Molten-Salt Synthesis of Ba1–xPbxTiO3 in the System BaTiO3–PbCl2

Ba_{1– x} Pb _x TiO₃ powder with a fixed composition was prepared by the reaction of BaTiO₃ powders with molten PbCl₂at various PbCl₂/BaTiO₃ molar ratios at 600° and 800°C in a nitrogen atmosphere. When 0.1 μm powder was used, the reaction was finished when x = 0.9. Two phases of BaTiO₃and a solid solution of Ba_{1– x} Pb _x TiO₃ coexisted, but the final phase gave a solid solution of Ba_{1– x} Pb _x TiO₃ at 800°C. When 0.5 μm powder was used, the two phases coexisted in the products at 600°C at PbCl₂/BaTiO₃= 1.0. A sintered compact of Ba_{1– x} Pb _x TiO₃ powders solid solution was prepared by hot isostatic pressing, and its dielectric constant was measured in the temperature range 20°–550°C.     

Synthesis of Y-Doped BaTiO3–(Bi1/2K1/2)TiO3 Lead-Free Positive Temperature Coefficient of Resistivity Ceramics and Their PTC Effects

As a lead-free positive temperature coefficient of resistivity (PTCR) material, (1– x mol%) BaTiO₃– x mol% (Bi_1/2K_1/2) TiO₃– y mol% Y₂O₃–0.5 mol% TiO₂ (BT– x BKT–2 y Y–0.5TiO₂) systems were prepared by the conventional solid-state reaction method. All samples containing <2 mol% BKT sintered in air possessed relatively low room-temperature resistivity (ρ₂₅) and high positive temperature coefficient (PTC) effect. However, when the BKT content exceeded 2 mol%, the sample was not semiconductive after sintering in air. The effects of sintering schedule on the properties of PTCR ceramics were discussed. The results showed that the optimum composition of BT–1BKT–0.2Y–0.5TiO₂, sintered at 1330°C for not-soaking and then fast quenched in air, achieved rather low ρ₂₅ of 28 Ω·cm and a high jump of resistivity (maximum resistivity [ρ_max]/minimum resistivity [ρ_min]) of 4.0 orders of magnitude with T _c about 155°C. The ρ₂₅ of the as-sintered sample could be further reduced to about 10 Ω·cm by annealing in N₂ at 450°C for 30 min, accompanied decrease on the PTC effect.     

Fabrication of Na0.5Bi0.5TiO3–BaTiO3-Textured Ceramics Templated by Plate-Like Na0.5Bi0.5TiO3 Particles

Textured 0.94Na_0.5Bi_0.5TiO₃–0.06BaTiO₃ (NBT–6BT) ceramics were fabricated by templated grain growth (TGG) using anisotropically shaped Na_0.5Bi_0.5TiO₃ (NBT) templates. Platelet NBT was synthesized by the topochemical technique, using precursor Na_0.5Bi_4.5Ti₄O₁₅ (NBIT). The NBT particles have an average length of 10–15 μm and a thickness of 1 μm, which are suitable templates for obtaining textured ceramics (especially NBT-based ceramics) by the TGG process. This study revealed that the NBT templates are effective in inducing grain orientation in NBT–6BT ceramics. For NBT–6BT ceramics textured with 5 vol% NBT templates, a Lotgering factor of 0.87 and a d ₃₃ of 299 pC/N are given.     

High Q Microwave Dielectric Ceramics in (Ni1−x Znx)Nb2O6 System

(Ni_{1− x} Zn _x )Nb₂O₆, 0≤ x ≤1.0, ceramics with >97% density were prepared by a conventional solid-state reaction, followed by sintering at 1200°–1300°C (depending on the value of x ). The XRD patterns of the sintered samples (0≤ x ≤1.0) revealed single-phase formation with a columbite ( Pbcn ) structure. The unit cell volume slightly increased with increasing Zn content ( x ). All the compositions showed high electrical resistivity (ρ_dc=1.6±0.3 × 10¹¹Ω·cm). The microwave (4–5 GHz) dielectric properties of (Ni_{1− x} Zn _x )Nb₂O₆ ceramics exhibited a significant dependence on the Zn content and to some extent on the morphology of the grains. As x was increased from 0 to 1, the average grain size monotonically increased from 7.6 to 21.2 μm and the microwave dielectric constant (ɛ'_r) increased from 23.6 to 26.1, while the quality factors ( Q _u× f ) increased from 18 900 to 103 730 GHz and the temperature coefficient of resonant frequency (τ_f) increased from −62 to −73 ppm/°C. In the present work, we report the highest observed values of Q _u× f =103 730 GHz, and ɛ'_r=26.1 for the ZnNb₂O₆-sintered ceramics.     

Transmission Electron Microscopy Microstructure of 0.95(Na0.5K0.5)NbO3–0.05BaTiO3 Ceramics

Microstructural characterizations using transmission electron microscopy on 0.95(Na_0.5K_0.5)NbO₃–0.05BaTiO₃ ceramics sintered at 1030°–1150°C for 2 h were carried out. The liquid phase was found at the triple junction of the grains in all specimens and abnormal grain growth occurred in the presence of the liquid phase. Abnormally grown grains whose shapes were cuboidal were well developed. Anisotropically faceted amorphous liquid phase pockets were observed inside the grain in a specimen sintered at 1060°C for 2 h. The interface between the grain and the liquid matrix was flat and some were identified to be {100} planes of the grains. A certain amount of liquid at the sintering temperature of 1060°C enhanced the abnormal grain growth and contributed to the improvement of the piezoelectric properties.     

Residual α–Si3N4 in O' Crystals in CeO2-Doped O'+β' SiAlON Ceramics

The microstructure of a pressureless sintered (1605°C, 90 min) O'+β' SiAlON ceramic with CeO₂ doping has been investigated. It is duplex in nature, consisting of very large, slablike elongated O' grains (20–30 μm long), and a continuous matrix of small rodlike β' grains (< 1.0 μm in length). Many α-Si₃N₄ inclusions (0.1–0.5 μm in size) were found in the large O' grains. CeO₂-doping and its high doping level as well as the high Al₂O₃ concentration were thought to be the main reasons for accelerating the reaction between the α-Si₃N₄ and the Si-Al-O-N liquid to precipitate O'–SiAlON. This caused the supergrowth of O' grains. The rapid growth of O' crystals isolated the remnant α–Si₃N₄ from the reacting liquid, resulting in a delay in the α→β-Si₃N₄ transformation. The large O' grains and the α-Si₃N₄ inclusions have a pronounced effect on the strength degradation of O'+β' ceramics.     

Crystal Structure and Characterization of Pure and Ag-Doped (La1−xYx)2Ba2CaCu5Oz (0≤x≤0.5) Superconductors

Pure and 5 wt% of Ag-doped (La_{1− x} Y _x )₂Ba₂CaCu₅O_z superconducting compounds for x =0–0.5 have been prepared. Analysis of X-ray diffraction patterns shows that the samples are essentially in the single-phase form and they could be refined using the P 4 /mmm space group in a tetragonal cell. The typical lattice parameters are found to be a = b =3.879 Å, c =11.646 Å for x =0 and a = b =3.856 Å, c =11.576 Å for x =0.5 samples. The detailed crystal structure parameters are presented. The average grain size values from scanning electron microscope images are found to be in the order of 1–3 μm. Temperature variations of ac susceptibility and electrical resistivity have been measured. Superconducting transitions with diamagnetic T _c ranging from 60 to 75 K have been observed, with the maximum T _c for the x =0.25 sample. Ag-doped samples exhibit improved inter-granular coupling and homogeneous oxygenation.     

Film Synthesis of Y3Al5O12 and Y3Fe5O12 by the Spray–Inductively Coupled Plasma Technique

Thin films of yttrium aluminum garnet (YAG, Y₃Al₅O₁₂) and yttrium iron garnet (YIG, Y₃Fe₅O₁₂) were synthesized on single-crystal Al₂O₃ substrates by a modification of spray pyrolysis using a high-temperature inductively coupled plasma at atmospheric pressure (spray–ICP technique). Using this technique, films could be grown at faster rates (0.12 μm/min for YAG and 0.10 μm/min for YIG) than using chemical vapor deposition (0.005–0.008 μm/min for YAG) or sputtering (0.003–0.005 μm/min for YIG). The films were dense and revealed a preferred orientation of (211). The growth of YIG was accompanied by coprecipitation of α-Fe₂O₃. The coprecipitation, however, could be largely suppressed by preliminary formation of a Y₂O₃ layer on the substrate.     

Microwave Dielectric Properties of CaTiO3-CaAl1/2Nb1/2O3 Ceramics Doped with Li3NbO4

The microwave dielectric properties of CaTi_{1− x} (Al_1/2Nb_1/2) _x O₃ solid solutions (0.3 ≤ x ≤ 0.7) have been investigated. The sintered samples had perovskite structures similar to CaTiO₃. The substitution of Ti⁴⁺ by Al³⁺/Nb⁵⁺ improved the quality factor Q of the sintered specimens. A small addition of Li₃NbO₄ (about 1 wt%) was found to be very effective for lowering sintering temperature of ceramics from 1450–1500° to 1300°C. The composition with x = 0.5 sintered at 1300°C for 5 h revealed excellent dielectric properties, namely, a dielectric constant (ɛ_r) of 48, a Q × f value of 32 100 GHz, and a temperature coefficient of the resonant frequency (τ_f) of −2 ppm/K. Li₃NbO₄ as a sintering additive had no harmful influence on τ_f of ceramics.     

Electrical Resistivity Surface for FeO-Fe2O3-P2O5 Glasses

The dc electrical properties and microstructure of x (FeO-Fe₂O₃)-(100 – x )P₂O₅ glasses were investigated up to a maximum of x = 75 mol%. Results indicate that, in general, the minimum resistivity of the glass does not occur at equal Fe^2+] and Fe^3+] concentrations, although for the special case where x = 55 mol% the minimum does occur at Fe^2+]/Fe total = 0.5, as reported by other investigators. Evidence presented shows that the position of the minimum resistivity is a function of total iron content. The minimum shifts to glasses richer in Fe^2+] at higher total iron concentrations.     

Topochemical Synthesis of Plate-Like Na0.5Bi0.5TiO3 from Aurivillius Precursor

Plate-like Na_0.5Bi_0.5TiO₃ (NBT) particles with perovskite structure were synthesized by topochemical microcrystal conversion from plate-like particles of layer-structured Na_0.5Bi_4.5Ti₄O₁₅ (NBIT) at 950°C in NaCl molten salt. As the precursors of NBT, plate-like NBIT particles were first synthesized by molten salt process by the reaction of Bi₄Ti₃O₁₂, Na₂CO₃, and TiO₂. After the topochemical reactions, layer-structured NBIT particles were transformed to the perovskite NBT platelets. NBT particles with a thickness of approximately 0.5 μm and a length of 10–15 μm retained the morphology feature of the precursor. High-aspect-ratio NBT platelets are suitable templates to obtain textured ceramics (especially NBT-based ceramics) by (reactive) template grain growth process.     

B6O–c-BN Composites Prepared by High-Pressure Sintering

High-pressure sintering behavior in the B₆O– c -BN system was investigated using in-laboratory-synthesized B₆O and commercially available c -BN powders (with an average grain size of 0.5, 3, or 6 μm). No reaction occurred between the two components under the high-pressure (4–6 GPa) and high-temperature (1500°–1800°C) conditions that have been investigated. Well-dispersed, sintered B₆O– x ( c -BN) composites (where x = 0–60 vol%) of almost-full density were prepared by sintering at a pressure of 6 GPa and temperature of 1800°C for 20 min. The maximum Vickers microhardness (46 GPa) of these composites was attained by adding 40 vol% c -BN with an average grain size of 0.5 μm. The fracture toughness of these composites increased as the c -BN content increased; the maximum fracture toughness (1.5–1.8 MPa^.m^1/2) was observed for x = 40–60 vol%. Crack deflection along the B₆O– c -BN grain boundary contributed to increasing the fracture toughness.     

Kinetics of Templated Grain Growth of 0.65Pb(Mg1/3Nb2/3)O3·0.35PbTiO3

Single-crystal layers of 0.65Pb(Mg_1/3Nb_2/3)O₃·0.35PbTiO₃ (PMN-35PT) were grown heteroepitaxially on {001}-BaTiO₃ template crystals. A {001}-BaTiO₃ crystal was embedded in a fine-grained matrix of PMN-35PT containing excess PbO and heated between 950° and 1150°C for 0–5 h. The initial growth of the PMN-35PT on the {001} surface and the growth of the matrix grains both displayed a t ^1/3 dependence which is characteristic of diffusion-controlled growth. Growth was limited to ∼100–150 μm due to the significantly reduced driving force at longer times because of matrix coarsening and porosity evolution.     

Fracture Characteristics of Czochralski-Grown Y3Al5O12

The fracture surfaces of single-crystal Y₃A1₅O₁₂ (YAG) have been examined in detail using differential interference microscopy and atomic force microscopy. In YAG crystals grown in 1977 by the Czochralski method strikingly regular undulations of microscopic and submicroscopic dimensions (4–20 nm in amplitude, 1–20 μm in wavelength) are observed on every fracture surface. The undulations do not exhibit typical characteristics of Wallner lines; furthermore, they are not observed in identical fracture tests for YAG crystals grown in 1990 by the Czochralski method. Transmission electron microscopy reveals that the crystals grown in 1977 exhibit a periodic fluctuation of the ratio of the concentrations of aluminum to yttrium, suggesting that the fracture surface features are caused by periodic astoichiometry.     

Synthesis of Micron-Scale Platelet BaTiO3

Micron-scale platelet barium titanate was synthesized using a twostep molten salt and topochemical technique. Plate-like BaBi₄Ti₄O₁₅ was first synthesized as a precursor by molten salt synthesis. Then, Bi³⁺ in the precursor was replaced by Ba²⁺ and formed perovskite-structure BaTiO₃ through a topochemical reaction. The BaTiO₃ single crystals have an average size of 5–10 μm and a thickness of 0.5 μm. The purpose of this article is to control the particle shape with desired structure. High aspect ratio BaTiO₃ platelets are suitable templates to obtain textured ceramics (especially Pb(Mg_1/3Nb_2/3)O₃–32.5PbTiO₃) by the templated grain growth process.     

Influence of Sintering Temperature on Grain Growth and Phase Structure of Compositionally Optimized High-Performance Li/Ta-Modified (Na,K)NbO3 Ceramics

Microstructure characteristics, phase transition, and electrical properties of (Na_0.535K_0.485)_0.926Li_0.074(Nb_0.942Ta_0.058)O₃ (NKN-LT) lead-free piezoelectric ceramics prepared by normal sintering are investigated with an emphasis on the influence of sintering temperature. Some abnormal coarse grains of 20–30 μm in diameter are formed in a matrix consisting of about 2 μm fine grains when the sintering temperature was relatively low (980°C). However, only normally grown grains were observed when the sintering temperature was increased to 1020°C. On the other hand, orthorhombic and tetragonal phases coexisted in the ceramics sintered at 980°–1000°C, whereas the tetragonal phase becomes dominant when sintered above 1020°C. For the ceramics sintered at 1000°C, the piezoelectric constant d ₃₃ is enhanced to 276 pC/N, which is a high value for the Li- and Ta-modified (Na,K)NbO₃ ceramics system. The other piezoelectric and ferroelectric properties are as follows: planar electromechanical coupling factor k _p=46.2%, thickness electromechanical coupling factor k _t=36%, mechanical quality factor Q _m=18, remnant polarization P _r=21.1 μC/cm², and coercive field E _c=1.85 kV/mm.     

Microstructural Evolution of Crystalline-Oriented (K0.5Na0.5)NbO3 Piezoelectric Ceramics with a Sintering Aid of CuO

The microstructural development of crystalline-oriented (K_0.5Na_0.5)NbO₃ (KNN)-based piezoelectric ceramics during sintering was investigated. The addition of CuO as a sintering aid was found to be effective for fabricating highly oriented and dense KNN ceramics. KNN specimens containing 0.5–1.0 mol% CuO sintered at 1100°C for 1 h were found to have relative densities and pseudo-cubic {100} orientation degrees of 95% or higher. In the early stages of sintering, KNN is formed in the reaction between complementary reactants NaNbO₃ and KNbO₃, after which oriented grain growth proceeds at a relative density of more than 90%. In addition, the results of transmission electron microscopy observation showed that textured KNN ceramics have a unique pectinate-like domain structure with domain walls consisting of {101} planes.     

Superconducting Properties of Barium-Doped (Bi,Pb)2Sr2Ca2Cu3Ox Glass-Ceramics

The Ba-doped superconducting (Bi,Pb)₂Sr_{2- x} Ba _x Ca₂Cu₃O _y and (Bi,Pb)₂Sr₂Ca_{2- x} Ba _x Cu₃O _y (0 ≦ x ≦ 1.0) were prepared by using a melt-quenching method, and the effect of Ba additions on the glass-forming ability and the crystalline phase was examined. The glass-forming ability was not improved by substitution of Ba for Sr or Ca, and particularly BaPbO₃ as well as CaO was observed in the melt-quenched sample of (Bi,Pb)₂SrBaCa₂Cu₃O _y . BaPbO₃ crystals were precipitated in all glass-ceramics with Ba substituted for Sr or Ca. The partial substitution of Ba substituted for Sr was effective for the formation of the high- T _c phase, and (Bi,Pb)₂Sr_1.4Ba_0.6Ca₂Cu₃O _y glass-ceramics obtained by annealing at 830°C for 100 h exhibited superconductivity with a T _c of 103 K, although BaPbO₃ and the low- T _c phase were still largely present.     

Phase Transitions and Electrical Properties of (Na1−xKx)(Nb1−ySby)O3 Lead-Free Piezoelectric Ceramics With a MnO2 Sintering Aid

Lead-free piezoelectric ceramics (Na_{1− x} K _x )(Nb_{1− y} Sb _y )O₃+ z mol% MnO₂ have been prepared by a conventional solid-state sintering technique. Our results reveal that Sb⁵⁺ diffuses into the K_0.5Na_0.5NbO₃ lattices to form a solid solution with a single-phase orthorhombic perovskite structure. The partial substitution of Sb⁵⁺ for B-site ion Nb⁵⁺ decreases the paraelectric cubic-ferroelectric tetragonal phase transition ( T _c) and the ferroelectric tetragonal-ferroelectric orthorhombic phase transition ( T _O–F), and retains strong ferroelectricity. A small amount of MnO₂ is enough to improve the densification of the ceramics. The co-effects of MnO₂ doping and Sb substitution lead to significant improvements in ferroelectric and piezoelectric properties. The ceramics with x =0.45–0.525, y =0.06–0.08, and z =0.5–1 exhibit excellent ferroelectric and piezoelectric properties: d ₃₃=163–204 pC/N, k _P=0.47–0.51, k _t=0.46–0.52, ɛ=640–1053, tan δ=1.3–3.0%, P _r=18.1–22.6 μC/cm², E _c=0.72–0.98 kV/mm, and T _C=269°–314°C.     

Processing and Properties of in Situ-Reinforced α-SiAlONs Stabilized with Y2O3 and Lu2O3

α-SiAlONs with equiaxed and elongated microstructures stabilized with Y₂O₃ and Lu₂O₃ were produced by hot pressing, and the phase structure and room- and high-temperature mechanical properties were assessed. Additional liquid added to the starting composition in the form of 5 wt% rare-earth monosilicate resulted in the formation of elongated microstructures and improvements in room-temperature strength and fracture toughness. The elongated grain growth was promoted by the additional liquid phase, which crystallized to form a secondary grain-boundary phase thought to be J ' (Re₄Si_{2– x} Al _x O_{7+ x} N_{2– x} ). For the equiaxed and the elongated samples, those sintered with Lu₂O₃ showed higher hardness than the comparable Y₂O₃-sintered materials, and, at elevated temperature, the strength retention of the elongated Lu₂O₃ SiAlON was much higher than that of the Y₂O₃ sample, which was attributed to properties of the residual grain-boundary phase associated with the difference in the cationic radius of the stabilizing cation.