A chatter free calibration method for determining cutter runout and cutting force coefficients in ball-end milling

The accuracy of cutting force coefficients plays an important role in predicting reliable cutting force, stability lobes as well as surface location error in ball-end milling. In order to avoid chatter risk of the traditional calibration test with an entire-ball-immersed cutting depth, a cylindrical surface milling method is proposed to calibrate the cutting force coefficients with the characteristics of low cutting depth and varying lead angle. A dual-cubic-polynomial function is also presented to describe the non-uniform cutting force coefficients of the ball part cutting edge and the nonlinear chip size effect on cutting force. The variation of the maximum chip thickness versus the lead angle is established with the consideration of cutter runout. According to the dependence of chip thickness on lead angle, a runout identification method is introduced by seeking the critical lead angle at which one of the cutter flutes is just thoroughly out of cut. Then, a lumped equivalent method is adopted for the low cutting depth condition so that the dual-cubic-polynomial model can be calibrated for the chip size effect and the cutting force coefficients respectively. The accuracy of the proposed calibration method has been validated experimentally with a series of milling tests. The stability examinations indicate that the proposed method has an evident chatter-free advantage, compared with that of varying cutting depth method.     

Modelling and analysis of micro scale milling considering size effect, micro cutter edge radius and minimum chip thickness

This paper presents mechanisms studies of micro scale milling operation focusing on its characteristics, size effect, micro cutter edge radius and minimum chip thickness. Firstly, a modified Johnson–Cook constitutive equation is formulated to model the material strengthening behaviours at micron level using strain gradient plasticity. A finite element model for micro scale orthogonal machining process is developed considering the material strengthening behaviours, micro cutter edge radius and fracture behaviour of the work material. Then, an analytical micro scale milling force model is developed based on the FE simulations using the cutting principles and the slip-line theory. Extensive experiments of OFHC copper micro scale milling using 0.1 mm diameter micro tool were performed with miniaturized machine tool, and good agreements were achieved between the predicted and the experimental results. Finally, chip formation and size effect of micro scale milling are investigated using the proposed model, and the effects of material strengthening behaviours and minimum chip thickness are discussed as well. Some research findings can be drawn: (1) from the chip formation studies, minimum chip thickness is proposed to be 0.25 times of cutter edge radius for OFHC copper when rake angle is 10° and the cutting edge radius is 2 μm; (2) material strengthening behaviours are found to be the main cause of the size effect of micro scale machining, and the proposed constitutive equation can be used to explain it accurately. (3) That the specific shear energy increases greatly when the uncut chip thickness is smaller than minimum chip thickness is due to the ploughing phenomenon and the accumulation of the actual chip thickness.     

Efficient calibration of instantaneous cutting force coefficients and runout parameters for general end mills

This paper aims at developing a unified approach to identify the cutting force coefficients together with the cutter runout parameters for general end mills such as cylindrical, ball, bull nose ones, etc. The cutting forces that are modeled using the instantaneous cutting force coefficients are analyzed and separated into two terms: a nominal component independent of the runout and a perturbation component induced by the runout. The nominal component enables the calibration of the instantaneous cutting force coefficients whereas the runout parameters are determined from the perturbation component. The validity of the present method is demonstrated with simulation and experimented data.     

Effect of cutter runout on process geometry and forces in peripheral milling of curved surfaces with variable curvature

This paper presents a novel method for cutting force modeling related to peripheral milling of curved surfaces including the effect of cutter runout, which often changes the rotation radii of cutting points. Emphasis is put on how to efficiently incorporate the continuously changing workpiece geometry along the tool path into the calculation procedure of tool position, feed direction, instantaneous uncut chip thickness (IUCT) and entry/exit angles, which are required in the calculation of cutting force. Mathematical models are derived in detail to calculate these process parameters in occurrence of cutter runout. On the basis of developed models, some key techniques related to the prediction of the instantaneous cutting forces in peripheral milling of curved surfaces are suggested together with a whole simulation procedure. Experiments are performed to verify the predicted cutting forces; meanwhile, the efficiency of the proposed method is highlighted by a comparative study of the existing method taken from the literature.     

On the dynamics of ball end milling: modeling of cutting forces and stability analysis

This paper presents a dynamic force model and a stability analysis for ball end milling. The concept of the equivalent orthogonal cutting conditions, applied to modeling of the mechanics of ball end milling, is extended to include the dynamics of cutting forces. The tool is divided into very thin slices and the cutting force applied to each slice is calculated and summed for all the teeth engaged. To calculate the instantaneous chip thickness of each tooth slice, the method of regenerative chip load calculation which accounts for the effects of both the surface undulations and the instantaneous deflection is used. To include the effect of the interference of the flank face of the tool with the finished surface of the work, the plowing force is also considered in the developed model. Experimental cutting forces are obtained using a five-axis milling machine with a rotary dynamometer. The developed dynamic model is capable of generating force and torque patterns with very good agreement with the experimental data. Stability of the ball end milling in the semi-finishing operation of die cavities is also studied in this paper. The tangential and radial forces predicted by the method of equivalent orthogonal condition are fitted by the equations F_t = K_t(Z)bh_av and F_r = K_r(Z)F_t, where b is the depth of cut and h_av is the average chip thickness along the cutting edge and Z is the tool axis coordinate. The polynomial functions K_t(Z) and K_r(Z) are the cutting force constants. The interdependency of the axial and radial depths of cut in ball end milling results in an iterative solution of the characteristic equation for the critical width of cut and spindle speed. In addition, due to different cutting characteristics of the cutting edge at different heights of the ball nose, stability lobes are represented by surfaces. Comparison of the time domain simulation for the shoulder removal process in die cavity machining with the analytical predictions shows that the proposed method is capable of accurate prediction of the stability lobes.     

Process simulation using finite element method — prediction of cutting forces, tool stresses and temperatures in high-speed flat end milling

End milling of die/mold steels is a highly demanding operation because of the temperatures and stresses generated on the cutting tool due to high workpiece hardness. Modeling and simulation of cutting processes have the potential for improving cutting tool designs and selecting optimum conditions, especially in advanced applications such as high-speed milling. The main objective of this study was to develop a methodology for simulating the cutting process in flat end milling operation and predicting chip flow, cutting forces, tool stresses and temperatures using finite element analysis (FEA). As an application, machining of P-20 mold steel at 30 HRC hardness using uncoated carbide tooling was investigated. Using the commercially available software DEFORM-2D™, previously developed flow stress data of the workpiece material and friction at the chip–tool contact at high deformation rates and temperatures were used. A modular representation of undeformed chip geometry was used by utilizing plane strain and axisymmetric workpiece deformation models in order to predict chip formation at the primary and secondary cutting edges of the flat end milling insert. Dry machining experiments for slot milling were conducted using single insert flat end mills with a straight cutting edge (i.e. null helix angle). Comparisons of predicted cutting forces with the measured forces showed reasonable agreement and indicate that the tool stresses and temperatures are also predicted with acceptable accuracy. The highest tool temperatures were predicted at the primary cutting edge of the flat end mill insert regardless of cutting conditions. These temperatures increase wear development at the primary cutting edge. However, the highest tool stresses were predicted at the secondary (around corner radius) cutting edge.