Catalytic Performance of Pt/ZrO2 and Pt/Ce-ZrO2 Catalysts on CO2 Reforming of CH4 Coupled with Steam Reforming or Under High Pressure

CO₂ reforming of methane was performed on Pt/ZrO₂ and Pt/Ce-ZrO₂ catalysts at 1073K under different reactions conditions: (i) atmospheric pressure and CH₄:CO₂ ratio of 1:1 and 2:1; (ii) in the presence of water and CH₄:CO₂ ratio of 2:1; (iii) under pressure (105 and 190 psig) and CH₄:CO₂ ratio of 2:1. The Pt supported on ceria-promoted ZrO₂ catalyst was more stable than the Pt/ZrO₂ catalyst under all reaction conditions. We ascribe this higher stability to the higher density of oxygen vacancies on the promoted support, which favors the cleaning mechanism of the metal particle. The increase of either the CH₄:CO₂ ratio or total pressure causes a decrease in activity for both catalysts, because under either case the rate of methane decomposition becomes higher than the rate of oxygen transfer. The Pt/Ce-ZrO₂ catalyst was always more stable than the Pt/ZrO₂ catalyst, demonstrating the important role of the support on this reaction.     

Catalytic syngas production from greenhouse gasses: Performance comparison of Ru-Al2O3 and Rh-CeO2 catalysts

In this work, 3% Ru-Al₂O₃ and 2% Rh-CeO₂ catalysts were synthesized and tested for CH₄-CO₂ reforming activity using either CO₂-rich or CO₂-lean model biogas feed. Low carbon deposition was observed on both catalysts, which negligibly influenced catalytic activity. Catalyst deactivation during temperature programmed reaction was observed only with Ru-Al₂O₃, which was caused by metallic cluster sintering. Both catalysts exhibited good stability during the 70 h exposure to undiluted equimolar CH₄/CO₂ gas stream at 750 °C. By varying residence time in the reactor during CH₄-CO₂ reforming, very similar quantities of H₂ were consumed for water formation. Reverse water-gas shift (RWGS) reaction occurred to a very similar extent either with low or high WHSV values over both catalysts, revealing that product gas mixture contained near RWGS equilibrium composition, confirming the dominance of WGS reaction and showing that shortening the contact time would actually decrease the H₂/CO ratio in the syngas produced by CH₄-CO₂ reforming, as long as RWGS is quasi equilibrated. H₂/CO molar ratio in the produced syngas can be increased either by operating at higher temperatures, or by using a feed stream with CH₄/CO₂ ratio well above 1.     

Improved resistance against coke deposition of titania supported cobalt and nickel bimetallic catalysts for carbon dioxide reforming of methane

The catalytic behavior of bi-metallic Co–Ni/TiO₂ catalysts for CO₂ reforming of CH₄ to synthesis gas was investigated under atmospheric pressure with a particular attention to carbon deposition. The catalysts with optimized Co/Ni ratios showed high catalytic stability towards the reaction with very little amount of deposited carbon at a wide range of reaction temperature (773–1123 K). The results suggest that adjusting of composition of the active metals (Co and Ni) can kinetically control the elementary steps (formation of carbon species and its removal by oxygen species) of CH₄/CO₂ reaction.     

Role of support in reforming of CH4 with CO2 over Rh catalysts

The reforming of CH₄ with CO₂ over supported Rh catalysts has been studied over a range of temperatures (550–1000 K). A significant effect of the support on the catalytic activity was observed, where the order was Rh/Al₂O₃>Rh/TiO₂>Rh/SiO₂. The catalytic activity of Rh/SiO₂ was promoted markedly by physical mixing of Rh/SiO₂ with metal oxides such as Al₂O₃, TiO₂, and MgO, indicating a synergetic effect. The role of the metal oxides used as the support and the physical mixture may be ascribed to the promotion in dissociation of CO₂ on the surface of Rh, since the CH₄ + CO₂ reaction is first order in the pressure of CO₂, suggesting that CO₂ dissociation is the rate-determining step. The possible model of the synergetic effect was proposed.     

Catalytic reaction of CH4 with CO2 over alumina-supported Pt metals

The dissociation of CH₄ and CO₂, as well as the reaction between CH₄ and CO₂ at 723–823 K have been studied over alumina supported Pt metals. In the high temperature interaction of CH₄ with catalyst surface small amounts of C₂H₆ were detected. In the reaction of CH₄+CO₂, CO and H₂ were produced with different ratios. The specific activities of the catalysts decreased in the order: Ru, Pd, Rh, Pt and Ir, which agreed with their activity order towards the dissociation of CO₂.This laboratory is a part of the Center for Catalysis, Surface and Material Science at the University of Szeged.     

Selective methanation of CO over supported Ru catalysts

The catalytic performance of supported ruthenium catalysts for the selective methanation of CO in the presence of excess CO₂ has been investigated with respect to the loading (0.5–5.0 wt.%) and mean crystallite size (1.3–13.6 nm) of the metallic phase as well as with respect to the nature of the support (Al₂O₃, TiO₂, YSZ, CeO₂ and SiO₂). Experiments were conducted in the temperature range of 170–470 °C using a feed composition consisting of 1%CO, 50% H₂ 15% CO₂ and 0–30% H₂O (balance He). It has been found that, for all catalysts investigated, conversion of CO₂ is completely suppressed until conversion of CO reaches its maximum value. Selectivity toward methane, which is typically higher than 70%, increases with increasing temperature and becomes 100% when the CO₂ methanation reaction is initiated. Increasing metal loading results in a significant shift of the CO conversion curve toward lower temperatures, where the undesired reverse water–gas shift reaction becomes less significant. Results of kinetic measurements show that CO/CO₂ hydrogenation reactions over Ru catalysts are structure sensitive, i.e., the reaction rate per surface metal atom (turnover frequency, TOF) depends on metal crystallite size. In particular, for Ru/TiO₂ catalysts, TOFs of both CO (at 215 °C) and CO₂ (at 330 °C) increase by a factor of 40 and 25, respectively, with increasing mean crystallite size of Ru from 2.1 to 4.5 nm, which is accompanied by an increase of selectivity to methane. Qualitatively similar results were obtained from Ru catalysts supported on Al₂O₃. Experiments conducted with the use of Ru catalyst of the same metal loading (5 wt.%) and comparable crystallite size show that the nature of the metal oxide support affects significantly catalytic performance. In particular, the turnover frequency of CO is 1–2 orders of magnitude higher when Ru is supported on TiO₂, compared to YSZ or SiO₂, whereas CeO₂- and Al₂O₃-supported catalysts exhibit intermediate performance. Optimal results were obtained over the 5%Ru/TiO₂ catalyst, which is able to completely and selectively convert CO at temperatures around 230 °C. Addition of water vapor in the feed does not affect CO hydrogenation but shifts the CO₂ conversion curve toward higher temperatures, thereby further improving the performance of this catalyst for the title reaction. In addition, long-term stability tests conducted under realistic reaction conditions show that the 5%Ru/TiO₂ catalyst is very stable and, therefore, is a promising candidate for use in the selective methanation of CO for fuel cell applications.     

Improvement of Pt/ZrO2 by CeO2 for high pressure CH4/CO2 reforming

CH₄/CO₂ reforming over Pt/ZrO₂, Pt/CeO₂ and Pt/ZrO₂ with CeO₂ was investigated at 2 MPa. Pt/ZrO₂, which shows stable activity under 0.1 MPa, and Pt/CeO₂ showed gradual deactivation with time at the high pressure. The deactivation was suppressed drastically on Pt/ZrO₂ with CeO₂ prepared by different impregnation order (co-impregnation of Pt and CeO₂ on ZrO₂, and consecutive impregnation of Pt and CeO₂ on ZrO₂). The amount of coke deposition was found insignificant and similar among all the catalysts (including Pt/ZrO₂ and Pt/CeO₂). Catalytic activity after the reaction for 24 h was in agreement with Pt particle size after the reaction for same period, indicating that the difference of the catalytic stability is mainly dependent on the extent of Pt aggregation through catalyst preparation, H₂ reduction, and the CH₄/CO₂ reforming. Pt aggregation and the amount of coke deposition were least pronounced on (Pt–Ce)/ZrO₂ prepared by impregnation of CeO₂ on Pt/ZrO₂ and the catalyst showed highest stability.     

Suppression of carbon deposition in CO2-reforming of methane on metal sulfide catalysts

The catalytic performance of metal sulfides of Mo and W was studied for the CO₂-reforming of methane by comparing with that of Ni/SiO₂. The sulfide catalysts have lower activity than the Ni/SiO₂ catalyst for this reaction, however, no deactivation due to carbon deposition was observed on the sulfide catalysts. The activity for direct decomposition of CH₄ was much smaller on the sulfides than on supported Ni. The rate equation suggested that, during steady-state reaction, the surface was abundant in adsorbed CO₂ on sulfides, by which direct decomposition of CH₄ should be retarded in addition to their lower activity for this reaction.     

Influence of the oxygen pretreatment on the CO2 reforming of methane on Ni/β-SiC catalyst

The influence of the O₂ pretreatment on the CO₂ reforming of methane to synthesis gas has been investigated with Ni catalysts supported on β-SiC extrudate. The structure and properties of the catalysts were characterised by SEM, TEM and XRD techniques. The pretreatment of the catalyst by a mixture of CO₂ and O₂ significantly improves the catalytic activity for the CO₂ reforming. On the Ni 5 wt.% supported on β-SiC catalyst, the CH₄ conversion has reached 90% with the O₂ pretreatment instead of 80% by direct activation under CO₂/CH₄ mixture. The oxygen pretreatment seems to stabilize the metallic nickel phase instead of NiSi₂.     

Improvement of coke resistance of Ni/Al2O3 catalyst in CH4/CO2 reforming by ZrO2 addition

This work investigates the improvement of Ni/Al₂O₃ catalyst stability by ZrO₂ addition for H₂ gas production from CH₄/CO₂ reforming reactions. The initial effect of Ni addition was followed by the effect of increasing operating temperature to 500–700 °C as well as the effect of ZrO₂ loading and the promoted catalyst preparation methods by using a feed gas mixture at a CH₄:CO₂ ratio of 1:1.25. The experimental results showed that a high reaction temperature of 700 °C was favored by an endothermic dry reforming reaction. In this reaction the deactivation of Ni/Al₂O₃ was mainly due to coke deposition. This deactivation was evidently inhibited by ZrO₂, as it enhances dissociation of CO₂ forming oxygen intermediates near the contact between ZrO₂ and nickel where the deposited coke is gasified afterwards. The texture of the catalyst or BET surface area was affected by the catalyst preparation method. The change of the catalyst texture resulted from the formation of ZrO₂–Al₂O₃ composite and the plugging of Al₂O₃ pore by ZrO₂. The 15% Ni/10% ZrO₂/Al₂O₃ co-impregnated catalyst showed a higher BET surface area and catalytic activity than the sequentially impregnated catalyst whereas coke inhibition capability of the promoted catalysts prepared by either method was comparable. Further study on long-term catalyst stability should be made.     

Activity of different zeolite-supported Ni catalysts for methane reforming with carbon dioxide

The catalytic performance of Ni based on various types of zeolites (zeolite A, zeolite X, zeolite Y, and ZSM-5) prepared by incipient wetness impregnation has been investigated for the catalytic carbon dioxide reforming of methane into synthesis gas at 700 °C, at atmospheric pressure, and at a CH₄/CO₂ ratio of 1. It was found that Ni/zeolite Y showed better catalytic performance than the other types of studied zeolites. In addition, the stability of the Ni/zeolite Y was greatly superior to that of the other catalysts. A weight of Ni loading at 7 wt.% showed the best catalytic activity on each zeolite support; however, the 7% Ni catalysts produced a higher amount of coke than that of two other Ni loadings, 3 and 5%.     

Raney Ni catalysts derived from different alloy precursors Part II. CO and CO2 methanation activity

Catalytic activity, in conjunction with reaction mechanism, was studied in the methanation of CO and CO₂ on three Raney Ni catalysts derived from different Ni-Al alloys using different leaching conditions. Main products were CH₄ and CO₂ in CO methanation, and CH₄ and CO in CO₂ methanation. Any other hydrocarbon products were not observed. Over all catalysts, CO methanation showed lower selectivity to methane and higher activation energy than CO₂ methanation. The catalyst derived from alloy having higher Ni content using more severe leaching conditions, namely higher reaction temperature and longer extraction time, showed higher specific activity and higher selectivity to methane both in CO and CO₂ methanation. In CO and CO₂ methanation on Raney Ni catalyst, catalytic activity was seen to have close relation with the activity to dissociate CO This paper was presented at the 2004 Korea/Japan/Taiwan Chemical Engineering Conference held at Busan, Korea between November 3 and 4,2004.     

Sequential production of H2 and CO over supported Ni catalysts

Methane decomposition into H₂ and carbon nanofibers at 823 K and subsequent gasification of the carbon nanofibers with CO₂ into CO at 923 K were performed over supported Ni catalysts (Ni/SiO₂, Ni/TiO₂ and Ni/Al₂O₃). Supported Ni catalysts were deactivated for CH₄ decomposition with time on stream due to deposition of a large amount of carbon nanofibers. Subsequent contact of CO₂ with carbon nanofibers on the deactivated catalysts resulted in the formation of CO with a conversion of the carbons higher than 95%. In addition, gasification with CO₂ regenerated the activity of supported Ni catalysts for CH₄ decomposition, indicating that H₂ formation through CH₄ decomposition and CO formation through gasification with CO₂ could be carried out repeatedly. Conversions of carbon nanofibers into CO were kept higher than 95% in the repeated gasification over all the catalysts, while change in the catalytic activity for CH₄ decomposition with the repeated cycles depended on the kind of catalytic supports. Catalytic activity of Ni/SiO₂ for CH₄ decomposition was high at early cycles, however, the activity decreased gradually with the repeated cycles. On the other hand, Ni/TiO₂ and Ni/Al₂O₃ showed high activity for CH₄ decomposition and the activity was kept high during the repeated cycles. These changes of catalytic activities for CH₄ decomposition could be explained by changes in particle sizes of Ni metal, i.e. Ni metal particles in Ni/SiO₂ aggregated into ones larger than 150 nm with the repeated cycles, while the particle sizes of Ni metal in Ni/TiO₂ and Ni/Al₂O₃ remained at an effective range for CH₄ decomposition (60-100 nm).     

CH4/CD4 isotope effects in the carbon dioxide reforming of methane to syngas over SiO2-supported nickel catalysts

By performing the CH₄ + CO₂ and CD₄ + CO₂ reactions alternately over SiO₂-supported nickel catalysts in a pulse micro-reactor, normal deuterium isotope effects on both the methane conversion reaction and on the CO formation reaction have been observed in the process of CO₂ reforming of methane. Based on the observed CH₄/CD₄ isotope effects, the pathways for the formation of CO are discussed.     

Characteristics of adsorbed CO and CH3OH oxidation reactions for complex Pt/Ru catalyst systems

Pt/Ru powder catalysts of the same nominal Pt to Ru composition were prepared using a range of methods resulting in different catalyst properties. Two PtRu alloy catalysts were prepared, one of which has essentially the same surface and bulk Pt to Ru composition, while the second catalyst is surface enriched with Ru. Two powders consisting of non-alloyed Pt phases and surfaces enriched with Ru were also prepared. The oxidation state of the surface Ru of the latter two catalysts is mainly metallic Ru or Ru-oxides. The catalyst consisting of Ru-oxides was formed at 500 °C. Part of this catalyst was then reduced in a H₂ atmosphere under “mild” conditions, thus catalyst properties such as particle size are not changed, as they are locked in during previous high temperature treatment. The oxidation kinetics of adsorbed CO (CO_ads) and solution CH₃OH were studied and compared to the Ru ad-metal state and Pt to Ru site distribution of the as-prepared catalysts. The kinetics of the CO_ads oxidation reaction were observed to be slower for the catalyst containing Ru-oxides as opposed to mainly Ru metal. The CH₃OH oxidation activities measured per Pt surface area, i.e., the catalytic activities are better (by ca. seven times) for the alloy catalysts than the non-alloyed Pt/Ru catalysts. The latter two catalysts showed essentially the same catalytic CH₃OH oxidation activities, i.e., independent of the Ru ad-metal oxidation state of the as-prepared catalysts. Furthermore, it is shown that CO_ads oxidation experiments can be used to extract characteristics that allow the comparison of catalytic activities for the CO_ads oxidation reaction and Pt to Ru site distribution for complex catalyst systems.     

Carbon dioxide hydrogenation over nickel-, ruthenium-, and copper-based catalysts: Review of kinetics and mechanism

This study critically reviews the mechanism of CO₂ hydrogenation over Ni, Ru, and Cu, and the effect of catalyst properties and operating conditions on reaction kinetics. Most studies have reported the presence of CO and formate species on Ni-, Ru-, and Cu-based catalysts, where subsequent conversion of these species depends on the type of catalyst and the physicochemical properties of the catalyst support. Methane is the major product that forms during CO₂ hydrogenation over Ni and Ru catalysts, while methanol and CO are mainly produced on Cu catalysts. A different approach for catalyst formulations and/or process development is required where long chain hydrocarbons are desired.     

Effect of H2S on the hydrogenation of carbon dioxide over supported Rh catalysts

The hydrogenation of CO₂ was studied on supported noble metal catalysts in the presence of H₂S. In the reaction gas mixture containing 22 ppm H₂S the reaction rate increased on TiO₂ and on CeO₂ supported metals (Ru, Rh, Pd), but on all other supported catalysts or when the H₂S content was higher (116 ppm) the reaction was poisoned. FTIR measurements revealed that in the surface interaction of H₂ + CO₂ on Rh/TiO₂ Rh carbonyl hydride, surface formate, carbonates and surface formyl were formed. On the H₂S pretreated catalyst surface formyl species were missing. TPD measurements showed that adsorbed H₂S desorbed as SO₂, both from TiO₂-supported metals and from the support. IR, XP spectroscopy and TPD measurements demonstrated that the metal became apparently more positive when the catalysts were treated with H₂S and when the sulfur was built into the support. The promotion effect of H₂S was explained by the formation of new centers at the metal/support interface.     

CO2 reforming of methane over vanadia-promoted Rh/SiO2 catalysts

The reforming of methane with carbon dioxide over rhodium dispersed on silica, Rh/SiO₂, and vanadia-promoted silica, Rh/VO_x/SiO₂, was studied by kinetic test reactions under differential conditions in a temperature range from 723 to 773 K. Transmission infrared spectroscopy was applied to observe the interaction of CO₂ with the catalysts and the formation of surface intermediates during the CO₂–CH₄ reforming reaction. To analyze carbon deposition XP spectroscopy and TPO was carried out. It has been shown that the promotion of Rh/SiO₂ catalysts with vanadium oxide enhances the catalytic activity for CO₂ reforming of methane and decreases the deactivation by carbon deposition. This is attributed to the formation of a partial VO_x overlayer on the Rh surface, which reduces the size of accessible ensembles of Rh atoms required for coke formation and creates new sites at the Rh–VO_x interfacial region that are considered to be active sites for the activation/dissociation of carbon dioxide. This revised version was published online in June 2006 with corrections to the Cover Date.     

Development of Ni-Pd bimetallic catalysts for the utilization of carbon dioxide and methane by dry reforming

The present research deals with catalyst development for the utilization of CO₂ in dry reforming of methane with the aim of reaching highest yield of the main product synthesis gas (CO, H₂) at lowest possible temperatures. Therefore, Ni-Pd bimetallic supported catalysts were prepared by simple impregnation method using various carriers. The catalytic performance of the catalysts was investigated at 500, 600 and 700 °C under atmospheric pressure and a CH₄ to CO₂ feed ratio of 1. Fresh, spent and regenerated catalysts were characterized by N₂ adsorption for BET surface area determination, XRD, ICP, XPS and TEM. The catalytic activity of the studied Ni-Pd catalysts depends strongly on the support used and decreases in the following ranking: ZrO₂-La₂O₃, La₂O₃ > ZrO₂ > SiO₂ > Al₂O₃ > TiO₂. The bimetallic catalysts were more active than catalysts containing Ni or Pd alone. A Ni to Pd ratio = 4 at a metal loading of 7.5 wt% revealed the best results. Higher loading lead to increased formation of coke; partly in shape of carbon nanotubes (CNT) as identified by TEM. Furthermore, the effect of different calcination temperatures was studied; 600 °C was found to be most favorable. No effect on the catalytic activity was observed if a fresh catalyst was pre-reduced in H₂ prior to use or spent samples were regenerated by air treatment. Ni and Pd metal species are the active components under reaction conditions. Best conversions of CO₂ of 78% and CH₄ of 73% were obtained using a 7.5 wt% NiPd (80:20) ZrO₂-La₂O₃ supported catalyst at a reaction temperature of 700 °C. CO and H₂ yields of 57% and 59%, respectively, were obtained.     

Cu-K/Al2O3 based catalysts for conversion of carbon dioxide to methane and carbon monoxide

Abstract

A series of Cu-K/Al₂O₃ catalysts were synthesized by wet impregnation technique. The reduced catalysts were further used for conversion of carbon dioxide to methane and carbon monoxide. Moreover, the fresh and used catalysts were characterized to investigate the changes in the surface morphology, metal dispersion, surface area, crystalline phases, and functional groups of studied catalysts. The SEM analysis of fresh and spent catalysts showed no remarkable difference in surface morphology with irregular shaped agglomerated particles. Furthermore, TEM micrographs presented the well distribution of metal catalyst over alumina support. The decrease in surface area from 115 to 77?m²/g for Cu_1.62-K_0.5/Al₂O₃ after reaction was related to sintering and oxidation of catalyst during reaction. XRD revealed the disappearance of some minor peaks which can be associated with the sintering of spent catalyst. FTIR also presented some new peak for spent catalyst which can be linked with metal oxides. Moreover, various reaction conditions of temperature (230, 400, and 600?°C), pressure (1 and 7?bar), and feed molar ratio of H₂/CO₂ (2:1 and 4:1) were investigated using different Cu loading (0, 1, 1.25, 1.62, and 4 weight percent). A maximum CO₂ conversion of 63% with 39% CH₄ selectivity was achieved by using Cu_1.62-K_0.5/Al₂O₃ at 600?°C, molar ratio of H₂/CO₂ 4 under 7?bar. The presence of K on the surface of synthesized catalyst increased the CO₂ conversion from 48% (Cu₁/Al₂O₃) to 55% (Cu₁-K_0.5/Al₂O₃) at above mentioned reaction conditions which suggested the promoter effect of K during conversion of carbon dioxide.