首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 62 毫秒
1.
在格林函数的框架内,研究横场下反铁磁薄膜系统在不同波矢方向上的自旋波,分析横场、反铁磁耦合和薄膜厚度等薄膜参数对自旋波谱分布的影响.  相似文献   

2.
介绍了在磁性薄膜材料中的交换耦合的研究进展。制备了铁磁/反铁磁/铁磁3层结构不同成分的薄膜。利用X射线粉末衍射(XRD)、扫描电镜(SEM)、透射电镜(TEM)等测试分析技术,系统研究了磁性多层薄膜的相组成、界面及微观结构等。利用超导量子干涉仪(SQUID)研究薄膜的磁、电性能和交换耦合。在Co/反铁磁/Fe结构中发现了非常明显的与温度相关的铁磁/反铁磁界面耦合与铁磁/铁磁层间耦合之间的竞争效应。含有不同铁磁层Fe、Co、Fe20Ni80的3层膜FM1/Cr2O3/FM2对交换耦合随温度的变化存在较强的影响,发现铁磁层的磁晶各向异性和跟Cr2O3接触的自旋非对称性反射系数体系的界面和层间耦合有很大的影响。铁磁层对FM/AFM的交换耦合强度的影响甚大,这种影响和铁磁层的各向异性的相关性要强于和铁磁层饱和磁化强度的相关性。通过面内预加场和场冷的方式,在易轴互相垂直的[Pt/Co]n/NiFe/NiO异质结中实现了交换偏置的4种状态,可等温调控偏置。研究了Co/NiO反点阵列和连续膜的交换偏置,与连续膜相比,纳米反点阵列既能增大偏置,也能减小偏置,具有更高的热稳定性。  相似文献   

3.
测量了FeCo薄膜在0.5~8GHz频率范围内的复数磁导率谱,通过改变外加磁场Hex的方向、大小,研究磁导率虚部共振曲线出现的磁滞现象。验证了样品铁磁共振频率fr的平方值随正向Hex线性变化的规律;观察到Hex与样品磁化方向相反时,共振曲线的磁滞现象,尤其是Hex的值接近矫顽力Hc时,共振曲线出现双峰,反映了铁磁薄膜中部分磁矩随着反向Hex逐渐增大逐步翻转的磁化动力学过程。由铁磁共振公式拟合磁谱虚部曲线,计算了双共振峰出现时薄膜中磁矩发生翻转的比例。  相似文献   

4.
采用脉冲激光沉积法制备了稀土掺杂钙钛矿锰氧化物Pr2/3Sr1/3MnO3(PSMO)外延薄膜,研究了薄膜在磁场、激光和电流作用下的自旋输运特性.在低温铁磁金属相,激光作用使薄膜的电阻增大,而磁场和电流则诱导电阻减小;在高温顺磁绝缘态,外场诱导均使电阻减小.在铁磁金属相,外场诱导输运特性的变化可归结于外场对体系电子自旋系统的影响:磁场和电流加强材料中eg电子和t2g局域电子间的自旋平行,增强了双交换作用;激光作用可产生光致退磁效应,减弱双交换作用.在顺磁绝缘态,场致电阻降低源于外场致使小极化子的退局域化效应.  相似文献   

5.
基于Monte Carlo模拟,研究了准二维4×4量子点阵列中交换相互作用常数J、偶极相互作用常数D、磁晶各向异性常数K对自旋组态和相关磁特性的影响.模拟结果表明,量子点阵列和单个量子点表现出完全不同的磁特性,即量子点阵列表现为顺磁性,而单个量子点则为铁磁性;分析不同外磁场下体系自旋组态的变化可以很好地解释模拟结果.  相似文献   

6.
磁流体在交变磁场中的热效应研究   总被引:7,自引:0,他引:7  
王煦漫  古宏晨  杨正强  王建华 《功能材料》2005,36(4):507-508,512
制备了平均粒径分别为4、6 和8nm 的Fe3O4 粒子,将其分散在不同的介质中,在63kHz、7kA/m的交变磁场中研究其热效应。实验结果显示,粒径较大的Fe3O4 粒子具有较高的产热比功率(SAR),Fe3O4 粒子经过表面处理后SAR显著增加,而且SAR随表面活性剂不同而不同,还显示SAR与磁场强度的平方成正比。  相似文献   

7.
通过高真空直流磁控溅射的方法制备了结构为//Ta(5nm)/Co75 Fe25(5nm)/Cu(2.5nm)/Co75Fe25(5nm)/Ir20 Mn80(12nm)/Ta(8nm)的顶钉扎自旋阀结构多层膜,研究了磁场循环次数、反向饱和场等待时间和磁场变化率对自旋阀结构多层膜磁化反转过程的影响.结果表明,磁场循环次数和反向饱和场等待时间对自由层的磁化反转过程没有影响,而在被钉扎层中出现了练习效应和时间效应;磁场变化率对被钉扎层和自由层的前、后支反转场的影响变化趋势相似,但反铁磁层对被钉扎层的反转有一定的影响.  相似文献   

8.
铁磁层/导电层/铁磁层多层膜中巨磁阻抗效应理论*   总被引:2,自引:0,他引:2  
禹金强  周勇  蔡炳初  徐东 《功能材料》2001,32(2):129-131
采用经典电磁理论,对铁磁层/导电层/铁磁层(M/C/M)多层膜中出现的巨磁阻抗效应进行了理论分析。对于单轴横向磁各向异性多层膜,理论计算结果表明:高频阻抗在某一外加磁场(近似等于等效各向异性场)下出现最大值,铁磁层和导电层电阻率相关较大的多层膜中将出现较强的巨磁阻抗效应。多层膜在1MHz附近即可出现远大于单层膜的阻抗变化比。多层膜理论计算与实验结果能够较好地符合。  相似文献   

9.
根据Landau-Lifshitz理论计算模拟了Co2Z型平面六角晶系铁氧体材料的磁谱,并讨论了饱和磁化强度帆、各向异性场风和风、阻尼系数α对材料磁谱的影响,提出了起始磁导率、共振频率、共振峰值的调控方法.对要求在2GHz下磁导率实部和虚部均〉10的新型Co2Z材料进行仿真设计,计算出新材料的磁谱参数以及本征参数,列出了一系列满足性能要求的本征参数(磁化强度帆、各向异性场风和风)及阻尼系数口,对新材料的研制具有准确的理论指导作用。  相似文献   

10.
《真空》2015,(6)
电子回旋波共振(ECWR)技术是利用电磁波与电学各向异性材料(如带有外加静磁场的低压等离子体)的相互作用来实现的,该技术可在低压力下产生高密度等离子体,广泛用于微电子刻蚀、薄膜材料沉积等加工过程。等离子体的参数对刻蚀速率、表面成膜质量有着至关重要的影响,因此进行等离子体参数的测量研究能够促进电子回旋波共振技术的发展与应用。本文设计了朗缪尔探针检测装置,使用OES光谱检测仪对ECWR设备放电时的等离子体参数进行检测,并对检测结果进行了分析。结果表明,当直流电流强度为4.1A时,系统内部发生了电子回旋共振效应。  相似文献   

11.
In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.  相似文献   

12.
Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……  相似文献   

13.
14.
A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.  相似文献   

15.
On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……  相似文献   

16.
Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.  相似文献   

17.
In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M2(B,C), (W,Mo)2(B,C), M3(B,C), M23(B,C)6 type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm2. The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K1 mill housing of bar mill.  相似文献   

18.
The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...  相似文献   

19.
正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from  相似文献   

20.
正The review group of Asia Pacific Laboratory Accreditation Cooperation(APLAC)carried out a 4-day peer review of the proficiency testing provider(PTP)for China National Accreditation Service for Conformity Assessment(CNAS)from July 28 to 31,2014.CNAS passed the PTP review with excellent performance.Two senior peer reviewers of APLAC made a comprehensive,rigorous and detailed review of CNAS’s PTP accreditation activities,and made the on-spot inspection of the review groups in Shanghai and Shenzhen respectively.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号