Self-assembly hydrothermal assisted synthesis of mesoporous anatase in the presence of ethylene glycol

Mesoporous nanocrystalline anatase was prepared hydrothermally employing P123 as structure-directing agent. Ethylene glycol was used as a key synthesis parameter to fine tune the morphology, crystal size and pore size of the resultant mesophases. The incorporation of EG in the synthesis gel resulted in the formation of 1–2 μm sphere-like shapes and led to an increase in the specific surface area from 95 to 170 m²/g, decrease in the average pore size from 11 to 4.8 nm, and decrease in the average crystallite size from 17 to 12 nm. These mesophases were used as photocatalysts for the UV degradation of methylene blue and methyl orange. The mesoporous anatase phases photodegraded MB 1.5–3× faster than commercially available P25 and showed limited photocatalytic behavior for methyl orange.     

Use of different mesostructured materials based on silica as cobalt supports for the Fischer–Tropsch synthesis

To obtain a novel, active and selective to diesel catalytic material for syngas processing via Fischer–Tropsch synthesis (FTS), a series of 20 wt.% cobalt catalysts has been prepared by impregnation of a mesoporous molecular sieve based on silica (SBA-15, Al-MCM-41, INT-MM1), and a commercial amorphous silica for comparison purposes. All materials were characterized by several physico-chemical techniques: AAS, BET surface area, XRD, TPR, and H₂ chemisorption with pulse reoxidation and finally their reactivity on the FTS reaction was evaluated at 523 K, 10 bar, and H₂/CO = 2. Catalytic and characterization results show a great influence of mesoporous support porosity on the structure, reducibility, and FTS catalytic behavior of cobalt oxide species supported over these ordered materials. It was found that the size of supported cobalt oxide species formed during the calcination step increased with the average pore size (D_p) of the mesoporous support. Thus, the catalyst with larger Co oxide species located in wide pore silica showed to be easily reducible, more active and very selective toward the diesel fraction. It seems to be the case of the Co/SBA-15 solid, which showed to be the most active solid (XCO 63%) when the same mass of catalyst was used. Under CO iso-conversion conditions (XCO 40%), Co/SBA-15 was more selective toward the formation of C₅₊ hydrocarbons (80%, α = 0.76) and less selective to CH₄ (15%). On the contrary, when Al-MCM-41 and INT-MM1 were used as supports, a lower selectivity to C₅₊ and CO conversion and higher CH₄ selectivity (20%) were observed due to the decrease of D_p, of the cobalt oxide species size and the reducibility degree of such species.     

Hierarchical porous silica membranes with dispersed Pt nanoparticles

Multifunctional silica membranes with a hierarchical porosity and containing dispersed Pt nanoparticles were prepared by an original one pot microwave-assisted sol–gel route. These membranes exhibit three porosity levels: interconnected micropores (<2 nm) in silica walls, isolated ordered mesopores (4 nm), and isolated macropores (70 nm). They were directly coated on tubular macroporous alumina supports without any intermediate mesoporous layer contrary to conventional membrane architectures. The isolated macropores and mesopores enable to increase the membrane permeability whereas the interconnected microporosity defines the membrane cut-off. The catalytic Pt nanoparticles (4 nm) mainly hosted in the mesoporous volume, are stabilised against undesirable agglomeration under working conditions. A first series of multifunctional membranes were prepared, in which preferential adsorption of hydrocarbon gases and efficient propene oxidation were evidenced. In order to avoid any possible interconnection between macropores, several strategies were investigated, which prevented sol infiltration in the macroporous support during the deposition process. These original multifunctional membranes are potentially attractive for gas separation and catalytic reactor applications.     

Near-ambient X-ray photoemission spectroscopy and kinetic approach to the mechanism of carbon monoxide oxidation over lanthanum substituted cobaltites

We have studied the oxidation of carbon monoxide over a lanthanum substituted perovskite (La_0.5Sr_0.5CoO_3−d) catalyst prepared by spray pyrolysis. Under the assumption of a first-order kinetics mechanism for CO, it has been found that the activation energy barrier of the reaction changes from 80 to 40 kJ mol⁻¹ at a threshold temperature of ca. 320 °C. In situ XPS near-ambient pressure (0.2 torr) shows that the gas phase oxygen concentration over the sample decreases sharply at ca. 300 °C. These two observations suggest that the oxidation of CO undergoes a change of mechanism at temperatures higher than 300 °C.     

Preparation of TiO2 nanofilm via sol–gel process and its photocatalytic activity for degradation of methyl orange

The preparation of TiO₂ nanofilm was conducted on common glass via the sol–gel process. Glacial acetic acid and diethanolamine were used as inhibitors to prepare acidic and alkaline TiO₂ sol, respectively. XRD, SEM, and EDS characterization showed that the film prepared from acidic TiO₂ sol had a narrow particle size distribution of 15–30 nm and relatively poor particle crystallization while in the case of the film from alkaline TiO₂ sol the nanoparticles were in a wide range of 10–80 nm and well crystallized. The photolysis evaluation through MO degradation revealed that the film from acidic sol possessed apparently better photocatalytic activity than that from alkaline sol. Heat treatment with longer time led to a 50% increase of the photocatalytic activity for the film.     

A quantitative electron-microscopic investigation of α-phase lamellae in isotactic polypropylene fractions

Lamellar thicknesses and cross-hatching frequencies in α-isotactic polypropylene have been measured for two series of fractions using linear nucleation to provide large arrays of oriented lamellae in row structures for sampling. One series is of high tacticity polymers differing in molecular mass from 6 × 10⁴ to 8 × 10⁵, the other has low and high tacticity materials for 9 × 10⁴ and 2 × 10⁵ masses. These have allowed the differing influences of both molecular mass and tacticity to be evaluated. Lamellar thicknesses increase with molecular mass to 5 × 10⁵ then level off. This is consistent with the fold surface increasing its free energy by 20% for longer molecules as its structure becomes progressively more complex. Except for the lowest fraction, the thickness of cross-hatching lamellae is less than that of its radial neighbours because of differential thickening. The frequency of cross-hatching is greatest for the least tactic fraction but decreases linearly with molecular length. This dependence suggests that chain ends play a key role in initiation probably by laying down the first segment in epitaxial orientation. This suggestion could also account for the reduced thermal stability of spherulite centres and regions of high cross-hatching density where there is competition for chain ends between thickening and cross-hatching. The curvature of lamellae at the very end of a row mirrors the dependence of lamellae thickness with molecular mass and allows cilia pressure, the factor strongly involved in causing the lamellar divergence underlying spherulitic growth, to be estimated as 100 Pa.     

Thermal activation and alkali dissolution of silicon from illite

TGA, DTA, FTIR, XRD and 29Si MAS NMR were used to investigate the thermal activation of illite. Illite experiences a series of thermal solid-state phase transformations. Dehydroxylation at 400700 °C forms dehydrated illite, which remains the layered framework of illite. From 700 °C to 1093 °C, Si–O tetrahedral framework remains unchanged. When heated above 1093 °C, the layered structure is destroyed and an amorphous silica-rich glass phase is formed. The mullitization occurs when the temperature exceeds 1100 °C.XRD and FTIR studies show that the silica in silica-rich glass phase dissolves in soda liquor, which indicates that silicon can be removed from illite after thermochemical activation (TCA) followed by alkali leaching. The formation of sodium aluminosilicates of Na₉₆Al₉₆Si₉₆O₃₈₄ and 0.95Na₂O · Al₂O₃ · 3.25SiO₂ · 4.79H₂O during alkali leaching may reduce the desilication to a great extent.Desilication tests after TCA show that the suitable activation conditions for illite are 11001150°C and 9060 min. A desilication of 45% was obtained under the conditions for an ore sample bearing about 85% illite, 9% quartz and 5% muscovite.     

Surface charge heterogeneity of kaolinite in aqueous suspension in comparison with montmorillonite

An analogous study to 2:1 type montmorillonite [Tombácz, E., Szekeres, M., 2004. Colloidal behavior of aqueous montmorillonite suspensions: the specific role of pH in the presence of indifferent electrolytes. Appl. Clay Sci. 27, 75–94.] was performed on 1:1 type kaolinite obtained from Zettlitz kaolin. Clay minerals are built up from silica tetrahedral (T) and alumina octahedral (O) layers. These lamellar particles have patch-wise surface heterogeneity, since different sites are localized on definite parts of particle surface. pH-dependent charges develop on the surface hydroxyls mainly at edges besides the permanent negative charges on silica basal plane due to isomorphic substitutions. Electric double layers (edl) with either constant charge density on T faces (silica basal planes) or constant potential at constant pH on edges and O faces (hydroxyl-terminated planes) form on patches. The local electrostatic field is determined by the crystal structure of clay particles, and influenced by the pH and dissolved electrolytes. The acid–base titration of Na-kaolinite suspensions showed analogous feature to montmorillonite. The initial pH of suspensions and the net proton surface excess vs. pH functions shifted to the lower pH with increasing ionic strength indicating the presence of permanent charges in both cases, but these shifts were smaller for kaolinite in accordance with its much lower layer charge density. The pH-dependent charge formation was similar, positive charges in the protonation reaction of (Si–O)Al–OH sites formed only at pHs below  6–6.5, considered as point of zero net proton charge (PZNPC) of kaolinite particles. So, oppositely charged surface parts on both clay particles are only below this pH, therefore patch-wise charge heterogeneity exists under acidic conditions. Electrophoretic mobility measurements, however, showed negative values for both clays over the whole range of pH showing the dominance of permanent charges, and only certain decrease in absolute values, much larger for kaolinite was observed with decreasing pH below pH  6. The charge heterogeneity was supported by the pH-dependent properties of dilute and dense clay suspensions with different NaCl concentrations. Huge aggregates were able to form only below pH  7 in kaolinite suspensions. Coagulation kinetics measurements at different pHs provided undisputable proofs for heterocoagulation of kaolinite particles. Similarly to montmorillonite, heterocoagulation at pH  4 occurs only above a threshold electrolyte concentration, which was much smaller, only  1 mmol l^− 1 NaCl for kaolinite, than that for montmorillonite due to the substantial difference in particle geometry. The electrolyte tolerance of both clay suspensions increased with increasing pH, pH  6–6.5 range was sensitive, and even a sudden change occurred above pH  6 in kaolinite. There was practically no difference in the critical coagulation concentration of kaolinite and montmorillonite (c.c.c. 100 mmol l^− 1 NaCl) measured in alkaline region, where homocoagulation of negatively charged lamellae takes place. Rheological measurements showed shear thinning flow character and small thixotropy of suspensions at and above pH  6.7 proving the existence of repulsive interaction between uniformly charged particles in 0.01 M NaCl for both clays. The appearance of antithixotropy, the sudden increase in yield values, and also the formation of viscoelastic systems only at and below pH  6 verify the network formation due to attraction between oppositely charged parts of kaolinite particles. Under similar conditions the montmorillonite gels were thixotropic with significant elastic response.     

Structure and properties of short fibre reinforced silica matrix composite foams

Glass (GFC) and silica (SFC) fibre reinforced silica matrix composite foams with 84–90% porosity content have been developed through slurry-based processing, involving random dispersion of 10 wt.% fibres with aspect ratios of >1000 in hydrophobized silica-based suspensions, and direct foaming for air entrapment. Fibre entanglement has not been found either in the suspensions or in the sintered composite foams. Microstructural and mercury porosimetry studies of the composite foams have shown a trimodal size distribution with small (4–8 μm), medium (40–200 μm), and large (1 mm or more) pores. The pores appear spherical and interconnected, with the fibres embedded in cell-walls or struts. The dynamic Young's modulus of the silica-coated GFCs is found to be 3.5 and 5.2 times that of the coated and uncoated monolithic silica foams, respectively, confirming that both fibre-reinforcement and the presence of surface coating are beneficial for increase in stiffness of the composite foams.     

A lithographic approach to determine volume expansion factors during anodization: Using the example of initiation and growth of TiO2-nanotubes

The present work investigates the formation of nanotubes by anodizing titanium at 20 V in glycerol containing either 0.175 M or 0.35 M NH₄F. A photoresist-masking method of thin Ti films allows to use SEM cross-sections to directly obtain information on oxide morphology, layer thickness and metal substrate loss. Therefore not only features of the initial growth stages but also oxide expansion factors can accurately be determined. The expansion factors were found to be 2.4 for the initial formation of a barrier layer, 1.7–1.9 during pore initiation and 2.7–3.1 as the main nanotubes develop. These values (>2.6) suggest substantial contribution to steady state tube growth by a plastic oxide flow mechanism. Combined with RBS efficiency measurements the method presented here allows facile and direct investigation of the mechanism of pore/tube formation.     

Synthesis and magnetic properties of nanoporous Co3O4 nanoflowers

Nanoporous Co₃O₄ hierarchical nanoflowers have been prepared through sequential process of a hydrothermal reaction and heat treatment. These nanoflowers consisting of a great deal of Co₃O₄ nanofibers have bimodal pore structures and Brunauer–Emmett–Teller surface area of 34.61 m²/g. The temperature dependence curves of magnetization in zero-field-cooled and field-cooled exhibit main antiferromagnet and weak ferromagnet of Co₃O₄ nanoflowers at blocking temperature of 34 K, respectively. In addition, analysis of their optic properties obviously indicates red shift of absorption peaks, exhibiting quantum-confined effect and traits of semiconductor.     

Highly bright and photostable cyanine dye-doped silica nanoparticles for optical imaging: Photophysical characterization and cell tests

Spherical silica nanoparticles containing fluorescent trimethine indocyanine dyes (λ_abs = 547 nm, λ_em = 570 nm) were prepared using a water-in-oil microemulsion method. The nanoparticles were of 50 nm diameter and were almost monodispersed in aqueous solution at pH 5.5. Entrapment of dye molecules in the silica matrix stabilised photoemission over several hours of continuous irradiation. The photoemission intensity of the indocyanine was increased 13-fold over that recorded in solution. As each nanoparticle contained 110 dye molecules, the photoemission brightness of each particle was enhanced by three orders of magnitude. The fluorescent nanoparticles have been tested as imaging tools in in vitro tests. As an example of non-macrophagic cells, a highly differentiated neuronal cell line (GT1-7) was used and the results showed that the prepared nanoparticles can be incorporated into these cells with no apparent toxicity for up to three days.     

Thermal and mechanical properties of LaNbO4-based ceramics

Thermal and mechanical properties of polycrystalline La_1−xA_xNbO₄ (x = 0, 0.005, 0.02 and A = Ca, Sr and Ba) are reported. The materials possess a ferroelastic to paraelastic phase transition close to 500 °C, and the linear thermal expansion is significantly lower (8.6 ± 0.5 × 10⁻⁶ °C⁻¹) for the paraelastic phase compared to the ferroelastic phase (15 ± 3 × 10⁻⁶ °C⁻¹). The hardness was significantly higher for acceptor doped materials (6 GPa) compared to pure LaNbO₄ (3 GPa) due to a significantly smaller average grain size. The fracture toughness of La_0.98Sr_0.02NbO₄, measured by single edge V-notched beam method, was 1.7 ± 0.2 MPa m^1/2 independent of temperature up to 600 °C. The ferroelastic properties of the materials were confirmed by non-linear relationships between stress and strain during compression/decompression, a remnant strain after decompression and the presence of ferroelastic domains. The mechanical properties of LaNbO₄-based materials are discussed with focus on ferroelasticity, microcracking due to crystallographic anisotropy and pinning of ferroelastic domain boundaries.     

Carbon nanotubes field emission integrated triode amplifier array

Because the high frequency operation of a field emission triode amplifier is dictated by the cutoff frequency and not the electron transit time, a high ratio of transconductance, g_m to the overlapping interelectrode capacitance, C_g is the desired outcome. Consequently, to achieve high frequency performance of the CNT amplifier array in this study, C_g was reduced by performing a dual-mask photolithography process to minimize the overlapping gate area, and, the insulating layer's thickness was increased. Moreover, wedge-shaped CNT emitter arrays are employed to increase emission sites, resulting in return higher g_m. Both dc and ac performance of the amplifier were characterized. The triode amplifier array exhibited a high current of  0.32 mA (74 mA/cm²), g_m of  63 μS and voltage gain of  18 dB. Frequency response of the triode amplifier up to 20 kHz was also investigated. A theoretical cutoff frequency of > 70 MHz could be achieved with proper shielding of the test setup.     

A novel method for the recovery of 4,4′-dinitrostilbene-2,2′disulfonic acid from the wastewater obtained from 4,4′-diaminostilbene-2,2′-disulfonic acid production

HPLC and electrospray ionization tandem mass spectrometry were used to show that 30% of the DNS present in wastewater was reduced to 4-amino-4′-nitrostilbene-2,2′-disulfonic acid and 4,4′-diaminostilbene-2,2′-disulfonic acid during multiple-effect evaporation. A novel recovery method, which combines acidification and subsequent reduction, recovered of 90% of the DNS that is lost during evaporation and, thereby, increased the yield of 4,4′-diaminostilbene-2,2′-disulfonic acid by 5%. In addition, many of the organic compounds present in the wastewater were removed.     

Impact of supercritical drying and heat treatment on physical properties of titania/silica aerogel monolithic and its applications

TiO₂–SiO₂ monolithic aerogels were homogeneously prepared using sol–gel method. Critical point of drying of TiO₂–SiO₂ gels with ethanol was studied for 30, 60, 90 and 120 min. Subsequently, the gels were dried with supercritical ethanol, resulting in amorphous aerogels that crystallized following heat treatment at 550 °C from 1 to 5 h. The TiO₂–SiO₂ aerogels were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM) and surface area measurements. The molar ratio of SiO₂:TiO₂ was 6 and the synthetic strategy revealed that TiO₂–SiO₂ aerogel, had a surface area 868 m²/g, particle size 40 nm, density 0.17 g/cm³ and 80% porosity. The finding indicated that from economic point of view, TiO₂–SiO₂ gel should be supercritical dried for 30 min and heat-treated for 5 h. The TiO₂–SiO₂ aerogel monoliths photocatalyst synthesized using sol–gel method provided insight into the characteristics that make a photocatalyst material well-suited for photodegradation of phenol and cyanide in an industrial waste stream containing Cl⁻, S²⁻ and NH₄⁺. Interestingly, after multiple reuse cycles (i.e. ≥7), photodegradation systems with regenerated photocatalyst showed a slightly decreasing of photoactivity 2–4%. The overall kinetics of photodegradation of either phenol or cyanide using TiO₂–SiO₂ aerogel photocatalyst was found to be of first order.     

Ruthenium(IV) dioxide-catalyzed reductive gasification of intractable biomass including cellulose, heterocyclic compounds, and sludge in supercritical water

Catalytic reduction gasification in the presence of ruthenium(IV) dioxide (RuO₂) in supercritical water was used to decompose intractable biomass. The gasification of model biomass samples (glucose, cellulose, and heterocyclic compounds), and low-purity biomass samples obtained from a paper-recycling facility (paper sludge) and from a sewage treatment plant (sewage sludge) were studied. In clear contrast to another catalysts, the RuO₂ catalyst completely gasified cellulose to produce mainly hydrogen, methane, and carbon dioxide under various conditions (e.g., 673 K at 30 MPa and 773 K at 50 MPa). As for heterocyclic compounds, nitrogen compounds did not deactivate the RuO₂ catalyst; the gasification of carbazole proceeded completely. Furthermore, paper sludge was almost completely decomposed in supercritical water with RuO₂ at 723 K.     

Pre-nucleation techniques for enhancing nucleation density and adhesion of low temperature deposited ultra-nanocrystalline diamond

Effect of pre-nucleation techniques on enhancing nucleation density and the adhesion of ultra-nanocrystalline diamond (UNCD) deposited on the Si substrates at low temperature were investigated. Four different pre-nucleation techniques were used for depositing UNCD films: (i) bias-enhanced nucleation (BEN); (ii) pre-carburized and then ultrasonicated with diamond powder solution (PC-U); (iii) ultrasonicated with diamond and Ti mixed powder solution (U-m); (iv) ultrasonicated with diamond powder solution (U). The nucleation density is lowest for UNCD/U-substrate films ( 10⁸ grains/cm²), which results in roughest surface and poorest film-to-substrate adhesion. The UNCD/PC-U-substrate films show largest nucleation density ( 1 × 10¹¹ grains/cm²) and most smooth surface (8.81 nm-rms), whereas the UNCD/BEN-substrate films exhibit the strongest adhesion to the Si substrates (critical loads =  67 mN). Such a phenomenon can be ascribed to the high kinetic energy of the carbon species, which easily form covalent bonding, Si–C, and bond strongly to both the Si and diamond.     

Novel photochemical reaction of itaconatopentamminecobalt(III) ion to produce a room temperature luminescent compound

Irradiation of itaconatopentamminecobalt(III) perchlorate complex in the ligand to metal charge transfer absorption band in aqueous solution using 254 nm radiation produced an oxidised ligand free radical, which further reacts with itaconatopentamminecobalt(III) ion and also by radical dimerisation reaction to form a compound which shows broad absorption at 265 nm and emission at 425 nm. The compound is identified to be a derivative of itaconic acid. The photoproduct shows two lifetimes of 1.5±0.1 ns and 5.5±0.5 ns indicating that the photoproduct decomposes at room temperature to give a second compound which is also luminescent.     

Good temperature stability of K0.5Na0.5NbO3 based lead-free ceramics and their applications in buzzers

(K_0.5−xLi_x)Na_0.5(Nb_1−ySb_y)O₃ (KLNNSx–y, x = 0–4 mol% and y = 0–8 mol%) lead-free piezoelectric ceramics were prepared by the conventional mixed oxide method. The denser microstructure and better electrical properties of the ceramics were obtained as compared to the pure K_0.5Na_0.5NbO₃ ceramic. The temperature stability of the electrical properties of the ceramics was also investigated. The experimental results show that the KLNNS2.5–5 ceramic exhibits good electrical properties (k_p  49%, k₃₁  30% and , tan δ  0.019), and possesses good temperature stability in the temperature range of −40 to 85 °C. The related mechanisms for improved electrical properties and temperature stability were also discussed. Moreover, buzzers based on the KLNNS2.5–5 ceramic have been fabricated and their characterization is presented. These results show that the KLNNS2.5–5 ceramic is a promising lead-free material for practical application in buzzers.