Kinetic study of domestic limestone (Daesung)

Sulfidation and sulfation reactions of Daesung limestone, which is a calcium-based sorbent chosen out of domestic limestone for the removal of H₂S and SO₂, were investigated by using TGA (thermal gravimetric analyzer) Effects of H and H₂S on the sulfidation were also investigated The conversion rate of CaS to CaSO₄ in oxidation was low since the concentration of SO₂ used for this study was low and CaO was not completely converted into CaS It was observed that the effects of H₂ concentration on the sulfidation were relatively small and the maximum conversion rate and reaction rate increased with increase of H₂S concentration In the sulfation reaction, conversion rate could be raised with the injection of air at a sulfation reaction temperature above 800 °C However, the conversion rate decreased without the injection of air due to the blockage of sorbent pores.     

铬酸钡与硫酸氢钠制备重铬酸钠的宏观反应动力学

考察了BaCrO4与NaHSO4制备Na2Cr2O7过程中搅拌速率、氢离子初始浓度、反应温度对BaCrO4转化率的影响,在机理分析基础上进行了宏观动力学研究. 结果表明,该过程为BaCrO4溶于酸性水溶液生成BaCr2O7、BaCr2O7与NaHSO4反应生成BaSO4与Na2Cr2O7、BaSO4结晶析出三步,反应过程中应尽量升高反应温度,搅拌速率可固定为400 r/min,而氢离子浓度应大于0.01 mol/L且小于NaHSO4饱和时的浓度. 经过对实验数据处理和分析,建立了宏观动力学模型,得出该反应为一级反应,求得活化能为41.029 kJ/mol,频率因子为15978.51,相应的宏观动力学方程为-ln(1-XA)=15978.51exp[-41.029′103/(RT)]t.     

铜基低变催化剂H_2S中毒机理热力学分析

为掌握CO变换制氢过程中催化剂中毒机理,采用热力学非均相反应体系中G ibbs自由能最小原理,分析了铜基低温变换催化剂在463.15—523.15 K内H2S中毒过程中可能发生的化学反应及其产物,并结合文献实验结果综合讨论了铜基低温变换催化剂的H2S中毒机理。结果表明:催化剂的H2S中毒过程中,硫酸盐和积碳会造成催化剂的暂时性中毒,生成Cu2S和CuS化合物造成永久性中毒;O2的存在会加快催化剂的中毒反应;铜基低温变换催化剂不适合用于含高体积分数CO原料气的变换反应过程。     

T302锌锰系脱硫剂脱除H_2S在的宏观动力学

用热重法研究了T302锌锰系脱硫剂脱除H_2S的宏观动力学行为.实验表明,该过程对H_2S为一级反应.在200～400℃的温度范围,反应初期为表面反应控制,中后期转移为颗粒扩散控制.宏观动力学行为可用等效粒子模型来描述.表面反应及固体扩散活化能分别为11.842、20.865kJ/mol.对反应存在最佳温度及固体扩散活化能大于表面反应活化能进行了讨论.     

The random pore model with intraparticle diffusion for the description of combustion of char particles derived from mineral- and inertinite rich coal

An investigation was undertaken to determine the applicability of the random pore model with intraparticle diffusion for the determination of the reaction kinetics for the combustion of chars particles derived from coals rich in minerals and inertinites. The char particles which were pyrolysed at 900 °C consisted of a dense carbon-containing fraction originating from the inert macerals (mainly inertinites), a high concentration of minerals and carbominerites, pores generated by the devolatilisation of the reactive macerals and cracks as a result of the presence of minerals. Combustion experimentation was carried out with a thermogravimetric analyser using 1 mm particles with 20% (mole) oxygen in nitrogen at 287.5 kPa and low temperatures (450-600 °C) and with high gas flow rates. The random pore model with intraparticle diffusion (pores and cracks) was solved numerically according to a method consisting of a step-wise regression procedure. This was achieved by using carbon conversion and reduced time relationships to calculate the structural parameter and the initial Thiele modulus followed by determination of an initial lumped reaction rate and validation with conversion versus real time results. The model is characterised by a decreasing Thiele modulus (increasing porosity) occurring during the reaction period which gives rise to a transition to a chemically controlled reaction system. It was found that the initial overall reaction rate was controlled by intraparticle diffusion with an increasing influence with increasing temperature.     

Effect of dual-initiator on low temperature curing of unsaturated polyester resins

In low temperature composite manufacturing processes, a major concern is how to control the resin gel time and cure time and how to achieve a high resin conversion with low residual volatile organic chemicals. In this study, a cobalt promoter catalyzed dual-initiator system was used to control the reaction rate and resin conversion of unsaturated polyester resins. A mechanistic kinetic model was developed to predict the reaction kinetics with dual initiators. This model can be used to simulate the isothermal and dynamic reaction rate and conversion profiles. It can also be utilized to predict the effect of promoter concentration on UP resin cured at low temperatures. The dual-initiator system was applied in the vacuum-assisted resin transfer molding process at room temperature. The kinetic model, in conjunction with the heat transfer analysis, was able to successfully predict the temperature profiles during the molding processes.     

ZnFe2O4高温煤气脱硫剂的还原与硫化

采用共沉淀法制备了ZnFe2O4高温煤气脱硫剂,并在动态热天平上对其还原和硫化行为进行了研究,分别考察了温度、反应气氛对脱硫性能的影响。低于300℃,还原反应基本不发生：在450℃出现ZnFe2O4脱硫剂的最大还原速率：CO还原能力远不及ZnFe2O4脱硫剂硫化反应速率与浊度、H2S浓度成正比,300℃左右出现ZnFe2O4脱硫剂的最大硫化速率。还原与硫化反应可用等效应粒子模型描述,ZnFe2O4脱硫剂的还原与硫化反应存在控制段的转移。     

表面积效应对不同性质原油热力学行为影响研究

针对轻、重质油油藏注空气开发机理,选取典型轻、重质油样进行热重实验,采用改进的Ozawa-Flynn-Wall等转化率法对比分析了不同性质原油三种氧化阶段的热行为和动力学特征,同时探讨了表面积效应对轻、重质原油氧化反应的影响。研究表明：①各氧化阶段之间存在过渡区域,转化率的准确选取对动力学参数至关重要。②轻、重质原油不同氧化阶段的氧化特征存在明显差异,轻质油以低温氧化为主,燃料沉积和高温氧化不显著,且低温氧化、燃料沉积、高温氧化阶段的起始温度更低,更易诱发氧化反应;重质油燃料沉积和高温氧化显著,氧化反应速度更快。③表面积效应导致轻质油低温氧化活化能降低15%以上,峰值温度降低7~17℃。重质油燃料沉积和高温氧化显著增强,燃尽温度下降10~17℃。     

The effect of carbon dioxide during the desulfurization of flue gas with Mardin–Mazıdagı phosphate rock

The effects of temperature, CO₂ concentration and particle size on simultaneous calcination/sulfation of Mardin–Maz?dag? phosphate rock in fluidized-bed reactor were investigated. For this, a raw sample was exposed to calcination and sulfation processes in a fluidized-bed reactor to determine the effects of parameters by using a model gas mixture similar to the flue gas composition. The calcination ratio increased with increasing temperature and decreasing particle size, but decreased with increasing CO₂ concentration. In sulfation process, however, sulphate conversion ratio increased with increasing CO₂ ratio and decreased with decreasing particle size. The sulfation reaction is well represented by the shrinking core model and can be divided into two regions with different rate controlling step. For low conversions, the controlling step was found to be chemical reaction at the interface, but the diffusion through the product layer for high conversion. The activation energies for the chemical reaction at the interface and diffusion through the product layer cases were calculated as 100 and 296 kJ mol^?1, respectively.     

H2O和SO2对Mn-Fe/MPS催化剂用于NH3低温还原NO的影响

研究了H2O和SO2对Mn-Fe/MPS催化剂低温下选择性催化NH3还原(SCR)NO的影响. 结果表明,Mn-Fe/MPS催化剂具有良好的催化活性,在空速为20000 h-1、反应温度433 K时,NO的SCR转化率达99.1%. 在反应温度低于413 K时,水蒸汽(10%, j)在一定程度上降低了催化活性;超过433 K时,这种影响可完全消除,NO的SCR转化率达到97.8%以上. 低浓度SO2(100′10-6)存在条件下,443 K时催化效率仍可稳定在97.2%. 在水和SO2共存的情况下,生成的硫酸盐和亚硫酸盐沉积在催化剂表面导致催化剂逐渐失活,FT-IR测试也表明伴随SCR反应生成了硫酸铵. 提高反应温度可以延缓催化剂的失活. 此外还研究了不同活化温度对催化剂活性恢复的影响,结果表明,当活化温度达到773 K时,催化剂活性可以完全恢复. 本研究中的催化剂的综合性能优于目前文献报道的其他催化剂.     

生物质气催化合成甲醇的热力学分析

由生物质气合成甲醇是一复杂反应系统,本文计算了其中各个反应的反应热和平衡常数与温度的关系.并以CO 21.5%、CO₂ 22.8%、H₂ 52.5%、N₂ 3.2%的气体模拟生物质气,用平衡常数法计算了在473.15～553.15 K、3～6 MPa下的平衡组成、碳的平衡转化率和所得甲醇的浓度.计算结果表明,这一体系中,主要是CO+H₂生成甲醇.低温和高压有利于提高碳的平衡转化率和甲醇的浓度.并用工业C306催化剂验证了上述规律的正确性.由于反应既受热力学控制,又受动力学控制,在3 MPa时碳的转化率在533.15 K时达到最大,接近平衡转化率.随压力升高,甲醇产率及液相产物中的浓度逐渐升高.     

低冰镍转炉渣中钴的氧压酸浸行为及其动力学

研究了转炉渣中钴氧压硫酸体系选择性浸出过程的行为及其动力学。通过改变搅拌速度、反应温度、硫酸浓度、氧分压、物料粒度以及反应时间等浸出条件,考察钴浸出率的变化及影响,获得转炉渣中钴的浸出动力学规律。结果表明,钴的浸出率随着温度、酸度、氧分压的增加而增加;硫酸质量浓度大于0.4 mol·L^-1会导致铁大量溶出;浸出过程符合未反应芯收缩核模型,前期受化学反应控制,然后转变为混合控制,后期受固体产物层扩散控制。化学反应控制和固体产物层扩散控制过程的活化能分别为43.19 kJ·mol^-1 和10.49 kJ·mol^-1。化学反应控制过程对硫酸浓度、氧分压及粒度的反应级数分别为0.79、0.85和 -0.95。     

Kinetic Study of Co-β-Zeolite for Selective Catalytic Reduction of NOx with Propane

The effects of grain size, space velocity, temperature and reactant concentration on the kinetics of NOx reduction with propane over Co-β-zeolite catalyst were investigated. The external mass transfer phenomenon was examined by varying the space velocity. The results show that the transfer can be negligible when the space velocity is greater than 60000 h-1 in low temperature range. However, the transfer exists at high temperatures even when the space velocity reaches a high level.Variation of the catalyst grain size from 0.05 to 0.125 mm does not change the conversion rate of NOx. The concentrations of components, NOx, C3H8 and O2, were also investigated to have a better understanding of mechanism. Based on the experimental data, the selectivity formula was proposed. The results shows that lower temperature is helpful to get higher selectivity as the activation energy of hydrocarbon oxidation, Ea,2, is greater than that of NOx reduction, Ea,1, (Ea,2＞Ea,1). High NOx concentration and low C3H8 concentration are beneficial to high selectivity. However in order to maintain high activity simultaneously, the temperature and C3H8 concentration should be high enough to promote NOx reduction. 10%(ψ) H2O and 75×10-6(ψ) SO2 were introduced into the reaction system, and Co-β-zeolite shows strong resistance to water and SO2.     

羟基聚硅氧烷一步合成的速率研究

以四甲基氢氧化铵为催化剂,八甲基环四硅氧烷为单体,水为封端剂,一步合成羟基聚硅氧烷。采用凝胶渗透色谱(GPC)测定上述一步合成法的转化率,并建立转化率一时间关系曲线的模型函数(Bolzman函数),获得聚合过程中的重要特征参数：最大转化速率rm,极限转化率x(∞)等。研究表明．温度升高,rm加快,x(∞)降低;催化剂浓度增加,rm加快,x(∞)也增加,而转化速率与催化剂浓度在一定的范围内呈l级动力学关系;水浓度增加,rm降低,同时x(∞)也降低。     

工艺条件对耐硫变换催化剂COS转化活性以及甲硫醇生成量的影响

模拟工业装置的工艺条件,考察了原料气中CO和H2S含量、温度和水气比等因素对耐硫变换催化剂COS转化活性和甲硫醇生成量的影响。结果表明,当原料气中CO和H2S含量较高时,会有甲硫醇生成,且其生成量随着CO和H2S含量增加而增加;受平衡的影响,原料气中H2S含量升高时,COS转化率降低;增加反应温度,可以提高COS的氢解反应活性,并减少甲硫醇的生成,但不利于COS的水解反应。水气比具有提高COS转化活性并减少甲硫醇生成的双重作用:水气比较低时,其值从0增加到0.2,COS转化率从89.65%增加到97.82%,表明COS的水解反应比氢解反应更容易进行;当水气比为0.3时,反应后的尾气中只有微量甲硫醇生成,当水气比大于0.4时,反应后几乎无甲硫醇生成。     

A kinetic study on bulk thermal polymerization of styrene

The kinetics of bulk thermal polymerization of styrene over the range of 100–200 °C has been studied based on three stage polymerization model (TSPM) in this paper. TSPM plots showed that the whole polymerization course only exhibits two stages, low conversion stage and gel effect stage, which is consistent with TSPM as the reaction temperature is higher than the glass transition temperature of polystyrene. It was found that the critical conversion, x₁, for the transition from low conversion stage to gel effect stage is independent of the reaction temperature and approximately equal to 0.5. In addition, the apparent reaction rate constants obtained from TSPM plots could be correlated to temperature by Arrhenius equation. Expressions predicting number-average molecular weight were also derived according to TSPM. Using the expressions to treat experimental data available in the literature, it was found that number-average molecular weight is independent of the conversion and relative to the reaction temperature at low conversion stage. However, it varies with the conversions at gel effect stage and the variations are more obvious as the reaction temperature rises.     

Optimization of the coordination–insertion ring‐opening polymerization of poly(p‐dioxanone) by programmed decreasing reaction temperatures

The optimization of the synthesis of poly(p‐dioxanone), by ring‐opening polymerization with tin II bis(2‐ethylhexanoic acid) as the catalyst, was conducted by a new method in which programmed decreasing reaction temperatures were employed. The results were compared with those obtained for polymerization reactions performed at constant temperatures in the 80–180°C range. In the novel method, the temperature was gradually reduced, as the reaction proceeded, to maintain a maximum polymerization rate and monomer conversion as the monomer was consumed. The experiments performed at constant temperatures confirmed previous reports that the bulk polymerization of 1,4‐dioxan‐2‐one is an equilibrium polymerization reaction. With increasing polymerization temperature, the initial rate of polymerization increased, but the monomer conversion, reaching equilibrium, decreased. High conversions were obtained at low temperatures and long reaction times. Therefore, reducing the reaction temperature, to ensure working conditions that guaranteed the maximum polymerization rate and monomer conversion, could optimize the polymerization process. These conditions were calculated under the assumption of equilibrium polymerization reaction kinetics. With our proposed method, a 71% conversion was achieved in half the time needed when the polymerization was performed at a constant temperature of 120°C. Similarly, a 78% conversion was obtained with our proposed method in only a third of the time employed when the reaction was carried out at a constant temperature of 80°C. Our method guarantees high conversions in shorter times and a gradual reduction of the polymerization temperature. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 659–665, 2005     

催化裂化汽油中特征硫化物噻吩的催化氧化脱硫

以负载金属铈的分子筛为催化剂,在H2O2-HCOOH体系中,对催化裂化（FCC）汽油中特征硫化物噻吩（C4H4S）的正庚烷溶液进行了氧化脱硫研究。考察了氧化剂用量、溶剂、氧化时间、氧化温度、相转移剂等因素对噻吩脱除效果的影响,并对对噻吩的氧化反应历程进行了初步的探讨。实验结果表明：以负载金属铈的分子筛为催化剂,在反应温度50℃,反应60min, H2O2：S＝10：1（mol/mol）,H2O2：HCOOH＝1：1（V/V）的条件下,正庚烷溶液C4H4S的脱除率达到了78.2％,加入乳化剂OP可使C4H4S的脱硫率达到94.5％,但四丁基溴化胺（TBAB）的加入使氧化后的样品中出现了噻吩的溴代产物。     

Cl含量对钙基吸收剂微观结构以及动力学性能的影响

通过浸渍法向分析纯CaCO₃中添加Cl,在双固定床反应器系统和热重分析仪上研究了其对钙基吸收剂循环捕集CO₂性能的影响,利用离子反应模型对添加Cl后吸收剂化学反应控制阶段进行动力学分析。结果显示：Cl对钙基吸收剂循环捕集CO₂性能具有不利影响。当Cl/Ca摩尔比大于0.25%后,随Cl/Ca摩尔比增加,化学反应控制阶段反应速率和持续时间均减小,导致在该阶段最终碳酸化转化率降低。对添加Cl前后吸收剂孔隙分布特性进行分析发现,添加Cl导致煅烧后吸收剂烧结加剧,比表面积降低,10~120nm范围内孔分布减少,导致CO₂在吸收剂内部扩散阻力增加,同时能与CO₂反应的CaO量减少,这是导致吸收剂化学反应控制阶段碳酸化反应速度较慢、最终碳酸化转化率较低的主要原因。鉴于Cl的不利影响,在选择钙基材料作为CO₂吸收剂或合成高活性复合吸收剂时,应避免吸收剂中Cl含量过高。     

气化参数对气流床粉煤气化影响实验研究

为评价和优化中国高、低灰熔点煤气化运行参数对气流床气化特性的影响,在1600℃的一维常压沉降式气流床气化实验系统上,着重研究了中国典型高、低灰熔点煤在1200～1600℃温度范围内、O／C摩尔比在0．9～1.2范围内的干煤粉气化特性。结果表明：随着温度的升高,产气中CO、H2含量逐渐增多,CO2、CH4含量逐渐减少,碳转化率有很大提高;随着O／C的增加,CO、H2含量不断减少,CO2逐渐增加;煤的灰熔融性也是影响煤气组分一个重要因素,当气化反应温度接近煤灰熔点温度时,煤气组分（CO＋H2＋CH4）达到一个最大值。