperature sintering and microwave dielectric properties of SmAlO3 ceramics

The effects of sintering aids on the microstructures and microwave dielectric properties of SmAlO₃ ceramics were investigated. CuO and ZnO were selected as sintering aids to lower the sintering temperature of SmAlO₃ ceramics. With the additions, the sintering temperature of SmAlO₃ can be effectively reduced from 1650 to 1430°C. The crystalline phase exhibited no phase differences at low addition level while Sm₄Al₂O₉ appeared as a second phase as the doping level was over 0.5 wt.%. In spite of the additions, the dielectric constants showed no significant change and ranged 19-21. However, the quality factor Q×f was strongly dependent upon the type and amount of additions. The Q×f values of 51,000 and 41,000 GHz could be obtained at 1430°C with 0.25 wt.% CuO and ZnO additions, respectively. The temperature coefficients depended on the additions and varied from −40 to −65 ppm/°C. Results of X-ray diffractions, EDS analysis and scanning electron microscopy were also presented.     

Crystallographic and dielectric properties of barium-substituted Pb(Mg1/3Ta2/3)O3 ceramics

Ceramic powders of (Ba,Pb)Pb(Mg_1/3Ta_2/3)O₃ were prepared via a B-site precursor route. Crystal symmetries and lattice parameters were determined. Monophasic perovskite was developed after the two-step reaction process, in which the lattice parameters showed linear changes in the entire composition range. Dielectric responses of the ceramics with compositional and frequency changes were investigated. The results were also compared with the (Ba,Pb)(Zn_1/3Ta_2/3)O₃ data.     

Study on properties of CaO-SiO2-B2O3 system glass-ceramic

Low temperature co-fired ceramic (LTCC) is prepared by sintering a glass selected from CaO-SiO₂-B₂O₃ system, and its sintered bodies are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). It is found that the optimal sintering temperature for this glass-ceramic is 820 °C for 15 min, and the major phases of this material are CaSiO₃, CaB₂O₄ and SiO₂. The glass-ceramic possesses excellent dielectric properties: ?_r = 6.5, tan δ < 2 × 10⁻³ at 10 MHz, temperature coefficient of dielectric constant about −51 × 10⁻⁶ °C⁻¹ and coefficient of thermal expansion about 8 × 10⁻⁶ °C⁻¹ at 20-400 °C. Thus, this material is supposed to be suitable for the tape casting process and be compatible with Ag electrode, which could be used as the LTCC materials for the application in wireless communications.     

Low temperature sintering and properties of piezoelectric PZT-PFW-PMN ceramics with YMnO3 addition

Low temperature sintering of Pb(Zr,Ti)O₃-Pb(Fe_2/3W_1/3)O₃-Pb(Mn_1/3Nb_2/3)O₃ (PZT-PFW-PMN) quaternary piezoelectric ceramics were studied with the use of YMnO₃ as sintering aid. The sintering aid improved the sinterability of PZT-PFW-PMN ceramics due to the effect of YMnO₃ liquid phase. The effects of YMnO₃ contents and sintering temperature on the phase structure, density, dielectric and piezoelectric properties were investigated. The results show that the sintering temperature can be decreased and the electrical properties can be maintained by the YMnO₃ addition. The optimized properties were obtained by doping 0.30 wt.% YMnO₃ and sintering at 1020 °C, which are listed as follows: d₃₃ = 341 pC/N, K_p = 0.57, Q_m = 1393, tan δ = 0.0053, T_c = 304 °C, P_r = 17.13 μC/cm² and E_c = 11.15 kV/cm, which make this system be a promising material for multilayer piezoelectric actuator and transformer applications.     

Photocatalytic properties of TiO2-P2O5 glass ceramics

Binary TiO₂-P₂O₅ glasses with 69 mol% and 76 mol% TiO₂ were prepared and converted into glass ceramics by heat-treatments. XRD measurements show that the main crystalline phases precipitated in the glass ceramics are anatase-type TiO₂ crystals or (TiO)₂P₂O₇ crystals, depending on the concentration of titanium constituent. Photocatalytic activities of the glass ceramics were evaluated by the decomposition of methylene blue (MB) and measuring the water contact angle. It is found that the glass ceramics containing anatase crystals exhibit both photocatalytic oxidation activity and highly photo-induced hydrophilicity under UV irradiation with intensity of 1.0 mW/cm².     

Microwave dielectric properties of (Pb1−3x/2Lax)(Mg1/2W1/2)O3

La modified Pb(Mg_1/2W_1/2)O₃ were prepared by solid-state reaction process, and the sintering behavior, microstructure and microwave dielectric properties were investigated by X-ray powder diffraction (XRD), Raman scattering and HP network analyzer in this paper. A series of single phase perovskite type solid solutions with A-site vacancies (Pb_1−3x/2La_x(Mg_1/2W_1/2)O₃ (0 ≤ x ≤ 2/3)) were formed. The solid solution took cubic perovskite type structure (Fm3m) with random distribution of A-site vacancies when 0 < x < 0.5, and tetragonal or orthorhombic structure with the ordering of A-site vacancies when 0.5 ≤ x ≤ 2/3. The dielectric constant and temperature coefficient of resonant frequency decrease with increasing La content. Relatively good combination microwave dielectric properties were obtained for x = 0.56: ?_r = 28.7; Q × f = 18098; and τ_f = −5.8 ppm/°C.     

Microwave dielectric properties and microstructures of MgTa2O6 ceramics with CuO addition

The effect of CuO addition on the microstructures and the microwave dielectric properties of MgTa₂O₆ ceramics has been investigated. It is found that low level-doping of CuO (up to 1 wt.%) can significantly improve the density of the specimens and their microwave dielectric properties. Tremendous sintering temperature reduction can be achieved due to the liquid phase effect of CuO addition observed by scanning electronic microscopy (SEM). The sintered samples exhibit excellent microwave dielectric properties, which depend upon the liquid phase and the sintering temperature. With 0.5 wt.% CuO addition, MgTa₂O₆ ceramic can be sintered at 1400 °C and possesses a dielectric constant (_r) of 28, a Q × f value of 58000 GHz and a temperature coefficient of resonant frequency (τ_f) of 18 ppm/°C.     

Effects of complex substitution of La and Nd for Bi on the microwave dielectric properties of BiNbO4 ceramics

La₂O₃ and Nd₂O₃ were used to substitute Bi₂O₃ and the effects of complex substitution on the sintering behavior and the microwave dielectric properties of BiNbO₄ ceramics were studied. With 0.5 wt.% CuO-V₂O₅ mixtures addition, all of the Bi_1−x(La_0.38Nd_0.62)_xNbO₄ ceramics could be densified below 920 °C. The triclinic phases are identified in Bi_1−x(La_0.38Nd_0.62)_xNbO₄ ceramics with x=0.01 sintered at 820 °C and the triclinic intensities increase with increasing the x value and sintering temperature. The saturated bulk density slightly decreases from 7.17 to 7.13 g/cm³ and the ε_r value from 44.24 to 42.76 with increasing x from 0 to 0.07 for Bi_1−x(La_0.38Nd_0.62)_xNbO₄ ceramics. The saturated Q×f value is between 10,300 and 12,400 GHz depending on the x value. The τ_f values of dense Bi_1−x(La_0.38Nd_0.62)_xNbO₄ ceramics decrease from 28.32 to 12.79 ppm/°C with x varying from 0 to 0.01 and remain almost unchanged with further increasing x.     

Low temperature sintering and microwave dielectric properties of ZnTiNb2O8 ceramics with BaCu(B2O5) additions

The phases, microstructure and microwave dielectric properties of ZnTiNb₂O₈ ceramics with BaCu(B₂O₅) additions prepared by solid-state reaction method have been investigated using X-ray diffraction (XRD) and scanning electron microscopy (SEM). The pure ZnTiNb₂O₈ ceramic shows a high sintering temperature of about 1250 °C. However, it was found that the addition of BaCu(B₂O₅) lowered the sintering temperature of ZnTiNb₂O₈ ceramics from above 1250 °C to 950 °C due to the BCB liquid-phase. The results showed that the microwave dielectric properties were strongly dependent on densification, crystalline phases and grain size. Addition of 3 wt% BCB in ZnTiNb₂O₈ ceramics sintered at 950 °C afforded excellent dielectric properties of ?_r = 32.56, Q × f = 20,100 GHz (f = 5.128 GHz) and τ_f = −64.87 ppm/°C. These represent very promising candidates for LTCC dielectric materials.     

Microstructure and microwave dielectric characteristics of (1 − x)Ba(Zn1/3Ta2/3)O3-xBaTi4O9 ceramics

(1 − x)Ba(Zn_1/3Ta_2/3)O₃-xBaTi₄O₉ (0.1 ≤ x ≤ 0.85) composites are prepared by mixing 1150 °C-calcined BaTi₄O₉ with 1150 °C-calcined Ba(Zn_1/3Ta_2/3)O₃ powders. The crystal structure, microwave dielectric properties and sinterabilites of the (1 − x)Ba(Zn_1/3Ta_2/3)O₃-xBaTi₄O₉ ceramics have been investigated. X-ray diffraction patterns reveal that BaTi₄O₉, ordered and disordered Ba(Zn_1/3Ta_2/3)O₃ phases exist independently over the whole compositional range. The sintering temperatures of (1 − x)Ba(Zn_1/3Ta_2/3)O₃-xBaTi₄O₉ ceramics are about 1240 - 1320 °C and obviously lower than those of Ba(Zn_1/3Ta_2/3)O₃ ceramics. The dielectric constants (?_r) and the temperature coefficient of resonant frequency (τ_f) of (1 − x)Ba(Zn_1/3Ta_2/3)O₃-xBaTi₄O₉ ceramics increase with the increase of BaTi₄O₉ content. Nevertheless, the bulk densities and the quality values (Q × f) of (1 − x)Ba(Zn_1/3Ta_2/3)O₃-xBaTi₄O₉ ceramics increase with the increase of Ba(Zn_1/3Ta_2/3)O₃ content. The results are attributed to the higher density and quality value of Ba(Zn_1/3Ta_2/3)O₃ ceramics, the better grain growth, and the densification of sintered specimens added a small BaTi₄O₉ content. The (1 − x)Ba(Zn_1/3Ta_2/3)O₃-xBaTi₄O₉ ceramic with x = 0.1 sintered at 1320 °C exhibits a ?_r value of 31.5, a maximum Q × f value of 68500 GHz and a minimum τ_f value of 4.1 ppm/°C.     

Modified tunable dielectric properties by addition of MgO on BaZr0.25Ti0.75O3 ceramics

Phase composition, microstructure and tunable dielectric properties of (1 − x)BaZr_0.25Ti_0.75O₃-xMgO (BZTM) composite ceramics fabricated by solid-state reaction were investigated. It was found Mg not only existed in the matrix as MgO, there was also trace amount of Mg²⁺ ions dissolved in the BZT grains, which led to Curie temperature of the BZTM composites ceramics shifting to below −100 °C. Dielectric permittivity of the BZTM composite ceramics was reduced from thousands to hundreds by manipulating the content of MgO. Johnson's phenomenological equation based on Devonshire's theory was used to describe the nonlinear dielectric permittivity of the ceramics with increasing applied DC field. With increasing content of MgO, anharmonic constant α_(T) increased monotonously. Dielectric permittivity was 672, while dielectric tunability was as high as 30.0% at 30 kV/cm and dielectric loss was around 0.0016 for the 0.6BaZr_0.25Ti_0.75O₃-0.4MgO sample at 10 kHz and room temperature.